ARM: dts: sunxi: H2+/H3/H5: Sync from Linux v5.18-rc1

Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.

To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit also adds the following new board devicetree:
 - sun8i-h3-nanopi-r1.dts

This update should not impact any existing U-Boot functionality.

Signed-off-by: Samuel Holland <samuel@sholland.org>

17 files changed, 342 insertions, 24 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index d4b89b15e2..45dcf2e37f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -654,6 +654,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \
 	sun8i-h3-nanopi-neo-air.dtb \
+	sun8i-h3-nanopi-r1.dtb \
 	sun8i-h3-orangepi-2.dtb \
 	sun8i-h3-orangepi-lite.dtb \
 	sun8i-h3-orangepi-one.dtb \
diff --git a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
index b265720195..1afad8b437 100644
--- a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
+++ b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi
@@ -2,7 +2,7 @@
 // Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
index 55bcdf8d1a..55b369534a 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts
@@ -142,9 +142,16 @@
 	status = "okay";
 
 	eeprom@51 {
-		compatible = "microchip,24c02";
+		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x51>;
 		pagesize = <16>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth_mac1: mac-address@fa {
+			reg = <0xfa 0x06>;
+		};
 	};
 };
 
diff --git a/arch/arm/dts/sun50i-h5.dtsi b/arch/arm/dts/sun50i-h5.dtsi
index ab860e20d0..9b3462b13c 100644
--- a/arch/arm/dts/sun50i-h5.dtsi
+++ b/arch/arm/dts/sun50i-h5.dtsi
@@ -217,7 +217,7 @@
 			};
 		};
 
-		gpu_thermal {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
@@ -233,6 +233,10 @@
 	compatible = "allwinner,sun50i-h5-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun50i-h5-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun50i-h5-mmc",
 		     "allwinner,sun50i-a64-mmc";
diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index f3f7a2c912..d5c7b7984d 100644
--- a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -26,6 +26,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "c";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -41,8 +52,9 @@
 
 		sw4 {
 			label = "power";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
@@ -103,10 +115,24 @@
 	cpu-supply = <&reg_vdd_cpux>;
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
index 62b5280ec0..cd9f655e4f 100644
--- a/arch/arm/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -57,6 +57,12 @@
 		ethernet1 = &sdiowifi;
 	};
 
+	cec-gpio {
+		compatible = "cec-gpio";
+		cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
+		hdmi-phandle = <&hdmi>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -87,11 +93,15 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
-		clock-names = "ext_clock";
+	r-gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
 	};
 
 	sound_spdif {
@@ -111,6 +121,13 @@
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+	};
 };
 
 &de {
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
index be49eabbff..cd3df12b65 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
@@ -103,12 +103,40 @@
 	};
 };
 
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
 &usbphy {
 	/* USB VBUS is always on */
 	status = "okay";
diff --git a/arch/arm/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/dts/sun8i-h3-nanopi-r1.dts
new file mode 100644
index 0000000000..26e2e6172e
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-nanopi-r1.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Igor Pecovnik <igor@armbian.com>
+ * Copyright (C) 2020 Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
+ * Copyright (C) 2020 Yu-Tung Chang <mtwget@gmail.com>
+*/
+
+#include "sun8i-h3-nanopi.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "FriendlyARM NanoPi R1";
+	compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
+
+	aliases {
+		serial1 = &uart1;
+		ethernet0 = &emac;
+		ethernet1 = &wifi;
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+	};
+
+	reg_vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>;
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0>,
+			 <1300000 0x1>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+	};
+
+	leds {
+		led-2 {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		};
+
+		led-3 {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */
+		};
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	wifi: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi b/arch/arm/dts/sun8i-h3-nanopi.dtsi
index c7c3e7d8b3..fc45d5aaa6 100644
--- a/arch/arm/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi
@@ -81,6 +81,7 @@
 			label = "k1";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index 597c425d08..9daffd90c1 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -99,8 +99,9 @@
 
 		sw4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
index 5aff8ecc66..90f75fa85e 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
@@ -91,8 +91,9 @@
 
 		sw4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi
index 4e89701df9..eac2349a23 100644
--- a/arch/arm/dts/sun8i-h3.dtsi
+++ b/arch/arm/dts/sun8i-h3.dtsi
@@ -44,7 +44,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -112,7 +112,7 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-120000000 {
@@ -245,7 +245,7 @@
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
-			thermal-sensors = <&ths 0>;
+			thermal-sensors = <&ths>;
 
 			trips {
 				cpu_hot_trip: cpu-hot {
@@ -282,6 +282,10 @@
 	compatible = "allwinner,sun8i-h3-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun8i-h3-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun7i-a20-mmc";
 	clocks = <&ccu CLK_BUS_MMC0>,
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
index 22466afd38..235994a4a2 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
@@ -16,15 +16,27 @@
 		regulator-type = "voltage";
 		regulator-boot-on;
 		regulator-always-on;
-		regulator-min-microvolt = <1100000>;
-		regulator-max-microvolt = <1300000>;
+		regulator-min-microvolt = <1108475>;
+		regulator-max-microvolt = <1308475>;
 		regulator-ramp-delay = <50>; /* 4ms */
 		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
 		gpios-states = <0x1>;
-		states = <1100000 0>, <1300000 1>;
+		states = <1108475 0>, <1308475 1>;
 	};
 };
 
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
+
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
index 8e5cb3b3fd..d03f5853ef 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
@@ -82,8 +82,9 @@
 
 		sw4 {
 			label = "power";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
@@ -219,6 +220,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
+		max-speed = <1500000>;
 		clocks = <&rtc 1>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi
index 9be13378d4..6cea57e07f 100644
--- a/arch/arm/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/dts/sunxi-h3-h5.dtsi
@@ -567,9 +567,14 @@
 		};
 
 		mbus: dram-controller@1c62000 {
-			compatible = "allwinner,sun8i-h3-mbus";
-			reg = <0x01c62000 0x1000>;
-			clocks = <&ccu CLK_MBUS>;
+			/* compatible is in per SoC .dtsi file */
+			reg = <0x01c62000 0x1000>,
+			      <0x01c63000 0x1000>;
+			reg-names = "mbus", "dram";
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
@@ -812,8 +817,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc 0>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -859,6 +864,15 @@
 			#clock-cells = <1>;
 		};
 
+		r_intc: interrupt-controller@1f00c00 {
+			compatible = "allwinner,sun8i-h3-r-intc",
+				     "allwinner,sun6i-a31-r-intc";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x01f00c00 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun8i-h3-r-ccu";
 			reg = <0x01f01400 0x100>;
@@ -897,6 +911,19 @@
 			#size-cells = <0>;
 		};
 
+		r_uart: serial@1f02800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01f02800 0x400>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&r_ccu CLK_APB0_UART>;
+			resets = <&r_ccu RST_APB0_UART>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_uart_pins>;
+			status = "disabled";
+		};
+
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-h3-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
@@ -922,6 +949,11 @@
 				pins = "PL10";
 				function = "s_pwm";
 			};
+
+			r_uart_pins: r-uart-pins {
+				pins = "PL2", "PL3";
+				function = "s_uart";
+			};
 		};
 
 		r_pwm: pwm@1f03800 {
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
index 19b3b23cfa..9e14fe5fdc 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -49,6 +49,7 @@
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+			wakeup-source;
 		};
 	};
 
@@ -128,6 +129,18 @@
 	cpu-supply = <&reg_vdd_cpux>;
 };
 
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
index 204fba3614..50d328c2a8 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
@@ -156,7 +156,7 @@
 &spi0 {
 	status = "okay";
 
-	spiflash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <50000000>;