summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
authorBiwen Li <biwen.li@nxp.com>2019-12-31 15:33:41 +0800
committerPriyanka Jain <priyanka.jain@nxp.com>2020-02-04 16:20:25 +0530
commita0affb367ad638e1e6f51ed3678d3daad5724a40 (patch)
treea87af25eca96e994c219b4264588fd4641d48c0d /board
parent6089d8ab31daa04ca693ba2b9c2bfca1e53cfc65 (diff)
dm: arm64: ls1012a: add i2c DM support
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Diffstat (limited to 'board')
-rw-r--r--board/freescale/ls1012aqds/ls1012aqds.c20
-rw-r--r--board/freescale/ls1012ardb/eth.c35
-rw-r--r--board/freescale/ls1012ardb/ls1012ardb.c148
3 files changed, 177 insertions, 26 deletions
diff --git a/board/freescale/ls1012aqds/ls1012aqds.c b/board/freescale/ls1012aqds/ls1012aqds.c
index 86c72ee357..30bf1047d5 100644
--- a/board/freescale/ls1012aqds/ls1012aqds.c
+++ b/board/freescale/ls1012aqds/ls1012aqds.c
@@ -107,10 +107,26 @@ int board_early_init_f(void)
int misc_init_r(void)
{
u8 mux_sdhc_cd = 0x80;
-
- i2c_set_bus_num(0);
+ int bus_num = 0;
+
+#ifdef CONFIG_DM_I2C
+ struct udevice *dev;
+ int ret;
+
+ ret = i2c_get_chip_for_busnum(bus_num, CONFIG_SYS_I2C_FPGA_ADDR,
+ 1, &dev);
+ if (ret) {
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ bus_num);
+ return ret;
+ }
+ dm_i2c_write(dev, 0x5a, &mux_sdhc_cd, 1);
+#else
+ i2c_set_bus_num(bus_num);
i2c_write(CONFIG_SYS_I2C_FPGA_ADDR, 0x5a, 1, &mux_sdhc_cd, 1);
+#endif
+
return 0;
}
#endif
diff --git a/board/freescale/ls1012ardb/eth.c b/board/freescale/ls1012ardb/eth.c
index 3cc0a65cb9..5edcfcf1ce 100644
--- a/board/freescale/ls1012ardb/eth.c
+++ b/board/freescale/ls1012ardb/eth.c
@@ -28,12 +28,47 @@ static inline void ls1012ardb_reset_phy(void)
{
#ifdef CONFIG_TARGET_LS1012ARDB
/* Through reset IO expander reset both RGMII and SGMII PHYs */
+#ifdef CONFIG_DM_I2C
+ struct udevice *dev;
+ int ret;
+
+ /*
+ * The I2C IO-expander PCAL9555A is mouted on I2C1 bus(bus number is 0).
+ */
+ ret = i2c_get_chip_for_busnum(0, I2C_MUX_IO2_ADDR,
+ 1, &dev);
+ if (ret) {
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ 0);
+ return;
+ }
+ /* Config port 0
+ * - config pin IOXP_RST_ETH1_B and IOXP_RST_ETH2_B
+ * are enabled as an output.
+ */
+ dm_i2c_reg_write(dev, 6, __PHY_MASK);
+
+ /*
+ * Set port 0 output a value to reset ETH2 interface
+ * - pin IOXP_RST_ETH2_B output 0b0
+ */
+ dm_i2c_reg_write(dev, 2, __PHY_ETH2_MASK);
+ mdelay(10);
+ dm_i2c_reg_write(dev, 2, __PHY_ETH1_MASK);
+ /*
+ * Set port 0 output a value to reset ETH1 interface
+ * - pin IOXP_RST_ETH1_B output 0b0
+ */
+ mdelay(10);
+ dm_i2c_reg_write(dev, 2, 0xFF);
+#else
i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH1_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF);
+#endif
mdelay(50);
#endif
}
diff --git a/board/freescale/ls1012ardb/ls1012ardb.c b/board/freescale/ls1012ardb/ls1012ardb.c
index 0f665c7bc6..ab83ef11a0 100644
--- a/board/freescale/ls1012ardb/ls1012ardb.c
+++ b/board/freescale/ls1012ardb/ls1012ardb.c
@@ -34,13 +34,27 @@ int checkboard(void)
{
#ifdef CONFIG_TARGET_LS1012ARDB
u8 in1;
+ int ret, bus_num = 0;
puts("Board: LS1012ARDB ");
/* Initialize i2c early for Serial flash bank information */
- i2c_set_bus_num(0);
+#if defined(CONFIG_DM_I2C)
+ struct udevice *dev;
- if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &in1, 1) < 0) {
+ ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_IO_ADDR,
+ 1, &dev);
+ if (ret) {
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ bus_num);
+ return -ENXIO;
+ }
+ ret = dm_i2c_read(dev, I2C_MUX_IO_1, &in1, 1);
+#else /* Non DM I2C support - will be removed */
+ i2c_set_bus_num(bus_num);
+ ret = i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &in1, 1);
+#endif
+ if (ret < 0) {
printf("Error reading i2c boot information!\n");
return 0; /* Don't want to hang() on this error */
}
@@ -175,11 +189,25 @@ int esdhc_status_fixup(void *blob, const char *compat)
bool sdhc2_en = false;
u8 mux_sdhc2;
u8 io = 0;
+ int ret, bus_num = 0;
- i2c_set_bus_num(0);
+#if defined(CONFIG_DM_I2C)
+ struct udevice *dev;
+ ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_IO_ADDR,
+ 1, &dev);
+ if (ret) {
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ bus_num);
+ return -ENXIO;
+ }
+ ret = dm_i2c_read(dev, I2C_MUX_IO_1, &io, 1);
+#else
+ i2c_set_bus_num(bus_num);
/* IO1[7:3] is the field of board revision info. */
- if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &io, 1) < 0) {
+ ret = i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &io, 1);
+#endif
+ if (ret < 0) {
printf("Error reading i2c boot information!\n");
return 0;
}
@@ -202,7 +230,12 @@ int esdhc_status_fixup(void *blob, const char *compat)
* 10 - eMMC Memory
* 11 - SPI
*/
- if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1) < 0) {
+#if defined(CONFIG_DM_I2C)
+ ret = dm_i2c_read(dev, I2C_MUX_IO_0, &io, 1);
+#else
+ ret = i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1);
+#endif
+ if (ret < 0) {
printf("Error reading i2c boot information!\n");
return 0;
}
@@ -233,16 +266,63 @@ int ft_board_setup(void *blob, bd_t *bd)
static int switch_to_bank1(void)
{
- u8 data;
- int ret;
+ u8 data = 0xf4, chip_addr = 0x24, offset_addr = 0x03;
+ int ret, bus_num = 0;
- i2c_set_bus_num(0);
+#if defined(CONFIG_DM_I2C)
+ struct udevice *dev;
+
+ ret = i2c_get_chip_for_busnum(bus_num, chip_addr,
+ 1, &dev);
+ if (ret) {
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ bus_num);
+ return -ENXIO;
+ }
+ /*
+ * --------------------------------------------------------------------
+ * |bus |I2C address| Device | Notes |
+ * --------------------------------------------------------------------
+ * |I2C1|0x24, 0x25,| IO expander (CFG,| Provides 16bits of General |
+ * | |0x26 | RESET, and INT/ | Purpose parallel Input/Output|
+ * | | | KW41GPIO) - NXP | (GPIO) expansion for the |
+ * | | | PCAL9555AHF | I2C bus |
+ * ----- --------------------------------------------------------------
+ * - mount three IO expander(PCAL9555AHF) on I2C1
+ *
+ * PCAL9555A device address
+ * slave address
+ * --------------------------------------
+ * | 0 | 1 | 0 | 0 | A2 | A1 | A0 | R/W |
+ * --------------------------------------
+ * | fixed | hardware selectable|
+ *
+ * Output port 1(Pinter register bits = 0x03)
+ *
+ * P1_[7~0] = 0xf4
+ * P1_0 <---> CFG_MUX_QSPI_S0
+ * P1_1 <---> CFG_MUX_QSPI_S1
+ * CFG_MUX_QSPI_S[1:0] = 0b00
+ *
+ * QSPI chip-select demultiplexer select
+ * ---------------------------------------------------------------------
+ * CFG_MUX_QSPI_S1|CFG_MUX_QSPI_S0| Values
+ * ---------------------------------------------------------------------
+ * 0 | 0 |CS routed to SPI memory bank1(default)
+ * ---------------------------------------------------------------------
+ * 0 | 1 |CS routed to SPI memory bank2
+ * ---------------------------------------------------------------------
+ *
+ */
+ ret = dm_i2c_write(dev, offset_addr, &data, 1);
+#else /* Non DM I2C support - will be removed */
+ i2c_set_bus_num(bus_num);
+ ret = i2c_write(chip_addr, offset_addr, 1, &data, 1);
+#endif
- data = 0xf4;
- ret = i2c_write(0x24, 0x3, 1, &data, 1);
if (ret) {
printf("i2c write error to chip : %u, addr : %u, data : %u\n",
- 0x24, 0x3, data);
+ chip_addr, offset_addr, data);
}
return ret;
@@ -250,25 +330,45 @@ static int switch_to_bank1(void)
static int switch_to_bank2(void)
{
- u8 data;
- int ret;
+ u8 data[2] = {0xfc, 0xf5}, offset_addr[2] = {0x7, 0x3};
+ u8 chip_addr = 0x24;
+ int ret, i, bus_num = 0;
- i2c_set_bus_num(0);
+#if defined(CONFIG_DM_I2C)
+ struct udevice *dev;
- data = 0xfc;
- ret = i2c_write(0x24, 0x7, 1, &data, 1);
+ ret = i2c_get_chip_for_busnum(bus_num, chip_addr,
+ 1, &dev);
if (ret) {
- printf("i2c write error to chip : %u, addr : %u, data : %u\n",
- 0x24, 0x7, data);
- goto err;
+ printf("%s: Cannot find udev for a bus %d\n", __func__,
+ bus_num);
+ return -ENXIO;
}
+#else /* Non DM I2C support - will be removed */
+ i2c_set_bus_num(bus_num);
+#endif
- data = 0xf5;
- ret = i2c_write(0x24, 0x3, 1, &data, 1);
- if (ret) {
- printf("i2c write error to chip : %u, addr : %u, data : %u\n",
- 0x24, 0x3, data);
+ /*
+ * 1th step: config port 1
+ * - the port 1 pin is enabled as an output
+ * 2th step: output port 1
+ * - P1_[7:0] output 0xf5,
+ * then CFG_MUX_QSPI_S[1:0] equal to 0b01,
+ * CS routed to SPI memory bank2
+ */
+ for (i = 0; i < sizeof(data); i++) {
+#if defined(CONFIG_DM_I2C)
+ ret = dm_i2c_write(dev, offset_addr[i], &data[i], 1);
+#else /* Non DM I2C support - will be removed */
+ ret = i2c_write(chip_addr, offset_addr[i], 1, &data[i], 1);
+#endif
+ if (ret) {
+ printf("i2c write error to chip : %u, addr : %u, data : %u\n",
+ chip_addr, offset_addr[i], data[i]);
+ goto err;
+ }
}
+
err:
return ret;
}