arm: dts: am33xx: Sync dts with Linux 4.20.0

This patch synchronizes the am33xx SoC specific files with those from
Linux 4.20.0. Hence all board maintainers of am33xx based boards are
on the cc list.
The main purpose of this patch is to prevent further diverging of the
dts files from U-Boot and those from Linux. It aims to set the stage
for the synchronization of board specific dts files. Example: I'm the
maintainer of the PDU001 board: once this patch is applied successfully
I will make changes to the board specific dts file in Linux only and
then post a patch with a copy of this exact dts file to U-Boot. This
will make U-Boot and Linux remain in sync.
The stumbling block of https://patchwork.ozlabs.org/patch/943627 was
removed by the patch https://patchwork.ozlabs.org/patch/962428 from
Lokesh Vutla (many thanks!). This omap-serial driver allows using the
Linux am33xx.dtsi file in U-Boot.
Other changes to dts and dtsi files made by this patch are mainly to
prevent _new_ warnings during the build process. Especially the warning
at pinmux@800 stating 'unnecessary #address-cells/#size-cells without
"ranges" or child "reg"' was not removed. This warning is a good example
showing the benefit of the synchronization: if it needs to be fixed it
will be fixed in Linux and ported back to U-Boot.
Buildman reports all 46 am33xx SoC based boards to build fine, with
warnings of course. Nevertheless this patch should be tested thoroughly
on as many boards as possible to prevent any collateral damage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>

9 files changed, 393 insertions, 263 deletions

diff --git a/arch/arm/dts/am335x-evm.dts b/arch/arm/dts/am335x-evm.dts
index a6f20af648a..fe272075887 100644
--- a/arch/arm/dts/am335x-evm.dts
+++ b/arch/arm/dts/am335x-evm.dts
@@ -80,8 +80,6 @@
 
 	gpio_keys: volume_keys@0 {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		switch@9 {
@@ -723,8 +721,8 @@
 &mmc3 {
 	/* these are on the crossbar and are outlined in the
 	   xbar-event-map element */
-	dmas = <&edma 12
-		&edma 13>;
+	dmas = <&edma 12 0
+		&edma 13 0>;
 	dma-names = "tx", "rx";
 	status = "okay";
 	vmmc-supply = <&wlan_en_reg>;
diff --git a/arch/arm/dts/am335x-evmsk.dts b/arch/arm/dts/am335x-evmsk.dts
index b3e9b61baeb..0767578aeeb 100644
--- a/arch/arm/dts/am335x-evmsk.dts
+++ b/arch/arm/dts/am335x-evmsk.dts
@@ -109,8 +109,6 @@
 
 	gpio_buttons: gpio_buttons@0 {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		switch@1 {
 			label = "button0";
diff --git a/arch/arm/dts/am335x-pxm2.dtsi b/arch/arm/dts/am335x-pxm2.dtsi
index 8d58cd4c917..d9243d5d3d9 100644
--- a/arch/arm/dts/am335x-pxm2.dtsi
+++ b/arch/arm/dts/am335x-pxm2.dtsi
@@ -50,8 +50,6 @@
 
 	gpio_keys: restart-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		restart0 {
diff --git a/arch/arm/dts/am335x-rut.dts b/arch/arm/dts/am335x-rut.dts
index c6cfbb8033e..a5716a929f6 100644
--- a/arch/arm/dts/am335x-rut.dts
+++ b/arch/arm/dts/am335x-rut.dts
@@ -36,8 +36,6 @@
 
 	gpio_keys: powerfail-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		pwr-fail0 {
@@ -190,12 +188,8 @@
 
 &epwmss1 {
 	status = "okay";
-
-	ehrpwm1: ehrpwm@48302200 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&epwmss1_pins>;
-	};
+	pinctrl-names = "default";
+	pinctrl-0 = <&epwmss1_pins>;
 };
 
 &gpmc {
diff --git a/arch/arm/dts/am33xx-clocks.dtsi b/arch/arm/dts/am33xx-clocks.dtsi
index afb4b3a7bab..95d5c9d136c 100644
--- a/arch/arm/dts/am33xx-clocks.dtsi
+++ b/arch/arm/dts/am33xx-clocks.dtsi
@@ -8,7 +8,7 @@
  * published by the Free Software Foundation.
  */
 &scm_clocks {
-	sys_clkin_ck: sys_clkin_ck {
+	sys_clkin_ck: sys_clkin_ck@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
@@ -163,7 +163,7 @@
 		clock-frequency = <12000000>;
 	};
 
-	dpll_core_ck: dpll_core_ck {
+	dpll_core_ck: dpll_core_ck@490 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-core-clock";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
@@ -176,7 +176,7 @@
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_m4_ck: dpll_core_m4_ck {
+	dpll_core_m4_ck: dpll_core_m4_ck@480 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_core_x2_ck>;
@@ -185,7 +185,7 @@
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m5_ck: dpll_core_m5_ck {
+	dpll_core_m5_ck: dpll_core_m5_ck@484 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_core_x2_ck>;
@@ -194,7 +194,7 @@
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m6_ck: dpll_core_m6_ck {
+	dpll_core_m6_ck: dpll_core_m6_ck@4d8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_core_x2_ck>;
@@ -203,14 +203,14 @@
 		ti,index-starts-at-one;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck {
+	dpll_mpu_ck: dpll_mpu_ck@488 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0488>, <0x0420>, <0x042c>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck {
+	dpll_mpu_m2_ck: dpll_mpu_m2_ck@4a8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_mpu_ck>;
@@ -219,14 +219,14 @@
 		ti,index-starts-at-one;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck {
+	dpll_ddr_ck: dpll_ddr_ck@494 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0494>, <0x0434>, <0x0440>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck {
+	dpll_ddr_m2_ck: dpll_ddr_m2_ck@4a0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_ddr_ck>;
@@ -243,14 +243,14 @@
 		clock-div = <2>;
 	};
 
-	dpll_disp_ck: dpll_disp_ck {
+	dpll_disp_ck: dpll_disp_ck@498 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0498>, <0x0448>, <0x0454>;
 	};
 
-	dpll_disp_m2_ck: dpll_disp_m2_ck {
+	dpll_disp_m2_ck: dpll_disp_m2_ck@4a4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_disp_ck>;
@@ -260,14 +260,14 @@
 		ti,set-rate-parent;
 	};
 
-	dpll_per_ck: dpll_per_ck {
+	dpll_per_ck: dpll_per_ck@48c {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-j-type-clock";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x048c>, <0x0470>, <0x049c>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck {
+	dpll_per_m2_ck: dpll_per_m2_ck@4ac {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&dpll_per_ck>;
@@ -292,14 +292,6 @@
 		clock-div = <4>;
 	};
 
-	cefuse_fck: cefuse_fck {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&sys_clkin_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x0a20>;
-	};
-
 	clk_24mhz: clk_24mhz {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -316,14 +308,6 @@
 		clock-div = <732>;
 	};
 
-	clkdiv32k_ick: clkdiv32k_ick {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkdiv32k_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x014c>;
-	};
-
 	l3_gclk: l3_gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -332,14 +316,14 @@
 		clock-div = <1>;
 	};
 
-	pruss_ocp_gclk: pruss_ocp_gclk {
+	pruss_ocp_gclk: pruss_ocp_gclk@530 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&l3_gclk>, <&dpll_disp_m2_ck>;
 		reg = <0x0530>;
 	};
 
-	mmu_fck: mmu_fck {
+	mmu_fck: mmu_fck@914 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
 		clocks = <&dpll_core_m4_ck>;
@@ -347,56 +331,56 @@
 		reg = <0x0914>;
 	};
 
-	timer1_fck: timer1_fck {
+	timer1_fck: timer1_fck@528 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
+		clocks = <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
 		reg = <0x0528>;
 	};
 
-	timer2_fck: timer2_fck {
+	timer2_fck: timer2_fck@508 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0508>;
 	};
 
-	timer3_fck: timer3_fck {
+	timer3_fck: timer3_fck@50c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x050c>;
 	};
 
-	timer4_fck: timer4_fck {
+	timer4_fck: timer4_fck@510 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0510>;
 	};
 
-	timer5_fck: timer5_fck {
+	timer5_fck: timer5_fck@518 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0518>;
 	};
 
-	timer6_fck: timer6_fck {
+	timer6_fck: timer6_fck@51c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x051c>;
 	};
 
-	timer7_fck: timer7_fck {
+	timer7_fck: timer7_fck@504 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0504>;
 	};
 
-	usbotg_fck: usbotg_fck {
+	usbotg_fck: usbotg_fck@47c {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
 		clocks = <&dpll_per_ck>;
@@ -412,7 +396,7 @@
 		clock-div = <2>;
 	};
 
-	ieee5000_fck: ieee5000_fck {
+	ieee5000_fck: ieee5000_fck@e4 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
 		clocks = <&dpll_core_m4_div2_ck>;
@@ -420,10 +404,10 @@
 		reg = <0x00e4>;
 	};
 
-	wdt1_fck: wdt1_fck {
+	wdt1_fck: wdt1_fck@538 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
+		clocks = <&clk_rc32k_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0538>;
 	};
 
@@ -483,53 +467,21 @@
 		clock-div = <2>;
 	};
 
-	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk {
+	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk@520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>;
 		reg = <0x0520>;
 	};
 
-	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck {
+	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck@53c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
-		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>;
+		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x053c>;
 	};
 
-	gpio0_dbclk: gpio0_dbclk {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&gpio0_dbclk_mux_ck>;
-		ti,bit-shift = <18>;
-		reg = <0x0408>;
-	};
-
-	gpio1_dbclk: gpio1_dbclk {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkdiv32k_ick>;
-		ti,bit-shift = <18>;
-		reg = <0x00ac>;
-	};
-
-	gpio2_dbclk: gpio2_dbclk {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkdiv32k_ick>;
-		ti,bit-shift = <18>;
-		reg = <0x00b0>;
-	};
-
-	gpio3_dbclk: gpio3_dbclk {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkdiv32k_ick>;
-		ti,bit-shift = <18>;
-		reg = <0x00b4>;
-	};
-
-	lcd_gclk: lcd_gclk {
+	lcd_gclk: lcd_gclk@534 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
@@ -545,7 +497,7 @@
 		clock-div = <2>;
 	};
 
-	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck {
+	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck@52c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
@@ -553,7 +505,7 @@
 		reg = <0x052c>;
 	};
 
-	gfx_fck_div_ck: gfx_fck_div_ck {
+	gfx_fck_div_ck: gfx_fck_div_ck@52c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&gfx_fclk_clksel_ck>;
@@ -561,14 +513,14 @@
 		ti,max-div = <2>;
 	};
 
-	sysclkout_pre_ck: sysclkout_pre_ck {
+	sysclkout_pre_ck: sysclkout_pre_ck@700 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
 		reg = <0x0700>;
 	};
 
-	clkout2_div_ck: clkout2_div_ck {
+	clkout2_div_ck: clkout2_div_ck@700 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
 		clocks = <&sysclkout_pre_ck>;
@@ -577,59 +529,7 @@
 		reg = <0x0700>;
 	};
 
-	dbg_sysclk_ck: dbg_sysclk_ck {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&sys_clkin_ck>;
-		ti,bit-shift = <19>;
-		reg = <0x0414>;
-	};
-
-	dbg_clka_ck: dbg_clka_ck {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll_core_m4_ck>;
-		ti,bit-shift = <30>;
-		reg = <0x0414>;
-	};
-
-	stm_pmd_clock_mux_ck: stm_pmd_clock_mux_ck {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
-		ti,bit-shift = <22>;
-		reg = <0x0414>;
-	};
-
-	trace_pmd_clk_mux_ck: trace_pmd_clk_mux_ck {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
-		ti,bit-shift = <20>;
-		reg = <0x0414>;
-	};
-
-	stm_clk_div_ck: stm_clk_div_ck {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&stm_pmd_clock_mux_ck>;
-		ti,bit-shift = <27>;
-		ti,max-div = <64>;
-		reg = <0x0414>;
-		ti,index-power-of-two;
-	};
-
-	trace_clk_div_ck: trace_clk_div_ck {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&trace_pmd_clk_mux_ck>;
-		ti,bit-shift = <24>;
-		ti,max-div = <64>;
-		reg = <0x0414>;
-		ti,index-power-of-two;
-	};
-
-	clkout2_ck: clkout2_ck {
+	clkout2_ck: clkout2_ck@700 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
 		clocks = <&clkout2_div_ck>;
@@ -638,9 +538,88 @@
 	};
 };
 
-&prcm_clockdomains {
-	clk_24mhz_clkdm: clk_24mhz_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&clkdiv32k_ick>;
+&prcm {
+	l4_per_cm: l4_per_cm@0 {
+		compatible = "ti,omap4-cm";
+		reg = <0x0 0x200>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x0 0x200>;
+
+		l4_per_clkctrl: clk@14 {
+			compatible = "ti,clkctrl";
+			reg = <0x14 0x13c>;
+			#clock-cells = <2>;
+		};
+	};
+
+	l4_wkup_cm: l4_wkup_cm@400 {
+		compatible = "ti,omap4-cm";
+		reg = <0x400 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x400 0x100>;
+
+		l4_wkup_clkctrl: clk@4 {
+			compatible = "ti,clkctrl";
+			reg = <0x4 0xd4>;
+			#clock-cells = <2>;
+		};
+	};
+
+	mpu_cm: mpu_cm@600 {
+		compatible = "ti,omap4-cm";
+		reg = <0x600 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x600 0x100>;
+
+		mpu_clkctrl: clk@4 {
+			compatible = "ti,clkctrl";
+			reg = <0x4 0x4>;
+			#clock-cells = <2>;
+		};
+	};
+
+	l4_rtc_cm: l4_rtc_cm@800 {
+		compatible = "ti,omap4-cm";
+		reg = <0x800 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x800 0x100>;
+
+		l4_rtc_clkctrl: clk@0 {
+			compatible = "ti,clkctrl";
+			reg = <0x0 0x4>;
+			#clock-cells = <2>;
+		};
+	};
+
+	gfx_l3_cm: gfx_l3_cm@900 {
+		compatible = "ti,omap4-cm";
+		reg = <0x900 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x900 0x100>;
+
+		gfx_l3_clkctrl: clk@4 {
+			compatible = "ti,clkctrl";
+			reg = <0x4 0x4>;
+			#clock-cells = <2>;
+		};
+	};
+
+	l4_cefuse_cm: l4_cefuse_cm@a00 {
+		compatible = "ti,omap4-cm";
+		reg = <0xa00 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xa00 0x100>;
+
+		l4_cefuse_clkctrl: clk@20 {
+			compatible = "ti,clkctrl";
+			reg = <0x20 0x4>;
+			#clock-cells = <2>;
+		};
 	};
 };
diff --git a/arch/arm/dts/am33xx.dtsi b/arch/arm/dts/am33xx.dtsi
index 42345375e68..d3dd6a16e70 100644
--- a/arch/arm/dts/am33xx.dtsi
+++ b/arch/arm/dts/am33xx.dtsi
@@ -10,12 +10,14 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/am33xx.h>
-
-#include "skeleton.dtsi"
+#include <dt-bindings/clock/am3.h>
 
 / {
 	compatible = "ti,am33xx";
 	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
 
 	aliases {
 		i2c0 = &i2c0;
@@ -27,14 +29,16 @@
 		serial3 = &uart3;
 		serial4 = &uart4;
 		serial5 = &uart5;
-		d_can0 = &dcan0;
-		d_can1 = &dcan1;
+		d-can0 = &dcan0;
+		d-can1 = &dcan1;
 		usb0 = &usb0;
 		usb1 = &usb1;
 		phy0 = &usb0_phy;
 		phy1 = &usb1_phy;
 		ethernet0 = &cpsw_emac0;
 		ethernet1 = &cpsw_emac1;
+		spi0 = &spi0;
+		spi1 = &spi1;
 	};
 
 	cpus {
@@ -45,19 +49,7 @@
 			device_type = "cpu";
 			reg = <0>;
 
-			/*
-			 * To consider voltage drop between PMIC and SoC,
-			 * tolerance value is reduced to 2% from 4% and
-			 * voltage value is increased as a precaution.
-			 */
-			operating-points = <
-				/* kHz    uV */
-				720000  1285000
-				600000  1225000
-				500000  1125000
-				275000  1125000
-			>;
-			voltage-tolerance = <2>; /* 2 percentage */
+			operating-points-v2 = <&cpu0_opp_table>;
 
 			clocks = <&dpll_mpu_ck>;
 			clock-names = "cpu";
@@ -66,9 +58,84 @@
 		};
 	};
 
-	pmu {
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_conf>;
+
+		/*
+		 * The three following nodes are marked with opp-suspend
+		 * because the can not be enabled simultaneously on a
+		 * single SoC.
+		 */
+		opp50-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <950000 931000 969000>;
+			opp-supported-hw = <0x06 0x0010>;
+			opp-suspend;
+		};
+
+		opp100-275000000 {
+			opp-hz = /bits/ 64 <275000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x01 0x00FF>;
+			opp-suspend;
+		};
+
+		opp100-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x06 0x0020>;
+			opp-suspend;
+		};
+
+		opp100-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		opp100-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x06 0x0040>;
+		};
+
+		opp120-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1200000 1176000 1224000>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		opp120-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1200000 1176000 1224000>;
+			opp-supported-hw = <0x06 0x0080>;
+		};
+
+		oppturbo-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1260000 1234800 1285200>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		oppturbo-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1260000 1234800 1285200>;
+			opp-supported-hw = <0x06 0x0100>;
+		};
+
+		oppnitro-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1325000 1298500 1351500>;
+			opp-supported-hw = <0x04 0x0200>;
+		};
+	};
+
+	pmu@4b000000 {
 		compatible = "arm,cortex-a8-pmu";
 		interrupts = <3>;
+		reg = <0x4b000000 0x1000000>;
+		ti,hwmods = "debugss";
 	};
 
 	/*
@@ -80,6 +147,8 @@
 		mpu {
 			compatible = "ti,omap3-mpu";
 			ti,hwmods = "mpu";
+			pm-sram = <&pm_sram_code
+				   &pm_sram_data>;
 		};
 	};
 
@@ -91,7 +160,6 @@
 	 * the whole bus hierarchy.
 	 */
 	ocp {
-		u-boot,dm-spl;
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -104,9 +172,21 @@
 			#size-cells = <1>;
 			ranges = <0 0x44c00000 0x280000>;
 
+			wkup_m3: wkup_m3@100000 {
+				compatible = "ti,am3352-wkup-m3";
+				reg = <0x100000 0x4000>,
+				      <0x180000	0x2000>;
+				reg-names = "umem", "dmem";
+				ti,hwmods = "wkup_m3";
+				ti,pm-firmware = "am335x-pm-firmware.elf";
+			};
+
 			prcm: prcm@200000 {
-				compatible = "ti,am3-prcm";
+				compatible = "ti,am3-prcm", "simple-bus";
 				reg = <0x200000 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x200000 0x4000>;
 
 				prcm_clocks: clocks {
 					#address-cells = <1>;
@@ -122,6 +202,7 @@
 				reg = <0x210000 0x2000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+				#pinctrl-cells = <1>;
 				ranges = <0 0x210000 0x2000>;
 
 				am33xx_pinmux: pinmux@800 {
@@ -129,15 +210,17 @@
 					reg = <0x800 0x238>;
 					#address-cells = <1>;
 					#size-cells = <0>;
+					#pinctrl-cells = <1>;
 					pinctrl-single,register-width = <32>;
 					pinctrl-single,function-mask = <0x7f>;
 				};
 
 				scm_conf: scm_conf@0 {
-					compatible = "syscon";
+					compatible = "syscon", "simple-bus";
 					reg = <0x0 0x800>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0 0x800>;
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -145,6 +228,22 @@
 					};
 				};
 
+				wkup_m3_ipc: wkup_m3_ipc@1324 {
+					compatible = "ti,am3352-wkup-m3-ipc";
+					reg = <0x1324 0x24>;
+					interrupts = <78>;
+					ti,rproc = <&wkup_m3>;
+					mboxes = <&mailbox &mbox_wkupm3>;
+				};
+
+				edma_xbar: dma-router@f90 {
+					compatible = "ti,am335x-edma-crossbar";
+					reg = <0xf90 0x40>;
+					#dma-cells = <3>;
+					dma-requests = <32>;
+					dma-masters = <&edma>;
+				};
+
 				scm_clockdomains: clockdomains {
 				};
 			};
@@ -158,12 +257,44 @@
 		};
 
 		edma: edma@49000000 {
-			compatible = "ti,edma3";
-			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
-			reg =	<0x49000000 0x10000>,
-				<0x44e10f90 0x40>;
+			compatible = "ti,edma3-tpcc";
+			ti,hwmods = "tpcc";
+			reg =	<0x49000000 0x10000>;
+			reg-names = "edma3_cc";
 			interrupts = <12 13 14>;
-			#dma-cells = <1>;
+			interrupt-names = "edma3_ccint", "edma3_mperr",
+					  "edma3_ccerrint";
+			dma-requests = <64>;
+			#dma-cells = <2>;
+
+			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+				   <&edma_tptc2 0>;
+
+			ti,edma-memcpy-channels = <20 21>;
+		};
+
+		edma_tptc0: tptc@49800000 {
+			compatible = "ti,edma3-tptc";
+			ti,hwmods = "tptc0";
+			reg =	<0x49800000 0x100000>;
+			interrupts = <112>;
+			interrupt-names = "edma3_tcerrint";
+		};
+
+		edma_tptc1: tptc@49900000 {
+			compatible = "ti,edma3-tptc";
+			ti,hwmods = "tptc1";
+			reg =	<0x49900000 0x100000>;
+			interrupts = <113>;
+			interrupt-names = "edma3_tcerrint";
+		};
+
+		edma_tptc2: tptc@49a00000 {
+			compatible = "ti,edma3-tptc";
+			ti,hwmods = "tptc2";
+			reg =	<0x49a00000 0x100000>;
+			interrupts = <114>;
+			interrupt-names = "edma3_tcerrint";
 		};
 
 		gpio0: gpio@44e07000 {
@@ -211,67 +342,61 @@
 		};
 
 		uart0: serial@44e09000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart1";
 			clock-frequency = <48000000>;
 			reg = <0x44e09000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <72>;
 			status = "disabled";
-			dmas = <&edma 26>, <&edma 27>;
+			dmas = <&edma 26 0>, <&edma 27 0>;
 			dma-names = "tx", "rx";
 		};
 
 		uart1: serial@48022000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart2";
 			clock-frequency = <48000000>;
 			reg = <0x48022000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <73>;
 			status = "disabled";
-			dmas = <&edma 28>, <&edma 29>;
+			dmas = <&edma 28 0>, <&edma 29 0>;
 			dma-names = "tx", "rx";
 		};
 
 		uart2: serial@48024000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart3";
 			clock-frequency = <48000000>;
 			reg = <0x48024000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <74>;
 			status = "disabled";
-			dmas = <&edma 30>, <&edma 31>;
+			dmas = <&edma 30 0>, <&edma 31 0>;
 			dma-names = "tx", "rx";
 		};
 
 		uart3: serial@481a6000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
 			reg = <0x481a6000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <44>;
 			status = "disabled";
 		};
 
 		uart4: serial@481a8000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart5";
 			clock-frequency = <48000000>;
 			reg = <0x481a8000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <45>;
 			status = "disabled";
 		};
 
 		uart5: serial@481aa000 {
-			compatible = "ti,omap3-uart";
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart6";
 			clock-frequency = <48000000>;
 			reg = <0x481aa000 0x2000>;
-			reg-shift = <2>;
 			interrupts = <46>;
 			status = "disabled";
 		};
@@ -312,8 +437,8 @@
 			ti,dual-volt;
 			ti,needs-special-reset;
 			ti,needs-special-hs-handling;
-			dmas = <&edma 24
-				&edma 25>;
+			dmas = <&edma_xbar 24 0 0
+				&edma_xbar 25 0 0>;
 			dma-names = "tx", "rx";
 			interrupts = <64>;
 			reg = <0x48060000 0x1000>;
@@ -324,8 +449,8 @@
 			compatible = "ti,omap4-hsmmc";
 			ti,hwmods = "mmc2";
 			ti,needs-special-reset;
-			dmas = <&edma 2
-				&edma 3>;
+			dmas = <&edma 2 0
+				&edma 3 0>;
 			dma-names = "tx", "rx";
 			interrupts = <28>;
 			reg = <0x481d8000 0x1000>;
@@ -377,7 +502,7 @@
 			status = "disabled";
 		};
 
-		mailbox: mailbox@480C8000 {
+		mailbox: mailbox@480c8000 {
 			compatible = "ti,omap4-mailbox";
 			reg = <0x480C8000 0x200>;
 			interrupts = <77>;
@@ -386,6 +511,7 @@
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
 			mbox_wkupm3: wkup_m3 {
+				ti,mbox-send-noirq;
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <0 0 3>;
 			};
@@ -397,6 +523,8 @@
 			interrupts = <67>;
 			ti,hwmods = "timer1";
 			ti,timer-alwon;
+			clocks = <&timer1_fck>;
+			clock-names = "fck";
 		};
 
 		timer2: timer@48040000 {
@@ -404,6 +532,8 @@
 			reg = <0x48040000 0x400>;
 			interrupts = <68>;
 			ti,hwmods = "timer2";
+			clocks = <&timer2_fck>;
+			clock-names = "fck";
 		};
 
 		timer3: timer@48042000 {
@@ -451,6 +581,8 @@
 			interrupts = <75
 				      76>;
 			ti,hwmods = "rtc";
+			clocks = <&l4_per_clkctrl AM3_CLKDIV32K_CLKCTRL 0>;
+			clock-names = "int-clk";
 		};
 
 		spi0: spi@48030000 {
@@ -461,10 +593,10 @@
 			interrupts = <65>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi0";
-			dmas = <&edma 16
-				&edma 17
-				&edma 18
-				&edma 19>;
+			dmas = <&edma 16 0
+				&edma 17 0
+				&edma 18 0
+				&edma 19 0>;
 			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
@@ -477,10 +609,10 @@
 			interrupts = <125>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi1";
-			dmas = <&edma 42
-				&edma 43
-				&edma 44
-				&edma 45>;
+			dmas = <&edma 42 0
+				&edma 43 0
+				&edma 44 0
+				&edma 45 0>;
 			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
@@ -508,6 +640,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {
@@ -556,6 +689,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb1: usb@47401800 {
@@ -625,20 +759,24 @@
 				  0x48300200 0x48300200 0x80>; /* EHRPWM */
 
 			ecap0: ecap@48300100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <31>;
 				interrupt-names = "ecap0";
-				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
 
-			ehrpwm0: ehrpwm@48300200 {
-				compatible = "ti,am33xx-ehrpwm";
+			ehrpwm0: pwm@48300200 {
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
-				ti,hwmods = "ehrpwm0";
+				clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -655,20 +793,24 @@
 				  0x48302200 0x48302200 0x80>; /* EHRPWM */
 
 			ecap1: ecap@48302100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <47>;
 				interrupt-names = "ecap1";
-				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
 
-			ehrpwm1: ehrpwm@48302200 {
-				compatible = "ti,am33xx-ehrpwm";
+			ehrpwm1: pwm@48302200 {
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
-				ti,hwmods = "ehrpwm1";
+				clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -685,34 +827,36 @@
 				  0x48304200 0x48304200 0x80>; /* EHRPWM */
 
 			ecap2: ecap@48304100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <61>;
 				interrupt-names = "ecap2";
-				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
 
-			ehrpwm2: ehrpwm@48304200 {
-				compatible = "ti,am33xx-ehrpwm";
+			ehrpwm2: pwm@48304200 {
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
-				ti,hwmods = "ehrpwm2";
+				clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
 
 		mac: ethernet@4a100000 {
-			compatible = "ti,cpsw";
+			compatible = "ti,am335x-cpsw","ti,cpsw";
 			ti,hwmods = "cpgmac0";
 			clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
 			clock-names = "fck", "cpts";
 			cpdma_channels = <8>;
 			ale_entries = <1024>;
 			bd_ram_size = <0x2000>;
-			no_bd_ram = <0>;
-			rx_descs = <64>;
 			mac_control = <0x20>;
 			slaves = <2>;
 			active_slave = <0>;
@@ -734,7 +878,7 @@
 			status = "disabled";
 
 			davinci_mdio: mdio@4a101000 {
-				compatible = "ti,davinci_mdio";
+				compatible = "ti,cpsw-mdio","ti,davinci_mdio";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				ti,hwmods = "davinci_mdio";
@@ -763,14 +907,21 @@
 		ocmcram: ocmcram@40300000 {
 			compatible = "mmio-sram";
 			reg = <0x40300000 0x10000>; /* 64k */
-		};
+			ranges = <0x0 0x40300000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-		wkup_m3: wkup_m3@44d00000 {
-			compatible = "ti,am3353-wkup-m3";
-			reg = <0x44d00000 0x4000	/* M3 UMEM */
-			       0x44d80000 0x2000>;	/* M3 DMEM */
-			ti,hwmods = "wkup_m3";
-			ti,no-reset-on-init;
+			pm_sram_code: pm-sram-code@0 {
+				compatible = "ti,sram";
+				reg = <0x0 0x1000>;
+				protect-exec;
+			};
+
+			pm_sram_data: pm-sram-data@1000 {
+				compatible = "ti,sram";
+				reg = <0x1000 0x1000>;
+				pool;
+			};
 		};
 
 		elm: elm@48080000 {
@@ -795,6 +946,8 @@
 			interrupts = <16>;
 			ti,hwmods = "adc_tsc";
 			status = "disabled";
+			dmas = <&edma 53 0>, <&edma 57 0>;
+			dma-names = "fifo0", "fifo1";
 
 			tsc {
 				compatible = "ti,am3359-tsc";
@@ -805,16 +958,32 @@
 			};
 		};
 
+		emif: emif@4c000000 {
+			compatible = "ti,emif-am3352";
+			reg = <0x4c000000 0x1000000>;
+			ti,hwmods = "emif";
+			interrupts = <101>;
+			sram = <&pm_sram_code
+				&pm_sram_data>;
+			ti,no-idle;
+		};
+
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";
 			ti,no-idle-on-init;
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
+			dmas = <&edma 52 0>;
+			dma-names = "rxtx";
 			gpmc,num-cs = <7>;
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
 			status = "disabled";
 		};
 
@@ -823,7 +992,7 @@
 			ti,hwmods = "sham";
 			reg = <0x53100000 0x200>;
 			interrupts = <109>;
-			dmas = <&edma 36>;
+			dmas = <&edma 36 0>;
 			dma-names = "rx";
 		};
 
@@ -832,8 +1001,8 @@
 			ti,hwmods = "aes";
 			reg = <0x53500000 0xa0>;
 			interrupts = <103>;
-			dmas = <&edma 6>,
-			       <&edma 5>;
+			dmas = <&edma 6 0>,
+			       <&edma 5 0>;
 			dma-names = "tx", "rx";
 		};
 
@@ -846,12 +1015,12 @@
 			interrupts = <80>, <81>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
-			dmas = <&edma 8>,
-				<&edma 9>;
+			dmas = <&edma 8 2>,
+				<&edma 9 2>;
 			dma-names = "tx", "rx";
 		};
 
-		mcasp1: mcasp@4803C000 {
+		mcasp1: mcasp@4803c000 {
 			compatible = "ti,am33xx-mcasp-audio";
 			ti,hwmods = "mcasp1";
 			reg = <0x4803C000 0x2000>,
@@ -860,8 +1029,8 @@
 			interrupts = <82>, <83>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
-			dmas = <&edma 10>,
-				<&edma 11>;
+			dmas = <&edma 10 2>,
+				<&edma 11 2>;
 			dma-names = "tx", "rx";
 		};
 
@@ -874,4 +1043,4 @@
 	};
 };
 
-/include/ "am33xx-clocks.dtsi"
+#include "am33xx-clocks.dtsi"
diff --git a/arch/arm/dts/am4372.dtsi b/arch/arm/dts/am4372.dtsi
index 3ffa8e016e0..6f60a32999a 100644
--- a/arch/arm/dts/am4372.dtsi
+++ b/arch/arm/dts/am4372.dtsi
@@ -108,8 +108,6 @@
 					compatible = "ti,am437-padconf",
 						     "pinctrl-single";
 					reg = <0x800 0x31c>;
-					#address-cells = <1>;
-					#size-cells = <0>;
 					#interrupt-cells = <1>;
 					interrupt-controller;
 					pinctrl-single,register-width = <32>;
@@ -119,8 +117,6 @@
 				scm_conf: scm_conf@0 {
 					compatible = "syscon";
 					reg = <0x0 0x800>;
-					#address-cells = <1>;
-					#size-cells = <1>;
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -764,7 +760,8 @@
 			reg = <0x48038000 0x2000>,
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <80>, <81>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8>,
@@ -778,7 +775,8 @@
 			reg = <0x4803C000 0x2000>,
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <82>, <83>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10>,
@@ -807,6 +805,8 @@
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 			status = "disabled";
 		};
 
diff --git a/arch/arm/dts/am437x-idk-evm.dts b/arch/arm/dts/am437x-idk-evm.dts
index e4546471654..28e3e1ba32a 100644
--- a/arch/arm/dts/am437x-idk-evm.dts
+++ b/arch/arm/dts/am437x-idk-evm.dts
@@ -106,8 +106,6 @@
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_pins_default>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		switch@0 {
 			label = "power-button";
diff --git a/arch/arm/dts/dm816x.dtsi b/arch/arm/dts/dm816x.dtsi
index 276211e1ee5..fe58faf2f78 100644
--- a/arch/arm/dts/dm816x.dtsi
+++ b/arch/arm/dts/dm816x.dtsi
@@ -90,8 +90,6 @@
 			dm816x_pinmux: pinmux@800 {
 				compatible = "pinctrl-single";
 				reg = <0x800 0x50a>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				#pinctrl-cells = <1>;
 				pinctrl-single,register-width = <16>;
 				pinctrl-single,function-mask = <0xf>;
@@ -127,8 +125,6 @@
 			};
 
 			scrm_clocks: clocks {
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 
 			scrm_clockdomains: clockdomains {