am33xx: Update DT files, add am335x_gp_evm_config target

- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
  via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
  also enabled really.  We can just push GPIO to coming from DT

Signed-off-by: Tom Rini <trini@konsulko.com>

9 files changed, 2142 insertions, 206 deletions

diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
index 377c611eb61..a1cb4ecf578 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -38,45 +38,22 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_DM_GPIO
-static const struct omap_gpio_platdata am33xx_gpio[] = {
-	{ 0, AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
-	{ 1, AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
-	{ 2, AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
-	{ 3, AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
-#ifdef CONFIG_AM43XX
-	{ 4, AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
-	{ 5, AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
-#endif
-};
-
-U_BOOT_DEVICES(am33xx_gpios) = {
-	{ "gpio_omap", &am33xx_gpio[0] },
-	{ "gpio_omap", &am33xx_gpio[1] },
-	{ "gpio_omap", &am33xx_gpio[2] },
-	{ "gpio_omap", &am33xx_gpio[3] },
-#ifdef CONFIG_AM43XX
-	{ "gpio_omap", &am33xx_gpio[4] },
-	{ "gpio_omap", &am33xx_gpio[5] },
-#endif
-};
-
-# ifndef CONFIG_OF_CONTROL
+#if defined(CONFIG_DM_SERIAL) && !defined(CONFIG_OF_CONTROL)
 /*
  * TODO(sjg@chromium.org): When we can move SPL serial to DM, we can remove
  * the CONFIGs. At the same time, we should move this to the board files.
  */
 static const struct ns16550_platdata am33xx_serial[] = {
 	{ CONFIG_SYS_NS16550_COM1, 2, CONFIG_SYS_NS16550_CLK },
-#  ifdef CONFIG_SYS_NS16550_COM2
+# ifdef CONFIG_SYS_NS16550_COM2
 	{ CONFIG_SYS_NS16550_COM2, 2, CONFIG_SYS_NS16550_CLK },
-#   ifdef CONFIG_SYS_NS16550_COM3
+#  ifdef CONFIG_SYS_NS16550_COM3
 	{ CONFIG_SYS_NS16550_COM3, 2, CONFIG_SYS_NS16550_CLK },
 	{ CONFIG_SYS_NS16550_COM4, 2, CONFIG_SYS_NS16550_CLK },
 	{ CONFIG_SYS_NS16550_COM5, 2, CONFIG_SYS_NS16550_CLK },
 	{ CONFIG_SYS_NS16550_COM6, 2, CONFIG_SYS_NS16550_CLK },
-#   endif
 #  endif
+# endif
 };
 
 U_BOOT_DEVICES(am33xx_uarts) = {
@@ -91,10 +68,10 @@ U_BOOT_DEVICES(am33xx_uarts) = {
 #   endif
 #  endif
 };
-# endif
+#endif
 
-#else
 
+#ifndef CONFIG_DM_GPIO
 static const struct gpio_bank gpio_bank_am33xx[] = {
 	{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
 	{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
@@ -107,7 +84,6 @@ static const struct gpio_bank gpio_bank_am33xx[] = {
 };
 
 const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
-
 #endif
 
 #if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3aaeb6a53cf..ef71ac1ca50 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -52,7 +52,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
 	zynq-zc770-xm011.dtb \
 	zynq-zc770-xm012.dtb \
 	zynq-zc770-xm013.dtb
-dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
+dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb am335x-evm.dtb
 
 dtb-$(CONFIG_ARCH_SOCFPGA) +=				\
 	socfpga_arria5_socdk.dtb			\
diff --git a/arch/arm/dts/am335x-bone-common.dtsi b/arch/arm/dts/am335x-bone-common.dtsi
index e70b4d1f1fa..fec78349c1f 100644
--- a/arch/arm/dts/am335x-bone-common.dtsi
+++ b/arch/arm/dts/am335x-bone-common.dtsi
@@ -7,13 +7,6 @@
  */
 
 / {
-	model = "TI AM335x BeagleBone";
-	compatible = "ti,am335x-bone", "ti,am33xx";
-
-	chosen {
-		stdout-path = &uart0;
-	};
-
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&dcdc2_reg>;
@@ -25,184 +18,299 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	leds {
 		pinctrl-names = "default";
-		pinctrl-0 = <&clkout2_pin>;
-
-		user_leds_s0: user_leds_s0 {
-			pinctrl-single,pins = <
-				0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
-				0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a6.gpio1_22 */
-				0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
-				0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a8.gpio1_24 */
-			>;
-		};
+		pinctrl-0 = <&user_leds_s0>;
 
-		i2c0_pins: pinmux_i2c0_pins {
-			pinctrl-single,pins = <
-				0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
-				0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
-			>;
-		};
+		compatible = "gpio-leds";
 
-		uart0_pins: pinmux_uart0_pins {
-			pinctrl-single,pins = <
-				0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
-				0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
-			>;
+		led@2 {
+			label = "beaglebone:green:heartbeat";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
 		};
 
-		clkout2_pin: pinmux_clkout2_pin {
-			pinctrl-single,pins = <
-				0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr1.clkout2 */
-			>;
+		led@3 {
+			label = "beaglebone:green:mmc0";
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
 		};
 
-		cpsw_default: cpsw_default {
-			pinctrl-single,pins = <
-				/* Slave 1 */
-				0x110 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxerr.mii1_rxerr */
-				0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txen.mii1_txen */
-				0x118 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxdv.mii1_rxdv */
-				0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd3.mii1_txd3 */
-				0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd2.mii1_txd2 */
-				0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd1.mii1_txd1 */
-				0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd0.mii1_txd0 */
-				0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_txclk.mii1_txclk */
-				0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxclk.mii1_rxclk */
-				0x134 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd3.mii1_rxd3 */
-				0x138 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd2.mii1_rxd2 */
-				0x13c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd1.mii1_rxd1 */
-				0x140 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd0.mii1_rxd0 */
-			>;
+		led@4 {
+			label = "beaglebone:green:usr2";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
 		};
 
-		cpsw_sleep: cpsw_sleep {
-			pinctrl-single,pins = <
-				/* Slave 1 reset value */
-				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-			>;
+		led@5 {
+			label = "beaglebone:green:usr3";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
 		};
+	};
 
-		davinci_mdio_default: davinci_mdio_default {
-			pinctrl-single,pins = <
-				/* MDIO */
-				0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
-				0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
-			>;
-		};
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
 
-		davinci_mdio_sleep: davinci_mdio_sleep {
-			pinctrl-single,pins = <
-				/* MDIO reset value */
-				0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-				0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
-			>;
-		};
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clkout2_pin>;
+
+	user_leds_s0: user_leds_s0 {
+		pinctrl-single,pins = <
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a6.gpio1_22 */
+			0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+			0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a8.gpio1_24 */
+		>;
 	};
 
-	ocp {
-		uart0: serial@44e09000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins>;
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
 
-			status = "okay";
-		};
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
+			0x17c (PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
+		>;
+	};
 
-		musb: usb@47400000 {
-			status = "okay";
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
 
-			control@44e10000 {
-				status = "okay";
-			};
+	clkout2_pin: pinmux_clkout2_pin {
+		pinctrl-single,pins = <
+			0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr1.clkout2 */
+		>;
+	};
 
-			usb-phy@47401300 {
-				status = "okay";
-			};
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x110 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxerr.mii1_rxerr */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txen.mii1_txen */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxdv.mii1_rxdv */
+			0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd3.mii1_txd3 */
+			0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd2.mii1_txd2 */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd1.mii1_txd1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd0.mii1_txd0 */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_txclk.mii1_txclk */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxclk.mii1_rxclk */
+			0x134 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd3.mii1_rxd3 */
+			0x138 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd2.mii1_rxd2 */
+			0x13c (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd1.mii1_rxd1 */
+			0x140 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd0.mii1_rxd0 */
+		>;
+	};
 
-			usb-phy@47401b00 {
-				status = "okay";
-			};
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
 
-			usb@47401000 {
-				status = "okay";
-			};
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
 
-			usb@47401800 {
-				status = "okay";
-				dr_mode = "host";
-			};
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
 
-			dma-controller@07402000  {
-				status = "okay";
-			};
-		};
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+		>;
+	};
+
+	emmc_pins: pinmux_emmc_pins {
+		pinctrl-single,pins = <
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
 
-		i2c0: i2c@44e0b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
 
-			status = "okay";
-			clock-frequency = <400000>;
+&usb {
+	status = "okay";
+};
 
-			tps: tps@24 {
-				reg = <0x24>;
-			};
+&usb_ctrl_mod {
+	status = "okay";
+};
 
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@24 {
+		reg = <0x24>;
+	};
+
+	baseboard_eeprom: baseboard_eeprom@50 {
+		compatible = "at,24c256";
+		reg = <0x50>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		baseboard_data: baseboard_data@0 {
+			reg = <0 0x100>;
 		};
 	};
+};
 
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 
-		compatible = "gpio-leds";
+	status = "okay";
+	clock-frequency = <100000>;
 
-		led@2 {
-			label = "beaglebone:green:heartbeat";
-			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
+	cape_eeprom0: cape_eeprom0@54 {
+		compatible = "at,24c256";
+		reg = <0x54>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape0_data: cape_data@0 {
+			reg = <0 0x100>;
 		};
+	};
 
-		led@3 {
-			label = "beaglebone:green:mmc0";
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
+	cape_eeprom1: cape_eeprom1@55 {
+		compatible = "at,24c256";
+		reg = <0x55>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape1_data: cape_data@0 {
+			reg = <0 0x100>;
 		};
+	};
 
-		led@4 {
-			label = "beaglebone:green:usr2";
-			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
+	cape_eeprom2: cape_eeprom2@56 {
+		compatible = "at,24c256";
+		reg = <0x56>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape2_data: cape_data@0 {
+			reg = <0 0x100>;
 		};
+	};
 
-		led@5 {
-			label = "beaglebone:green:usr3";
-			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
+	cape_eeprom3: cape_eeprom3@57 {
+		compatible = "at,24c256";
+		reg = <0x57>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape3_data: cape_data@0 {
+			reg = <0 0x100>;
 		};
 	};
 };
 
+
 /include/ "tps65217.dtsi"
 
 &tps {
+	/*
+	 * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only
+	 * mode") at poweroff.  Most BeagleBone versions do not support RTC-only
+	 * mode and risk hardware damage if this mode is entered.
+	 *
+	 * For details, see linux-omap mailing list May 2015 thread
+	 *	[PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller
+	 * In particular, messages:
+	 *	http://www.spinics.net/lists/linux-omap/msg118585.html
+	 *	http://www.spinics.net/lists/linux-omap/msg118615.html
+	 *
+	 * You can override this later with
+	 *	&tps {  /delete-property/ ti,pmic-shutdown-controller;  }
+	 * if you want to use RTC-only mode and made sure you are not affected
+	 * by the hardware problems. (Tip: double-check by performing a current
+	 * measurement after shutdown: it should be less than 1 mA.)
+	 */
+	ti,pmic-shutdown-controller;
+
 	regulators {
 		dcdc1_reg: regulator@0 {
+			regulator-name = "vdds_dpr";
 			regulator-always-on;
 		};
 
@@ -225,18 +333,22 @@
 		};
 
 		ldo1_reg: regulator@3 {
+			regulator-name = "vio,vrtc,vdds";
 			regulator-always-on;
 		};
 
 		ldo2_reg: regulator@4 {
+			regulator-name = "vdd_3v3aux";
 			regulator-always-on;
 		};
 
 		ldo3_reg: regulator@5 {
+			regulator-name = "vdd_1v8";
 			regulator-always-on;
 		};
 
 		ldo4_reg: regulator@6 {
+			regulator-name = "vdd_3v3a";
 			regulator-always-on;
 		};
 	};
@@ -256,11 +368,29 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-
+	status = "okay";
 };
 
 &davinci_mdio {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+};
+
+&aes {
+	status = "okay";
+};
+
+&sham {
+	status = "okay";
 };
diff --git a/arch/arm/dts/am335x-bone.dts b/arch/arm/dts/am335x-bone.dts
new file mode 100644
index 00000000000..81441cc8234
--- /dev/null
+++ b/arch/arm/dts/am335x-bone.dts
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+
+/ {
+	model = "TI AM335x BeagleBone";
+	compatible = "ti,am335x-bone", "ti,am33xx";
+	chosen {
+		stdout-path = &uart0;
+	};
+};
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&ldo3_reg>;
+};
diff --git a/arch/arm/dts/am335x-boneblack.dts b/arch/arm/dts/am335x-boneblack.dts
index 197cadf72d2..679248aa022 100644
--- a/arch/arm/dts/am335x-boneblack.dts
+++ b/arch/arm/dts/am335x-boneblack.dts
@@ -10,8 +10,80 @@
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 
+/ {
+	model = "TI AM335x BeagleBone Black";
+	compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+	chosen {
+		stdout-path = &uart0;
+	};
+};
+
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+			0xa0 0x08       /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa4 0x08       /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa8 0x08       /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xac 0x08       /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb0 0x08       /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb4 0x08       /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb8 0x08       /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xbc 0x08       /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc0 0x08       /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc4 0x08       /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc8 0x08       /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xcc 0x08       /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd0 0x08       /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd4 0x08       /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd8 0x08       /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xdc 0x08       /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xe0 0x00       /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe4 0x00       /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe8 0x00       /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xec 0x00       /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+/ {
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+		status = "okay";
+	};
+};
+
+&rtc {
+	system-power-controller;
+};
diff --git a/arch/arm/dts/am335x-evm.dts b/arch/arm/dts/am335x-evm.dts
new file mode 100644
index 00000000000..e1c5d4f76c6
--- /dev/null
+++ b/arch/arm/dts/am335x-evm.dts
@@ -0,0 +1,765 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM335x EVM";
+	compatible = "ti,am335x-evm", "ti,am33xx";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	lis3_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		/* WLAN_EN GPIO for this board - Bank1, pin16 */
+		gpio = <&gpio1 16 0>;
+
+		/* WLAN card specific delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH		/* Bank1, pin25 */
+			     &gpio1 26 GPIO_ACTIVE_HIGH		/* Bank1, pin26 */
+			     &gpio1 27 GPIO_ACTIVE_HIGH>;	/* Bank1, pin27 */
+
+		col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH		/* Bank1, pin21 */
+			     &gpio1 22 GPIO_ACTIVE_HIGH>;	/* Bank1, pin22 */
+
+		linux,keymap = <0x0000008b	/* MENU */
+				0x0100009e	/* BACK */
+				0x02000069	/* LEFT */
+				0x0001006a	/* RIGHT */
+				0x0101001c	/* ENTER */
+				0x0201006c>;	/* DOWN */
+	};
+
+	gpio_keys: volume_keys@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		switch@9 {
+			label = "volume-up";
+			linux,code = <115>;
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+
+		switch@10 {
+			label = "volume-down";
+			linux,code = <114>;
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	panel {
+		compatible = "ti,tilcdc,panel";
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins_s0>;
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <32>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+
+		display-timings {
+			800x480p62 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <39>;
+				hback-porch = <39>;
+				hsync-len = <47>;
+				vback-porch = <29>;
+				vfront-porch = <13>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVM";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+
+	matrix_keypad_s0: matrix_keypad_s0 {
+		pinctrl-single,pins = <
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a6.gpio1_22 */
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a9.gpio1_25 */
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a10.gpio1_26 */
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a11.gpio1_27 */
+		>;
+	};
+
+	volume_keys_s0: volume_keys_s0 {
+		pinctrl-single,pins = <
+			0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* spi0_sclk.gpio0_2 */
+			0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* spi0_d0.gpio0_3 */
+		>;
+	};
+
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x158 (PIN_INPUT_PULLUP | MUX_MODE2)	/* spi0_d1.i2c1_sda */
+			0x15c (PIN_INPUT_PULLUP | MUX_MODE2)	/* spi0_cs0.i2c1_scl */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
+			0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
+			0x180 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+		>;
+	};
+
+	clkout2_pin: pinmux_clkout2_pin {
+		pinctrl-single,pins = <
+			0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr1.clkout2 */
+		>;
+	};
+
+	nandflash_pins_s0: nandflash_pins_s0 {
+		pinctrl-single,pins = <
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 0x0	/* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
+			0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd3.rgmii1_td3 */
+			0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd2.rgmii1_td2 */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
+			0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxclk.rgmii1_rclk */
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd3.rgmii1_rd3 */
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd2.rgmii1_rd2 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			0x44 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */
+			0x48 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */
+			0x4C (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */
+			0x78 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */
+			0x88 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */
+			0x8C (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */
+		>;
+	};
+
+	wlan_pins: pinmux_wlan_pins {
+		pinctrl-single,pins = <
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.gpio1_16 */
+			0x19C (PIN_INPUT | MUX_MODE7)		/* mcasp0_ahclkr.gpio3_17 */
+			0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* mcasp0_ahclkx.gpio3_21 */
+		>;
+	};
+
+	lcd_pins_s0: lcd_pins_s0 {
+		pinctrl-single,pins = <
+			0x20 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad8.lcd_data23 */
+			0x24 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad9.lcd_data22 */
+			0x28 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad10.lcd_data21 */
+			0x2c (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad11.lcd_data20 */
+			0x30 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad12.lcd_data19 */
+			0x34 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad13.lcd_data18 */
+			0x38 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad14.lcd_data17 */
+			0x3c (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad15.lcd_data16 */
+			0xa0 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data0.lcd_data0 */
+			0xa4 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data1.lcd_data1 */
+			0xa8 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data2.lcd_data2 */
+			0xac (PIN_OUTPUT | MUX_MODE0)		/* lcd_data3.lcd_data3 */
+			0xb0 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data4.lcd_data4 */
+			0xb4 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data5.lcd_data5 */
+			0xb8 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data6.lcd_data6 */
+			0xbc (PIN_OUTPUT | MUX_MODE0)		/* lcd_data7.lcd_data7 */
+			0xc0 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data8.lcd_data8 */
+			0xc4 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data9.lcd_data9 */
+			0xc8 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data10.lcd_data10 */
+			0xcc (PIN_OUTPUT | MUX_MODE0)		/* lcd_data11.lcd_data11 */
+			0xd0 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data12.lcd_data12 */
+			0xd4 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data13.lcd_data13 */
+			0xd8 (PIN_OUTPUT | MUX_MODE0)		/* lcd_data14.lcd_data14 */
+			0xdc (PIN_OUTPUT | MUX_MODE0)		/* lcd_data15.lcd_data15 */
+			0xe0 (PIN_OUTPUT | MUX_MODE0)		/* lcd_vsync.lcd_vsync */
+			0xe4 (PIN_OUTPUT | MUX_MODE0)		/* lcd_hsync.lcd_hsync */
+			0xe8 (PIN_OUTPUT | MUX_MODE0)		/* lcd_pclk.lcd_pclk */
+			0xec (PIN_OUTPUT | MUX_MODE0)		/* lcd_ac_bias_en.lcd_ac_bias_en */
+		>;
+	};
+
+	am335x_evm_audio_pins: am335x_evm_audio_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
+
+	dcan1_pins_default: dcan1_pins_default {
+		pinctrl-single,pins = <
+			0x168 (PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+			0x16c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	status = "okay";
+	clock-frequency = <100000>;
+
+	lis331dlh: lis331dlh@18 {
+		compatible = "st,lis331dlh", "st,lis3lv02d";
+		reg = <0x18>;
+		Vdd-supply = <&lis3_reg>;
+		Vdd_IO-supply = <&lis3_reg>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+		st,min-limit-x = <120>;
+		st,min-limit-y = <120>;
+		st,min-limit-z = <140>;
+		st,max-limit-x = <550>;
+		st,max-limit-y = <550>;
+		st,max-limit-z = <750>;
+	};
+
+	tsl2550: tsl2550@39 {
+		compatible = "taos,tsl2550";
+		reg = <0x39>;
+	};
+
+	tmp275: tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+&elm {
+	status = "okay";
+};
+
+&epwmss0 {
+	status = "okay";
+
+	ecap0: ecap@48300100 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+	};
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins_s0>;
+	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
+	nand@0,0 {
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x000020000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00020000 0x00020000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00040000 0x00020000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x00060000 0x00020000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x000C0000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x001C0000 0x00020000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001E0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x0F600000>;
+		};
+	};
+};
+
+#include "tps65910.dtsi"
+
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&am335x_evm_audio_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <32>;
+		rx-num-evt = <32>;
+};
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "rgmii-txid";
+};
+
+&tscadc {
+	status = "okay";
+	tsc {
+		ti,wires = <4>;
+		ti,x-plate-resistance = <200>;
+		ti,coordinate-readouts = <5>;
+		ti,wire-config = <0x00 0x11 0x22 0x33>;
+		ti,charge-delay = <0x400>;
+	};
+
+	adc {
+		ti,adc-channels = <4 5 6 7>;
+	};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_reg>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc3 {
+	/* these are on the crossbar and are outlined in the
+	   xbar-event-map element */
+	dmas = <&edma 12
+		&edma 13>;
+	dma-names = "tx", "rx";
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wlan_pins>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&edma {
+	ti,edma-xbar-event-map = /bits/ 16 <1 12
+					    2 13>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&dcan1 {
+	status = "disabled";	/* Enable only if Profile 1 is selected */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins_default>;
+};
diff --git a/arch/arm/dts/am33xx-clocks.dtsi b/arch/arm/dts/am33xx-clocks.dtsi
new file mode 100644
index 00000000000..afb4b3a7bab
--- /dev/null
+++ b/arch/arm/dts/am33xx-clocks.dtsi
@@ -0,0 +1,646 @@
+/*
+ * Device Tree Source for AM33xx clock data
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+&scm_clocks {
+	sys_clkin_ck: sys_clkin_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
+		ti,bit-shift = <22>;
+		reg = <0x0040>;
+	};
+
+	adc_tsc_fck: adc_tsc_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dcan0_fck: dcan0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dcan1_fck: dcan1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	mcasp0_fck: mcasp0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	mcasp1_fck: mcasp1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	smartreflex0_fck: smartreflex0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	smartreflex1_fck: smartreflex1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	sha0_fck: sha0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	aes0_fck: aes0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	rng_fck: rng_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <0>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <1>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <2>;
+		reg = <0x0664>;
+	};
+};
+&prcm_clocks {
+	clk_32768_ck: clk_32768_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	clk_rc32k_ck: clk_rc32k_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32000>;
+	};
+
+	virt_19200000_ck: virt_19200000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <19200000>;
+	};
+
+	virt_24000000_ck: virt_24000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	virt_25000000_ck: virt_25000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <25000000>;
+	};
+
+	virt_26000000_ck: virt_26000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+	};
+
+	tclkin_ck: tclkin_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
+	dpll_core_ck: dpll_core_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-core-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x0490>, <0x045c>, <0x0468>;
+	};
+
+	dpll_core_x2_ck: dpll_core_x2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-x2-clock";
+		clocks = <&dpll_core_ck>;
+	};
+
+	dpll_core_m4_ck: dpll_core_m4_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		reg = <0x0480>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_core_m5_ck: dpll_core_m5_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		reg = <0x0484>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_core_m6_ck: dpll_core_m6_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		reg = <0x04d8>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_mpu_ck: dpll_mpu_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x0488>, <0x0420>, <0x042c>;
+	};
+
+	dpll_mpu_m2_ck: dpll_mpu_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_mpu_ck>;
+		ti,max-div = <31>;
+		reg = <0x04a8>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_ddr_ck: dpll_ddr_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-no-gate-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x0494>, <0x0434>, <0x0440>;
+	};
+
+	dpll_ddr_m2_ck: dpll_ddr_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_ddr_ck>;
+		ti,max-div = <31>;
+		reg = <0x04a0>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_ddr_m2_div2_ck: dpll_ddr_m2_div2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_ddr_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	dpll_disp_ck: dpll_disp_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-no-gate-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x0498>, <0x0448>, <0x0454>;
+	};
+
+	dpll_disp_m2_ck: dpll_disp_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_disp_ck>;
+		ti,max-div = <31>;
+		reg = <0x04a4>;
+		ti,index-starts-at-one;
+		ti,set-rate-parent;
+	};
+
+	dpll_per_ck: dpll_per_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-no-gate-j-type-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x048c>, <0x0470>, <0x049c>;
+	};
+
+	dpll_per_m2_ck: dpll_per_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_per_ck>;
+		ti,max-div = <31>;
+		reg = <0x04ac>;
+		ti,index-starts-at-one;
+	};
+
+	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <4>;
+	};
+
+	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <4>;
+	};
+
+	cefuse_fck: cefuse_fck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&sys_clkin_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x0a20>;
+	};
+
+	clk_24mhz: clk_24mhz {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <8>;
+	};
+
+	clkdiv32k_ck: clkdiv32k_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&clk_24mhz>;
+		clock-mult = <1>;
+		clock-div = <732>;
+	};
+
+	clkdiv32k_ick: clkdiv32k_ick {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x014c>;
+	};
+
+	l3_gclk: l3_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	pruss_ocp_gclk: pruss_ocp_gclk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&l3_gclk>, <&dpll_disp_m2_ck>;
+		reg = <0x0530>;
+	};
+
+	mmu_fck: mmu_fck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_core_m4_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x0914>;
+	};
+
+	timer1_fck: timer1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
+		reg = <0x0528>;
+	};
+
+	timer2_fck: timer2_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x0508>;
+	};
+
+	timer3_fck: timer3_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x050c>;
+	};
+
+	timer4_fck: timer4_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x0510>;
+	};
+
+	timer5_fck: timer5_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x0518>;
+	};
+
+	timer6_fck: timer6_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x051c>;
+	};
+
+	timer7_fck: timer7_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x0504>;
+	};
+
+	usbotg_fck: usbotg_fck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_per_ck>;
+		ti,bit-shift = <8>;
+		reg = <0x047c>;
+	};
+
+	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	ieee5000_fck: ieee5000_fck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x00e4>;
+	};
+
+	wdt1_fck: wdt1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
+		reg = <0x0538>;
+	};
+
+	l4_rtc_gclk: l4_rtc_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	l4hs_gclk: l4hs_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	l3s_gclk: l3s_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	l4fw_gclk: l4fw_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	l4ls_gclk: l4ls_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	sysclk_div_ck: sysclk_div_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m5_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>;
+		reg = <0x0520>;
+	};
+
+	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>;
+		reg = <0x053c>;
+	};
+
+	gpio0_dbclk: gpio0_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&gpio0_dbclk_mux_ck>;
+		ti,bit-shift = <18>;
+		reg = <0x0408>;
+	};
+
+	gpio1_dbclk: gpio1_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <18>;
+		reg = <0x00ac>;
+	};
+
+	gpio2_dbclk: gpio2_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <18>;
+		reg = <0x00b0>;
+	};
+
+	gpio3_dbclk: gpio3_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <18>;
+		reg = <0x00b4>;
+	};
+
+	lcd_gclk: lcd_gclk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
+		reg = <0x0534>;
+		ti,set-rate-parent;
+	};
+
+	mmc_clk: mmc_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x052c>;
+	};
+
+	gfx_fck_div_ck: gfx_fck_div_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&gfx_fclk_clksel_ck>;
+		reg = <0x052c>;
+		ti,max-div = <2>;
+	};
+
+	sysclkout_pre_ck: sysclkout_pre_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
+		reg = <0x0700>;
+	};
+
+	clkout2_div_ck: clkout2_div_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&sysclkout_pre_ck>;
+		ti,bit-shift = <3>;
+		ti,max-div = <8>;
+		reg = <0x0700>;
+	};
+
+	dbg_sysclk_ck: dbg_sysclk_ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&sys_clkin_ck>;
+		ti,bit-shift = <19>;
+		reg = <0x0414>;
+	};
+
+	dbg_clka_ck: dbg_clka_ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_core_m4_ck>;
+		ti,bit-shift = <30>;
+		reg = <0x0414>;
+	};
+
+	stm_pmd_clock_mux_ck: stm_pmd_clock_mux_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
+		ti,bit-shift = <22>;
+		reg = <0x0414>;
+	};
+
+	trace_pmd_clk_mux_ck: trace_pmd_clk_mux_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
+		ti,bit-shift = <20>;
+		reg = <0x0414>;
+	};
+
+	stm_clk_div_ck: stm_clk_div_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&stm_pmd_clock_mux_ck>;
+		ti,bit-shift = <27>;
+		ti,max-div = <64>;
+		reg = <0x0414>;
+		ti,index-power-of-two;
+	};
+
+	trace_clk_div_ck: trace_clk_div_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&trace_pmd_clk_mux_ck>;
+		ti,bit-shift = <24>;
+		ti,max-div = <64>;
+		reg = <0x0414>;
+		ti,index-power-of-two;
+	};
+
+	clkout2_ck: clkout2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkout2_div_ck>;
+		ti,bit-shift = <7>;
+		reg = <0x0700>;
+	};
+};
+
+&prcm_clockdomains {
+	clk_24mhz_clkdm: clk_24mhz_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&clkdiv32k_ick>;
+	};
+};
diff --git a/arch/arm/dts/am33xx.dtsi b/arch/arm/dts/am33xx.dtsi
index f9c5da9c7fe..21fcc440fc1 100644
--- a/arch/arm/dts/am33xx.dtsi
+++ b/arch/arm/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -30,6 +33,8 @@
 		usb1 = &usb1;
 		phy0 = &usb0_phy;
 		phy1 = &usb1_phy;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
 	};
 
 	cpus {
@@ -53,12 +58,21 @@
 				275000  1125000
 			>;
 			voltage-tolerance = <2>; /* 2 percentage */
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
 			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -69,19 +83,10 @@
 		};
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
-		compatible = "pinctrl-single";
-		reg = <0x44e10800 0x0238>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-single,register-width = <32>;
-		pinctrl-single,function-mask = <0x7f>;
-	};
-
 	/*
 	 * XXX: Use a flat representation of the AM33XX interconnect.
-	 * The real AM33XX interconnect network is quite complex.Since
-	 * that will not bring real advantage to represent that in DT
+	 * The real AM33XX interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
 	 * for the moment, just use a fake OCP bus entry to represent
 	 * the whole bus hierarchy.
 	 */
@@ -92,21 +97,81 @@
 		ranges;
 		ti,hwmods = "l3_main";
 
+		l4_wkup: l4_wkup@44c00000 {
+			compatible = "ti,am3-l4-wkup", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x44c00000 0x280000>;
+
+			prcm: prcm@200000 {
+				compatible = "ti,am3-prcm";
+				reg = <0x200000 0x4000>;
+
+				prcm_clocks: clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				prcm_clockdomains: clockdomains {
+				};
+			};
+
+			scm: scm@210000 {
+				compatible = "ti,am3-scm", "simple-bus";
+				reg = <0x210000 0x2000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x210000 0x2000>;
+
+				am33xx_pinmux: pinmux@800 {
+					compatible = "pinctrl-single";
+					reg = <0x800 0x238>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					pinctrl-single,register-width = <32>;
+					pinctrl-single,function-mask = <0x7f>;
+				};
+
+				scm_conf: scm_conf@0 {
+					compatible = "syscon";
+					reg = <0x0 0x800>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					scm_clocks: clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				scm_clockdomains: clockdomains {
+				};
+			};
+		};
+
 		intc: interrupt-controller@48200000 {
-			compatible = "ti,omap2-intc";
+			compatible = "ti,am33xx-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
-			ti,intc-size = <128>;
 			reg = <0x48200000 0x1000>;
 		};
 
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x40>;
+			interrupts = <12 13 14>;
+			#dma-cells = <1>;
+		};
+
 		gpio0: gpio@44e07000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x44e07000 0x1000>;
 			interrupts = <96>;
 		};
@@ -117,7 +182,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x4804c000 0x1000>;
 			interrupts = <98>;
 		};
@@ -128,7 +193,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ac000 0x1000>;
 			interrupts = <32>;
 		};
@@ -139,7 +204,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ae000 0x1000>;
 			interrupts = <62>;
 		};
@@ -151,6 +216,8 @@
 			reg = <0x44e09000 0x2000>;
 			interrupts = <72>;
 			status = "disabled";
+			dmas = <&edma 26>, <&edma 27>;
+			dma-names = "tx", "rx";
 		};
 
 		uart1: serial@48022000 {
@@ -160,6 +227,8 @@
 			reg = <0x48022000 0x2000>;
 			interrupts = <73>;
 			status = "disabled";
+			dmas = <&edma 28>, <&edma 29>;
+			dma-names = "tx", "rx";
 		};
 
 		uart2: serial@48024000 {
@@ -169,6 +238,8 @@
 			reg = <0x48024000 0x2000>;
 			interrupts = <74>;
 			status = "disabled";
+			dmas = <&edma 30>, <&edma 31>;
+			dma-names = "tx", "rx";
 		};
 
 		uart3: serial@481a6000 {
@@ -228,6 +299,51 @@
 			status = "disabled";
 		};
 
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			ti,needs-special-hs-handling;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <64>;
+			interrupt-parent = <&intc>;
+			reg = <0x48060000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <28>;
+			interrupt-parent = <&intc>;
+			reg = <0x481d8000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <29>;
+			interrupt-parent = <&intc>;
+			reg = <0x47810000 0x1000>;
+			status = "disabled";
+		};
+
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		wdt2: wdt@44e35000 {
 			compatible = "ti,omap3-wdt";
 			ti,hwmods = "wd_timer2";
@@ -235,24 +351,42 @@
 			interrupts = <91>;
 		};
 
-		dcan0: d_can@481cc000 {
-			compatible = "bosch,d_can";
+		dcan0: can@481cc000 {
+			compatible = "ti,am3352-d_can";
 			ti,hwmods = "d_can0";
-			reg = <0x481cc000 0x2000
-				0x44e10644 0x4>;
+			reg = <0x481cc000 0x2000>;
+			clocks = <&dcan0_fck>;
+			clock-names = "fck";
+			syscon-raminit = <&scm_conf 0x644 0>;
 			interrupts = <52>;
 			status = "disabled";
 		};
 
-		dcan1: d_can@481d0000 {
-			compatible = "bosch,d_can";
+		dcan1: can@481d0000 {
+			compatible = "ti,am3352-d_can";
 			ti,hwmods = "d_can1";
-			reg = <0x481d0000 0x2000
-				0x44e10644 0x4>;
+			reg = <0x481d0000 0x2000>;
+			clocks = <&dcan1_fck>;
+			clock-names = "fck";
+			syscon-raminit = <&scm_conf 0x644 1>;
 			interrupts = <55>;
 			status = "disabled";
 		};
 
+		mailbox: mailbox@480C8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480C8000 0x200>;
+			interrupts = <77>;
+			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <8>;
+			mbox_wkupm3: wkup_m3 {
+				ti,mbox-tx = <0 0 0>;
+				ti,mbox-rx = <0 0 3>;
+			};
+		};
+
 		timer1: timer@44e31000 {
 			compatible = "ti,am335x-timer-1ms";
 			reg = <0x44e31000 0x400>;
@@ -307,8 +441,8 @@
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
-			compatible = "ti,da830-rtc";
+		rtc: rtc@44e3e000 {
+			compatible = "ti,am3352-rtc", "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
 				      76>;
@@ -323,6 +457,11 @@
 			interrupts = <65>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi0";
+			dmas = <&edma 16
+				&edma 17
+				&edma 18
+				&edma 19>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -334,6 +473,11 @@
 			interrupts = <125>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi1";
+			dmas = <&edma 42
+				&edma 43
+				&edma 44
+				&edma 45>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -346,7 +490,7 @@
 			ti,hwmods = "usb_otg_hs";
 			status = "disabled";
 
-			ctrl_mod: control@44e10000 {
+			usb_ctrl_mod: control@44e10620 {
 				compatible = "ti,am335x-usb-ctrl-module";
 				reg = <0x44e10620 0x10
 					0x44e10648 0x4>;
@@ -359,7 +503,7 @@
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb0: usb@47401000 {
@@ -407,7 +551,7 @@
 				reg = <0x47401b00 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb1: usb@47401800 {
@@ -449,7 +593,7 @@
 					"tx14", "tx15";
 			};
 
-			cppi41dma: dma-controller@07402000 {
+			cppi41dma: dma-controller@47402000 {
 				compatible = "ti,am3359-cppi41";
 				reg =  <0x47400000 0x1000
 					0x47402000 0x1000
@@ -480,6 +624,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -508,6 +654,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -536,6 +684,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
@@ -552,6 +702,8 @@
 		mac: ethernet@4a100000 {
 			compatible = "ti,cpsw";
 			ti,hwmods = "cpgmac0";
+			clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
+			clock-names = "fck", "cpts";
 			cpdma_channels = <8>;
 			ale_entries = <1024>;
 			bd_ram_size = <0x2000>;
@@ -575,6 +727,8 @@
 			 */
 			interrupts = <40 41 42 43>;
 			ranges;
+			syscon = <&scm_conf>;
+			status = "disabled";
 
 			davinci_mdio: mdio@4a101000 {
 				compatible = "ti,davinci_mdio";
@@ -583,6 +737,7 @@
 				ti,hwmods = "davinci_mdio";
 				bus_freq = <1000000>;
 				reg = <0x4a101000 0x100>;
+				status = "disabled";
 			};
 
 			cpsw_emac0: slave@4a100200 {
@@ -594,12 +749,17 @@
 				/* Filled in by U-Boot */
 				mac-address = [ 00 00 00 00 00 00 ];
 			};
+
+			phy_sel: cpsw-phy-sel@44e10650 {
+				compatible = "ti,am3352-cpsw-phy-sel";
+				reg= <0x44e10650 0x4>;
+				reg-names = "gmii-sel";
+			};
 		};
 
 		ocmcram: ocmcram@40300000 {
-			compatible = "ti,am3352-ocmcram";
-			reg = <0x40300000 0x10000>;
-			ti,hwmods = "ocmcram";
+			compatible = "mmio-sram";
+			reg = <0x40300000 0x10000>; /* 64k */
 		};
 
 		wkup_m3: wkup_m3@44d00000 {
@@ -607,6 +767,7 @@
 			reg = <0x44d00000 0x4000	/* M3 UMEM */
 			       0x44d80000 0x2000>;	/* M3 DMEM */
 			ti,hwmods = "wkup_m3";
+			ti,no-reset-on-init;
 		};
 
 		elm: elm@48080000 {
@@ -617,6 +778,15 @@
 			status = "disabled";
 		};
 
+		lcdc: lcdc@4830e000 {
+			compatible = "ti,am33xx-tilcdc";
+			reg = <0x4830e000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <36>;
+			ti,hwmods = "lcdc";
+			status = "disabled";
+		};
+
 		tscadc: tscadc@44e0d000 {
 			compatible = "ti,am3359-tscadc";
 			reg = <0x44e0d000 0x1000>;
@@ -637,6 +807,7 @@
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
 			gpmc,num-cs = <7>;
@@ -645,5 +816,61 @@
 			#size-cells = <1>;
 			status = "disabled";
 		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap4-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x200>;
+			interrupts = <109>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+		};
+
+		aes: aes@53500000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x53500000 0xa0>;
+			interrupts = <103>;
+			dmas = <&edma 6>,
+			       <&edma 5>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupt-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+				<&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupt-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+				<&edma 11>;
+			dma-names = "tx", "rx";
+		};
+
+		rng: rng@48310000 {
+			compatible = "ti,omap4-rng";
+			ti,hwmods = "rng";
+			reg = <0x48310000 0x2000>;
+			interrupts = <111>;
+		};
 	};
 };
+
+/include/ "am33xx-clocks.dtsi"
diff --git a/arch/arm/dts/tps65910.dtsi b/arch/arm/dts/tps65910.dtsi
new file mode 100644
index 00000000000..b0ac6657a17
--- /dev/null
+++ b/arch/arm/dts/tps65910.dtsi
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/tps65910.pdf
+ */
+
+&tps {
+	compatible = "ti,tps65910";
+
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vrtc_reg: regulator@0 {
+			reg = <0>;
+			regulator-compatible = "vrtc";
+		};
+
+		vio_reg: regulator@1 {
+			reg = <1>;
+			regulator-compatible = "vio";
+		};
+
+		vdd1_reg: regulator@2 {
+			reg = <2>;
+			regulator-compatible = "vdd1";
+		};
+
+		vdd2_reg: regulator@3 {
+			reg = <3>;
+			regulator-compatible = "vdd2";
+		};
+
+		vdd3_reg: regulator@4 {
+			reg = <4>;
+			regulator-compatible = "vdd3";
+		};
+
+		vdig1_reg: regulator@5 {
+			reg = <5>;
+			regulator-compatible = "vdig1";
+		};
+
+		vdig2_reg: regulator@6 {
+			reg = <6>;
+			regulator-compatible = "vdig2";
+		};
+
+		vpll_reg: regulator@7 {
+			reg = <7>;
+			regulator-compatible = "vpll";
+		};
+
+		vdac_reg: regulator@8 {
+			reg = <8>;
+			regulator-compatible = "vdac";
+		};
+
+		vaux1_reg: regulator@9 {
+			reg = <9>;
+			regulator-compatible = "vaux1";
+		};
+
+		vaux2_reg: regulator@10 {
+			reg = <10>;
+			regulator-compatible = "vaux2";
+		};
+
+		vaux33_reg: regulator@11 {
+			reg = <11>;
+			regulator-compatible = "vaux33";
+		};
+
+		vmmc_reg: regulator@12 {
+			reg = <12>;
+			regulator-compatible = "vmmc";
+		};
+
+		vbb_reg: regulator@13 {
+			reg = <13>;
+			regulator-compatible = "vbb";
+		};
+	};
+};