Merge branch 'master' of git://git.denx.de/u-boot-spi

6 files changed, 51 insertions, 36 deletions

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index aca385d5e5..5da66a6de0 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -61,13 +61,6 @@ config FSL_DSPI
 	  this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms
 	  use this driver.
 
-config FSL_QSPI
-	bool "Freescale QSPI driver"
-	help
-	  Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
-	  used to access the SPI NOR flash on platforms embedding this
-	  Freescale IP core.
-
 config ICH_SPI
 	bool "Intel ICH SPI driver"
 	help
@@ -188,6 +181,13 @@ config FSL_ESPI
 	  access the SPI interface and SPI NOR flash on platforms embedding
 	  this Freescale eSPI IP core.
 
+config FSL_QSPI
+	bool "Freescale QSPI driver"
+	help
+	  Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
+	  used to access the SPI NOR flash on platforms embedding this
+	  Freescale IP core.
+
 config TI_QSPI
 	bool "TI QSPI driver"
 	help
diff --git a/drivers/spi/cadence_qspi.c b/drivers/spi/cadence_qspi.c
index a5244fff4d..1d50f135c9 100644
--- a/drivers/spi/cadence_qspi.c
+++ b/drivers/spi/cadence_qspi.c
@@ -251,7 +251,7 @@ static int cadence_spi_xfer(struct udevice *dev, unsigned int bitlen,
 		break;
 		case CQSPI_INDIRECT_READ:
 			err = cadence_qspi_apb_indirect_read_setup(plat,
-				priv->cmd_len, dm_plat->mode_rx, cmd_buf);
+				priv->cmd_len, dm_plat->mode, cmd_buf);
 			if (!err) {
 				err = cadence_qspi_apb_indirect_read_execute
 				(plat, data_bytes, din);
diff --git a/drivers/spi/ich.c b/drivers/spi/ich.c
index 00b2fed7b7..caf0103dc3 100644
--- a/drivers/spi/ich.c
+++ b/drivers/spi/ich.c
@@ -649,10 +649,8 @@ static int ich_spi_child_pre_probe(struct udevice *dev)
 	 * ICH 7 SPI controller only supports array read command
 	 * and byte program command for SST flash
 	 */
-	if (plat->ich_version == ICHV_7) {
-		slave->mode_rx = SPI_RX_SLOW;
-		slave->mode = SPI_TX_BYTE;
-	}
+	if (plat->ich_version == ICHV_7)
+		slave->mode = SPI_RX_SLOW | SPI_TX_BYTE;
 
 	return 0;
 }
diff --git a/drivers/spi/spi-uclass.c b/drivers/spi/spi-uclass.c
index 247abfa72b..d9c49e4e8c 100644
--- a/drivers/spi/spi-uclass.c
+++ b/drivers/spi/spi-uclass.c
@@ -164,7 +164,6 @@ static int spi_child_pre_probe(struct udevice *dev)
 
 	slave->max_hz = plat->max_hz;
 	slave->mode = plat->mode;
-	slave->mode_rx = plat->mode_rx;
 	slave->wordlen = SPI_DEFAULT_WORDLEN;
 
 	return 0;
@@ -381,7 +380,7 @@ void spi_free_slave(struct spi_slave *slave)
 int spi_slave_ofdata_to_platdata(const void *blob, int node,
 				 struct dm_spi_slave_platdata *plat)
 {
-	int mode = 0, mode_rx = 0;
+	int mode = 0;
 	int value;
 
 	plat->cs = fdtdec_get_int(blob, node, "reg", -1);
@@ -413,24 +412,22 @@ int spi_slave_ofdata_to_platdata(const void *blob, int node,
 		break;
 	}
 
-	plat->mode = mode;
-
 	value = fdtdec_get_uint(blob, node, "spi-rx-bus-width", 1);
 	switch (value) {
 	case 1:
 		break;
 	case 2:
-		mode_rx |= SPI_RX_DUAL;
+		mode |= SPI_RX_DUAL;
 		break;
 	case 4:
-		mode_rx |= SPI_RX_QUAD;
+		mode |= SPI_RX_QUAD;
 		break;
 	default:
 		error("spi-rx-bus-width %d not supported\n", value);
 		break;
 	}
 
-	plat->mode_rx = mode_rx;
+	plat->mode = mode;
 
 	return 0;
 }
diff --git a/drivers/spi/ti_qspi.c b/drivers/spi/ti_qspi.c
index bb72cb03ec..52520dff63 100644
--- a/drivers/spi/ti_qspi.c
+++ b/drivers/spi/ti_qspi.c
@@ -23,6 +23,9 @@ DECLARE_GLOBAL_DATA_PTR;
 #define QSPI_TIMEOUT                    2000000
 #define QSPI_FCLK			192000000
 #define QSPI_DRA7XX_FCLK                76800000
+#define QSPI_WLEN_MAX_BITS		128
+#define QSPI_WLEN_MAX_BYTES		(QSPI_WLEN_MAX_BITS >> 3)
+#define QSPI_WLEN_MASK			QSPI_WLEN(QSPI_WLEN_MAX_BITS)
 /* clock control */
 #define QSPI_CLK_EN                     BIT(31)
 #define QSPI_CLK_DIV_MAX                0xffff
@@ -223,20 +226,34 @@ static int __ti_qspi_xfer(struct ti_qspi_priv *priv, unsigned int bitlen,
 		priv->cmd |= QSPI_3_PIN;
 	priv->cmd |= 0xfff;
 
-/* FIXME: This delay is required for successfull
- * completion of read/write/erase. Once its root
- * caused, it will be remove from the driver.
- */
-#ifdef CONFIG_AM43XX
-	udelay(100);
-#endif
-	while (words--) {
+	while (words) {
+		u8 xfer_len = 0;
+
 		if (txp) {
-			debug("tx cmd %08x dc %08x data %02x\n",
-			      priv->cmd | QSPI_WR_SNGL, priv->dc, *txp);
-			writel(*txp++, &priv->base->data);
-			writel(priv->cmd | QSPI_WR_SNGL,
-			       &priv->base->cmd);
+			u32 cmd = priv->cmd;
+
+			if (words >= QSPI_WLEN_MAX_BYTES) {
+				u32 *txbuf = (u32 *)txp;
+				u32 data;
+
+				data = cpu_to_be32(*txbuf++);
+				writel(data, &priv->base->data3);
+				data = cpu_to_be32(*txbuf++);
+				writel(data, &priv->base->data2);
+				data = cpu_to_be32(*txbuf++);
+				writel(data, &priv->base->data1);
+				data = cpu_to_be32(*txbuf++);
+				writel(data, &priv->base->data);
+				cmd &= ~QSPI_WLEN_MASK;
+				cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS);
+				xfer_len = QSPI_WLEN_MAX_BYTES;
+			} else {
+				writeb(*txp, &priv->base->data);
+				xfer_len = 1;
+			}
+			debug("tx cmd %08x dc %08x\n",
+			      cmd | QSPI_WR_SNGL, priv->dc);
+			writel(cmd | QSPI_WR_SNGL, &priv->base->cmd);
 			status = readl(&priv->base->status);
 			timeout = QSPI_TIMEOUT;
 			while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) {
@@ -246,6 +263,7 @@ static int __ti_qspi_xfer(struct ti_qspi_priv *priv, unsigned int bitlen,
 				}
 				status = readl(&priv->base->status);
 			}
+			txp += xfer_len;
 			debug("tx done, status %08x\n", status);
 		}
 		if (rxp) {
@@ -262,9 +280,11 @@ static int __ti_qspi_xfer(struct ti_qspi_priv *priv, unsigned int bitlen,
 				status = readl(&priv->base->status);
 			}
 			*rxp++ = readl(&priv->base->data);
+			xfer_len = 1;
 			debug("rx done, status %08x, read %02x\n",
 			      status, *(rxp-1));
 		}
+		words -= xfer_len;
 	}
 
 	/* Terminate frame */
@@ -336,7 +356,7 @@ static void ti_spi_setup_spi_register(struct ti_qspi_priv *priv)
 			QSPI_SETUP0_NUM_D_BYTES_8_BITS |
 			QSPI_SETUP0_READ_QUAD | QSPI_CMD_WRITE |
 			QSPI_NUM_DUMMY_BITS);
-	slave->mode_rx = SPI_RX_QUAD;
+	slave->mode |= SPI_RX_QUAD;
 #else
 	memval |= QSPI_CMD_READ | QSPI_SETUP0_NUM_A_BYTES |
 			QSPI_SETUP0_NUM_D_BYTES_NO_BITS |
@@ -422,7 +442,7 @@ static void __ti_qspi_setup_memorymap(struct ti_qspi_priv *priv,
 				      bool enable)
 {
 	u32 memval;
-	u32 mode = slave->mode_rx & (SPI_RX_QUAD | SPI_RX_DUAL);
+	u32 mode = slave->mode & (SPI_RX_QUAD | SPI_RX_DUAL);
 
 	if (!enable) {
 		writel(0, &priv->base->setup0);
@@ -436,7 +456,7 @@ static void __ti_qspi_setup_memorymap(struct ti_qspi_priv *priv,
 		memval |= QSPI_CMD_READ_QUAD;
 		memval |= QSPI_SETUP0_NUM_D_BYTES_8_BITS;
 		memval |= QSPI_SETUP0_READ_QUAD;
-		slave->mode_rx = SPI_RX_QUAD;
+		slave->mode |= SPI_RX_QUAD;
 		break;
 	case SPI_RX_DUAL:
 		memval |= QSPI_CMD_READ_DUAL;
diff --git a/drivers/spi/zynq_spi.c b/drivers/spi/zynq_spi.c
index 7a176a2cd6..15ca271ea4 100644
--- a/drivers/spi/zynq_spi.c
+++ b/drivers/spi/zynq_spi.c
@@ -233,7 +233,7 @@ static int zynq_spi_xfer(struct udevice *dev, unsigned int bitlen,
 
 		/* Read the data from RX FIFO */
 		status = readl(&regs->isr);
-		while (status & ZYNQ_SPI_IXR_RXNEMPTY_MASK) {
+		while ((status & ZYNQ_SPI_IXR_RXNEMPTY_MASK) && rx_len) {
 			buf = readl(&regs->rxdr);
 			if (rx_buf)
 				*rx_buf++ = buf;