summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
authorWolfgang Denk <wd@denx.de>2010-03-24 12:19:19 +0100
committerWolfgang Denk <wd@denx.de>2010-03-28 00:18:58 +0100
commita574cff121b1479c8e962b7a2a29310020387260 (patch)
tree4b937e40a968fcba986fd351b7acbb4528a89953 /doc
parentcc3074c322bd8023cbebe475e4e4e413b1c06da3 (diff)
ml300: remove support for broken, orphaned board
The ml300 board has a number of issues, but nobody cares about this long-orphaned board any more. Remove it. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Michal Simek <monstr@monstr.eu>
Diffstat (limited to 'doc')
-rw-r--r--doc/README.ml300128
1 files changed, 0 insertions, 128 deletions
diff --git a/doc/README.ml300 b/doc/README.ml300
deleted file mode 100644
index 27c5b927836..00000000000
--- a/doc/README.ml300
+++ /dev/null
@@ -1,128 +0,0 @@
-Xilinx ML300 platform
-=====================
-
-0. Introduction
----------------
-
-The Xilinx ML300 board is based on the Virtex-II Pro FPGA with
-integrated AMCC PowerPC 405 core. The board is normally booted from
-System ACE CF. U-Boot is then run out of main memory.
-
-An FPGA is a configurable and thus very flexible device. To
-accommodate for this flexibility this port of U-Boot includes the
-required means to regenerate the drivers and configuration files if
-you decide to change the hardware design. The required steps are
-described below.
-
-
-1. Requirements
----------------
-
-To compile and run U-Boot on the Xilinx ML300 platform you need the
-following items.
-
-- A Xilinx ML300 platform (see http://www.xilinx.com/ml300)
-- EDK and ISE development tools (shipping with ML300)
-- Parallel4 cable (shipping with ML300)
-- The EDK reference design for ML300. You can get this as design #6 from
- http://www.xilinx.com/ise/embedded/edk_examples.htm
-- A BOOTP/TFTP server
-
-
-2. Quick Start
---------------
-
-To compile and run U-Boot on ML300 follow the steps below. Make sure
-to consult the documentation for U-Boot, EDK, and the EDK reference
-design for ML300 if you have any questions.
-
-1. Implement the EDK reference design for ML300. You can use any of
- the project files, for example from a xygwin shell:
- $ xps -nw system_linux.xmp
- XPS% run init_bram
-2. Configure and compile U-Boot. Change into the root directory of
- U-Boot and run:
- $ export CROSS_COMPILE=powerpc-eabi-
- $ make ml300_config
- $ make
-3. Set up the ML300, connect the Parallel4 and the serial cable. Start
- a terminal on your host computer and set the communication
- parameters to 9600,8N1,no handshake.
-4. Set up the BOOTP/TFTP server on your host machine. U-Boot is
- preconfigured to use a fixed HW MAC address of 00:0A:35:00:22:01.
-5. Download the bitstream to the ML300.
-6. Use XMD to download and run U-Boot on the ML300:
- $ xmd
- XMD% ppcconnect
- XMD% dow u-boot
- XMD% run
-
-You can now make an ACE file out of bitstream and U-Boot:
- $ xmd genace.tcl -jprog -board ml300 -hw \
- implementation/download.bit -elf u-boot -ace top.ace
-
-Put the ACE file onto the MicroDrive, for example into xilinx/myace,
-and reboot ML300.
-
-
-3. Generating a Custom BSP for U-Boot
--------------------------------------
-
-If you decide to change the EDK reference design for ML300 or if you
-build a new design from scratch either with the Base System Builder in
-XPS or all by hand you most likely will change the base addresses for
-the Uart and the Ethernet peripheral. If you do so you will have two
-options:
-
-1. Edit boards/xilinx/ml300/xparameters.h to reflect the changes you
- made to your hardware.
-2. Use the MLD technology provided by Xilinx Platform Studio to make
- the changes automatically. To do so go to the root directory of the
- EDK reference design for ML300. Copy the Linux project file and the
- Linux software configuration file:
- $ cp system_linux.xmp system_uboot.xmp
- $ cp system_linux.mss system_uboot.mss
-
- Edit system_uboot.xmp and and have it point to system_uboot.mss for
- the software configuration.
-
- Then, copy the sw_services directory in
- boards/xilinx/ml300/sw_services to the root directory of the EDK
- reference design for ML300.
- $ cp -R <uboot dir>/boards/xilinx/ml300/sw_services <edk dir>
-
- Modify system_uboot.mss. Look for the Linux library definition
- and change it to generate a BSP for U-Boot. An example, might look
- like this:
-
- BEGIN LIBRARY
- PARAMETER LIBRARY_NAME = uboot
- PARAMETER LIBRARY_VER = 1.00.a
- PARAMETER CONNECTED_PERIPHS = (opb_uart16550_0,opb_ethernet_0)
- PARAMETER TARGET_DIR = <uboot dir>
- END
-
- Now, you are ready to generate the Xilinx ML300 BSP for U-Boot:
- $ xps -nw system_uboot.xmp
- XPS% run libs
-
- If all goes well the new configuration has been copied into the
- right places within the U-Boot source tree. Recompile U-Boot and
- run it on the ML300.
-
-
-4. ToDo
--------
-
-- Add support for all other peripherals on ML300.
-- Read the MAC address out of the IIC EEPROM.
-- Store the bootargs in the IIC EEPROM.
-
-
-5. References
--------------
-
-ML300: http://www.xilinx.com/ml300
-EDK: http://www.xilinx.com/edk
-ISE: http://www.xilinx.com/ise
-Reference Design: http://www.xilinx.com/ise/embedded/edk_examples.htm