doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 111 deletions

diff --git a/doc/README.mpc8313erdb b/doc/README.mpc8313erdb
deleted file mode 100644
index be7ef32b45..0000000000
--- a/doc/README.mpc8313erdb
+++ /dev/null
@@ -1,111 +0,0 @@
-Freescale MPC8313ERDB Board
------------------------------------------
-
-1.	Board Switches and Jumpers
-
-	S3 is used to set CONFIG_SYS_RESET_SOURCE.
-
-	To boot the image at 0xFE000000 in NOR flash, use these DIP
-	switch settings for S3 S4:
-
-	+------+	+------+
-	|      |	| **** |
-	| **** |	|      |
-	+------+ ON	+------+ ON
-	  4321		  4321
-	(where the '*' indicates the position of the tab of the switch.)
-
-	To boot the image at the beginning of NAND flash, use these
-	DIP switch settings for S3 S4:
-
-	+------+	+------+
-	| *    |	|  *** |
-	|  *** |	| *    |
-	+------+ ON	+------+ ON
-	  4321		  4321
-	(where the '*' indicates the position of the tab of the switch.)
-
-	When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
-
-2.	Memory Map
-	The memory map looks like this:
-
-	0x0000_0000	0x07ff_ffff	DDR		 128M
-	0x8000_0000	0x8fff_ffff	PCI MEM		 256M
-	0x9000_0000	0x9fff_ffff	PCI_MMIO	 256M
-	0xe000_0000	0xe00f_ffff	IMMR		 1M
-	0xe200_0000	0xe20f_ffff	PCI IO		 16M
-	0xe280_0000	0xe280_7fff	NAND FLASH (CS1) 32K
-	0xf000_0000	0xf001_ffff	VSC7385 (CS2)	 128K
-	0xfa00_0000	0xfa00_7fff	Board Status/	 32K
-					LED Control (CS3)
-	0xfe00_0000	0xfe7f_ffff	NOR FLASH (CS0)	 8M
-
-	When booting from NAND, NAND flash is CS0 and NOR flash
-	is CS1.
-
-3.	Definitions
-
-3.1	Explanation of NEW definitions in:
-
-	include/configs/MPC8313ERDB.h
-
-	CONFIG_MPC83xx		MPC83xx family
-	CONFIG_MPC831x		MPC831x specific
-	CONFIG_MPC8313ERDB	MPC8313ERDB board specific
-
-4.	Compilation
-
-	Assuming you're using BASH (or similar) as your shell:
-
-	export CROSS_COMPILE=your-cross-compiler-prefix-
-	make distclean
-	make MPC8313ERDB_XXX_config
-	(where XXX is:
-	   33 - 33 MHz oscillator, boot from NOR flash
-	   66 - 66 MHz oscillator, boot from NOR flash
-	   NAND_33 - 33 MHz oscillator, boot from NAND flash
-	   NAND_66 - 66 MHz oscillator, boot from NAND flash)
-	make
-
-5.	Downloading and Flashing Images
-
-5.1	Reflash U-boot Image using U-boot
-
-	NOR flash:
-
-	=>run tftpflash
-
-	You may want to try
-	=>tftpboot $loadaddr $uboot
-	first, to make sure that the TFTP load will succeed before it
-	goes ahead and wipes out your current firmware.  And of course,
-	have an alternate means of programming the flash available
-	if the new u-boot doesn't boot.
-
-	NAND flash:
-
-	=>tftpboot $loadaddr <filename>
-	=>nand erase 0 0x80000
-	=>nand write $loadaddr 0 0x80000
-
-	...where 0x80000 is the filesize rounded up to
-	the next 0x20000 increment.
-
-5.2	Downloading and Booting Linux Kernel
-
-	Ensure that all networking-related environment variables are set
-	properly (including ipaddr, serverip, gatewayip (if needed),
-	netmask, ethaddr, eth1addr, rootpath (if using NFS root),
-	fdtfile, and bootfile).
-
-	Then, do one of the following, depending on whether you
-	want an NFS root or a ramdisk root:
-
-	=>run nfsboot
-	or
-	=>run ramboot
-
-6	Notes
-
-	The console baudrate for MPC8313ERDB is 115200bps.