Add support for Freescale's mx35pdk board.

The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic <sbabic@denx.de>

1 files changed, 363 insertions, 0 deletions

diff --git a/board/freescale/mx35pdk/lowlevel_init.S b/board/freescale/mx35pdk/lowlevel_init.S
new file mode 100644
index 00000000000..9b0f1b52596
--- /dev/null
+++ b/board/freescale/mx35pdk/lowlevel_init.S
@@ -0,0 +1,363 @@
+/*
+ * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+ *
+ * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/asm-offsets.h>
+#include "mx35pdk.h"
+
+/*
+ * return soc version
+ * 	0x10:  TO1
+ *	0x20:  TO2
+ *	0x30:  TO3
+ */
+.macro check_soc_version ret, tmp
+	ldr \tmp, =IIM_BASE_ADDR
+	ldr \ret, [\tmp, #IIM_SREV]
+	cmp \ret, #0x00
+	moveq \tmp, #ROMPATCH_REV
+	ldreq \ret, [\tmp]
+	moveq \ret, \ret, lsl #4
+	addne \ret, \ret, #0x10
+.endm
+
+/*
+ * AIPS setup - Only setup MPROTx registers.
+ * The PACR default values are good.
+ */
+.macro init_aips
+	/*
+	 * Set all MPROTx to be non-bufferable, trusted for R/W,
+	 * not forced to user-mode.
+	 */
+	ldr r0, =AIPS1_BASE_ADDR
+	ldr r1, =AIPS_MPR_CONFIG
+	str r1, [r0, #0x00]
+	str r1, [r0, #0x04]
+	ldr r0, =AIPS2_BASE_ADDR
+	str r1, [r0, #0x00]
+	str r1, [r0, #0x04]
+
+	/*
+	 * Clear the on and off peripheral modules Supervisor Protect bit
+	 * for SDMA to access them. Did not change the AIPS control registers
+	 * (offset 0x20) access type
+	 */
+	ldr r0, =AIPS1_BASE_ADDR
+	ldr r1, =AIPS_OPACR_CONFIG
+	str r1, [r0, #0x40]
+	str r1, [r0, #0x44]
+	str r1, [r0, #0x48]
+	str r1, [r0, #0x4C]
+	str r1, [r0, #0x50]
+	ldr r0, =AIPS2_BASE_ADDR
+	str r1, [r0, #0x40]
+	str r1, [r0, #0x44]
+	str r1, [r0, #0x48]
+	str r1, [r0, #0x4C]
+	str r1, [r0, #0x50]
+.endm
+
+/* MAX (Multi-Layer AHB Crossbar Switch) setup */
+.macro init_max
+	ldr r0, =MAX_BASE_ADDR
+	/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
+	ldr r1, =MAX_MPR_CONFIG
+	str r1, [r0, #0x000]        /* for S0 */
+	str r1, [r0, #0x100]        /* for S1 */
+	str r1, [r0, #0x200]        /* for S2 */
+	str r1, [r0, #0x300]        /* for S3 */
+	str r1, [r0, #0x400]        /* for S4 */
+	/* SGPCR - always park on last master */
+	ldr r1, =MAX_SGPCR_CONFIG
+	str r1, [r0, #0x010]        /* for S0 */
+	str r1, [r0, #0x110]        /* for S1 */
+	str r1, [r0, #0x210]        /* for S2 */
+	str r1, [r0, #0x310]        /* for S3 */
+	str r1, [r0, #0x410]        /* for S4 */
+	/* MGPCR - restore default values */
+	ldr r1, =MAX_MGPCR_CONFIG
+	str r1, [r0, #0x800]        /* for M0 */
+	str r1, [r0, #0x900]        /* for M1 */
+	str r1, [r0, #0xA00]        /* for M2 */
+	str r1, [r0, #0xB00]        /* for M3 */
+	str r1, [r0, #0xC00]        /* for M4 */
+	str r1, [r0, #0xD00]        /* for M5 */
+.endm
+
+/* M3IF setup */
+.macro init_m3if
+	/* Configure M3IF registers */
+	ldr r1, =M3IF_BASE_ADDR
+	/*
+	* M3IF Control Register (M3IFCTL)
+	* MRRP[0] = L2CC0 not on priority list (0 << 0)	= 0x00000000
+	* MRRP[1] = L2CC1 not on priority list (0 << 0)	= 0x00000000
+	* MRRP[2] = MBX not on priority list (0 << 0)	= 0x00000000
+	* MRRP[3] = MAX1 not on priority list (0 << 0)	= 0x00000000
+	* MRRP[4] = SDMA not on priority list (0 << 0)	= 0x00000000
+	* MRRP[5] = MPEG4 not on priority list (0 << 0)	= 0x00000000
+	* MRRP[6] = IPU1 on priority list (1 << 6)	= 0x00000040
+	* MRRP[7] = IPU2 not on priority list (0 << 0)	= 0x00000000
+	*						------------
+	*						  0x00000040
+	*/
+	ldr r0, =M3IF_CONFIG
+	str r0, [r1]  /* M3IF control reg */
+.endm
+
+/* CPLD on CS5 setup */
+.macro init_debug_board
+	ldr r0, =DBG_BASE_ADDR
+	ldr r1, =DBG_CSCR_U_CONFIG
+	str r1, [r0, #0x00]
+	ldr r1, =DBG_CSCR_L_CONFIG
+	str r1, [r0, #0x04]
+	ldr r1, =DBG_CSCR_A_CONFIG
+	str r1, [r0, #0x08]
+.endm
+
+/* clock setup */
+.macro init_clock
+	ldr r0, =CCM_BASE_ADDR
+
+	/* default CLKO to 1/32 of the ARM core*/
+	ldr r1, [r0, #CLKCTL_COSR]
+	bic r1, r1, #0x00000FF00
+	bic r1, r1, #0x0000000FF
+	mov r2, #0x00006C00
+	add r2, r2, #0x67
+	orr r1, r1, r2
+	str r1, [r0, #CLKCTL_COSR]
+
+	ldr r2, =CCM_CCMR_CONFIG
+	str r2, [r0, #CLKCTL_CCMR]
+
+	check_soc_version r1, r2
+	cmp r1, #CHIP_REV_2_0
+	ldrhs r3, =CCM_MPLL_532_HZ
+	bhs 1f
+	ldr r2, [r0, #CLKCTL_PDR0]
+	tst r2, #CLKMODE_CONSUMER
+	ldrne r3, =CCM_MPLL_532_HZ  /* consumer path*/
+	ldreq r3, =CCM_MPLL_399_HZ  /* auto path*/
+1:
+	str r3, [r0, #CLKCTL_MPCTL]
+
+	ldr r1, =CCM_PPLL_300_HZ
+	str r1, [r0, #CLKCTL_PPCTL]
+
+	ldr r1, =CCM_PDR0_CONFIG
+	bic r1, r1, #0x800000
+	str r1, [r0, #CLKCTL_PDR0]
+
+	ldr r1, [r0, #CLKCTL_CGR0]
+	orr r1, r1, #0x0C300000
+	str r1, [r0, #CLKCTL_CGR0]
+
+	ldr r1, [r0, #CLKCTL_CGR1]
+	orr r1, r1, #0x00000C00
+	orr r1, r1, #0x00000003
+	str r1, [r0, #CLKCTL_CGR1]
+.endm
+
+.macro setup_sdram
+	ldr r0, =ESDCTL_BASE_ADDR
+	mov r3, #0x2000
+	str r3, [r0, #0x0]
+	str r3, [r0, #0x8]
+
+	/*ip(r12) has used to save lr register in upper calling*/
+	mov fp, lr
+
+	mov r5, #0x00
+	mov r2, #0x00
+	mov r1, #CSD0_BASE_ADDR
+	bl setup_sdram_bank
+	cmp r3, #0x0
+	orreq r5, r5, #1
+	eorne r2, r2, #0x1
+	blne setup_sdram_bank
+
+	mov lr, fp
+
+1:
+	ldr r3, =ESDCTL_DELAY_LINE5
+	str r3, [r0, #0x30]
+.endm
+
+.globl lowlevel_init
+lowlevel_init:
+	mov r10, lr
+
+	mrc 15, 0, r1, c1, c0, 0
+
+	mrc 15, 0, r0, c1, c0, 1
+	orr r0, r0, #7
+	mcr 15, 0, r0, c1, c0, 1
+	orr r1, r1, #(1<<11)
+
+	/* Set unaligned access enable */
+	orr r1, r1, #(1<<22)
+
+	/* Set low int latency enable */
+	orr r1, r1, #(1<<21)
+
+	mcr 15, 0, r1, c1, c0, 0
+
+	mov r0, #0
+
+	/* Set branch prediction enable */
+	mcr 15, 0, r0, c15, c2, 4
+
+	mcr 15, 0, r0, c7, c7, 0        /* invalidate I cache and D cache */
+	mcr 15, 0, r0, c8, c7, 0        /* invalidate TLBs */
+	mcr 15, 0, r0, c7, c10, 4       /* Drain the write buffer */
+
+	/*
+	 * initializes very early AIPS
+	 * Then it also initializes Multi-Layer AHB Crossbar Switch,
+	 * M3IF
+	 * Also setup the Peripheral Port Remap register inside the core
+	 */
+	ldr r0, =0x40000015        /* start from AIPS 2GB region */
+	mcr p15, 0, r0, c15, c2, 4
+
+	init_aips
+
+	init_max
+
+	init_m3if
+
+	init_clock
+	init_debug_board
+
+	cmp pc, #PHYS_SDRAM_1
+	blo init_sdram_start
+	cmp pc, #(PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE)
+	blo skip_sdram_setup
+
+init_sdram_start:
+	/*init_sdram*/
+	setup_sdram
+
+skip_sdram_setup:
+	mov lr, r10
+	mov pc, lr
+
+
+/*
+ * r0: ESDCTL control base, r1: sdram slot base
+ * r2: DDR type(0:DDR2, 1:MDDR) r3, r4:working base
+ */
+setup_sdram_bank:
+	mov r3, #0xE
+	tst r2, #0x1
+	orreq r3, r3, #0x300 /*DDR2*/
+	str r3, [r0, #0x10]
+	bic r3, r3, #0x00A
+	str r3, [r0, #0x10]
+	beq 2f
+
+	mov r3, #0x20000
+1:      subs r3, r3, #1
+	bne 1b
+
+2:      tst r2, #0x1
+	ldreq r3, =ESDCTL_DDR2_CONFIG
+	ldrne r3, =ESDCTL_MDDR_CONFIG
+	cmp r1, #CSD1_BASE_ADDR
+	strlo r3, [r0, #0x4]
+	strhs r3, [r0, #0xC]
+
+	ldr r3, =ESDCTL_0x92220000
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+	mov r3, #0xDA
+	ldr r4, =ESDCTL_PRECHARGE
+	strb r3, [r1, r4]
+
+	tst r2, #0x1
+	bne skip_set_mode
+
+	cmp r1, #CSD1_BASE_ADDR
+	ldr r3, =ESDCTL_0xB2220000
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+	mov r3, #0xDA
+	ldr r4, =ESDCTL_DDR2_EMR2
+	strb r3, [r1, r4]
+	ldr r4, =ESDCTL_DDR2_EMR3
+	strb r3, [r1, r4]
+	ldr r4, =ESDCTL_DDR2_EN_DLL
+	strb r3, [r1, r4]
+	ldr r4, =ESDCTL_DDR2_RESET_DLL
+	strb r3, [r1, r4]
+
+	ldr r3, =ESDCTL_0x92220000
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+	mov r3, #0xDA
+	ldr r4, =ESDCTL_PRECHARGE
+	strb r3, [r1, r4]
+
+skip_set_mode:
+	cmp r1, #CSD1_BASE_ADDR
+	ldr r3, =ESDCTL_0xA2220000
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+	mov r3, #0xDA
+	strb r3, [r1]
+	strb r3, [r1]
+
+	ldr r3, =ESDCTL_0xB2220000
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+	tst r2, #0x1
+	ldreq r4, =ESDCTL_DDR2_MR
+	ldrne r4, =ESDCTL_MDDR_MR
+	mov r3, #0xDA
+	strb r3, [r1, r4]
+	ldreq r4, =ESDCTL_DDR2_OCD_DEFAULT
+	streqb r3, [r1, r4]
+	ldreq r4, =ESDCTL_DDR2_EN_DLL
+	ldrne r4, =ESDCTL_MDDR_EMR
+	strb r3, [r1, r4]
+
+	cmp r1, #CSD1_BASE_ADDR
+	ldr r3, =ESDCTL_0x82228080
+	strlo r3, [r0, #0x0]
+	strhs r3, [r0, #0x8]
+
+	tst r2, #0x1
+	moveq r4, #0x20000
+	movne r4, #0x200
+1:      subs r4, r4, #1
+	bne 1b
+
+	str r3, [r1, #0x100]
+	ldr r4, [r1, #0x100]
+	cmp r3, r4
+	movne r3, #1
+	moveq r3, #0
+
+	mov pc, lr