powerpc: mpc5xxx: remove BC3450 board support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

6 files changed, 0 insertions, 1432 deletions

diff --git a/board/bc3450/Kconfig b/board/bc3450/Kconfig
deleted file mode 100644
index a0fc19f63c1..00000000000
--- a/board/bc3450/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_BC3450
-
-config SYS_BOARD
-	default "bc3450"
-
-config SYS_CONFIG_NAME
-	default "BC3450"
-
-endif
diff --git a/board/bc3450/MAINTAINERS b/board/bc3450/MAINTAINERS
deleted file mode 100644
index 81a70760931..00000000000
--- a/board/bc3450/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-BC3450 BOARD
-#M:	-
-S:	Maintained
-F:	board/bc3450/
-F:	include/configs/BC3450.h
-F:	configs/BC3450_defconfig
diff --git a/board/bc3450/Makefile b/board/bc3450/Makefile
deleted file mode 100644
index b8d22bafed8..00000000000
--- a/board/bc3450/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= bc3450.o cmd_bc3450.o
diff --git a/board/bc3450/bc3450.c b/board/bc3450/bc3450.c
deleted file mode 100644
index a5c6d750cb2..00000000000
--- a/board/bc3450/bc3450.c
+++ /dev/null
@@ -1,586 +0,0 @@
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * (C) Copyright 2004-2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * (C) Copyright 2006
- * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <netdev.h>
-
-#ifdef CONFIG_VIDEO_SM501
-#include <sm501.h>
-#endif
-
-#if defined(CONFIG_MPC5200_DDR)
-#include "mt46v16m16-75.h"
-#else
-#include "mt48lc16m16a2-75.h"
-#endif
-
-#ifdef CONFIG_RTC_MPC5200
-#include <rtc.h>
-#endif
-
-#ifdef CONFIG_PS2MULT
-void ps2mult_early_init(void);
-#endif
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start (int hi_addr)
-{
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
-	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
-		hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
-		hi_addr_bit;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set mode register: extended mode */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
-	__asm__ volatile ("sync");
-
-	/* set mode register: reset DLL */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
-	__asm__ volatile ("sync");
-#endif
-
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
-		hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
-		hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
-	__asm__ volatile ("sync");
-
-	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
-	__asm__ volatile ("sync");
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- *	      use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- *	      is something else than 0x00000000.
- */
-
-phys_size_t initdram (int board_type)
-{
-	ulong dramsize = 0;
-	ulong dramsize2 = 0;
-#ifndef CONFIG_SYS_RAMBOOT
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x40000000; /* disabled */
-	__asm__ volatile ("sync");
-
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set tap delay */
-	*(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
-	__asm__ volatile ("sync");
-#endif
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else {
-		dramsize = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20)) {
-		dramsize = 0;
-	}
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0) {
-		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
-			__builtin_ffs(dramsize >> 20) - 1;
-	} else {
-		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
-	}
-
-	/* let SDRAM CS1 start right after CS0 */
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001c; /* 512MB */
-
-	/* find RAM size using SDRAM CS1 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize2 = test1;
-	} else {
-		dramsize2 = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize2 < (1 << 20)) {
-		dramsize2 = 0;
-	}
-
-	/* set SDRAM CS1 size according to the amount of RAM found */
-	if (dramsize2 > 0) {
-		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
-			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-	} else {
-		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-	}
-
-#else /* CONFIG_SYS_RAMBOOT */
-
-	/* retrieve size of memory connected to SDRAM CS0 */
-	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
-	if (dramsize >= 0x13) {
-		dramsize = (1 << (dramsize - 0x13)) << 20;
-	} else {
-		dramsize = 0;
-	}
-
-	/* retrieve size of memory connected to SDRAM CS1 */
-	dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
-	if (dramsize2 >= 0x13) {
-		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
-	} else {
-		dramsize2 = 0;
-	}
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-	return dramsize;
-}
-
-int checkboard (void)
-{
-#if defined (CONFIG_TQM5200)
-	puts ("Board: TQM5200 (TQ-Components GmbH)\n");
-#endif
-
-#if defined (CONFIG_BC3450)
-	puts ("Dev:   GERSYS BC3450\n");
-#endif
-
-	return 0;
-}
-
-void flash_preinit(void)
-{
-	/*
-	 * Now, when we are in RAM, enable flash write
-	 * access for detection process.
-	 * Note that CS_BOOT cannot be cleared when
-	 * executing in flash.
-	 */
-	*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1;		/* clear RO	   */
-}
-
-
-#ifdef	CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
-	pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
-	debug ("init_ide_reset\n");
-
-	/* Configure PSC1_4 as GPIO output for ATA reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
-}
-
-void ide_set_reset (int idereset)
-{
-	debug ("ide_reset(%d)\n", idereset);
-
-	if (idereset) {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
-	} else {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |=  GPIO_PSC1_4;
-	}
-}
-#endif
-
-#ifdef CONFIG_POST
-/*
- * Reads GPIO pin PSC6_3. A keypress is reported, if PSC6_3 is low. If PSC6_3
- * is left open, no keypress is detected.
- */
-int post_hotkeys_pressed(void)
-{
-	struct mpc5xxx_gpio *gpio;
-
-	gpio = (struct mpc5xxx_gpio*) MPC5XXX_GPIO;
-
-	/*
-	 * Configure PSC6_1 and PSC6_3 as GPIO. PSC6 then couldn't be used in
-	 * CODEC or UART mode. Consumer IrDA should still be possible.
-	 */
-	gpio->port_config &= ~(0x07000000);
-	gpio->port_config |=   0x03000000;
-
-	/* Enable GPIO for GPIO_IRDA_1 (IR_USB_CLK pin) = PSC6_3 */
-	gpio->simple_gpioe |= 0x20000000;
-
-	/* Configure GPIO_IRDA_1 as input */
-	gpio->simple_ddr &= ~(0x20000000);
-
-	return ((gpio->simple_ival & 0x20000000) ? 0 : 1);
-}
-#endif
-
-#ifdef CONFIG_BOARD_EARLY_INIT_R
-int board_early_init_r (void)
-{
-#ifdef CONFIG_RTC_MPC5200
-	struct rtc_time t;
-
-	/* set to Wed Dec 31 19:00:00 1969 */
-	t.tm_sec = t.tm_min = 0;
-	t.tm_hour = 19;
-	t.tm_mday = 31;
-	t.tm_mon = 12;
-	t.tm_year = 1969;
-	t.tm_wday = 3;
-
-	rtc_set(&t);
-#endif /* CONFIG_RTC_MPC5200 */
-
-#ifdef CONFIG_PS2MULT
-	ps2mult_early_init();
-#endif /* CONFIG_PS2MULT */
-	return (0);
-}
-#endif /* CONFIG_BOARD_EARLY_INIT_R */
-
-
-int last_stage_init (void)
-{
-	/*
-	 * auto scan for really existing devices and re-set chip select
-	 * configuration.
-	 */
-	u16 save, tmp;
-	int restore;
-
-	/*
-	 * Check for SRAM and SRAM size
-	 */
-
-	/* save original SRAM content  */
-	save = *(volatile u16 *)CONFIG_SYS_CS2_START;
-	restore = 1;
-
-	/* write test pattern to SRAM */
-	*(volatile u16 *)CONFIG_SYS_CS2_START = 0xA5A5;
-	__asm__ volatile ("sync");
-	/*
-	 * Put a different pattern on the data lines: otherwise they may float
-	 * long enough to read back what we wrote.
-	 */
-	tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
-	if (tmp == 0xA5A5)
-		puts ("!! possible error in SRAM detection\n");
-
-	if (*(volatile u16 *)CONFIG_SYS_CS2_START != 0xA5A5) {
-		/* no SRAM at all, disable cs */
-		*(vu_long *)MPC5XXX_ADDECR &= ~(1 << 18);
-		*(vu_long *)MPC5XXX_CS2_START = 0x0000FFFF;
-		*(vu_long *)MPC5XXX_CS2_STOP = 0x0000FFFF;
-		restore = 0;
-		__asm__ volatile ("sync");
-	} else if (*(volatile u16 *)(CONFIG_SYS_CS2_START + (1<<19)) == 0xA5A5) {
-		/* make sure that we access a mirrored address */
-		*(volatile u16 *)CONFIG_SYS_CS2_START = 0x1111;
-		__asm__ volatile ("sync");
-		if (*(volatile u16 *)(CONFIG_SYS_CS2_START + (1<<19)) == 0x1111) {
-			/* SRAM size = 512 kByte */
-			*(vu_long *)MPC5XXX_CS2_STOP = STOP_REG(CONFIG_SYS_CS2_START,
-								0x80000);
-			__asm__ volatile ("sync");
-			puts ("SRAM:  512 kB\n");
-		}
-		else
-			puts ("!! possible error in SRAM detection\n");
-	} else {
-		puts ("SRAM:  1 MB\n");
-	}
-	/* restore origianl SRAM content  */
-	if (restore) {
-		*(volatile u16 *)CONFIG_SYS_CS2_START = save;
-		__asm__ volatile ("sync");
-	}
-
-	/*
-	 * Check for Grafic Controller
-	 */
-
-	/* save origianl FB content  */
-	save = *(volatile u16 *)CONFIG_SYS_CS1_START;
-	restore = 1;
-
-	/* write test pattern to FB memory */
-	*(volatile u16 *)CONFIG_SYS_CS1_START = 0xA5A5;
-	__asm__ volatile ("sync");
-	/*
-	 * Put a different pattern on the data lines: otherwise they may float
-	 * long enough to read back what we wrote.
-	 */
-	tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
-	if (tmp == 0xA5A5)
-		puts ("!! possible error in grafic controller detection\n");
-
-	if (*(volatile u16 *)CONFIG_SYS_CS1_START != 0xA5A5) {
-		/* no grafic controller at all, disable cs */
-		*(vu_long *)MPC5XXX_ADDECR &= ~(1 << 17);
-		*(vu_long *)MPC5XXX_CS1_START = 0x0000FFFF;
-		*(vu_long *)MPC5XXX_CS1_STOP = 0x0000FFFF;
-		restore = 0;
-		__asm__ volatile ("sync");
-	} else {
-		puts ("VGA:   SMI501 (Voyager) with 8 MB\n");
-	}
-	/* restore origianl FB content	*/
-	if (restore) {
-		*(volatile u16 *)CONFIG_SYS_CS1_START = save;
-		__asm__ volatile ("sync");
-	}
-
-	return 0;
-}
-
-#ifdef CONFIG_VIDEO_SM501
-
-#define DISPLAY_WIDTH	640
-#define DISPLAY_HEIGHT	480
-
-#ifdef CONFIG_VIDEO_SM501_8BPP
-#error CONFIG_VIDEO_SM501_8BPP not supported.
-#endif /* CONFIG_VIDEO_SM501_8BPP */
-
-#ifdef CONFIG_VIDEO_SM501_16BPP
-#error CONFIG_VIDEO_SM501_16BPP not supported.
-#endif /* CONFIG_VIDEO_SM501_16BPP */
-
-#ifdef CONFIG_VIDEO_SM501_32BPP
-static const SMI_REGS init_regs [] =
-{
-#if defined (CONFIG_BC3450_FP) && !defined (CONFIG_BC3450_CRT)
-	/* FP only */
-	{0x00004, 0x0},
-	{0x00048, 0x00021807},
-	{0x0004C, 0x091a0a01},
-	{0x00054, 0x1},
-	{0x00040, 0x00021807},
-	{0x00044, 0x091a0a01},
-	{0x00054, 0x0},
-	{0x80000, 0x01013106},
-	{0x80004, 0xc428bb17},
-	{0x80000, 0x03013106},
-	{0x8000C, 0x00000000},
-	{0x80010, 0x0a000a00},
-	{0x80014, 0x02800000},
-	{0x80018, 0x01e00000},
-	{0x8001C, 0x00000000},
-	{0x80020, 0x01e00280},
-	{0x80024, 0x02fa027f},
-	{0x80028, 0x004a028b},
-	{0x8002C, 0x020c01df},
-	{0x80030, 0x000201e9},
-	{0x80200, 0x00010200},
-	{0x80000, 0x0f013106},
-#elif defined (CONFIG_BC3450_CRT) && !defined (CONFIG_BC3450_FP)
-	/* CRT only */
-	{0x00004, 0x0},
-	{0x00048, 0x00021807},
-	{0x0004C, 0x10090a01},
-	{0x00054, 0x1},
-	{0x00040, 0x00021807},
-	{0x00044, 0x10090a01},
-	{0x00054, 0x0},
-	{0x80200, 0x00010000},
-	{0x80204, 0x0},
-	{0x80208, 0x0A000A00},
-	{0x8020C, 0x02fa027f},
-	{0x80210, 0x004a028b},
-	{0x80214, 0x020c01df},
-	{0x80218, 0x000201e9},
-	{0x80200, 0x00013306},
-#else	/* panel + CRT */
-	{0x00004, 0x0},
-	{0x00048, 0x00021807},
-	{0x0004C, 0x091a0a01},
-	{0x00054, 0x1},
-	{0x00040, 0x00021807},
-	{0x00044, 0x091a0a01},
-	{0x00054, 0x0},
-	{0x80000, 0x0f013106},
-	{0x80004, 0xc428bb17},
-	{0x8000C, 0x00000000},
-	{0x80010, 0x0a000a00},
-	{0x80014, 0x02800000},
-	{0x80018, 0x01e00000},
-	{0x8001C, 0x00000000},
-	{0x80020, 0x01e00280},
-	{0x80024, 0x02fa027f},
-	{0x80028, 0x004a028b},
-	{0x8002C, 0x020c01df},
-	{0x80030, 0x000201e9},
-	{0x80200, 0x00010000},
-#endif
-	{0, 0}
-};
-#endif /* CONFIG_VIDEO_SM501_32BPP */
-
-#ifdef CONFIG_CONSOLE_EXTRA_INFO
-/*
- * Return text to be printed besides the logo.
- */
-void video_get_info_str (int line_number, char *info)
-{
-	if (line_number == 1) {
-#if defined (CONFIG_TQM5200)
-	    strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#else
-#error No supported board selected
-#endif /* CONFIG_TQM5200 */
-
-#if defined (CONFIG_BC3450)
-	} else if (line_number == 2) {
-	    strcpy (info, " Dev:   GERSYS BC3450");
-#endif /* CONFIG_BC3450 */
-	}
-	else {
-		info [0] = '\0';
-	}
-}
-#endif
-
-/*
- * Returns SM501 register base address. First thing called in the
- * driver. Checks if SM501 is physically present.
- */
-unsigned int board_video_init (void)
-{
-	u16 save, tmp;
-	int restore, ret;
-
-	/*
-	 * Check for Grafic Controller
-	 */
-
-	/* save origianl FB content  */
-	save = *(volatile u16 *)CONFIG_SYS_CS1_START;
-	restore = 1;
-
-	/* write test pattern to FB memory */
-	*(volatile u16 *)CONFIG_SYS_CS1_START = 0xA5A5;
-	__asm__ volatile ("sync");
-	/*
-	 * Put a different pattern on the data lines: otherwise they may float
-	 * long enough to read back what we wrote.
-	 */
-	tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
-	if (tmp == 0xA5A5)
-		puts ("!! possible error in grafic controller detection\n");
-
-	if (*(volatile u16 *)CONFIG_SYS_CS1_START != 0xA5A5) {
-		/* no grafic controller found */
-		restore = 0;
-		ret = 0;
-	} else {
-	    ret = SM501_MMIO_BASE;
-	}
-
-	if (restore) {
-		*(volatile u16 *)CONFIG_SYS_CS1_START = save;
-		__asm__ volatile ("sync");
-	}
-	return ret;
-}
-
-/*
- * Returns SM501 framebuffer address
- */
-unsigned int board_video_get_fb (void)
-{
-	return SM501_FB_BASE;
-}
-
-/*
- * Called after initializing the SM501 and before clearing the screen.
- */
-void board_validate_screen (unsigned int base)
-{
-}
-
-/*
- * Return a pointer to the initialization sequence.
- */
-const SMI_REGS *board_get_regs (void)
-{
-	return init_regs;
-}
-
-int board_get_width (void)
-{
-	return DISPLAY_WIDTH;
-}
-
-int board_get_height (void)
-{
-	return DISPLAY_HEIGHT;
-}
-
-#endif /* CONFIG_VIDEO_SM501 */
-
-int board_eth_init(bd_t *bis)
-{
-	cpu_eth_init(bis); /* Built in FEC comes first */
-	return pci_eth_init(bis);
-}
diff --git a/board/bc3450/cmd_bc3450.c b/board/bc3450/cmd_bc3450.c
deleted file mode 100644
index 3c6e798ac33..00000000000
--- a/board/bc3450/cmd_bc3450.c
+++ /dev/null
@@ -1,805 +0,0 @@
-/*
- * (C) Copyright 2005
- * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de
- *
- * (C) Copyright 2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-
-/*
- * BC3450 specific commands
- */
-#if defined(CONFIG_CMD_BSP)
-
-/*
- * Definitions for DS1620 chip
- */
-#define THERM_START_CONVERT	0xee
-#define THERM_RESET		0xaf
-#define THERM_READ_CONFIG	0xac
-#define THERM_READ_TEMP		0xaa
-#define THERM_READ_TL		0xa2
-#define THERM_READ_TH		0xa1
-#define THERM_WRITE_CONFIG	0x0c
-#define THERM_WRITE_TL		0x02
-#define THERM_WRITE_TH		0x01
-
-#define CONFIG_SYS_1SHOT		1
-#define CONFIG_SYS_STANDALONE		0
-
-struct therm {
-	int hi;
-	int lo;
-};
-
-/*
- * SM501 Register
- */
-#define SM501_GPIO_CTRL_LOW		0x00000008UL	/* gpio pins 0..31  */
-#define SM501_GPIO_CTRL_HIGH		0x0000000CUL	/* gpio pins 32..63 */
-#define SM501_POWER_MODE0_GATE		0x00000040UL
-#define SM501_POWER_MODE1_GATE		0x00000048UL
-#define POWER_MODE_GATE_GPIO_PWM_I2C	0x00000040UL
-#define SM501_GPIO_DATA_LOW		0x00010000UL
-#define SM501_GPIO_DATA_HIGH		0x00010004UL
-#define SM501_GPIO_DATA_DIR_LOW		0x00010008UL
-#define SM501_GPIO_DATA_DIR_HIGH	0x0001000CUL
-#define SM501_PANEL_DISPLAY_CONTROL	0x00080000UL
-#define SM501_CRT_DISPLAY_CONTROL	0x00080200UL
-
-/* SM501 CRT Display Control Bits */
-#define SM501_CDC_SEL			(1 << 9)
-#define SM501_CDC_TE			(1 << 8)
-#define SM501_CDC_E			(1 << 2)
-
-/* SM501 Panel Display Control Bits */
-#define SM501_PDC_FPEN			(1 << 27)
-#define SM501_PDC_BIAS			(1 << 26)
-#define SM501_PDC_DATA			(1 << 25)
-#define SM501_PDC_VDDEN			(1 << 24)
-
-/* SM501 GPIO Data LOW Bits */
-#define SM501_GPIO24			0x01000000
-#define SM501_GPIO25			0x02000000
-#define SM501_GPIO26			0x04000000
-#define SM501_GPIO27			0x08000000
-#define SM501_GPIO28			0x10000000
-#define SM501_GPIO29			0x20000000
-#define SM501_GPIO30			0x40000000
-#define SM501_GPIO31			0x80000000
-
-/* SM501 GPIO Data HIGH Bits */
-#define SM501_GPIO46			0x00004000
-#define SM501_GPIO47			0x00008000
-#define SM501_GPIO48			0x00010000
-#define SM501_GPIO49			0x00020000
-#define SM501_GPIO50			0x00040000
-#define SM501_GPIO51			0x00080000
-
-/* BC3450 GPIOs @ SM501 Data LOW */
-#define DIP				(SM501_GPIO24 | SM501_GPIO25 | SM501_GPIO26 | SM501_GPIO27)
-#define DS1620_DQ			SM501_GPIO29	/* I/O             */
-#define DS1620_CLK			SM501_GPIO30	/* High active O/P */
-#define DS1620_RES			SM501_GPIO31	/* Low active O/P  */
-/* BC3450 GPIOs @ SM501 Data HIGH */
-#define BUZZER				SM501_GPIO47	/* Low active O/P  */
-#define DS1620_TLOW			SM501_GPIO48	/* High active I/P */
-#define PWR_OFF				SM501_GPIO49	/* Low active O/P  */
-#define FP_DATA_TRI			SM501_GPIO50	/* High active O/P */
-
-
-/*
- * Initialise GPIO on SM501
- *
- * This function may be called from several other functions.
- * Yet, the initialisation sequence is executed only the first
- * time the function is called.
- */
-int sm501_gpio_init (void)
-{
-	static int init_done = 0;
-
-	if (init_done) {
-		debug("sm501_gpio_init: nothing to be done.\n");
-		return 1;
-	}
-
-	/* enable SM501 GPIO control (in both power modes) */
-	*(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE0_GATE) |=
-		POWER_MODE_GATE_GPIO_PWM_I2C;
-	*(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE1_GATE) |=
-		POWER_MODE_GATE_GPIO_PWM_I2C;
-
-	/* set up default O/Ps */
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
-		~(DS1620_RES | DS1620_CLK);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_DQ;
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
-		~(FP_DATA_TRI);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
-		(BUZZER | PWR_OFF);
-
-	/* configure directions for SM501 GPIO pins */
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_LOW) &= ~(0xFF << 24);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_HIGH) &=
-		~(0x3F << 14);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &=
-		~(DIP | DS1620_DQ);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |=
-		(DS1620_RES | DS1620_CLK);
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) &=
-		~DS1620_TLOW;
-	*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) |=
-		(PWR_OFF | BUZZER | FP_DATA_TRI);
-
-	init_done = 1;
-	debug("sm501_gpio_init: done.\n");
-
-	return 0;
-}
-
-
-/*
- * dip - read Config Inputs
- *
- * read and prints the dip switch
- * and/or external config inputs (4bits) 0...0x0F
- */
-int cmd_dip (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	vu_long rc = 0;
-
-	sm501_gpio_init ();
-
-	/* read dip switch */
-	rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
-	rc = ~rc;
-	rc &= DIP;
-	rc = (int) (rc >> 24);
-
-	/* plausibility check */
-	if (rc > 0x0F)
-		return -1;
-
-	printf ("0x%lx\n", rc);
-	return 0;
-}
-
-U_BOOT_CMD (dip, 1, 1, cmd_dip,
-	    "read dip switch and config inputs",
-	    "\n"
-	    "     - prints the state of the dip switch and/or\n"
-	    "       external configuration inputs as hex value.\n"
-	    "     - \"Config 1\" is the LSB");
-
-
-/*
- * buz - turns Buzzer on/off
- */
-#ifdef CONFIG_BC3450_BUZZER
-static int cmd_buz (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	if (argc != 2) {
-		printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
-		return 1;
-	}
-
-	sm501_gpio_init ();
-
-	if (strncmp (argv[1], "on", 2) == 0) {
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
-			~(BUZZER);
-		return 0;
-	} else if (strncmp (argv[1], "off", 3) == 0) {
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
-			BUZZER;
-		return 0;
-	}
-	printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
-	return 1;
-}
-
-U_BOOT_CMD (buz, 2, 1, cmd_buz,
-	    "turns buzzer on/off",
-	    "\n" "buz <on/off>\n" "     - turns the buzzer on or off");
-#endif /* CONFIG_BC3450_BUZZER */
-
-
-/*
- * fp - front panel commands
- */
-static int cmd_fp (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	sm501_gpio_init ();
-
-	if (strncmp (argv[1], "on", 2) == 0) {
-		/* turn on VDD first */
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_VDDEN;
-		udelay (1000);
-		/* then put data on */
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_DATA;
-		/* wait some time and enable backlight */
-		udelay (1000);
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_BIAS;
-		udelay (1000);
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_FPEN;
-		return 0;
-	} else if (strncmp (argv[1], "off", 3) == 0) {
-		/* turn off the backlight first */
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_FPEN;
-		udelay (1000);
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_BIAS;
-		udelay (200000);
-		/* wait some time, then remove data */
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_DATA;
-		udelay (1000);
-		/* and remove VDD last */
-		*(vu_long *) (SM501_MMIO_BASE +
-			      SM501_PANEL_DISPLAY_CONTROL) &=
-			~SM501_PDC_VDDEN;
-		return 0;
-	} else if (strncmp (argv[1], "bl", 2) == 0) {
-		/* turn on/off backlight only */
-		if (strncmp (argv[2], "on", 2) == 0) {
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_PANEL_DISPLAY_CONTROL) |=
-				SM501_PDC_BIAS;
-			udelay (1000);
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_PANEL_DISPLAY_CONTROL) |=
-				SM501_PDC_FPEN;
-			return 0;
-		} else if (strncmp (argv[2], "off", 3) == 0) {
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_PANEL_DISPLAY_CONTROL) &=
-				~SM501_PDC_FPEN;
-			udelay (1000);
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_PANEL_DISPLAY_CONTROL) &=
-				~SM501_PDC_BIAS;
-			return 0;
-		}
-	}
-#ifdef CONFIG_BC3450_CRT
-	else if (strncmp (argv[1], "crt", 3) == 0) {
-		/* enables/disables the crt output (debug only) */
-		if (strncmp (argv[2], "on", 2) == 0) {
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_CRT_DISPLAY_CONTROL) |=
-				(SM501_CDC_TE | SM501_CDC_E);
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_CRT_DISPLAY_CONTROL) &=
-				~SM501_CDC_SEL;
-			return 0;
-		} else if (strncmp (argv[2], "off", 3) == 0) {
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_CRT_DISPLAY_CONTROL) &=
-				~(SM501_CDC_TE | SM501_CDC_E);
-			*(vu_long *) (SM501_MMIO_BASE +
-				      SM501_CRT_DISPLAY_CONTROL) |=
-				SM501_CDC_SEL;
-			return 0;
-		}
-	}
-#endif /* CONFIG_BC3450_CRT */
-	printf ("Usage:%s\n", cmdtp->help);
-	return 1;
-}
-
-U_BOOT_CMD (fp, 3, 1, cmd_fp,
-	    "front panes access functions",
-	    "\n"
-	    "fp bl <on/off>\n"
-	    "     - turns the CCFL backlight of the display on/off\n"
-	    "fp <on/off>\n" "     - turns the whole display on/off"
-#ifdef CONFIG_BC3450_CRT
-	    "\n"
-	    "fp crt <on/off>\n"
-	    "     - enables/disables the crt output (debug only)"
-#endif /* CONFIG_BC3450_CRT */
-	);
-
-/*
- * temp - DS1620 thermometer
- */
-/* GERSYS BC3450 specific functions */
-static inline void bc_ds1620_set_clk (int clk)
-{
-	if (clk)
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
-			DS1620_CLK;
-	else
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
-			~DS1620_CLK;
-}
-
-static inline void bc_ds1620_set_data (int dat)
-{
-	if (dat)
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
-			DS1620_DQ;
-	else
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
-			~DS1620_DQ;
-}
-
-static inline int bc_ds1620_get_data (void)
-{
-	vu_long rc;
-
-	rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
-	rc &= DS1620_DQ;
-	if (rc != 0)
-		rc = 1;
-	return (int) rc;
-}
-
-static inline void bc_ds1620_set_data_dir (int dir)
-{
-	if (dir)		/* in */
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &= ~DS1620_DQ;
-	else			/* out */
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |= DS1620_DQ;
-}
-
-static inline void bc_ds1620_set_reset (int res)
-{
-	if (res)
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_RES;
-	else
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_RES;
-}
-
-/* hardware independent functions */
-static void ds1620_send_bits (int nr, int value)
-{
-	int i;
-
-	for (i = 0; i < nr; i++) {
-		bc_ds1620_set_data (value & 1);
-		bc_ds1620_set_clk (0);
-		udelay (1);
-		bc_ds1620_set_clk (1);
-		udelay (1);
-
-		value >>= 1;
-	}
-}
-
-static unsigned int ds1620_recv_bits (int nr)
-{
-	unsigned int value = 0, mask = 1;
-	int i;
-
-	bc_ds1620_set_data (0);
-
-	for (i = 0; i < nr; i++) {
-		bc_ds1620_set_clk (0);
-		udelay (1);
-
-		if (bc_ds1620_get_data ())
-			value |= mask;
-
-		mask <<= 1;
-
-		bc_ds1620_set_clk (1);
-		udelay (1);
-	}
-
-	return value;
-}
-
-static void ds1620_out (int cmd, int bits, int value)
-{
-	bc_ds1620_set_clk (1);
-	bc_ds1620_set_data_dir (0);
-
-	bc_ds1620_set_reset (0);
-	udelay (1);
-	bc_ds1620_set_reset (1);
-
-	udelay (1);
-
-	ds1620_send_bits (8, cmd);
-	if (bits)
-		ds1620_send_bits (bits, value);
-
-	udelay (1);
-
-	/* go stand alone */
-	bc_ds1620_set_data_dir (1);
-	bc_ds1620_set_reset (0);
-	bc_ds1620_set_clk (0);
-
-	udelay (10000);
-}
-
-static unsigned int ds1620_in (int cmd, int bits)
-{
-	unsigned int value;
-
-	bc_ds1620_set_clk (1);
-	bc_ds1620_set_data_dir (0);
-
-	bc_ds1620_set_reset (0);
-	udelay (1);
-	bc_ds1620_set_reset (1);
-
-	udelay (1);
-
-	ds1620_send_bits (8, cmd);
-
-	bc_ds1620_set_data_dir (1);
-	value = ds1620_recv_bits (bits);
-
-	/* go stand alone */
-	bc_ds1620_set_data_dir (1);
-	bc_ds1620_set_reset (0);
-	bc_ds1620_set_clk (0);
-
-	return value;
-}
-
-static int cvt_9_to_int (unsigned int val)
-{
-	if (val & 0x100)
-		val |= 0xfffffe00;
-
-	return val;
-}
-
-/* set thermostate thresholds */
-static void ds1620_write_state (struct therm *therm)
-{
-	ds1620_out (THERM_WRITE_TL, 9, therm->lo);
-	ds1620_out (THERM_WRITE_TH, 9, therm->hi);
-	ds1620_out (THERM_START_CONVERT, 0, 0);
-}
-
-static int cmd_temp (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	int i;
-	struct therm therm;
-
-	sm501_gpio_init ();
-
-	/* print temperature */
-	if (argc == 1) {
-		i = cvt_9_to_int (ds1620_in (THERM_READ_TEMP, 9));
-		printf ("%d.%d C\n", i >> 1, i & 1 ? 5 : 0);
-		return 0;
-	}
-
-	/* set to default operation */
-	if (strncmp (argv[1], "set", 3) == 0) {
-		if (strncmp (argv[2], "default", 3) == 0) {
-			therm.hi = +88;
-			therm.lo = -20;
-			therm.hi <<= 1;
-			therm.lo <<= 1;
-			ds1620_write_state (&therm);
-			ds1620_out (THERM_WRITE_CONFIG, 8, CONFIG_SYS_STANDALONE);
-			return 0;
-		}
-	}
-
-	printf ("Usage:%s\n", cmdtp->help);
-	return 1;
-}
-
-U_BOOT_CMD (temp, 3, 1, cmd_temp,
-	    "print current temperature",
-	    "\n" "temp\n" "     - print current temperature");
-
-#ifdef CONFIG_BC3450_CAN
-/*
- * Initialise CAN interface
- *
- * return 1 on CAN initialization failure
- * return 0 if no failure
- */
-int can_init (void)
-{
-	static int init_done = 0;
-	int i;
-	struct mpc5xxx_mscan *can1 =
-		(struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0900);
-	struct mpc5xxx_mscan *can2 =
-		(struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0980);
-
-	/* GPIO configuration of the CAN pins is done in BC3450.h */
-
-	if (!init_done) {
-		/* init CAN 1 */
-		can1->canctl1 |= 0x80;	/* CAN enable */
-		udelay (100);
-
-		i = 0;
-		can1->canctl0 |= 0x02;	/* sleep mode */
-		/* wait until sleep mode reached */
-		while (!(can1->canctl1 & 0x02)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN1 initialize error, "
-					"can not enter sleep mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-		i = 0;
-		can1->canctl0 = 0x01;	/* enter init mode */
-		/* wait until init mode reached */
-		while (!(can1->canctl1 & 0x01)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN1 initialize error, "
-					"can not enter init mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-		can1->canctl1 = 0x80;
-		can1->canctl1 |= 0x40;
-		can1->canbtr0 = 0x0F;
-		can1->canbtr1 = 0x7F;
-		can1->canidac &= ~(0x30);
-		can1->canidar1 = 0x00;
-		can1->canidar3 = 0x00;
-		can1->canidar5 = 0x00;
-		can1->canidar7 = 0x00;
-		can1->canidmr0 = 0xFF;
-		can1->canidmr1 = 0xFF;
-		can1->canidmr2 = 0xFF;
-		can1->canidmr3 = 0xFF;
-		can1->canidmr4 = 0xFF;
-		can1->canidmr5 = 0xFF;
-		can1->canidmr6 = 0xFF;
-		can1->canidmr7 = 0xFF;
-
-		i = 0;
-		can1->canctl0 &= ~(0x01);	/* leave init mode */
-		can1->canctl0 &= ~(0x02);
-		/* wait until init and sleep mode left */
-		while ((can1->canctl1 & 0x01) || (can1->canctl1 & 0x02)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN1 initialize error, "
-					"can not leave init/sleep mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-
-		/* init CAN 2 */
-		can2->canctl1 |= 0x80;	/* CAN enable */
-		udelay (100);
-
-		i = 0;
-		can2->canctl0 |= 0x02;	/* sleep mode */
-		/* wait until sleep mode reached */
-		while (!(can2->canctl1 & 0x02)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN2 initialize error, "
-					"can not enter sleep mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-		i = 0;
-		can2->canctl0 = 0x01;	/* enter init mode */
-		/* wait until init mode reached */
-		while (!(can2->canctl1 & 0x01)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN2 initialize error, "
-					"can not enter init mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-		can2->canctl1 = 0x80;
-		can2->canctl1 |= 0x40;
-		can2->canbtr0 = 0x0F;
-		can2->canbtr1 = 0x7F;
-		can2->canidac &= ~(0x30);
-		can2->canidar1 = 0x00;
-		can2->canidar3 = 0x00;
-		can2->canidar5 = 0x00;
-		can2->canidar7 = 0x00;
-		can2->canidmr0 = 0xFF;
-		can2->canidmr1 = 0xFF;
-		can2->canidmr2 = 0xFF;
-		can2->canidmr3 = 0xFF;
-		can2->canidmr4 = 0xFF;
-		can2->canidmr5 = 0xFF;
-		can2->canidmr6 = 0xFF;
-		can2->canidmr7 = 0xFF;
-		can2->canctl0 &= ~(0x01);	/* leave init mode */
-		can2->canctl0 &= ~(0x02);
-
-		i = 0;
-		/* wait until init mode left */
-		while ((can2->canctl1 & 0x01) || (can2->canctl1 & 0x02)) {
-			udelay (10);
-			i++;
-			if (i == 10) {
-				printf ("%s: CAN2 initialize error, "
-					"can not leave init/sleep mode!\n",
-					__FUNCTION__);
-				return 1;
-			}
-		}
-		init_done = 1;
-	}
-	return 0;
-}
-
-/*
- * Do CAN test
- * by sending message between CAN1 and CAN2
- *
- * return 1 on CAN failure
- * return 0 if no failure
- */
-int do_can (char * const argv[])
-{
-	int i;
-	struct mpc5xxx_mscan *can1 =
-		(struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0900);
-	struct mpc5xxx_mscan *can2 =
-		(struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0980);
-
-	/* send a message on CAN1 */
-	can1->cantbsel = 0x01;
-	can1->cantxfg.idr[0] = 0x55;
-	can1->cantxfg.idr[1] = 0x00;
-	can1->cantxfg.idr[1] &= ~0x8;
-	can1->cantxfg.idr[1] &= ~0x10;
-	can1->cantxfg.dsr[0] = 0xCC;
-	can1->cantxfg.dlr = 1;
-	can1->cantxfg.tbpr = 0;
-	can1->cantflg = 0x01;
-
-	i = 0;
-	while ((can1->cantflg & 0x01) == 0) {
-		i++;
-		if (i == 10) {
-			printf ("%s: CAN1 send timeout, "
-				"can not send message!\n", __FUNCTION__);
-			return 1;
-		}
-		udelay (1000);
-	}
-	udelay (1000);
-
-	i = 0;
-	while (!(can2->canrflg & 0x01)) {
-		i++;
-		if (i == 10) {
-			printf ("%s: CAN2 receive timeout, "
-				"no message received!\n", __FUNCTION__);
-			return 1;
-		}
-		udelay (1000);
-	}
-
-	if (can2->canrxfg.dsr[0] != 0xCC) {
-		printf ("%s: CAN2 receive error, "
-			"data mismatch!\n", __FUNCTION__);
-		return 1;
-	}
-
-	/* send a message on CAN2 */
-	can2->cantbsel = 0x01;
-	can2->cantxfg.idr[0] = 0x55;
-	can2->cantxfg.idr[1] = 0x00;
-	can2->cantxfg.idr[1] &= ~0x8;
-	can2->cantxfg.idr[1] &= ~0x10;
-	can2->cantxfg.dsr[0] = 0xCC;
-	can2->cantxfg.dlr = 1;
-	can2->cantxfg.tbpr = 0;
-	can2->cantflg = 0x01;
-
-	i = 0;
-	while ((can2->cantflg & 0x01) == 0) {
-		i++;
-		if (i == 10) {
-			printf ("%s: CAN2 send error, "
-				"can not send message!\n", __FUNCTION__);
-			return 1;
-		}
-		udelay (1000);
-	}
-	udelay (1000);
-
-	i = 0;
-	while (!(can1->canrflg & 0x01)) {
-		i++;
-		if (i == 10) {
-			printf ("%s: CAN1 receive timeout, "
-				"no message received!\n", __FUNCTION__);
-			return 1;
-		}
-		udelay (1000);
-	}
-
-	if (can1->canrxfg.dsr[0] != 0xCC) {
-		printf ("%s: CAN1 receive error 0x%02x\n",
-			__FUNCTION__, (can1->canrxfg.dsr[0]));
-		return 1;
-	}
-
-	return 0;
-}
-#endif /* CONFIG_BC3450_CAN */
-
-/*
- * test - BC3450 HW test routines
- */
-int cmd_test (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-#ifdef CONFIG_BC3450_CAN
-	int rcode;
-
-	can_init ();
-#endif /* CONFIG_BC3450_CAN */
-
-	sm501_gpio_init ();
-
-	if (argc != 2) {
-		printf ("Usage:%s\n", cmdtp->help);
-		return 1;
-	}
-
-	if (strncmp (argv[1], "unit-off", 8) == 0) {
-		printf ("waiting 2 seconds...\n");
-		udelay (2000000);
-		*(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
-			~PWR_OFF;
-		return 0;
-	}
-#ifdef CONFIG_BC3450_CAN
-	else if (strncmp (argv[1], "can", 2) == 0) {
-		rcode = do_can (argv);
-		if (simple_strtoul (argv[2], NULL, 10) == 2) {
-			if (rcode == 0)
-				printf ("OK\n");
-			else
-				printf ("Error\n");
-		}
-		return rcode;
-	}
-#endif /* CONFIG_BC3450_CAN */
-
-	printf ("Usage:%s\n", cmdtp->help);
-	return 1;
-}
-
-U_BOOT_CMD (test, 2, 1, cmd_test, "unit test routines", "\n"
-#ifdef CONFIG_BC3450_CAN
-	"test can\n"
-	"     - connect CAN1 (X8) with CAN2 (X9) for this test\n"
-#endif /* CONFIG_BC3450_CAN */
-	"test unit-off\n"
-	"     - turns off the BC3450 unit\n"
-	"       WARNING: Unsaved environment variables will be lost!"
-);
-#endif
diff --git a/board/bc3450/mt48lc16m16a2-75.h b/board/bc3450/mt48lc16m16a2-75.h
deleted file mode 100644
index 3d9979664f3..00000000000
--- a/board/bc3450/mt48lc16m16a2-75.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#define SDRAM_DDR	0		/* is SDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE	0x00CD0000
-/* #define SDRAM_MODE	0x008D0000 */ /* CAS latency 2 */
-#define SDRAM_CONTROL	0x504F0000
-#define SDRAM_CONFIG1	0xD2322800
-/* #define SDRAM_CONFIG1	0xD2222800 */ /* CAS latency 2 */
-/*#define SDRAM_CONFIG1	0xD7322800 */ /* SDRAM controller bug workaround */
-#define SDRAM_CONFIG2	0x8AD70000
-/*#define SDRAM_CONFIG2	0xDDD70000 */ /* SDRAM controller bug workaround */