Merge remote-tracking branch 'u-boot-marvell/master'

12 files changed, 633 insertions, 5 deletions

diff --git a/board/LaCie/common/common.c b/board/LaCie/common/common.c
index 78d0edc66d8..a62bf9f1896 100644
--- a/board/LaCie/common/common.c
+++ b/board/LaCie/common/common.c
@@ -13,10 +13,11 @@
 
 #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
 
+#define MII_MARVELL_PHY_PAGE		22
+
 #define MV88E1116_LED_FCTRL_REG		10
 #define MV88E1116_CPRSP_CR3_REG		21
 #define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
 #define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
 #define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
 
@@ -31,15 +32,44 @@ void mv_phy_88e1116_init(const char *name, u16 phyaddr)
 	 * Enable RGMII delay on Tx and Rx for CPU port
 	 * Ref: sec 4.7.2 of chip datasheet
 	 */
-	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
+	miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2);
 	miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
 	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
 	miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
+	miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0);
 
 	if (miiphy_reset(name, phyaddr) == 0)
 		printf("88E1116 Initialized on %s\n", name);
 }
+
+void mv_phy_88e1318_init(const char *name, u16 phyaddr)
+{
+	u16 reg;
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/*
+	 * Set control mode 4 for LED[0].
+	 */
+	miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 3);
+	miiphy_read(name, phyaddr, 16, &reg);
+	reg |= 0xf;
+	miiphy_write(name, phyaddr, 16, reg);
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2);
+	miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_TXTM_CTRL | MV88E1116_RGMII_RXTM_CTRL);
+	miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0);
+
+	if (miiphy_reset(name, phyaddr) == 0)
+		printf("88E1318 Initialized on %s\n", name);
+}
 #endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */
 
 #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
diff --git a/board/LaCie/common/common.h b/board/LaCie/common/common.h
index 2edd5abbcd0..85e433c9316 100644
--- a/board/LaCie/common/common.h
+++ b/board/LaCie/common/common.h
@@ -12,6 +12,7 @@
 
 #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
 void mv_phy_88e1116_init(const char *name, u16 phyaddr);
+void mv_phy_88e1318_init(const char *name, u16 phyaddr);
 #endif
 #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
 int lacie_read_mac_address(uchar *mac);
diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
new file mode 100644
index 00000000000..d008eb0ab0b
--- /dev/null
+++ b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
@@ -0,0 +1,162 @@
+#
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi	# Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1B1B1B9B
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000618	# DDR Configuration register
+# bit13-0:  0xa00 (2560 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x34143000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x11012228	# DDR Timing (Low) (active cycles value +1)
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000A19	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000DDDD	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
+# bit3-2:   10, Cs0size=512Mb
+# bit5-4:   00, Cs2width=nonexistent
+# bit7-6:   00, Cs1size =nonexistent
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000632	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    1,  DDR drive strenght reduced
+# bit2:    1,  DDR ODT control lsd enabled
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, enabled
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F07F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  1  , D2P Latency enabled
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
+# bit3-0:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
+# bit3-0:  1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
+# bit7-4:  1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
+# bit11-10:1, DQ_ODTSel. ODT select turned on
+
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c
index 68e8a770c79..101a80a70ab 100644
--- a/board/LaCie/netspace_v2/netspace_v2.c
+++ b/board/LaCie/netspace_v2/netspace_v2.c
@@ -107,7 +107,11 @@ int misc_init_r(void)
 /* Configure and initialize PHY */
 void reset_phy(void)
 {
+#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
+	mv_phy_88e1318_init("egiga0", 0);
+#else
 	mv_phy_88e1116_init("egiga0", 8);
+#endif
 }
 #endif
 
diff --git a/board/buffalo/lsxl/lsxl.c b/board/buffalo/lsxl/lsxl.c
index b3f31d6b697..57776fb0774 100644
--- a/board/buffalo/lsxl/lsxl.c
+++ b/board/buffalo/lsxl/lsxl.c
@@ -195,9 +195,11 @@ int board_init(void)
 static void check_power_switch(void)
 {
 	if (kw_gpio_get_value(GPIO_POWER_SWITCH)) {
-		/* turn off HDD and USB power */
+		/* turn off fan, HDD and USB power */
 		kw_gpio_set_value(GPIO_HDD_POWER, 0);
 		kw_gpio_set_value(GPIO_USB_VBUS, 0);
+		kw_gpio_set_value(GPIO_FAN_HIGH, 1);
+		kw_gpio_set_value(GPIO_FAN_LOW, 1);
 		set_led(LED_OFF);
 
 		/* loop until released */
@@ -207,6 +209,8 @@ static void check_power_switch(void)
 		/* turn power on again */
 		kw_gpio_set_value(GPIO_HDD_POWER, 1);
 		kw_gpio_set_value(GPIO_USB_VBUS, 1);
+		kw_gpio_set_value(GPIO_FAN_HIGH, 0);
+		kw_gpio_set_value(GPIO_FAN_LOW, 0);
 		set_led(LED_POWER_BLINKING);
 	}
 }
diff --git a/board/iomega/iconnect/Makefile b/board/iomega/iconnect/Makefile
new file mode 100644
index 00000000000..f77fcfb9901
--- /dev/null
+++ b/board/iomega/iconnect/Makefile
@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= iconnect.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/iomega/iconnect/iconnect.c b/board/iomega/iconnect/iconnect.c
new file mode 100644
index 00000000000..6ee2128aab8
--- /dev/null
+++ b/board/iomega/iconnect/iconnect.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright (C) 2009-2012
+ * Wojciech Dubowik <wojciech.dubowik@neratec.com>
+ * Luka Perkov <uboot@lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "iconnect.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the below configuration configures mainly initial LED status
+	 */
+	kw_config_gpio(ICONNECT_OE_VAL_LOW,
+			ICONNECT_OE_VAL_HIGH,
+			ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,	/* Reset signal */
+		MPP7_GPO,
+		MPP8_TW_SDA,		/* I2C */	
+		MPP9_TW_SCK,		/* I2C */
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_GPO,		/* Reset button */
+		MPP13_SD_CMD,
+		MPP14_SD_D0,
+		MPP15_SD_D1,
+		MPP16_SD_D2,
+		MPP17_SD_D3,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GE1_0,
+		MPP21_GE1_1,
+		MPP22_GE1_2,
+		MPP23_GE1_3,
+		MPP24_GE1_4,
+		MPP25_GE1_5,
+		MPP26_GE1_6,
+		MPP27_GE1_7,
+		MPP28_GPIO,
+		MPP29_GPIO,
+		MPP30_GE1_10,
+		MPP31_GE1_11,
+		MPP32_GE1_12,
+		MPP33_GE1_13,
+		MPP34_GE1_14,
+		MPP35_GPIO,		/* OTB button */
+		MPP36_AUDIO_SPDIFI,
+		MPP37_AUDIO_SPDIFO,
+		MPP38_GPIO,
+		MPP39_TDM_SPI_CS0,
+		MPP40_TDM_SPI_SCK,
+		MPP41_GPIO,		/* LED brightness */
+		MPP42_GPIO,		/* LED power (blue) */
+		MPP43_GPIO,		/* LED power (red) */
+		MPP44_GPIO,		/* LED USB 1 */
+		MPP45_GPIO,		/* LED USB 2 */
+		MPP46_GPIO,		/* LED USB 3 */
+		MPP47_GPIO,		/* LED USB 4 */
+		MPP48_GPIO,		/* LED OTB */
+		MPP49_GPIO,
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+	return 0;
+}
diff --git a/board/iomega/iconnect/iconnect.h b/board/iomega/iconnect/iconnect.h
new file mode 100644
index 00000000000..2fb3e5ed8f2
--- /dev/null
+++ b/board/iomega/iconnect/iconnect.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2009-2012
+ * Wojciech Dubowik <wojciech.dubowik@neratec.com>
+ * Luka Perkov <uboot@lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __ICONNECT_H
+#define __ICONNECT_H
+
+#define ICONNECT_OE_LOW			(~(1 << 7))
+#define ICONNECT_OE_HIGH		(~(1 << 10))
+#define ICONNECT_OE_VAL_LOW		(0)
+#define ICONNECT_OE_VAL_HIGH		(1 << 10)
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG		10
+#define MV88E1116_CPRSP_CR3_REG		21
+#define MV88E1116_MAC_CTRL_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+#endif /* __ICONNECT_H */
diff --git a/board/iomega/iconnect/kwbimage.cfg b/board/iomega/iconnect/kwbimage.cfg
new file mode 100644
index 00000000000..6c9dfe3d31d
--- /dev/null
+++ b/board/iomega/iconnect/kwbimage.cfg
@@ -0,0 +1,165 @@
+#
+# (C) Copyright 2009-2012
+# Wojciech Dubowik <wojciech.dubowik@neratec.com>
+# Luka Perkov <uboot@lukaperkov.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	nand
+NAND_ECC_MODE	default
+NAND_PAGE_SIZE	0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xffd100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xffd01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30, (3120 DDR2 clks refresh rate)
+# bit23-14: 0x0,
+# bit24:    0x1,   enable exit self refresh mode on DDR access
+# bit25:    0x1,   required
+# bit29-26: 0x0,
+# bit31-30: 0x1,
+
+DATA 0xffd01404 0x37543000	# DDR Controller Control Low
+# bit4:     0x0, addr/cmd in smame cycle
+# bit5:     0x0, clk is driven during self refresh, we don't care for APX
+# bit6:     0x0, use recommended falling edge of clk for addr/cmd
+# bit14:    0x0, input buffer always powered up
+# bit18:    0x1, cpu lock transaction enabled
+# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 0x3, required
+# bit31:    0x0, no additional STARTBURST delay
+
+DATA 0xffd01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11-8:  TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xffd0140c 0x00000a33	# DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: 0x0, required
+
+DATA 0xffd01410 0x000000cc	# DDR Address Control
+# bit1-0:   00,  Cs0width (x8)
+# bit3-2:   11,  Cs0size (1Gb)
+# bit5-4:   00,  Cs1width (x8)
+# bit7-6:   11,  Cs1size (1Gb)
+# bit9-8:   00,  Cs2width (nonexistent)
+# bit11-10: 00,  Cs2size (nonexistent)
+# bit13-12: 00,  Cs3width (nonexistent)
+# bit15-14: 00,  Cs3size (nonexistent)
+# bit16:    0,   Cs0AddrSel
+# bit17:    0,   Cs1AddrSel
+# bit18:    0,   Cs2AddrSel
+# bit19:    0,   Cs3AddrSel
+# bit31-20: 0x0, required
+
+DATA 0xffd01414 0x00000000	# DDR Open Pages Control
+# bit0:    0,   OpenPage enabled
+# bit31-1: 0x0, required
+
+DATA 0xffd01418 0x00000000	# DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0x0, required
+
+DATA 0xffd0141c 0x00000c52	# DDR Mode
+# bit2-0:   0x2, BurstLen=2 required
+# bit3:     0x0, BurstType=0 required
+# bit6-4:   0x4, CL=5
+# bit7:     0x0, TestMode=0 normal
+# bit8:     0x0, DLL reset=0 normal
+# bit11-9:  0x6, auto-precharge write recovery ????????????
+# bit12:    0x0, PD must be zero
+# bit31-13: 0x0, required
+
+DATA 0xffd01420 0x00000040	# DDR Extended Mode
+# bit0:     0,   DDR DLL enabled
+# bit1:     0,   DDR drive strenght normal
+# bit2:     0,   DDR ODT control lsd (disabled)
+# bit5-3:   0x0, required
+# bit6:     1,   DDR ODT control msb, (disabled)
+# bit9-7:   0x0, required
+# bit10:    0,   differential DQS enabled
+# bit11:    0,   required
+# bit12:    0,   DDR output buffer enabled
+# bit31-13: 0x0, required
+
+DATA 0xffd01424 0x0000f17f	# DDR Controller Control High
+# bit2-0:   0x7, required
+# bit3:     0x1, MBUS Burst Chop disabled
+# bit6-4:   0x7, required
+# bit7:     0x0,
+# bit8:     0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9:     0x0, no half clock cycle addition to dataout
+# bit10:    0x0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11:    0x0, 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 0xf, required
+# bit31-16: 0x0, required
+
+DATA 0xffd01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xffd0147c 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xffd01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xffd01504 0x0ffffff1	# CS[0]n Size
+# bit0:     0x1,     Window enabled
+# bit1:     0x0,     Write Protect disabled
+# bit3-2:   0x0,     CS0 hit selected
+# bit23-4:  0xfffff, required
+# bit31-24: 0x0f,    Size (i.e. 256MB)
+
+DATA 0xffd01508 0x00000000	# CS[1]n Base address to 256Mb
+DATA 0xffd0150c 0x00000000	# CS[1]n Size, window disabled
+
+DATA 0xffd01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xffd0151c 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xffd01494 0x00030000	# DDR ODT Control (Low)
+# bit3-0:     ODT0Rd, MODT[0] asserted during read from DRAM CS1
+# bit7-4:     ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
+# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xffd01498 0x00000000	# DDR ODT Control (High)
+# bit1-0:  0x0, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  0x1, ODT1 active NEVER!
+# bit31-4: 0x0, required
+
+DATA 0xffd0149c 0x0000e803	# CPU ODT Control
+DATA 0xffd01480 0x00000001	# DDR Initialization Control
+# bit0: 0x1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index be8f51c2fc4..0c4dddc6173 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -250,7 +250,8 @@ int board_early_init_f(void)
 	tmp = readl(KW_GPIO0_BASE + 4);
 	writel(tmp & (~KM_KIRKWOOD_SOFT_I2C_GPIOS) , KW_GPIO0_BASE + 4);
 #endif
-
+	/* adjust SDRAM size for bank 0 */
+	kw_sdram_size_adjust(0);
 	kirkwood_mpp_conf(kwmpp_config, NULL);
 	return 0;
 }
@@ -365,6 +366,71 @@ void reset_phy(void)
 	/* reset the phy */
 	miiphy_reset(name, CONFIG_PHY_BASE_ADR);
 }
+#elif defined(CONFIG_KM_PIGGY4_88E6352)
+
+#include <mv88e6352.h>
+
+#if defined(CONFIG_KM_NUSA)
+struct mv88e_sw_reg extsw_conf[] = {
+	/*
+	 * port 0, PIGGY4, autoneg 
+	 * first the fix for the 1000Mbits Autoneg, this is from
+	 * a Marvell errata, the regs are undocumented
+	 */
+	{ PHY(0), PHY_PAGE, AN1000FIX_PAGE },
+	{ PHY(0), PHY_STATUS, AN1000FIX },
+	{ PHY(0), PHY_PAGE, 0 },
+	/* now the real port and phy configuration */
+	{ PORT(0), PORT_PHY, NO_SPEED_FOR },
+	{ PORT(0), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+	{ PHY(0), PHY_1000_CTRL, NO_ADV },
+	{ PHY(0), PHY_SPEC_CTRL, AUTO_MDIX_EN },
+	{ PHY(0), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
+		FULL_DUPLEX },
+	/* port 1, unused */
+	{ PORT(1), PORT_CTRL, PORT_DIS },
+	{ PHY(1), PHY_CTRL, PHY_PWR_DOWN },
+	{ PHY(1), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+	/* port 2, unused */
+	{ PORT(2), PORT_CTRL, PORT_DIS },
+	{ PHY(2), PHY_CTRL, PHY_PWR_DOWN },
+	{ PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+	/* port 3, unused */
+	{ PORT(3), PORT_CTRL, PORT_DIS },
+	{ PHY(3), PHY_CTRL, PHY_PWR_DOWN },
+	{ PHY(3), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+	/* port 4, ICNEV, SerDes, SGMII */
+	{ PORT(4), PORT_STATUS, NO_PHY_DETECT },
+	{ PORT(4), PORT_PHY, SPEED_1000_FOR },
+	{ PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+	{ PHY(4), PHY_CTRL, PHY_PWR_DOWN },
+	{ PHY(4), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+	/* port 5, CPU_RGMII */
+	{ PORT(5), PORT_PHY, RX_RGMII_TIM | TX_RGMII_TIM | FLOW_CTRL_EN |
+		FLOW_CTRL_FOR | LINK_VAL | LINK_FOR | FULL_DPX |
+		FULL_DPX_FOR | SPEED_1000_FOR },
+	{ PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+	/* port 6, unused, this port has no phy */
+	{ PORT(6), PORT_CTRL, PORT_DIS },
+};
+#else
+struct mv88e_sw_reg extsw_conf[] = {};
+#endif
+
+void reset_phy(void)
+{
+#if defined(CONFIG_KM_MVEXTSW_ADDR)
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
+		ARRAY_SIZE(extsw_conf));
+	mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
+#endif
+}
+
 #else
 /* Configure and enable MV88E1118 PHY on the piggy*/
 void reset_phy(void)
diff --git a/board/raidsonic/ib62x0/ib62x0.c b/board/raidsonic/ib62x0/ib62x0.c
index 1164d6bf3ff..b7e6e4107c5 100644
--- a/board/raidsonic/ib62x0/ib62x0.c
+++ b/board/raidsonic/ib62x0/ib62x0.c
@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <miiphy.h>
+#include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
@@ -41,6 +42,8 @@ int board_early_init_f(void)
 			IB62x0_OE_VAL_HIGH,
 			IB62x0_OE_LOW, IB62x0_OE_HIGH);
 
+	/* Set SATA activity LEDs to default off */
+	writel(MVSATAHC_LED_POLARITY_CTRL, MVSATAHC_LED_CONF_REG);
 	/* Multi-Purpose Pins Functionality configuration */
 	u32 kwmpp_config[] = {
 		MPP0_NF_IO2,
diff --git a/board/raidsonic/ib62x0/ib62x0.h b/board/raidsonic/ib62x0/ib62x0.h
index 0c30690697f..0118c2b69ac 100644
--- a/board/raidsonic/ib62x0/ib62x0.h
+++ b/board/raidsonic/ib62x0/ib62x0.h
@@ -37,4 +37,8 @@
 #define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
 #define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
 
+/* SATAHC related */
+#define MVSATAHC_LED_CONF_REG       (MV_SATA_BASE + 0x2C)
+#define MVSATAHC_LED_POLARITY_CTRL  (1 << 3)
+
 #endif /* __IB62x0_H */