sunxi: Sync dts files with upstream kernel

Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.

Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

1 files changed, 29 insertions, 172 deletions

diff --git a/arch/arm/dts/sun8i-a23-polaroid-mid2809pxe04.dts b/arch/arm/dts/sun8i-a23-polaroid-mid2809pxe04.dts
index cb5daafcb7..8e8f3e0846 100644
--- a/arch/arm/dts/sun8i-a23-polaroid-mid2809pxe04.dts
+++ b/arch/arm/dts/sun8i-a23-polaroid-mid2809pxe04.dts
@@ -42,202 +42,59 @@
 
 /dts-v1/;
 #include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
 
 / {
 	model = "Polaroid MID2809PXE04 tablet";
 	compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23";
 
 	aliases {
-		serial0 = &r_uart;
+		ethernet0 = &esp8089;
 	};
 
-	backlight: backlight {
-		compatible = "pwm-backlight";
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&bl_en_pin_mid2809>;
-		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
-		default-brightness-level = <8>;
-		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
+		pinctrl-0 = <&wifi_pwrseq_pin_mid2809>;
+		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+		/* The esp8089 needs 200 ms after driving wifi-en high */
+		post-power-on-delay-ms = <200>;
 	};
 };
 
-&ehci0 {
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
+&gsl1680 {
+	compatible = "silead,gsl3670";
+	touchscreen-fw-name = "silead/gsl3670-polaroid-mid2809pxe04.fw";
+	touchscreen-size-x = <1660>;
+	touchscreen-size-y = <890>;
 	status = "okay";
 };
 
-&i2c1 {
+&mmc1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
-	status = "okay";
-};
-
-&lradc {
-	vref-supply = <&reg_vcc3v0>;
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
 	status = "okay";
 
-	button@200 {
-		label = "Volume Up";
-		linux,code = <KEY_VOLUMEUP>;
-		channel = <0>;
-		voltage = <200000>;
-	};
-
-	button@400 {
-		label = "Volume Down";
-		linux,code = <KEY_VOLUMEDOWN>;
-		channel = <0>;
-		voltage = <400000>;
+	esp8089: sdio_wifi@1 {
+		compatible = "esp,esp8089";
+		reg = <1>;
+		esp,crystal-26M-en = <2>;
 	};
 };
 
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2809>;
-	vmmc-supply = <&reg_dcdc1>;
-	bus-width = <4>;
-	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
-	cd-inverted;
-	status = "okay";
+&mmc1_pins_a {
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
 
-&pio {
-	bl_en_pin_mid2809: bl_en_pin@0 {
-		allwinner,pins = "PH6";
-		allwinner,function = "gpio_in";
+&r_pio {
+	wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin@0 {
+		allwinner,pins = "PL6";
+		allwinner,function = "gpio_out";
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
-
-	mmc0_cd_pin_mid2809: mmc0_cd_pin@0 {
-		allwinner,pins = "PB4";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-};
-
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_pins>;
-	status = "okay";
-};
-
-&r_rsb {
-	status = "okay";
-
-	axp22x: pmic@3a3 {
-		compatible = "x-powers,axp223";
-		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		eldoin-supply = <&reg_dcdc1>;
-	};
-};
-
-&r_uart {
-	pinctrl-names = "default";
-	pinctrl-0 = <&r_uart_pins_a>;
-	status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-&reg_aldo1 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-io";
-};
-
-&reg_aldo2 {
-	regulator-always-on;
-	regulator-min-microvolt = <2350000>;
-	regulator-max-microvolt = <2650000>;
-	regulator-name = "vdd-dll";
-};
-
-&reg_aldo3 {
-	regulator-always-on;
-	regulator-min-microvolt = <2700000>;
-	regulator-max-microvolt = <3300000>;
-	regulator-name = "vcc-pll-avcc";
-};
-
-&reg_dc1sw {
-	regulator-name = "vcc-lcd";
-};
-
-&reg_dc5ldo {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpus";
-};
-
-&reg_dcdc1 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-3v0";
-};
-
-&reg_dcdc2 {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-sys";
-};
-
-&reg_dcdc3 {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpu";
-};
-
-&reg_dcdc5 {
-	regulator-always-on;
-	regulator-min-microvolt = <1500000>;
-	regulator-max-microvolt = <1500000>;
-	regulator-name = "vcc-dram";
-};
-
-&reg_rtc_ldo {
-	regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
-	vcc-lcd-supply = <&reg_dc1sw>;
-};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbphy {
-	status = "okay";
 };