summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
authorWolfgang Denk <wd@denx.de>2012-04-16 23:13:51 +0200
committerWolfgang Denk <wd@denx.de>2012-04-16 23:13:51 +0200
commitf5cdc11775c4b7fdbf52a6dd2f463d329804ab11 (patch)
tree362ae60b8776090a35f2abfa7e9a8e37a0150377 /doc
parentdb39f24151627733d6166c5e9a875fe8b356fa72 (diff)
Prepare v2012.04-rc2; minor Coding Style cleanupv2012.04-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
Diffstat (limited to 'doc')
-rw-r--r--doc/README.sbc854828
-rw-r--r--doc/device-tree-bindings/i2c/tegra20-i2c.txt4
2 files changed, 16 insertions, 16 deletions
diff --git a/doc/README.sbc8548 b/doc/README.sbc8548
index 0f3f5432f26..feac5e3e63e 100644
--- a/doc/README.sbc8548
+++ b/doc/README.sbc8548
@@ -23,7 +23,7 @@ of each choice are listed below.
Choice #1 does not enable CONFIG_PCI, and assumes that the PCI slot
will be left empty (M66EN high), and so the board will operate with
-a base clock of 66MHz. Note that you need both PCI enabled in u-boot
+a base clock of 66MHz. Note that you need both PCI enabled in u-boot
and linux in order to have functional PCI under linux.
The second enables PCI support and builds for a 33MHz clock rate. Note
@@ -37,29 +37,29 @@ card. [The above discussion assumes that the SW2[1-4] has not been changed
to reflect a different CCB:SYSCLK ratio]
The third option builds PCI support in, and leaves the clocking at the
-default 66MHz. Options four and five are just repeats of option two
+default 66MHz. Options four and five are just repeats of option two
and three, but with PCI-e support enabled as well.
PCI output listing with an intel e1000 PCI-x and a Syskonnect SK-9Exx
-is shown below for sbc8548_PCI_66_PCIE_config. (Note that PCI-e with
+is shown below for sbc8548_PCI_66_PCIE_config. (Note that PCI-e with
a 33MHz PCI configuration is currently untested.)
=> pci 0
Scanning PCI devices on bus 0
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 00.00.00 0x1057 0x0012 Processor 0x20
- 00.01.00 0x8086 0x1026 Network controller 0x00
+ 00.00.00 0x1057 0x0012 Processor 0x20
+ 00.01.00 0x8086 0x1026 Network controller 0x00
=> pci 1
Scanning PCI devices on bus 1
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 01.00.00 0x1957 0x0012 Processor 0x20
+ 01.00.00 0x1957 0x0012 Processor 0x20
=> pci 2
Scanning PCI devices on bus 2
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 02.00.00 0x1148 0x9e00 Network controller 0x00
+ 02.00.00 0x1148 0x9e00 Network controller 0x00
=>
Memory Size and using SPD:
@@ -80,10 +80,10 @@ You can also visually inspect the board to see if this hardware
fix has been applied:
1) Remove R314 (RES-R0174-033, 1K, 0603). R314 is located on
- the back of the PCB behind the DDR SDRAM SODIMM connector.
+ the back of the PCB behind the DDR SDRAM SODIMM connector.
2) Solder RES-R0174-033 (1K, 0603) resistor from R314 pin 2 pad
- to R313 pin 2. Pin 2 for each resistor is the end of the
- resistor closest to the CPU.
+ to R313 pin 2. Pin 2 for each resistor is the end of the
+ resistor closest to the CPU.
Boards without the mod will have R314 and R313 in parallel, like "||".
After the mod, they will be touching and form an "L" shape.
@@ -155,7 +155,7 @@ Hardware Reference:
===================
The following contains some summary information on hardware settings
-that are relevant to u-boot, based on the board manual. For the
+that are relevant to u-boot, based on the board manual. For the
most up to date and complete details of the board, please request the
reference manual ERG-00327-001.pdf from www.windriver.com
diff --git a/doc/device-tree-bindings/i2c/tegra20-i2c.txt b/doc/device-tree-bindings/i2c/tegra20-i2c.txt
index d601c17f9b1..72649dffa38 100644
--- a/doc/device-tree-bindings/i2c/tegra20-i2c.txt
+++ b/doc/device-tree-bindings/i2c/tegra20-i2c.txt
@@ -4,10 +4,10 @@ Added in U-Boot:
Required properties:
- clocks : Two clocks must be given, each as a phandle to the Tegra's
- CAR node and the clock number as a parameter:
+ CAR node and the clock number as a parameter:
- the I2C clock to use for the peripheral
- the pll_p_out3 clock, which can be used for fast operation. This
- does not change and is the same for all I2C nodes.
+ does not change and is the same for all I2C nodes.
Example:
(TODO: merge with existing example):