arm: rpi: Sync rpi dts files from Linux

Sync these files, obtained from Linux v5.15.

This adds a devicetree file for rpi_4 which was not there before.

Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4

I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.

Signed-off-by: Simon Glass <sjg@chromium.org>

31 files changed, 1878 insertions, 248 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2d92b2f940d..9cddab37207 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1077,7 +1077,8 @@ dtb-$(CONFIG_ARCH_BCM283X) += \
 	bcm2837-rpi-3-a-plus.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
-	bcm2837-rpi-cm3-io3.dtb
+	bcm2837-rpi-cm3-io3.dtb \
+	bcm2711-rpi-4-b.dtb
 
 dtb-$(CONFIG_ARCH_BCM63158) += \
 	bcm963158.dtb
diff --git a/arch/arm/dts/bcm2711-rpi-4-b.dts b/arch/arm/dts/bcm2711-rpi-4-b.dts
new file mode 100644
index 00000000000..72ce80fbf26
--- /dev/null
+++ b/arch/arm/dts/bcm2711-rpi-4-b.dts
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-usb-peripheral.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
+	model = "Raspberry Pi 4 Model B";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	leds {
+		led-act {
+			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	sd_io_1v8_reg: sd_io_1v8_reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: sd_vcc_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",
+			  "SD_PWR_ON",
+			  "";
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	status = "okay";
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
+&pcie0 {
+	pci@0,0 {
+		device_type = "pci";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		reg = <0 0 0 0 0>;
+
+		usb@0,0 {
+			reg = <0 0 0 0 0>;
+			resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>;
+		};
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
diff --git a/arch/arm/dts/bcm2711-rpi.dtsi b/arch/arm/dts/bcm2711-rpi.dtsi
new file mode 100644
index 00000000000..ca266c5d9f9
--- /dev/null
+++ b/arch/arm/dts/bcm2711-rpi.dtsi
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+
+/ {
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		emmc2bus = &emmc2bus;
+		ethernet0 = &genet;
+		pcie0 = &pcie0;
+		blconfig = &blconfig;
+	};
+};
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+
+	reset: reset {
+		compatible = "raspberrypi,firmware-reset";
+		#reset-cells = <1>;
+	};
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>;
+};
+
+&rmem {
+	/*
+	 * RPi4's co-processor will copy the board's bootloader configuration
+	 * into memory for the OS to consume. It'll also update this node with
+	 * its placement information.
+	 */
+	blconfig: nvram@0 {
+		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x0>;
+		no-map;
+		status = "disabled";
+	};
+};
+
+&vchiq {
+	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm/dts/bcm2711.dtsi b/arch/arm/dts/bcm2711.dtsi
new file mode 100644
index 00000000000..3b60297af7f
--- /dev/null
+++ b/arch/arm/dts/bcm2711.dtsi
@@ -0,0 +1,1100 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
+
+/ {
+	compatible = "brcm,bcm2711";
+
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gicv2>;
+
+	vc4: gpu {
+		compatible = "brcm,bcm2711-vc5";
+		status = "disabled";
+	};
+
+	clk_27MHz: clk-27M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <27000000>;
+		clock-output-names = "27MHz-clock";
+	};
+
+	clk_108MHz: clk-108M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <108000000>;
+		clock-output-names = "108MHz-clock";
+	};
+
+	soc {
+		/*
+		 * Defined ranges:
+		 *   Common BCM283x peripherals
+		 *   BCM2711-specific peripherals
+		 *   ARM-local peripherals
+		 */
+		ranges = <0x7e000000  0x0 0xfe000000  0x01800000>,
+			 <0x7c000000  0x0 0xfc000000  0x02000000>,
+			 <0x40000000  0x0 0xff800000  0x00800000>;
+		/* Emulate a contiguous 30-bit address range for DMA */
+		dma-ranges = <0xc0000000  0x0 0x00000000  0x40000000>;
+
+		/*
+		 * This node is the provider for the enable-method for
+		 * bringing up secondary cores.
+		 */
+		local_intc: local_intc@40000000 {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+		};
+
+		gicv2: interrupt-controller@40041000 {
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			compatible = "arm,gic-400";
+			reg =	<0x40041000 0x1000>,
+				<0x40042000 0x2000>,
+				<0x40044000 0x2000>,
+				<0x40046000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		avs_monitor: avs-monitor@7d5d2000 {
+			compatible = "brcm,bcm2711-avs-monitor",
+				     "syscon", "simple-mfd";
+			reg = <0x7d5d2000 0xf00>;
+
+			thermal: thermal {
+				compatible = "brcm,bcm2711-thermal";
+				#thermal-sensor-cells = <0>;
+			};
+		};
+
+		dma: dma@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xb00>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     /* DMA lite 7 - 10 */
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10";
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x07f5>;
+		};
+
+		pm: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>,
+			      <0x7ec11000 0x20>;
+			clocks = <&clocks BCM2835_CLOCK_V3D>,
+				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+				 <&clocks BCM2835_CLOCK_H264>,
+				 <&clocks BCM2835_CLOCK_ISP>;
+			clock-names = "v3d", "peri_image", "h264", "isp";
+			system-power-controller;
+		};
+
+		rng@7e104000 {
+			compatible = "brcm,bcm2711-rng200";
+			reg = <0x7e104000 0x28>;
+		};
+
+		uart2: serial@7e201400 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201400 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart3: serial@7e201600 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201600 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart4: serial@7e201800 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201800 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart5: serial@7e201a00 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201a00 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		spi3: spi@7e204600 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204600 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi4: spi@7e204800 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204800 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi5: spi@7e204a00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204a00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi6: spi@7e204c00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204c00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@7e205600 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205600 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@7e205800 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205800 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@7e205a00 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205a00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@7e205c00 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205c00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve0: pixelvalve@7e206000 {
+			compatible = "brcm,bcm2711-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			compatible = "brcm,bcm2711-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve2: pixelvalve@7e20a000 {
+			compatible = "brcm,bcm2711-pixelvalve2";
+			reg = <0x7e20a000 0x100>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@7e20c800 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c800 0x28>;
+			clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clock-rates = <10000000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pixelvalve4: pixelvalve@7e216000 {
+			compatible = "brcm,bcm2711-pixelvalve4";
+			reg = <0x7e216000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		hvs: hvs@7e400000 {
+			compatible = "brcm,bcm2711-hvs";
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pixelvalve3: pixelvalve@7ec12000 {
+			compatible = "brcm,bcm2711-pixelvalve3";
+			reg = <0x7ec12000 0x100>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		vec: vec@7ec13000 {
+			compatible = "brcm,bcm2711-vec";
+			reg = <0x7ec13000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		dvp: clock@7ef00000 {
+			compatible = "brcm,brcm2711-dvp";
+			reg = <0x7ef00000 0x10>;
+			clocks = <&clk_108MHz>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		aon_intr: interrupt-controller@7ef00100 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7ef00100 0x30>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		hdmi0: hdmi@7ef00700 {
+			compatible = "brcm,bcm2711-hdmi0";
+			reg = <0x7ef00700 0x300>,
+			      <0x7ef00300 0x200>,
+			      <0x7ef00f00 0x80>,
+			      <0x7ef00f80 0x80>,
+			      <0x7ef01b00 0x200>,
+			      <0x7ef01f00 0x400>,
+			      <0x7ef00200 0x80>,
+			      <0x7ef04300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 0>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <0>, <1>, <2>,
+				     <3>, <4>, <5>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			ddc = <&ddc0>;
+			dmas = <&dma 10>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc0: i2c@7ef04500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+
+		hdmi1: hdmi@7ef05700 {
+			compatible = "brcm,bcm2711-hdmi1";
+			reg = <0x7ef05700 0x300>,
+			      <0x7ef05300 0x200>,
+			      <0x7ef05f00 0x80>,
+			      <0x7ef05f80 0x80>,
+			      <0x7ef06b00 0x200>,
+			      <0x7ef06f00 0x400>,
+			      <0x7ef00280 0x80>,
+			      <0x7ef09300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			ddc = <&ddc1>;
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 1>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <8>, <7>, <6>,
+				     <9>, <10>, <11>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc1: i2c@7ef09500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+	};
+
+	/*
+	 * emmc2 has different DMA constraints based on SoC revisions. It was
+	 * moved into its own bus, so as for RPi4's firmware to update them.
+	 * The firmware will find whether the emmc2bus alias is defined, and if
+	 * so, it'll edit the dma-ranges property below accordingly.
+	 */
+	emmc2bus: emmc2bus {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
+		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;
+
+		emmc2: mmc@7e340000 {
+			compatible = "brcm,bcm2711-emmc2";
+			reg = <0x0 0x7e340000 0x100>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2711_CLOCK_EMMC2>;
+			status = "disabled";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+		/* This only applies to the ARMv7 stub */
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000d8>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e0>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e8>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000f0>;
+		};
+	};
+
+	scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>,
+			 <0x6 0x00000000  0x6 0x00000000  0x40000000>;
+
+		pcie0: pcie@7d500000 {
+			compatible = "brcm,bcm2711-pcie";
+			reg = <0x0 0x7d500000 0x9310>;
+			device_type = "pci";
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pcie", "msi";
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
+							IRQ_TYPE_LEVEL_HIGH>;
+			msi-controller;
+			msi-parent = <&pcie0>;
+
+			ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000
+				  0x0 0x04000000>;
+			/*
+			 * The wrapper around the PCIe block has a bug
+			 * preventing it from accessing beyond the first 3GB of
+			 * memory.
+			 */
+			dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
+				      0x0 0xc0000000>;
+			brcm,enable-ssc;
+		};
+
+		genet: ethernet@7d580000 {
+			compatible = "brcm,bcm2711-genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			genet_mdio: mdio@e14 {
+				compatible = "brcm,genet-mdio-v5";
+				reg = <0xe14 0x8>;
+				reg-names = "mdio";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+			};
+		};
+	};
+};
+
+&clk_osc {
+	clock-frequency = <54000000>;
+};
+
+&clocks {
+	compatible = "brcm,bcm2711-cprman";
+};
+
+&cpu_thermal {
+	coefficients = <(-487) 410040>;
+	thermal-sensors = <&thermal>;
+};
+
+&dsi0 {
+	interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&dsi1 {
+	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+	compatible = "brcm,bcm2711-dsi1";
+};
+
+&gpio {
+	compatible = "brcm,bcm2711-gpio";
+	interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+
+	gpclk0_gpio49: gpclk0_gpio49 {
+		pin-gpclk {
+			pins = "gpio49";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	gpclk1_gpio50: gpclk1_gpio50 {
+		pin-gpclk {
+			pins = "gpio50";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	gpclk2_gpio51: gpclk2_gpio51 {
+		pin-gpclk {
+			pins = "gpio51";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+
+	i2c0_gpio46: i2c0_gpio46 {
+		pin-sda {
+			function = "alt0";
+			pins = "gpio46";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt0";
+			pins = "gpio47";
+			bias-disable;
+		};
+	};
+	i2c1_gpio46: i2c1_gpio46 {
+		pin-sda {
+			function = "alt1";
+			pins = "gpio46";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt1";
+			pins = "gpio47";
+			bias-disable;
+		};
+	};
+	i2c3_gpio2: i2c3_gpio2 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio2";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio3";
+			bias-disable;
+		};
+	};
+	i2c3_gpio4: i2c3_gpio4 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio4";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio5";
+			bias-disable;
+		};
+	};
+	i2c4_gpio6: i2c4_gpio6 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio6";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio7";
+			bias-disable;
+		};
+	};
+	i2c4_gpio8: i2c4_gpio8 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio8";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio9";
+			bias-disable;
+		};
+	};
+	i2c5_gpio10: i2c5_gpio10 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio10";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio11";
+			bias-disable;
+		};
+	};
+	i2c5_gpio12: i2c5_gpio12 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio12";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio13";
+			bias-disable;
+		};
+	};
+	i2c6_gpio0: i2c6_gpio0 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio0";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio1";
+			bias-disable;
+		};
+	};
+	i2c6_gpio22: i2c6_gpio22 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio22";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio23";
+			bias-disable;
+		};
+	};
+	i2c_slave_gpio8: i2c_slave_gpio8 {
+		pins-i2c-slave {
+			pins = "gpio8",
+			       "gpio9",
+			       "gpio10",
+			       "gpio11";
+			function = "alt3";
+		};
+	};
+
+	jtag_gpio48: jtag_gpio48 {
+		pins-jtag {
+			pins = "gpio48",
+			       "gpio49",
+			       "gpio50",
+			       "gpio51",
+			       "gpio52",
+			       "gpio53";
+			function = "alt4";
+		};
+	};
+
+	mii_gpio28: mii_gpio28 {
+		pins-mii {
+			pins = "gpio28",
+			       "gpio29",
+			       "gpio30",
+			       "gpio31";
+			function = "alt4";
+		};
+	};
+	mii_gpio36: mii_gpio36 {
+		pins-mii {
+			pins = "gpio36",
+			       "gpio37",
+			       "gpio38",
+			       "gpio39";
+			function = "alt5";
+		};
+	};
+
+	pcm_gpio50: pcm_gpio50 {
+		pins-pcm {
+			pins = "gpio50",
+			       "gpio51",
+			       "gpio52",
+			       "gpio53";
+			function = "alt2";
+		};
+	};
+
+	pwm0_0_gpio12: pwm0_0_gpio12 {
+		pin-pwm {
+			pins = "gpio12";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_0_gpio18: pwm0_0_gpio18 {
+		pin-pwm {
+			pins = "gpio18";
+			function = "alt5";
+			bias-disable;
+		};
+	};
+	pwm1_0_gpio40: pwm1_0_gpio40 {
+		pin-pwm {
+			pins = "gpio40";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio13: pwm0_1_gpio13 {
+		pin-pwm {
+			pins = "gpio13";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio19: pwm0_1_gpio19 {
+		pin-pwm {
+			pins = "gpio19";
+			function = "alt5";
+			bias-disable;
+		};
+	};
+	pwm1_1_gpio41: pwm1_1_gpio41 {
+		pin-pwm {
+			pins = "gpio41";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio45: pwm0_1_gpio45 {
+		pin-pwm {
+			pins = "gpio45";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_0_gpio52: pwm0_0_gpio52 {
+		pin-pwm {
+			pins = "gpio52";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio53: pwm0_1_gpio53 {
+		pin-pwm {
+			pins = "gpio53";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+
+	rgmii_gpio35: rgmii_gpio35 {
+		pin-start-stop {
+			pins = "gpio35";
+			function = "alt4";
+		};
+		pin-rx-ok {
+			pins = "gpio36";
+			function = "alt4";
+		};
+	};
+	rgmii_irq_gpio34: rgmii_irq_gpio34 {
+		pin-irq {
+			pins = "gpio34";
+			function = "alt5";
+		};
+	};
+	rgmii_irq_gpio39: rgmii_irq_gpio39 {
+		pin-irq {
+			pins = "gpio39";
+			function = "alt4";
+		};
+	};
+	rgmii_mdio_gpio28: rgmii_mdio_gpio28 {
+		pins-mdio {
+			pins = "gpio28",
+			       "gpio29";
+			function = "alt5";
+		};
+	};
+	rgmii_mdio_gpio37: rgmii_mdio_gpio37 {
+		pins-mdio {
+			pins = "gpio37",
+			       "gpio38";
+			function = "alt4";
+		};
+	};
+
+	spi0_gpio46: spi0_gpio46 {
+		pins-spi {
+			pins = "gpio46",
+			       "gpio47",
+			       "gpio48",
+			       "gpio49";
+			function = "alt2";
+		};
+	};
+	spi2_gpio46: spi2_gpio46 {
+		pins-spi {
+			pins = "gpio46",
+			       "gpio47",
+			       "gpio48",
+			       "gpio49",
+			       "gpio50";
+			function = "alt5";
+		};
+	};
+	spi3_gpio0: spi3_gpio0 {
+		pins-spi {
+			pins = "gpio0",
+			       "gpio1",
+			       "gpio2",
+			       "gpio3";
+			function = "alt3";
+		};
+	};
+	spi4_gpio4: spi4_gpio4 {
+		pins-spi {
+			pins = "gpio4",
+			       "gpio5",
+			       "gpio6",
+			       "gpio7";
+			function = "alt3";
+		};
+	};
+	spi5_gpio12: spi5_gpio12 {
+		pins-spi {
+			pins = "gpio12",
+			       "gpio13",
+			       "gpio14",
+			       "gpio15";
+			function = "alt3";
+		};
+	};
+	spi6_gpio18: spi6_gpio18 {
+		pins-spi {
+			pins = "gpio18",
+			       "gpio19",
+			       "gpio20",
+			       "gpio21";
+			function = "alt3";
+		};
+	};
+
+	uart2_gpio0: uart2_gpio0 {
+		pin-tx {
+			pins = "gpio0";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio1";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 {
+		pin-cts {
+			pins = "gpio2";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio3";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart3_gpio4: uart3_gpio4 {
+		pin-tx {
+			pins = "gpio4";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio5";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 {
+		pin-cts {
+			pins = "gpio6";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio7";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart4_gpio8: uart4_gpio8 {
+		pin-tx {
+			pins = "gpio8";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio9";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 {
+		pin-cts {
+			pins = "gpio10";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio11";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart5_gpio12: uart5_gpio12 {
+		pin-tx {
+			pins = "gpio12";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio13";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 {
+		pin-cts {
+			pins = "gpio14";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio15";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+};
+
+&rmem {
+	#address-cells = <2>;
+};
+
+&cma {
+	/*
+	 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
+	 * that's not good enough for the BCM2711 as some devices can
+	 * only address the lower 1G of memory (ZONE_DMA).
+	 */
+	alloc-ranges = <0x0 0x00000000 0x40000000>;
+};
+
+&i2c0 {
+	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mailbox {
+	interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sdhci {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sdhost {
+	interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi {
+	interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi2 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&system_timer {
+	interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&txp {
+	interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usb {
+	interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&vec {
+	compatible = "brcm,bcm2711-vec";
+	interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm/dts/bcm2835-common.dtsi b/arch/arm/dts/bcm2835-common.dtsi
new file mode 100644
index 00000000000..c25e797b906
--- /dev/null
+++ b/arch/arm/dts/bcm2835-common.dtsi
@@ -0,0 +1,207 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations.
+ */
+
+/ {
+	interrupt-parent = <&intc>;
+
+	soc {
+		dma: dma@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     /* dma channel 11-14 share one irq */
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
+				     <1 28>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
+			compatible = "brcm,bcm2835-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_V3D>,
+				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+				 <&clocks BCM2835_CLOCK_H264>,
+				 <&clocks BCM2835_CLOCK_ISP>;
+			clock-names = "v3d", "peri_image", "h264", "isp";
+			system-power-controller;
+		};
+
+		rng@7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+			interrupts = <2 29>;
+		};
+
+		pixelvalve@7e206000 {
+			compatible = "brcm,bcm2835-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			interrupts = <2 13>; /* pwa0 */
+		};
+
+		pixelvalve@7e207000 {
+			compatible = "brcm,bcm2835-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			interrupts = <2 14>; /* pwa1 */
+		};
+
+		thermal: thermal@7e212000 {
+			compatible = "brcm,bcm2835-thermal";
+			reg = <0x7e212000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@7e805000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e805000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+		};
+
+		vec: vec@7e806000 {
+			compatible = "brcm,bcm2835-vec";
+			reg = <0x7e806000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <2 27>;
+			status = "disabled";
+		};
+
+		pixelvalve@7e807000 {
+			compatible = "brcm,bcm2835-pixelvalve2";
+			reg = <0x7e807000 0x100>;
+			interrupts = <2 10>; /* pixelvalve */
+		};
+
+		hdmi: hdmi@7e902000 {
+			compatible = "brcm,bcm2835-hdmi";
+			reg = <0x7e902000 0x600>,
+			      <0x7e808000 0x100>;
+			interrupts = <2 8>, <2 9>;
+			ddc = <&i2c2>;
+			clocks = <&clocks BCM2835_PLLH_PIX>,
+				 <&clocks BCM2835_CLOCK_HSM>;
+			clock-names = "pixel", "hdmi";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		v3d: v3d@7ec00000 {
+			compatible = "brcm,bcm2835-v3d";
+			reg = <0x7ec00000 0x1000>;
+			interrupts = <1 10>;
+		};
+
+		vc4: gpu {
+			compatible = "brcm,bcm2835-vc4";
+		};
+	};
+};
+
+&cpu_thermal {
+	thermal-sensors = <&thermal>;
+};
+
+&gpio {
+	i2c_slave_gpio18: i2c_slave_gpio18 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	jtag_gpio4: jtag_gpio4 {
+		brcm,pins = <4 5 6 12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+
+	pwm0_gpio12: pwm0_gpio12 {
+		brcm,pins = <12>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm0_gpio18: pwm0_gpio18 {
+		brcm,pins = <18>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	pwm0_gpio40: pwm0_gpio40 {
+		brcm,pins = <40>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio13: pwm1_gpio13 {
+		brcm,pins = <13>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio19: pwm1_gpio19 {
+		brcm,pins = <19>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	pwm1_gpio41: pwm1_gpio41 {
+		brcm,pins = <41>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio45: pwm1_gpio45 {
+		brcm,pins = <45>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&i2s {
+	dmas = <&dma 2>, <&dma 3>;
+	dma-names = "tx", "rx";
+};
+
+&sdhost {
+	dmas = <&dma 13>;
+	dma-names = "rx-tx";
+};
+
+&spi {
+	dmas = <&dma 6>, <&dma 7>;
+	dma-names = "tx", "rx";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts
index db8a6017f22..40b9405f1a8 100644
--- a/arch/arm/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-a-plus.dts
@@ -8,12 +8,17 @@
 	compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
 	model = "Raspberry Pi Model A+";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -99,6 +104,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -107,6 +114,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts
index 067d1f07a2d..11edb581dba 100644
--- a/arch/arm/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/dts/bcm2835-rpi-a.dts
@@ -8,8 +8,13 @@
 	compatible = "raspberrypi,model-a", "brcm,bcm2835";
 	model = "Raspberry Pi Model A";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -94,6 +99,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -102,6 +109,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts
index 1e40d672b05..1b435c64bd9 100644
--- a/arch/arm/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-plus.dts
@@ -9,12 +9,17 @@
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
 	model = "Raspberry Pi Model B+";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -101,6 +106,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -109,6 +116,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
index 28e7513ce61..a23c25c00ee 100644
--- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
@@ -9,8 +9,13 @@
 	compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
 	model = "Raspberry Pi Model B rev2";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -94,6 +99,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -102,6 +109,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
index 31ff602e2cd..1b63d6b1975 100644
--- a/arch/arm/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -9,8 +9,13 @@
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
 	model = "Raspberry Pi Model B";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -89,6 +94,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -97,6 +104,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts
index 4764a25585a..a75c882e657 100644
--- a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts
+++ b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts
@@ -79,6 +79,15 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
 };
 
 &uart0 {
diff --git a/arch/arm/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/dts/bcm2835-rpi-cm1.dtsi
index ef22c2da783..e4e6b6abbfc 100644
--- a/arch/arm/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/dts/bcm2835-rpi-cm1.dtsi
@@ -5,11 +5,16 @@
 
 / {
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
 	reg_3v3: fixed-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";
diff --git a/arch/arm/dts/bcm2835-rpi-common.dtsi b/arch/arm/dts/bcm2835-rpi-common.dtsi
new file mode 100644
index 00000000000..8a55b6cded5
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-common.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's
+ * firmware interface.
+ */
+
+#include <dt-bindings/power/raspberrypi-power.h>
+
+&v3d {
+	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+};
diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts
index ba0167df6c5..33b2b77aa47 100644
--- a/arch/arm/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts
@@ -12,14 +12,19 @@
 	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
 	model = "Raspberry Pi Zero W";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
 	chosen {
 		/* 8250 auxiliary UART instead of pl011 */
 		stdout-path = "serial1:115200n8";
 	};
 
 	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+		led-act {
+			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -100,12 +105,16 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhci {
 	#address-cells = <1>;
 	#size-cells = <0>;
+	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+	bus-width = <4>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	non-removable;
 	status = "okay";
@@ -116,6 +125,13 @@
 	};
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts
index 3b35a8a4a55..6f9b3a908f2 100644
--- a/arch/arm/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/dts/bcm2835-rpi-zero.dts
@@ -12,8 +12,13 @@
 	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
 	model = "Raspberry Pi Zero";
 
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
@@ -96,6 +101,15 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
 };
 
 &uart0 {
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
index 715d50c6452..87ddcad7608 100644
--- a/arch/arm/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -1,15 +1,10 @@
 #include <dt-bindings/power/raspberrypi-power.h>
 
 / {
-	memory@0 {
-		device_type = "memory";
-		reg = <0 0x10000000>;
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
-		act {
+		led-act {
 			label = "ACT";
 			default-state = "keep";
 			linux,default-trigger = "heartbeat";
@@ -18,8 +13,12 @@
 
 	soc {
 		firmware: firmware {
-			compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
+			compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
 			mboxes = <&mailbox>;
+			dma-ranges;
 		};
 
 		power: power {
@@ -64,32 +63,10 @@
 	clock-frequency = <100000>;
 };
 
-&i2c2 {
-	status = "okay";
-};
-
-&sdhci {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio48>;
-	bus-width = <4>;
-};
-
-&sdhost {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdhost_gpio48>;
-	status = "okay";
-	bus-width = <4>;
-};
-
 &usb {
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };
 
-&hdmi {
-	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
-	status = "okay";
-};
-
 &vec {
 	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
 	status = "okay";
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
index a5c3824c805..0549686134e 100644
--- a/arch/arm/dts/bcm2835.dtsi
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -1,5 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";
diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts
index 7b4e651bafd..d8af8eeac7b 100644
--- a/arch/arm/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/dts/bcm2836-rpi-2-b.dts
@@ -10,15 +10,16 @@
 	model = "Raspberry Pi 2 Model B";
 
 	memory@0 {
+		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -105,6 +106,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -113,6 +116,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi
index c933e841388..b390006aef7 100644
--- a/arch/arm/dts/bcm2836.dtsi
+++ b/arch/arm/dts/bcm2836.dtsi
@@ -1,5 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2836";
diff --git a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts
index 7f4437a8eed..77099a7871b 100644
--- a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts
@@ -14,17 +14,20 @@
 	};
 
 	memory@0 {
+		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
 		};
 	};
 };
@@ -117,6 +120,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
index c6fa34c2410..61010266ca9 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
@@ -15,17 +15,20 @@
 	};
 
 	memory@0 {
+		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
 		};
 	};
 
@@ -124,6 +127,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts
index ce71f578c51..dd4a4860409 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b.dts
@@ -15,11 +15,12 @@
 	};
 
 	memory@0 {
+		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
@@ -125,6 +126,8 @@
 
 &hdmi {
 	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 /* uart0 communicates with the BT module */
diff --git a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts
index 6c8233a36d8..588d9411ceb 100644
--- a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts
+++ b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts
@@ -78,6 +78,15 @@
 
 &hdmi {
 	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
 };
 
 &uart0 {
diff --git a/arch/arm/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/dts/bcm2837-rpi-cm3.dtsi
index 81399b2c5af..828a20561b9 100644
--- a/arch/arm/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/dts/bcm2837-rpi-cm3.dtsi
@@ -5,9 +5,18 @@
 
 / {
 	memory@0 {
+		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
 
+	leds {
+		/*
+		 * Since there is no upstream GPIO driver yet,
+		 * remove the incomplete node.
+		 */
+		/delete-node/ led-act;
+	};
+
 	reg_3v3: fixed-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";
diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi
index beb6c502dad..0199ec98cd6 100644
--- a/arch/arm/dts/bcm2837.dtsi
+++ b/arch/arm/dts/bcm2837.dtsi
@@ -1,4 +1,6 @@
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2837";
diff --git a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi
new file mode 100644
index 00000000000..0ff0e9e2532
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+	dr_mode = "peripheral";
+	g-rx-fifo-size = <256>;
+	g-np-tx-fifo-size = <32>;
+	g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};
diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi
index 9777644c6c2..a3e06b68094 100644
--- a/arch/arm/dts/bcm283x.dtsi
+++ b/arch/arm/dts/bcm283x.dtsi
@@ -18,7 +18,6 @@
 / {
 	compatible = "brcm,bcm2835";
 	model = "BCM2835";
-	interrupt-parent = <&intc>;
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -31,16 +30,27 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	rmem: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		cma: linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x4000000>; /* 64MB */
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&thermal>;
-
 			trips {
 				cpu-crit {
-					temperature	= <80000>;
+					temperature	= <90000>;
 					hysteresis	= <0>;
 					type		= "critical";
 				};
@@ -56,7 +66,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		timer@7e003000 {
+		system_timer: timer@7e003000 {
 			compatible = "brcm,bcm2835-system-timer";
 			reg = <0x7e003000 0x1000>;
 			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
@@ -67,74 +77,12 @@
 			clock-frequency = <1000000>;
 		};
 
-		txp@7e004000 {
+		txp: txp@7e004000 {
 			compatible = "brcm,bcm2835-txp";
 			reg = <0x7e004000 0x20>;
 			interrupts = <1 11>;
 		};
 
-		dma: dma@7e007000 {
-			compatible = "brcm,bcm2835-dma";
-			reg = <0x7e007000 0xf00>;
-			interrupts = <1 16>,
-				     <1 17>,
-				     <1 18>,
-				     <1 19>,
-				     <1 20>,
-				     <1 21>,
-				     <1 22>,
-				     <1 23>,
-				     <1 24>,
-				     <1 25>,
-				     <1 26>,
-				     /* dma channel 11-14 share one irq */
-				     <1 27>,
-				     <1 27>,
-				     <1 27>,
-				     <1 27>,
-				     /* unused shared irq for all channels */
-				     <1 28>;
-			interrupt-names = "dma0",
-					  "dma1",
-					  "dma2",
-					  "dma3",
-					  "dma4",
-					  "dma5",
-					  "dma6",
-					  "dma7",
-					  "dma8",
-					  "dma9",
-					  "dma10",
-					  "dma11",
-					  "dma12",
-					  "dma13",
-					  "dma14",
-					  "dma-shared-all";
-			#dma-cells = <1>;
-			brcm,dma-channel-mask = <0x7f35>;
-		};
-
-		intc: interrupt-controller@7e00b200 {
-			compatible = "brcm,bcm2835-armctrl-ic";
-			reg = <0x7e00b200 0x200>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		pm: watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
-			#power-domain-cells = <1>;
-			#reset-cells = <1>;
-			reg = <0x7e100000 0x114>,
-			      <0x7e00a000 0x24>;
-			clocks = <&clocks BCM2835_CLOCK_V3D>,
-				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
-				 <&clocks BCM2835_CLOCK_H264>,
-				 <&clocks BCM2835_CLOCK_ISP>;
-			clock-names = "v3d", "peri_image", "h264", "isp";
-			system-power-controller;
-		};
-
 		clocks: cprman@7e101000 {
 			compatible = "brcm,bcm2835-cprman";
 			#clock-cells = <1>;
@@ -149,12 +97,6 @@
 				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 		};
 
-		rng@7e104000 {
-			compatible = "brcm,bcm2835-rng";
-			reg = <0x7e104000 0x10>;
-			interrupts = <2 29>;
-		};
-
 		mailbox: mailbox@7e00b880 {
 			compatible = "brcm,bcm2835-mbox";
 			reg = <0x7e00b880 0x40>;
@@ -184,8 +126,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			/* Defines pin muxing groups according to
-			 * BCM2835-ARM-Peripherals.pdf page 102.
+			/* Defines common pin muxing groups
 			 *
 			 * While each pin can have its mux selected
 			 * for various functions individually, some
@@ -263,15 +204,7 @@
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			i2c_slave_gpio18: i2c_slave_gpio18 {
-				brcm,pins = <18 19 20 21>;
-				brcm,function = <BCM2835_FSEL_ALT3>;
-			};
 
-			jtag_gpio4: jtag_gpio4 {
-				brcm,pins = <4 5 6 12 13>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
 			jtag_gpio22: jtag_gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
@@ -286,35 +219,6 @@
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			pwm0_gpio12: pwm0_gpio12 {
-				brcm,pins = <12>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm0_gpio18: pwm0_gpio18 {
-				brcm,pins = <18>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
-			pwm0_gpio40: pwm0_gpio40 {
-				brcm,pins = <40>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio13: pwm1_gpio13 {
-				brcm,pins = <13>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio19: pwm1_gpio19 {
-				brcm,pins = <19>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
-			pwm1_gpio41: pwm1_gpio41 {
-				brcm,pins = <41>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio45: pwm1_gpio45 {
-				brcm,pins = <45>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-
 			sdhost_gpio48: sdhost_gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
@@ -396,8 +300,8 @@
 		};
 
 		uart0: serial@7e201000 {
-			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x200>;
 			interrupts = <2 25>;
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
@@ -410,8 +314,6 @@
 			reg = <0x7e202000 0x100>;
 			interrupts = <2 24>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			dmas = <&dma 13>;
-			dma-names = "rx-tx";
 			status = "disabled";
 		};
 
@@ -419,16 +321,12 @@
 			compatible = "brcm,bcm2835-i2s";
 			reg = <0x7e203000 0x24>;
 			clocks = <&clocks BCM2835_CLOCK_PCM>;
-
-			dmas = <&dma 2>,
-			       <&dma 3>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
 		spi: spi@7e204000 {
 			compatible = "brcm,bcm2835-spi";
-			reg = <0x7e204000 0x1000>;
+			reg = <0x7e204000 0x200>;
 			interrupts = <2 22>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			#address-cells = <1>;
@@ -438,7 +336,7 @@
 
 		i2c0: i2c@7e205000 {
 			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e205000 0x1000>;
+			reg = <0x7e205000 0x200>;
 			interrupts = <2 21>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			#address-cells = <1>;
@@ -446,18 +344,6 @@
 			status = "disabled";
 		};
 
-		pixelvalve@7e206000 {
-			compatible = "brcm,bcm2835-pixelvalve0";
-			reg = <0x7e206000 0x100>;
-			interrupts = <2 13>; /* pwa0 */
-		};
-
-		pixelvalve@7e207000 {
-			compatible = "brcm,bcm2835-pixelvalve1";
-			reg = <0x7e207000 0x100>;
-			interrupts = <2 14>; /* pwa1 */
-		};
-
 		dpi: dpi@7e208000 {
 			compatible = "brcm,bcm2835-dpi";
 			reg = <0x7e208000 0x8c>;
@@ -486,13 +372,6 @@
 					     "dsi0_ddr2",
 					     "dsi0_ddr";
 
-		};
-
-		thermal: thermal@7e212000 {
-			compatible = "brcm,bcm2835-thermal";
-			reg = <0x7e212000 0x8>;
-			clocks = <&clocks BCM2835_CLOCK_TSENS>;
-			#thermal-sensor-cells = <0>;
 			status = "disabled";
 		};
 
@@ -541,7 +420,7 @@
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
@@ -585,44 +464,6 @@
 			status = "disabled";
 		};
 
-		i2c2: i2c@7e805000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e805000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		vec: vec@7e806000 {
-			compatible = "brcm,bcm2835-vec";
-			reg = <0x7e806000 0x1000>;
-			clocks = <&clocks BCM2835_CLOCK_VEC>;
-			interrupts = <2 27>;
-			status = "disabled";
-		};
-
-		pixelvalve@7e807000 {
-			compatible = "brcm,bcm2835-pixelvalve2";
-			reg = <0x7e807000 0x100>;
-			interrupts = <2 10>; /* pixelvalve */
-		};
-
-		hdmi: hdmi@7e902000 {
-			compatible = "brcm,bcm2835-hdmi";
-			reg = <0x7e902000 0x600>,
-			      <0x7e808000 0x100>;
-			interrupts = <2 8>, <2 9>;
-			ddc = <&i2c2>;
-			clocks = <&clocks BCM2835_PLLH_PIX>,
-				 <&clocks BCM2835_CLOCK_HSM>;
-			clock-names = "pixel", "hdmi";
-			dmas = <&dma 17>;
-			dma-names = "audio-rx";
-			status = "disabled";
-		};
-
 		usb: usb@7e980000 {
 			compatible = "brcm,bcm2835-usb";
 			reg = <0x7e980000 0x10000>;
@@ -634,36 +475,19 @@
 			phys = <&usbphy>;
 			phy-names = "usb2-phy";
 		};
-
-		v3d: v3d@7ec00000 {
-			compatible = "brcm,bcm2835-v3d";
-			reg = <0x7ec00000 0x1000>;
-			interrupts = <1 10>;
-			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
-		};
-
-		vc4: gpu {
-			compatible = "brcm,bcm2835-vc4";
-		};
 	};
 
 	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		/* The oscillator is the root of the clock tree. */
-		clk_osc: clock@3 {
+		clk_osc: clk-osc {
 			compatible = "fixed-clock";
-			reg = <3>;
 			#clock-cells = <0>;
 			clock-output-names = "osc";
 			clock-frequency = <19200000>;
 		};
 
-		clk_usb: clock@4 {
+		clk_usb: clk-usb {
 			compatible = "fixed-clock";
-			reg = <4>;
 			#clock-cells = <0>;
 			clock-output-names = "otg";
 			clock-frequency = <480000000>;
diff --git a/configs/rpi_4_32b_defconfig b/configs/rpi_4_32b_defconfig
index 88f7504a60f..0d534b8a28d 100644
--- a/configs/rpi_4_32b_defconfig
+++ b/configs/rpi_4_32b_defconfig
@@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00008000
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_RPI_4_32B=y
 CONFIG_ENV_SIZE=0x4000
+CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b"
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_LOAD_ADDR=0x1000000
 CONFIG_OF_BOARD_SETUP=y
diff --git a/configs/rpi_4_defconfig b/configs/rpi_4_defconfig
index 59a71031540..0b3cadaced2 100644
--- a/configs/rpi_4_defconfig
+++ b/configs/rpi_4_defconfig
@@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00080000
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_RPI_4=y
 CONFIG_ENV_SIZE=0x4000
+CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b"
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_LOAD_ADDR=0x1000000
 CONFIG_OF_BOARD_SETUP=y
diff --git a/configs/rpi_arm64_defconfig b/configs/rpi_arm64_defconfig
index 67dbf094ef7..0b5f766cfe7 100644
--- a/configs/rpi_arm64_defconfig
+++ b/configs/rpi_arm64_defconfig
@@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00080000
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_RPI_ARM64=y
 CONFIG_ENV_SIZE=0x4000
+CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b"
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_LOAD_ADDR=0x1000000
 CONFIG_OF_BOARD_SETUP=y
diff --git a/include/dt-bindings/clock/bcm2835.h b/include/dt-bindings/clock/bcm2835.h
index 2cec01f9689..b60c03430cf 100644
--- a/include/dt-bindings/clock/bcm2835.h
+++ b/include/dt-bindings/clock/bcm2835.h
@@ -58,3 +58,5 @@
 #define BCM2835_CLOCK_DSI1E		48
 #define BCM2835_CLOCK_DSI0P		49
 #define BCM2835_CLOCK_DSI1P		50
+
+#define BCM2711_CLOCK_EMMC2		51