doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 99 deletions

diff --git a/doc/README.ocotea-PIBS-to-U-Boot b/doc/README.ocotea-PIBS-to-U-Boot
deleted file mode 100644
index 25dd2a23781..00000000000
--- a/doc/README.ocotea-PIBS-to-U-Boot
+++ /dev/null
@@ -1,99 +0,0 @@
-------------------------------------------
-Installation of U-Boot using PIBS firmware
-------------------------------------------
-
-This document describes how to install U-Boot on the Ocotea PPC440GX
-Evaluation Board. We do not erase the PIBS firmware but install U-Boot in the
-soldered FLASH. After this you should be able to switch between PIBS and
-U-Boot via the switch U46 SW1. Please check that SW1 is off (= open) before
-continuing.
-
-Connect to the serial port 0 (J11 lower) of the Ocotea board using the cu
-program. See the hints for configuring cu above. Make sure you can
-communicate with the PIBS firmware: reset the board and hit ENTER a couple of
-times until you see the PIBS prompt (PIBS $). Then proceed as follows:
-
-
-Read MAC Addresses from PIBS
-----------------------------
-
-To read the configured MAC addresses available on your Ocotea board please use
-the following commands:
-
-PIBS $ echo $hwdaddr0
-000173017FE3
-PIBS $ echo $hwdaddr1
-000173017FE4
-PIBS $ echo $hwdaddr2
-000173017FE1
-PIBS $ echo $hwdaddr3
-000173017FE2
-
-In U-Boot this is stored in the following environment variables:
-
-* Ethernet Address 0: ethaddr = 000173017FE3 (==> 00:01:73:01:7F:E3)
-* Ethernet Address 1: eth1addr = 000173017FE4 (==> 00:01:73:01:7F:E4)
-* Ethernet Address 2: eth2addr = 000173017FE1 (==> 00:01:73:01:7F:E1)
-* Ethernet Address 3: eth3addr = 000173017FE2 (==> 00:01:73:01:7F:E2)
-
-
-Configure the network interface (ent0 == emac0)
------------------------------------------------
-
-To download the U-Boot image we need to configure the ethernet interface with
-the following commands:
-
-PIBS $ ifconfig ent0 192.168.160.142 netmask 255.255.0.0 up
-PIBS $ set ipdstaddr0=192.168.1.1
-status: writing PIBS variable value to FLASH
-PIBS $ set bootfilename=/tftpboot/ocotea/u-boot.bin
-status: writing PIBS variable value to FLASH
-
-Please insert correct parameters for your configuration (ip-addresses and
-file-location).
-
-
-Program U-Boot into soldered User-FLASH
----------------------------------------
-
-Please make sure to use a newer version of U-Boot (at least 1.1.3), since
-older versions don't support running from user-FLASH.
-
-To program U-Boot into the soldered user-FLASH use the following command:
-
-PIBS $ storefile bin eth 0xffbc0000
-
-This commands loads the file vis ethernet into ram and copies it into the
-user-FLASH.
-
-
-Switch to U-Boot
-----------------
-
-Now you can turn your board off and switch SW1 (U46) to on (= closed). After
-powering the board you should see the following message:
-
-U-Boot 1.1.3 (Apr  5 2005 - 22:59:57)
-
-AMCC PowerPC 440 GX Rev. C
-Board: AMCC 440GX Evaluation Board
-	VCO: 1066 MHz
-	CPU: 533 MHz
-	PLB: 152 MHz
-	OPB: 76 MHz
-	EPB: 76 MHz
-I2C:   ready
-DRAM:  256 MB
-FLASH:	5 MB
-PCI:   Bus Dev VenId DevId Class Int
-In:    serial
-Out:   serial
-Err:   serial
-KGDB:  kgdb ready
-ready
-Net:   ppc_440x_eth0, ppc_440x_eth1, ppc_440x_eth2, ppc_440x_eth3
-BEDBUG:ready
-=>
-
-
-April 06 2005, Stefan Roese <sr@denx.de>