global: Finish CONFIG -> CFG migration

At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks.  Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

1 files changed, 12 insertions, 12 deletions

diff --git a/README b/README
index fe571f7ef0..40619ee40c 100644
--- a/README
+++ b/README
@@ -445,12 +445,12 @@ The following options need to be configured:
 		example "env grep" and "setexpr".
 
 - Watchdog:
-		CONFIG_SYS_WATCHDOG_FREQ
+		CFG_SYS_WATCHDOG_FREQ
 		Some platforms automatically call WATCHDOG_RESET()
 		from the timer interrupt handler every
-		CONFIG_SYS_WATCHDOG_FREQ interrupts. If not set by the
+		CFG_SYS_WATCHDOG_FREQ interrupts. If not set by the
 		board configuration file, a default of CONFIG_SYS_HZ/2
-		(i.e. 500) is used. Setting CONFIG_SYS_WATCHDOG_FREQ
+		(i.e. 500) is used. Setting CFG_SYS_WATCHDOG_FREQ
 		to 0 disables calling WATCHDOG_RESET() from the timer
 		interrupt.
 
@@ -523,7 +523,7 @@ The following options need to be configured:
 			CONFIG_LAN91C96_USE_32_BIT
 			Define this to enable 32 bit addressing
 
-			CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
+			CFG_SYS_DAVINCI_EMAC_PHY_COUNT
 			Define this if you have more then 3 PHYs.
 
 		CONFIG_FTGMAC100
@@ -653,7 +653,7 @@ The following options need to be configured:
 		To enable the ULPI layer support, define CONFIG_USB_ULPI and
 		CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
 		If your ULPI phy needs a different reference clock than the
-		standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
+		standard 24 MHz then you have to define CFG_ULPI_REF_CLK to
 		the appropriate value in Hz.
 
 - MMC Support:
@@ -734,7 +734,7 @@ The following options need to be configured:
 		4th and following
 		BOOTP requests:		delay 0 ... 8 sec
 
-		CONFIG_BOOTP_ID_CACHE_SIZE
+		CFG_BOOTP_ID_CACHE_SIZE
 
 		BOOTP packets are uniquely identified using a 32-bit ID. The
 		server will copy the ID from client requests to responses and
@@ -747,7 +747,7 @@ The following options need to be configured:
 		time is too long, U-Boot will retransmit requests. In order
 		to allow earlier responses to still be accepted after these
 		retransmissions, U-Boot's BOOTP client keeps a small cache of
-		IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
+		IDs. The CFG_BOOTP_ID_CACHE_SIZE controls the size of this
 		cache. The default is to keep IDs for up to four outstanding
 		requests. Increasing this will allow U-Boot to accept offers
 		from a BOOTP client in networks with unusually high latency.
@@ -832,11 +832,11 @@ The following options need to be configured:
 		status LED backend implementation. Define CONFIG_LED_STATUS_GPIO
 		to include the gpio_led driver in the U-Boot binary.
 
-		CONFIG_GPIO_LED_INVERTED_TABLE
+		CFG_GPIO_LED_INVERTED_TABLE
 		Some GPIO connected LEDs may have inverted polarity in which
 		case the GPIO high value corresponds to LED off state and
 		GPIO low value corresponds to LED on state.
-		In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
+		In such cases CFG_GPIO_LED_INVERTED_TABLE may be defined
 		with a list of GPIO LEDs that have inverted polarity.
 
 - I2C Support:
@@ -993,7 +993,7 @@ The following options need to be configured:
 		SPI EEPROM, also an instance works with Crystal A/D and
 		D/As on the SACSng board)
 
-		CONFIG_SYS_SPI_MXC_WAIT
+		CFG_SYS_SPI_MXC_WAIT
 		Timeout for waiting until spi transfer completed.
 		default: (CONFIG_SYS_HZ/100)     /* 10 ms */
 
@@ -1023,7 +1023,7 @@ The following options need to be configured:
 		If defined, a function that provides delays in the FPGA
 		configuration driver.
 
-		CONFIG_SYS_FPGA_CHECK_ERROR
+		CFG_SYS_FPGA_CHECK_ERROR
 
 		Check for configuration errors during FPGA bitfile
 		loading. For example, abort during Virtex II
@@ -1319,7 +1319,7 @@ Configuration Settings:
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
 		undefine this when you're short of memory.
 
-- CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
+- CFG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
 		width of the commands listed in the 'help' command output.
 
 - CONFIG_SYS_PROMPT:	This is what U-Boot prints on the console to