summaryrefslogtreecommitdiff
path: root/doc/README.zeus
diff options
context:
space:
mode:
authorStefan Roese <sr@denx.de>2007-08-14 14:44:41 +0200
committerStefan Roese <sr@denx.de>2007-08-14 14:44:41 +0200
commit779e975117a75e91fcebe226a63104dbfb924ab1 (patch)
tree42f48ba97342287f8e155cce29e8e0600064a16f /doc/README.zeus
parentc5a172a5fd636c12467429e3f7910e53773979c6 (diff)
ppc4xx: Add initial Zeus (PPC405EP) board support
Signed-off-by: Stefan Roese <sr@denx.de>
Diffstat (limited to 'doc/README.zeus')
-rw-r--r--doc/README.zeus73
1 files changed, 73 insertions, 0 deletions
diff --git a/doc/README.zeus b/doc/README.zeus
new file mode 100644
index 00000000000..1848d8cd384
--- /dev/null
+++ b/doc/README.zeus
@@ -0,0 +1,73 @@
+
+Storage of the board specific values (ethaddr...)
+-------------------------------------------------
+
+The board specific environment variables that should be unique
+for each individual board, can be stored in the I2C EEPROM. This
+will be done from offset 0x80 with the length of 0x80 bytes. The
+following command can be used to store the values here:
+
+=> setdef de:20:6a:ed:e2:72 de:20:6a:ed:e2:73 AB0001
+
+ ethaddr eth1addr serial#
+
+Now those 3 values are stored into the I2C EEPROM. A CRC is added
+to make sure that the values get not corrupted.
+
+
+SW-Reset Pushbutton handling:
+-----------------------------
+
+The SW-reset push button is connected to a GPIO input too. This
+way U-Boot can "see" how long the SW-reset was pressed, and a
+specific action can be taken. Two different actions are supported:
+
+a) Release after more than 5 seconds and less then 10 seconds:
+ -> Run POST
+
+ Please note, that the POST test will take a while (approx. 1 min
+ on the 128MByte board). This is mainly due to the system memory
+ test.
+
+b) Release after more than 10 seconds:
+ -> Restore factory default settings
+
+ The factory default values are restored. The default environment
+ variables are restored (ipaddr, serverip...) and the board
+ specific values (ethaddr, eth1addr and serial#) are restored
+ to the environment from the I2C EEPROM. Also a bootline parameter
+ is added to the Linux bootline to signal the Linux kernel upon
+ the next startup, that the factory defaults should be restored.
+
+The command to check this sw-reset status and act accordingly is
+
+=> chkreset
+
+This command is added to the default "bootcmd", so that it is called
+automatically upon startup.
+
+Also, the 2 LED's are used to indicate the current status of this
+command (time passed since pushing the button). When the POST test
+will be run, the green LED will be switched off, and when the
+factory restore will be initiated, the reg LED will be switched off.
+
+
+Loggin of POST results:
+-----------------------
+
+The results of the POST tests are logged in a logbuffer located at the end
+of the onboard memory. It can be accessed with the U-Boot command "log":
+
+=> log show
+<4>POST memory PASSED
+<4>POST cache PASSED
+<4>POST cpu PASSED
+<4>POST uart PASSED
+<4>POST ethernet PASSED
+
+The DENX Linux kernel tree has support for this log buffer included. Exactly
+this buffer is used for logging of all kernel messages too. By enabling the
+compile time option "CONFIG_LOGBUFFER" this support is enabled. This way you
+can access the U-Boot log messages from Linux too.
+
+2007-08-10, Stefan Roese <sr@denx.de>