MLK-23574-50 mx7d_val: Add iMX7D validation board support

Porting the iMX7D 12x12 DDR3/LPDDR3 validation board and 19x19
DDR3/LPDDR2/LPDDR3 validation board support from v2019.04 u-boot.

Signed-off-by: Ye Li <ye.li@nxp.com>

51 files changed, 9535 insertions, 1 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 539488fb69..d8ca28a30e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -718,7 +718,14 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
 	imx7s-warp.dtb \
 	imx7d-meerkat96.dtb \
 	imx7d-pico-pi.dtb \
-	imx7d-pico-hobbit.dtb
+	imx7d-pico-hobbit.dtb \
+	imx7d-12x12-lpddr3-val.dtb \
+	imx7d-12x12-lpddr3-val-ecspi.dtb \
+	imx7d-12x12-lpddr3-val-qspi.dtb \
+	imx7d-12x12-ddr3-val.dtb \
+	imx7d-19x19-ddr3-val.dtb \
+	imx7d-19x19-lpddr2-val.dtb \
+	imx7d-19x19-lpddr3-val.dtb
 
 
 dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \
diff --git a/arch/arm/dts/imx7d-12x12-ddr3-val.dts b/arch/arm/dts/imx7d-12x12-ddr3-val.dts
new file mode 100644
index 0000000000..7081183acf
--- /dev/null
+++ b/arch/arm/dts/imx7d-12x12-ddr3-val.dts
@@ -0,0 +1,578 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "i.MX7 DDR3 12x12 VAL Board";
+	compatible = "fsl,imx7d-12x12-ddr3-val", "fsl,imx7d";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio3 17 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	pxp_v4l2_out {
+		compatible = "fsl,imx7d-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2";
+		status = "okay";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_sd3_vmmc: sd3_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD3";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio6 11 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg1_vbus: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg2_vbus: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_vref_1v8: regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		reg_can1_3v3: can1-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "can1-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		};
+
+		reg_can2_3v3: can2-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "can2-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory {
+		reg = <0x80000000 0x80000000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&ecspi4 {
+	fsl,spi-num-chipselects = <4>;
+	cs-gpios = <&gpio5 3 0>, <&gpio5 4 0>, <&gpio5 5 0>, <&gpio5 6 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4_1 &pinctrl_ecspi4_cs_1>;
+	status = "disabled";
+
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&epxp {
+	status = "okay";
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_3v3>;
+	status = "disabled";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_3v3>;
+	status = "disabled";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+	pinctrl-1 = <&pinctrl_i2c1_1_gpio>;
+	scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pfuze3000@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3_1>;
+	pinctrl-1 = <&pinctrl_i2c3_1_gpio>;
+	scl-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_1>;
+
+	imx7d-12x12-ddr3-val {
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 	0x59
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 	0x59
+				MX7D_PAD_SD2_RESET_B__GPIO5_IO11 	0x59
+			>;
+		};
+
+		pinctrl_ecspi4_cs_1: ecspi4_cs_grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD1_CLK__GPIO5_IO3 	0x2
+				MX7D_PAD_SD1_CMD__GPIO5_IO4 	0x2
+				MX7D_PAD_SD1_DATA0__GPIO5_IO5 	0x2
+				MX7D_PAD_SD1_DATA1__GPIO5_IO6 	0x2
+			>;
+		};
+
+		pinctrl_ecspi4_1: ecspi4grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD1_RESET_B__ECSPI4_SCLK 	0x2
+				MX7D_PAD_SD1_WP__ECSPI4_MOSI 		0x2
+				MX7D_PAD_SD1_CD_B__ECSPI4_MISO 	 	0x2
+			>;
+		};
+
+		pinctrl_flexcan1: flexcan1grp {
+			fsl,pins = <
+				MX7D_PAD_SD3_DATA5__FLEXCAN1_TX 	0x59
+				MX7D_PAD_SD3_DATA7__FLEXCAN1_RX 	0x59
+			>;
+		};
+
+		pinctrl_flexcan2: flexcan2grp {
+			fsl,pins = <
+				MX7D_PAD_SD3_DATA6__FLEXCAN2_TX 	0x59
+				MX7D_PAD_SD3_DATA4__FLEXCAN2_RX 	0x59
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				MX7D_PAD_LCD_DATA12__GPIO3_IO17 0x32
+				MX7D_PAD_LCD_DATA13__GPIO3_IO18 0x32
+			>;
+		};
+
+		pinctrl_i2c3_1: i2c3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ENET1_RGMII_RD0__I2C3_SCL 0x4000007f
+				MX7D_PAD_ENET1_RGMII_RD1__I2C3_SDA 0x4000007f
+			>;
+		};
+
+		pinctrl_i2c3_1_gpio: i2c3grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0 0x7f
+				MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1 0x7f
+			>;
+		};
+
+		pinctrl_i2c4_1: i2c4grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL 0x4000007f
+				MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA 0x4000007f
+			>;
+		};
+
+		pinctrl_lcdif_dat: lcdifdatgrp {
+			fsl,pins = <
+				MX7D_PAD_EPDC_DATA00__LCD_DATA0  0x4001b0b0
+				MX7D_PAD_EPDC_DATA01__LCD_DATA1  0x4001b0b0
+				MX7D_PAD_EPDC_DATA02__LCD_DATA2  0x4001b0b0
+				MX7D_PAD_EPDC_DATA03__LCD_DATA3  0x4001b0b0
+				MX7D_PAD_EPDC_DATA04__LCD_DATA4  0x4001b0b0
+				MX7D_PAD_EPDC_DATA05__LCD_DATA5  0x4001b0b0
+				MX7D_PAD_EPDC_DATA06__LCD_DATA6  0x4001b0b0
+				MX7D_PAD_EPDC_DATA07__LCD_DATA7  0x4001b0b0
+				MX7D_PAD_EPDC_DATA08__LCD_DATA8  0x4001b0b0
+				MX7D_PAD_EPDC_DATA09__LCD_DATA9  0x4001b0b0
+				MX7D_PAD_EPDC_DATA10__LCD_DATA10 0x4001b0b0
+				MX7D_PAD_EPDC_DATA11__LCD_DATA11 0x4001b0b0
+				MX7D_PAD_EPDC_DATA12__LCD_DATA12 0x4001b0b0
+				MX7D_PAD_EPDC_DATA13__LCD_DATA13 0x4001b0b0
+				MX7D_PAD_EPDC_DATA14__LCD_DATA14 0x4001b0b0
+				MX7D_PAD_EPDC_DATA15__LCD_DATA15 0x4001b0b0
+				MX7D_PAD_EPDC_SDLE__LCD_DATA16   0x4001b0b0
+				MX7D_PAD_EPDC_SDOE__LCD_DATA17   0x4001b0b0
+				MX7D_PAD_EPDC_SDSHR__LCD_DATA18  0x4001b0b0
+				MX7D_PAD_EPDC_SDCE0__LCD_DATA19  0x4001b0b0
+				MX7D_PAD_EPDC_SDCE1__LCD_DATA20  0x4001b0b0
+				MX7D_PAD_EPDC_SDCE2__LCD_DATA21  0x4001b0b0
+				MX7D_PAD_EPDC_SDCE3__LCD_DATA22  0x4001b0b0
+				MX7D_PAD_EPDC_GDCLK__LCD_DATA23  0x4001b0b0
+			>;
+		};
+
+		pinctrl_lcdif_ctrl: lcdifctrlgrp {
+			fsl,pins = <
+				MX7D_PAD_EPDC_SDCLK__LCD_CLK 		0x4001b0b0
+				MX7D_PAD_EPDC_BDR1__LCD_ENABLE 		0x4001b0b0
+				MX7D_PAD_EPDC_PWR_STAT__LCD_VSYNC 	0x4001b0b0
+				MX7D_PAD_EPDC_PWR_COM__LCD_HSYNC 	0x4001b0b0
+			>;
+		};
+
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+			>;
+		};
+
+		pinctrl_uart1_1: uart1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+			>;
+		};
+
+		pinctrl_usdhc2_1: usdhc2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     	0x59
+				MX7D_PAD_SD2_CLK__SD2_CLK     	0x19
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 	0x59
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 	0x59
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 	0x59
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 	0x59
+				MX7D_PAD_ECSPI1_SCLK__SD2_DATA4 0x59
+				MX7D_PAD_ECSPI1_MOSI__SD2_DATA5 0x59
+				MX7D_PAD_ECSPI1_MISO__SD2_DATA6 0x59
+				MX7D_PAD_ECSPI1_SS0__SD2_DATA7 	0x59
+			>;
+		};
+
+		pinctrl_usdhc2_1_100mhz: usdhc2grp-1_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     	0x5a
+				MX7D_PAD_SD2_CLK__SD2_CLK     	0x1a
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 	0x5a
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 	0x5a
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 	0x5a
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 	0x5a
+				MX7D_PAD_ECSPI1_SCLK__SD2_DATA4 0x5a
+				MX7D_PAD_ECSPI1_MOSI__SD2_DATA5 0x5a
+				MX7D_PAD_ECSPI1_MISO__SD2_DATA6 0x5a
+				MX7D_PAD_ECSPI1_SS0__SD2_DATA7 	0x5a
+			>;
+		};
+
+		pinctrl_usdhc2_1_200mhz: usdhc2grp-1_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     	0x5b
+				MX7D_PAD_SD2_CLK__SD2_CLK     	0x1b
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 	0x5b
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 	0x5b
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 	0x5b
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 	0x5b
+				MX7D_PAD_ECSPI1_SCLK__SD2_DATA4 0x5b
+				MX7D_PAD_ECSPI1_MOSI__SD2_DATA5 0x5b
+				MX7D_PAD_ECSPI1_MISO__SD2_DATA6 0x5b
+				MX7D_PAD_ECSPI1_SS0__SD2_DATA7 	0x5b
+			>;
+		};
+
+		pinctrl_usdhc3_1: usdhc3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD	    0x59
+				MX7D_PAD_SD3_CLK__SD3_CLK	    0x19
+				MX7D_PAD_SD3_DATA0__SD3_DATA0   0x59
+				MX7D_PAD_SD3_DATA1__SD3_DATA1   0x59
+				MX7D_PAD_SD3_DATA2__SD3_DATA2   0x59
+				MX7D_PAD_SD3_DATA3__SD3_DATA3   0x59
+			>;
+		};
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-12x12-ddr3-val {
+		pinctrl_hog_2: hoggrp-2 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59 /* flexcan stby1 */
+				MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59 /* flexcan stby2 */
+				MX7D_PAD_LPSR_GPIO1_IO01__ANATOP_24M_OUT	0x80000000
+			>;
+		};
+
+		pinctrl_i2c1_1: i2c1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL	0x4000007f
+				MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
+			>;
+		};
+
+		pinctrl_i2c1_1_gpio: i2c1grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 	0x7f
+				MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5   0x7f
+			>;
+		};
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO06__I2C2_SCL	0x4000007f
+				MX7D_PAD_LPSR_GPIO1_IO07__I2C2_SDA	0x4000007f
+			>;
+		};
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display {
+		bits-per-pixel = <16>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <89>;
+				hfront-porch = <164>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				hsync-len = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&sdma {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	status = "okay";
+};
+
+&usbh {
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2_1>;
+	pinctrl-1 = <&pinctrl_usdhc2_1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_1_200mhz>;
+	assigned-clocks = <&clks IMX7D_USDHC2_ROOT_CLK>;
+	assigned-clocks-rates = <400000000>;
+	bus-width = <8>;
+	tuning-step = <2>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_1>;
+	vmmc-supply = <&reg_sd3_vmmc>;
+	cd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	no-1-8-v;
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx7d-12x12-lpddr3-val-ecspi.dts b/arch/arm/dts/imx7d-12x12-lpddr3-val-ecspi.dts
new file mode 100644
index 0000000000..29abc2c86b
--- /dev/null
+++ b/arch/arm/dts/imx7d-12x12-lpddr3-val-ecspi.dts
@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "imx7d-12x12-lpddr3-val.dts"
+
+&epdc {
+        status = "disabled";
+};
+
+&ecspi1{
+        status = "okay";
+};
+
+/*
+ * pin conflict with ecspi1
+ * default hog setting conflicts with ECSPI1 MOSI and MISO
+ * EPDC PWRCTRL conflicts with ECSPI1 CS pin
+ */
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog_1>;
+	pinctrl-1 = <&pinctrl_hog_1>;
+};
diff --git a/arch/arm/dts/imx7d-12x12-lpddr3-val-qspi.dts b/arch/arm/dts/imx7d-12x12-lpddr3-val-qspi.dts
new file mode 100644
index 0000000000..5ceccd2ba0
--- /dev/null
+++ b/arch/arm/dts/imx7d-12x12-lpddr3-val-qspi.dts
@@ -0,0 +1,84 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "imx7d-12x12-lpddr3-val.dts"
+
+/* disable epdc, conflict with qspi */
+&epdc {
+        status = "disabled";
+};
+
+&iomuxc {
+	qspi1 {
+		pinctrl_qspi1_1: qspi1grp_1 {
+			fsl,pins = <
+				MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 0x51
+				MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 0x51
+				MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 0x51
+				MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 0x51
+				MX7D_PAD_EPDC_DATA04__QSPI_A_DQS 0x51
+				MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK 0x51
+				MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B 0x51
+				MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B 0x51
+				MX7D_PAD_EPDC_DATA08__QSPI_B_DATA0 0x51
+				MX7D_PAD_EPDC_DATA09__QSPI_B_DATA1 0x51
+				MX7D_PAD_EPDC_DATA10__QSPI_B_DATA2 0x51
+				MX7D_PAD_EPDC_DATA11__QSPI_B_DATA3 0x51
+				MX7D_PAD_EPDC_DATA12__QSPI_B_DQS 0x51
+				MX7D_PAD_EPDC_DATA13__QSPI_B_SCLK 0x51
+				MX7D_PAD_EPDC_DATA14__QSPI_B_SS0_B 0x51
+				MX7D_PAD_EPDC_DATA15__QSPI_B_SS1_B 0x51
+			>;
+		};
+	};
+};
+
+&qspi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_qspi1_1>;
+	pinctrl-1 = <&pinctrl_qspi1_1>;
+	status = "okay";
+	fsl,qspi-has-second-chip = <1>;
+	ddrsmp=<0>;
+
+	flash0: n25q256a@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <0>;
+	};
+
+	flash1: n25q256a@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <1>;
+	};
+
+	flash2: n25q256a@2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <2>;
+	};
+
+	flash3: n25q256a@3 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <3>;
+	};
+};
diff --git a/arch/arm/dts/imx7d-12x12-lpddr3-val.dts b/arch/arm/dts/imx7d-12x12-lpddr3-val.dts
new file mode 100644
index 0000000000..5f01fe8ae7
--- /dev/null
+++ b/arch/arm/dts/imx7d-12x12-lpddr3-val.dts
@@ -0,0 +1,1035 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx7d.dtsi"
+
+/ {
+	model = "i.MX7 LPDDR3 12x12 VAL Board";
+	compatible = "fsl,imx7d-12x12-lpddr3-val", "fsl,imx7d";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		pinctrl-1 = <&pinctrl_gpio_keys_sleep>;
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	pxp_v4l2_out {
+		compatible = "fsl,imx7d-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2";
+		status = "okay";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_aud_1v8: aud_1v8 {
+			compatible = "regulator-fixed";
+			regulator-name = "AUD_1V8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_can1_3v3: can1-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "can1-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+
+		reg_can2_3v3: can2-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "can2-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		reg_coedc_5v: coedc_5v {
+			compatible = "regulator-fixed";
+			regulator-name = "CODEC_5V";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_sd1_vmmc: sd1_vmmc{
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD1";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_sd2_vmmc: sd2_vmmc{
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD2";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg1_vbus: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg2_vbus: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_vref_1v8: regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		reg_mipi_dsi_pwr_on: mipi_dsi_pwr_on {
+			compatible = "regulator-fixed";
+			regulator-name = "mipi_dsi_pwr_on";
+			gpio = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+                };
+	};
+
+	memory {
+		reg = <0x80000000 0x80000000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&epdc {
+        pinctrl-names = "default", "sleep";
+        pinctrl-0 = <&pinctrl_epdc_0>;
+        pinctrl-1 = <&pinctrl_epdc_0>;
+        V3P3-supply = <&V3P3_reg>;
+        VCOM-supply = <&VCOM_reg>;
+        DISPLAY-supply = <&DISPLAY_reg>;
+        status = "okay";
+};
+
+&epxp {
+	status = "okay";
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio4 19 0>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_cs_1>;
+	pinctrl-1 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_cs_1>;
+	status = "disabled";
+
+	spi_flash1: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet1>;
+	pinctrl-1 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@5 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <5>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet2>;
+	pinctrl-1 = <&pinctrl_enet2>;
+	pinctrl-assert-gpios = <&max7322 0 GPIO_ACTIVE_HIGH>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "disabled";
+};
+
+&flexcan1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-1 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_3v3>;
+	status = "disabled";
+};
+
+&flexcan2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-1 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_3v3>;
+	status = "disabled";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "sleep", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+	pinctrl-1 = <&pinctrl_i2c1_1>;
+	pinctrl-2 = <&pinctrl_i2c1_1_gpio>;
+	scl-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pfuze3000@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+		fsl,lpsr-mode;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "sleep", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3_1>;
+	pinctrl-1 = <&pinctrl_i2c3_1>;
+	pinctrl-2 = <&pinctrl_i2c3_1_gpio>;
+	scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	max7322: gpio@68 {
+		compatible = "maxim,max7322";
+		reg = <0x68>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	max17135@48 {
+		compatible = "maxim,max17135";
+		reg = <0x48>;
+		vneg_pwrup = <1>;
+		gvee_pwrup = <2>;
+		vpos_pwrup = <10>;
+		gvdd_pwrup = <12>;
+		gvdd_pwrdn = <1>;
+		vpos_pwrdn = <2>;
+		gvee_pwrdn = <8>;
+		vneg_pwrdn = <10>;
+		gpio_pmic_pwrgood = <&gpio2 31 0>;
+		gpio_pmic_vcom_ctrl = <&gpio4 14 0>;
+		gpio_pmic_wakeup = <&gpio4 23 0>;
+		gpio_pmic_v3p3 = <&gpio4 20 0>;
+		gpio_pmic_intr = <&gpio4 18 0>;
+
+		regulators {
+			DISPLAY_reg: DISPLAY {
+				regulator-name = "DISPLAY";
+			};
+
+			GVDD_reg: GVDD {
+				/* 20v */
+				regulator-name = "GVDD";
+			};
+
+			GVEE_reg: GVEE {
+				/* -22v */
+				regulator-name = "GVEE";
+			};
+
+			HVINN_reg: HVINN {
+				/* -22v */
+				regulator-name = "HVINN";
+			};
+
+			HVINP_reg: HVINP {
+				/* 20v */
+				regulator-name = "HVINP";
+			};
+
+			VCOM_reg: VCOM {
+				regulator-name = "VCOM";
+				/* Real max value: -500000 */
+				regulator-max-microvolt = <4325000>;
+				/* Real min value: -4325000 */
+				regulator-min-microvolt = <500000>;
+			};
+
+			VNEG_reg: VNEG {
+				/* -15v */
+				regulator-name = "VNEG";
+			};
+
+			VPOS_reg: VPOS {
+				/* 15v */
+				regulator-name = "VPOS";
+			};
+
+			V3P3_reg: V3P3 {
+				regulator-name = "V3P3";
+			};
+		};
+	};
+
+	codec: wm8958@1a {
+		compatible = "wlf,wm8958";
+		reg = <0x1a>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>,
+		         <&clks IMX7D_CLK_DUMMY>;
+		clock-names = "mclk1", "mclk2";
+
+		DBVDD1-supply = <&reg_aud_1v8>;
+		DBVDD2-supply = <&reg_aud_1v8>;
+		DBVDD3-supply = <&reg_aud_1v8>;
+		AVDD2-supply = <&reg_aud_1v8>;
+		CPVDD-supply = <&reg_aud_1v8>;
+		SPKVDD1-supply = <&reg_coedc_5v>;
+		SPKVDD2-supply = <&reg_coedc_5v>;
+		wlf,ldo1ena;
+		wlf,ldo2ena;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_hog_1 &pinctrl_hog_sd2_vselect &pinctrl_hog_mipi>;
+	pinctrl-1 = <&pinctrl_hog_1 &pinctrl_hog_sd2_vselect &pinctrl_hog_mipi>;
+
+	imx7d-12x12-lpddr3-val {
+
+		pinctrl_bt: btgrp-1 {
+			fsl,pins = <
+				MX7D_PAD_ENET1_CRS__GPIO7_IO14    0x80000000  /* BT REG on */
+			>;
+		};
+
+		pinctrl_ecspi1_cs_1: ecspi1_cs_grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ECSPI1_SS0__GPIO4_IO19     0x2
+			>;
+		};
+
+		pinctrl_ecspi1_1: ecspi1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO   0x2
+				MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI   0x2
+				MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK   0x2
+			>;
+		};
+
+		pinctrl_enet1: enet1grp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x3
+				MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x3
+				MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
+				MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
+				MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
+				MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
+				MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
+				MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
+				MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
+				MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
+				MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
+				MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
+				MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
+				MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
+			>;
+		};
+
+		pinctrl_enet2: enet2grp {
+			fsl,pins = <
+				MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC     0x1
+				MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0    0x1
+				MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1    0x1
+				MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2    0x1
+				MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3     0x1
+				MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL  0x1
+				MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC    0x1
+				MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0    0x1
+				MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1     0x1
+				MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2     0x1
+				MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3    0x1
+				MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x1
+			>;
+		};
+
+		pinctrl_epdc_0: epdcgrp-0 {
+			fsl,pins = <
+				MX7D_PAD_EPDC_DATA00__EPDC_DATA0  0x2
+				MX7D_PAD_EPDC_DATA01__EPDC_DATA1  0x2
+				MX7D_PAD_EPDC_DATA02__EPDC_DATA2  0x2
+				MX7D_PAD_EPDC_DATA03__EPDC_DATA3  0x2
+				MX7D_PAD_EPDC_DATA04__EPDC_DATA4  0x2
+				MX7D_PAD_EPDC_DATA05__EPDC_DATA5  0x2
+				MX7D_PAD_EPDC_DATA06__EPDC_DATA6  0x2
+				MX7D_PAD_EPDC_DATA07__EPDC_DATA7  0x2
+				MX7D_PAD_EPDC_DATA08__EPDC_DATA8  0x2
+				MX7D_PAD_EPDC_DATA09__EPDC_DATA9  0x2
+				MX7D_PAD_EPDC_DATA10__EPDC_DATA10 0x2
+				MX7D_PAD_EPDC_DATA11__EPDC_DATA11 0x2
+				MX7D_PAD_EPDC_DATA12__EPDC_DATA12 0x2
+				MX7D_PAD_EPDC_DATA13__EPDC_DATA13 0x2
+				MX7D_PAD_EPDC_DATA14__EPDC_DATA14 0x2
+				MX7D_PAD_EPDC_DATA15__EPDC_DATA15 0x2
+				MX7D_PAD_EPDC_SDCLK__EPDC_SDCLK   0x2
+				MX7D_PAD_EPDC_SDLE__EPDC_SDLE     0x2
+				MX7D_PAD_EPDC_SDOE__EPDC_SDOE     0x2
+				MX7D_PAD_EPDC_SDSHR__EPDC_SDSHR   0x2
+				MX7D_PAD_EPDC_SDCE0__EPDC_SDCE0   0x2
+				MX7D_PAD_EPDC_SDCE1__EPDC_SDCE1   0x2
+				MX7D_PAD_EPDC_SDCE2__EPDC_SDCE2   0x2
+				MX7D_PAD_EPDC_SDCE3__EPDC_SDCE3   0x2
+				MX7D_PAD_EPDC_GDCLK__EPDC_GDCLK   0x2
+				MX7D_PAD_EPDC_GDOE__EPDC_GDOE     0x2
+				MX7D_PAD_EPDC_GDRL__EPDC_GDRL     0x2
+				MX7D_PAD_EPDC_GDSP__EPDC_GDSP     0x2
+				MX7D_PAD_EPDC_BDR0__EPDC_BDR0     0x2
+				MX7D_PAD_EPDC_BDR1__EPDC_BDR1     0x2
+				MX7D_PAD_ECSPI1_MISO__GPIO4_IO18  0x80000000  /* pwr int */
+			>;
+		};
+
+		pinctrl_flexcan1: flexcan1grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_RX_DATA__FLEXCAN1_RX	0x59
+				MX7D_PAD_SAI1_TX_BCLK__FLEXCAN1_TX	0x59
+				MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x59 /* STBY */
+			>;
+		};
+
+		pinctrl_flexcan2: flexcan2grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_TX_SYNC__FLEXCAN2_RX	0x59
+				MX7D_PAD_SAI1_TX_DATA__FLEXCAN2_TX	0x59
+				MX7D_PAD_GPIO1_IO11__GPIO1_IO11		0x59  /* STBY */
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x32
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x32
+			>;
+		};
+
+		pinctrl_gpio_keys_sleep: gpio_keysgrp_sleep {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x14
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x14
+			>;
+		};
+
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C4_SCL__GPIO4_IO14	0x80000000
+				MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x80000000
+				MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20  0x80000000
+				MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21  0x80000000
+				MX7D_PAD_ECSPI2_MISO__GPIO4_IO22  0x80000000
+				MX7D_PAD_ECSPI2_SS0__GPIO4_IO23	  0x80000000
+				MX7D_PAD_SD1_RESET_B__GPIO5_IO2   0x59
+				MX7D_PAD_SD1_CD_B__GPIO5_IO0      0x59
+				MX7D_PAD_SD1_WP__GPIO5_IO1        0x59
+				MX7D_PAD_SD2_CD_B__GPIO5_IO9      0x59
+				MX7D_PAD_SD2_WP__GPIO5_IO10       0x59
+				MX7D_PAD_SD2_RESET_B__GPIO5_IO11  0x59
+				MX7D_PAD_GPIO1_IO13__GPIO1_IO13   0x59
+			>;
+		};
+
+		pinctrl_hog_mipi: hoggrp_mipi {
+			fsl,pins = <
+                                MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16  0x59
+                                MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17  0x59
+			>;
+		};
+
+		pinctrl_hog_sd2_vselect: hoggrp_sd2vselect {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO12__SD2_VSELECT  0x59
+			>;
+		};
+
+		pinctrl_hog_headphone_det: hoggrp_headphone_det {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO12__GPIO1_IO12	  0x59
+			>;
+		};
+
+		pinctrl_i2c1_1: i2c1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__I2C1_SDA          0x4000007f
+				MX7D_PAD_I2C1_SCL__I2C1_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c1_1_gpio: i2c1grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__GPIO4_IO9          0x7f
+				MX7D_PAD_I2C1_SCL__GPIO4_IO8          0x7f
+			>;
+		};
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__I2C2_SDA          0x4000007f
+				MX7D_PAD_I2C2_SCL__I2C2_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c3_1: i2c3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C3_SDA__I2C3_SDA	     0x4000007f
+				MX7D_PAD_I2C3_SCL__I2C3_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c3_1_gpio: i2c3grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C3_SDA__GPIO4_IO13          0x7f
+				MX7D_PAD_I2C3_SCL__GPIO4_IO12          0x7f
+			>;
+		};
+
+		pinctrl_i2c4_1: i2c4grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C4_SDA__I2C4_SDA          0x4000007f
+				MX7D_PAD_I2C4_SCL__I2C4_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_lcdif_dat: lcdifdatgrp {
+			fsl,pins = <
+				MX7D_PAD_LCD_DATA00__LCD_DATA0  0x79
+				MX7D_PAD_LCD_DATA01__LCD_DATA1  0x79
+				MX7D_PAD_LCD_DATA02__LCD_DATA2  0x79
+				MX7D_PAD_LCD_DATA03__LCD_DATA3  0x79
+				MX7D_PAD_LCD_DATA04__LCD_DATA4  0x79
+				MX7D_PAD_LCD_DATA05__LCD_DATA5  0x79
+				MX7D_PAD_LCD_DATA06__LCD_DATA6  0x79
+				MX7D_PAD_LCD_DATA07__LCD_DATA7  0x79
+				MX7D_PAD_LCD_DATA08__LCD_DATA8  0x79
+				MX7D_PAD_LCD_DATA09__LCD_DATA9  0x79
+				MX7D_PAD_LCD_DATA10__LCD_DATA10 0x79
+				MX7D_PAD_LCD_DATA11__LCD_DATA11 0x79
+				MX7D_PAD_LCD_DATA12__LCD_DATA12 0x79
+				MX7D_PAD_LCD_DATA13__LCD_DATA13 0x79
+				MX7D_PAD_LCD_DATA14__LCD_DATA14 0x79
+				MX7D_PAD_LCD_DATA15__LCD_DATA15 0x79
+				MX7D_PAD_LCD_DATA16__LCD_DATA16 0x79
+				MX7D_PAD_LCD_DATA17__LCD_DATA17 0x79
+				MX7D_PAD_LCD_DATA18__LCD_DATA18 0x79
+				MX7D_PAD_LCD_DATA19__LCD_DATA19 0x79
+				MX7D_PAD_LCD_DATA20__LCD_DATA20 0x79
+				MX7D_PAD_LCD_DATA21__LCD_DATA21 0x79
+				MX7D_PAD_LCD_DATA22__LCD_DATA22 0x79
+				MX7D_PAD_LCD_DATA23__LCD_DATA23 0x79
+			>;
+		};
+
+		pinctrl_lcdif_ctrl: lcdifctrlgrp {
+			fsl,pins = <
+				MX7D_PAD_LCD_CLK__LCD_CLK       0x79
+				MX7D_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+				MX7D_PAD_LCD_VSYNC__LCD_VSYNC   0x79
+				MX7D_PAD_LCD_HSYNC__LCD_HSYNC   0x79
+			>;
+		};
+
+		pinctrl_mqs: mqsgrp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_RX_SYNC__MQS_RIGHT     0x0
+				MX7D_PAD_SAI1_RX_BCLK__MQS_LEFT      0x0
+			>;
+		};
+
+		pinctrl_pcie: pciegrp {
+			fsl,pins = <
+				MX7D_PAD_SAI2_TX_SYNC__GPIO6_IO19	0x2
+				MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x2
+			>;
+		};
+
+		pinctrl_sai1: sai1grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+				MX7D_PAD_SAI1_TX_BCLK__SAI1_TX_BCLK     0x1f
+				MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC     0x1f
+				MX7D_PAD_SAI1_RX_SYNC__SAI1_RX_SYNC     0x1f
+				MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0    0x1f
+				MX7D_PAD_SAI1_TX_DATA__SAI1_TX_DATA0    0
+			>;
+		};
+
+		pinctrl_sai2: sai2grp {
+			fsl,pins = <
+				MX7D_PAD_SAI2_TX_BCLK__SAI2_TX_BCLK     0x1f
+				MX7D_PAD_SAI2_TX_SYNC__SAI2_TX_SYNC     0x1f
+				MX7D_PAD_SAI2_RX_DATA__SAI2_RX_DATA0    0x1f
+				MX7D_PAD_SAI2_TX_DATA__SAI2_TX_DATA0    0
+			>;
+		};
+
+		pinctrl_uart1_1: uart1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+			>;
+		};
+
+		pinctrl_uart3_1: uart3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX    0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX    0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS     0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS     0x79
+			>;
+		};
+
+		pinctrl_uart3dte_1: uart3dtegrp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX    0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX    0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS     0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DTE_RTS     0x79
+			>;
+		};
+
+		pinctrl_usdhc1_1: usdhc1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD	0x59
+				MX7D_PAD_SD1_CLK__SD1_CLK	0x19
+				MX7D_PAD_SD1_DATA0__SD1_DATA0	0x59
+				MX7D_PAD_SD1_DATA1__SD1_DATA1	0x59
+				MX7D_PAD_SD1_DATA2__SD1_DATA2	0x59
+				MX7D_PAD_SD1_DATA3__SD1_DATA3	0x59
+			>;
+		};
+
+		pinctrl_usdhc2_1: usdhc2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD	0x59
+				MX7D_PAD_SD2_CLK__SD2_CLK	0x19
+				MX7D_PAD_SD2_DATA0__SD2_DATA0	0x59
+				MX7D_PAD_SD2_DATA1__SD2_DATA1	0x59
+				MX7D_PAD_SD2_DATA2__SD2_DATA2	0x59
+				MX7D_PAD_SD2_DATA3__SD2_DATA3	0x59
+			>;
+		};
+
+		pinctrl_usdhc2_1_100mhz: usdhc2grp-1_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD	0x5a
+				MX7D_PAD_SD2_CLK__SD2_CLK	0x1a
+				MX7D_PAD_SD2_DATA0__SD2_DATA0	0x5a
+				MX7D_PAD_SD2_DATA1__SD2_DATA1	0x5a
+				MX7D_PAD_SD2_DATA2__SD2_DATA2	0x5a
+				MX7D_PAD_SD2_DATA3__SD2_DATA3	0x5a
+			>;
+		};
+
+		pinctrl_usdhc2_1_200mhz: usdhc2grp-1_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD	0x5b
+				MX7D_PAD_SD2_CLK__SD2_CLK	0x1b
+				MX7D_PAD_SD2_DATA0__SD2_DATA0	0x5b
+				MX7D_PAD_SD2_DATA1__SD2_DATA1	0x5b
+				MX7D_PAD_SD2_DATA2__SD2_DATA2	0x5b
+				MX7D_PAD_SD2_DATA3__SD2_DATA3	0x5b
+			>;
+		};
+
+		pinctrl_usdhc3_1: usdhc3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD	0x59
+				MX7D_PAD_SD3_CLK__SD3_CLK	0x19
+				MX7D_PAD_SD3_DATA0__SD3_DATA0	0x59
+				MX7D_PAD_SD3_DATA1__SD3_DATA1	0x59
+				MX7D_PAD_SD3_DATA2__SD3_DATA2	0x59
+				MX7D_PAD_SD3_DATA3__SD3_DATA3	0x59
+				MX7D_PAD_SD3_DATA4__SD3_DATA4	0x59
+				MX7D_PAD_SD3_DATA5__SD3_DATA5	0x59
+				MX7D_PAD_SD3_DATA6__SD3_DATA6	0x59
+				MX7D_PAD_SD3_DATA7__SD3_DATA7	0x59
+				MX7D_PAD_SD3_STROBE__SD3_STROBE	0x19
+			>;
+		};
+
+		pinctrl_usdhc3_1_100mhz: usdhc3grp-1_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD	0x5a
+				MX7D_PAD_SD3_CLK__SD3_CLK	0x1a
+				MX7D_PAD_SD3_DATA0__SD3_DATA0	0x5a
+				MX7D_PAD_SD3_DATA1__SD3_DATA1	0x5a
+				MX7D_PAD_SD3_DATA2__SD3_DATA2	0x5a
+				MX7D_PAD_SD3_DATA3__SD3_DATA3	0x5a
+				MX7D_PAD_SD3_DATA4__SD3_DATA4	0x5a
+				MX7D_PAD_SD3_DATA5__SD3_DATA5	0x5a
+				MX7D_PAD_SD3_DATA6__SD3_DATA6	0x5a
+				MX7D_PAD_SD3_DATA7__SD3_DATA7	0x5a
+				MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1a
+			>;
+		};
+
+		pinctrl_usdhc3_1_200mhz: usdhc3grp-1_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD	0x5b
+				MX7D_PAD_SD3_CLK__SD3_CLK	0x1b
+				MX7D_PAD_SD3_DATA0__SD3_DATA0	0x5b
+				MX7D_PAD_SD3_DATA1__SD3_DATA1	0x5b
+				MX7D_PAD_SD3_DATA2__SD3_DATA2	0x5b
+				MX7D_PAD_SD3_DATA3__SD3_DATA3	0x5b
+				MX7D_PAD_SD3_DATA4__SD3_DATA4	0x5b
+				MX7D_PAD_SD3_DATA5__SD3_DATA5	0x5b
+				MX7D_PAD_SD3_DATA6__SD3_DATA6	0x5b
+				MX7D_PAD_SD3_DATA7__SD3_DATA7	0x5b
+				MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1b
+			>;
+		};
+
+		pinctrl_sim1_1: sim1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_SAI1_TX_SYNC__SIM1_PORT1_RST_B         0x77
+				MX7D_PAD_SAI1_RX_SYNC__SIM1_PORT1_PD            0x77
+				MX7D_PAD_SAI1_TX_DATA__SIM1_PORT1_SVEN          0x77
+				MX7D_PAD_SAI1_TX_BCLK__SIM1_PORT1_CLK           0x73
+				MX7D_PAD_SAI1_RX_DATA__SIM1_PORT1_TRXD          0x73
+			>;
+		};
+
+	};
+};
+
+&iomuxc_lpsr {
+	imx7d-12x12-lpddr3-val {
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT	0x30
+			>;
+		};
+
+		pinctrl_usbotg1_vbus: usbotg1vbusgrp {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 	  0x14
+			>;
+		};
+
+		pinctrl_usbotg2_vbus: usbotg2vbusgrp {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7    0x14
+			>;
+		};
+
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B 0x74
+			>;
+		};
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	pinctrl-1 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display {
+		bits-per-pixel = <16>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <89>;
+				hfront-porch = <164>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				hsync-len = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&ocrams {
+	fsl,enable-lpsr;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 21 GPIO_ACTIVE_LOW>;
+	power-on-gpio = <&gpio6 19 GPIO_ACTIVE_HIGH>;
+	status = "disabled";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&sim1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_sim1_1>;
+	pinctrl-1 = <&pinctrl_sim1_1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	pinctrl-1 = <&pinctrl_uart1_1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_uart3_1
+		     &pinctrl_bt>;
+	pinctrl-1 = <&pinctrl_uart3_1
+		     &pinctrl_bt>;
+	fsl,uart-has-rtscts;
+	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode;*/
+	/* pinctrl-0 = <&pinctrl_uart3dte_1>; */
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1_1>;
+	pinctrl-1 = <&pinctrl_usdhc1_1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2_1>;
+	pinctrl-1 = <&pinctrl_usdhc2_1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_1_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_1>;
+	cd-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_sd2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3_1>;
+	pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_1>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
diff --git a/arch/arm/dts/imx7d-19x19-ddr3-val.dts b/arch/arm/dts/imx7d-19x19-ddr3-val.dts
new file mode 100644
index 0000000000..47cfaa0ddb
--- /dev/null
+++ b/arch/arm/dts/imx7d-19x19-ddr3-val.dts
@@ -0,0 +1,882 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "i.MX7 DDR3L 19x19 VAL Board";
+	compatible = "fsl,imx7d-19x19-ddr3-val", "fsl,imx7d";
+
+	max7322_reset: max7322-reset {
+		compatible = "gpio-reset";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1>;
+		#reset-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		/* gpios disconnected see resistors R601, R583 */
+		status = "disabled";
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_lcd_reset: lcd-reset {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-reset";
+			gpio = <&gpio3 4 0>;
+			enable-active-high;
+		};
+
+		reg_sd2_vmmc: sd2_vmmc{
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD2";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_sd3_vmmc: sd3_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD3";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio6 11 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg1_vbus: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg2_vbus: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_vref_1v8: regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		reg_coedc_5v: coedc_5v {
+			compatible = "regulator-fixed";
+			regulator-name = "CODEC_5V";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_aud_3v3: aud_3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "AUD_3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_aud_1v8: aud_1v8 {
+			compatible = "regulator-fixed";
+			regulator-name = "AUD_1V8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+	};
+
+	pxp_v4l2_out {
+		compatible = "fsl,imx7d-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2";
+		status = "okay";
+	};
+
+	memory {
+		reg = <0x80000000 0x80000000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&adc2 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&ecspi1 {
+	    fsl,spi-num-chipselects = <1>;
+		cs-gpios = <&gpio4 19 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_cs_1>;
+		status = "okay";
+
+	    flash: at45@0 {
+	        #address-cells = <1>;
+	        #size-cells = <1>;
+	        compatible = "atmel,at45", "jedec,spi-nor";
+	        spi-max-frequency = <20000000>;
+	        reg = <0>;
+	    };
+};
+
+&epxp {
+        status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	pinctrl-assert-gpios = <&max7322 0 GPIO_ACTIVE_HIGH>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+
+		ethphy1: ethernet-phy@5 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <5>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	pinctrl-assert-gpios = <&max7322 0 GPIO_ACTIVE_HIGH>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+	pinctrl-1 = <&pinctrl_i2c1_1_gpio>;
+	scl-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pfuze3000@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2_1>;
+	pinctrl-1 = <&pinctrl_i2c2_1_gpio>;
+	scl-gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3_1>;
+	pinctrl-1 = <&pinctrl_i2c3_1_gpio>;
+	scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	max7322: gpio@68 {
+		compatible = "maxim,max7322";
+		reg = <0x68>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		resets = <&max7322_reset>;
+	};
+	codec: wm8958@1a {
+		compatible = "wlf,wm8958";
+		reg = <0x1a>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>,
+		       <&clks IMX7D_CLK_DUMMY>;
+		clock-names = "mclk1", "mclk2";
+
+		DBVDD1-supply = <&reg_aud_1v8>;
+		DBVDD2-supply = <&reg_aud_1v8>;
+		DBVDD3-supply = <&reg_aud_3v3>;
+		AVDD2-supply = <&reg_aud_1v8>;
+		CPVDD-supply = <&reg_aud_1v8>;
+		SPKVDD1-supply = <&reg_coedc_5v>;
+		SPKVDD2-supply = <&reg_coedc_5v>;
+
+		wlf,ldo1ena;
+		wlf,ldo2ena;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_1 &pinctrl_hog_sd3_vselect>;
+
+	imx7d-19x19-ddr3-val {
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO12__SD2_VSELECT   0x59
+				MX7D_PAD_SD2_CD_B__GPIO5_IO9       0x59
+				MX7D_PAD_SD2_WP__GPIO5_IO10        0x59
+				MX7D_PAD_SD2_RESET_B__GPIO5_IO11   0x59
+				MX7D_PAD_SD3_RESET_B__GPIO6_IO11   0x59
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14    0x59
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15    0x59
+				MX7D_PAD_SD3_STROBE__GPIO6_IO10    0x59
+
+				MX7D_PAD_I2C4_SCL__GPIO4_IO14	  0x7F
+				MX7D_PAD_I2C4_SDA__GPIO4_IO15     0x7F
+			>;
+		};
+
+		pinctrl_hog_sd3_vselect: hoggrp_sd3vselect {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO13__SD3_VSELECT   0x59
+			>;
+		};
+
+		pinctrl_csi: csigrp-1 {
+			fsl,pins = <
+				MX7D_PAD_LCD_DATA04__CSI_VSYNC 	0x0F
+				MX7D_PAD_LCD_DATA05__CSI_HSYNC 	0x0F
+				MX7D_PAD_LCD_DATA06__CSI_PIXCLK 0x0F
+				MX7D_PAD_LCD_DATA07__CSI_MCLK 	0x0F
+				MX7D_PAD_LCD_DATA08__CSI_DATA9 	0x0F
+				MX7D_PAD_LCD_DATA09__CSI_DATA8 	0x0F
+				MX7D_PAD_LCD_DATA10__CSI_DATA7 	0x0F
+				MX7D_PAD_LCD_DATA11__CSI_DATA6 	0x0F
+				MX7D_PAD_LCD_DATA12__CSI_DATA5 	0x0F
+				MX7D_PAD_LCD_DATA13__CSI_DATA4 	0x0F
+				MX7D_PAD_LCD_DATA14__CSI_DATA3 	0x0F
+				MX7D_PAD_LCD_DATA15__CSI_DATA2 	0x0F
+				MX7D_PAD_LCD_DATA02__GPIO3_IO7 	0x0F
+				MX7D_PAD_LCD_DATA03__GPIO3_IO8 	0x0F
+			>;
+		};
+
+		pinctrl_ecspi1_cs_1: ecspi1_cs_grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ECSPI1_SS0__GPIO4_IO19 	0x2
+			>;
+		};
+
+		pinctrl_ecspi1_1: ecspi1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK 	0x2
+				MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI 	0x2
+				MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO 	0x2
+			>;
+		};
+
+		pinctrl_enet1: enet1grp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3
+				MX7D_PAD_GPIO1_IO11__ENET1_MDC  0x3
+				MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1
+				MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1
+				MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1
+				MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1
+				MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1
+				MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1
+				MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1
+				MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1
+				MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1
+				MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1
+				MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1
+				MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1
+			>;
+		};
+
+		pinctrl_enet2: enet2grp {
+			fsl,pins = <
+				MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC	0x1
+				MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0	0x1
+				MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1	0x1
+				MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2	0x1
+				MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3	0x1
+				MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL	0x1
+				MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC	0x1
+				MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0	0x1
+				MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1	0x1
+				MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2	0x1
+				MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3	0x1
+				MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL	0x1
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x32
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x32
+			>;
+		};
+
+		pinctrl_i2c1_1: i2c1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__I2C1_SDA          0x4000007f
+				MX7D_PAD_I2C1_SCL__I2C1_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c1_1_gpio: i2c1grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__GPIO4_IO9          0x7f
+				MX7D_PAD_I2C1_SCL__GPIO4_IO8          0x7f
+			>;
+		};
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__I2C2_SDA          0x4000007f
+				MX7D_PAD_I2C2_SCL__I2C2_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c2_1_gpio: i2c2grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__GPIO4_IO11          0x7f
+				MX7D_PAD_I2C2_SCL__GPIO4_IO10          0x7f
+			>;
+		};
+
+		pinctrl_i2c3_1: i2c3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C3_SDA__I2C3_SDA	     0x4000007f
+				MX7D_PAD_I2C3_SCL__I2C3_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c3_1_gpio: i2c3grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C3_SDA__GPIO4_IO13          0x7f
+				MX7D_PAD_I2C3_SCL__GPIO4_IO12          0x7f
+			>;
+		};
+
+		pinctrl_i2c4_1: i2c4grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C4_SDA__I2C4_SDA          0x4000007f
+				MX7D_PAD_I2C4_SCL__I2C4_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_lcdif_dat: lcdifdatgrp {
+			fsl,pins = <
+				MX7D_PAD_LCD_DATA00__LCD_DATA0	0x79
+				MX7D_PAD_LCD_DATA01__LCD_DATA1	0x79
+				MX7D_PAD_LCD_DATA02__LCD_DATA2	0x79
+				MX7D_PAD_LCD_DATA03__LCD_DATA3	0x79
+				MX7D_PAD_LCD_DATA04__LCD_DATA4	0x79
+				MX7D_PAD_LCD_DATA05__LCD_DATA5	0x79
+				MX7D_PAD_LCD_DATA06__LCD_DATA6	0x79
+				MX7D_PAD_LCD_DATA07__LCD_DATA7	0x79
+				MX7D_PAD_LCD_DATA08__LCD_DATA8	0x79
+				MX7D_PAD_LCD_DATA09__LCD_DATA9	0x79
+				MX7D_PAD_LCD_DATA10__LCD_DATA10	0x79
+				MX7D_PAD_LCD_DATA11__LCD_DATA11	0x79
+				MX7D_PAD_LCD_DATA12__LCD_DATA12	0x79
+				MX7D_PAD_LCD_DATA13__LCD_DATA13	0x79
+				MX7D_PAD_LCD_DATA14__LCD_DATA14	0x79
+				MX7D_PAD_LCD_DATA15__LCD_DATA15	0x79
+				MX7D_PAD_LCD_DATA16__LCD_DATA16	0x79
+				MX7D_PAD_LCD_DATA17__LCD_DATA17	0x79
+				MX7D_PAD_LCD_DATA18__LCD_DATA18	0x79
+				MX7D_PAD_LCD_DATA19__LCD_DATA19	0x79
+				MX7D_PAD_LCD_DATA20__LCD_DATA20	0x79
+				MX7D_PAD_LCD_DATA21__LCD_DATA21	0x79
+				MX7D_PAD_LCD_DATA22__LCD_DATA22	0x79
+				MX7D_PAD_LCD_DATA23__LCD_DATA23	0x79
+			>;
+		};
+
+		pinctrl_lcdif_ctrl: lcdifctrlgrp {
+			fsl,pins = <
+				MX7D_PAD_LCD_CLK__LCD_CLK	0x79
+				MX7D_PAD_LCD_ENABLE__LCD_ENABLE	0x79
+				MX7D_PAD_LCD_VSYNC__LCD_VSYNC	0x79
+				MX7D_PAD_LCD_HSYNC__LCD_HSYNC	0x79
+			>;
+		};
+
+		pinctrl_sai1: sai1grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+				MX7D_PAD_SAI1_TX_BCLK__SAI1_TX_BCLK     0x1f
+				MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC     0x1f
+				MX7D_PAD_SAI1_RX_SYNC__SAI1_RX_SYNC     0x1f
+				MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0    0x1f
+				MX7D_PAD_SAI1_TX_DATA__SAI1_TX_DATA0    0
+			>;
+		};
+
+		pinctrl_sai2: sai2grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+				MX7D_PAD_SAI2_TX_BCLK__SAI2_TX_BCLK     0x1f
+				MX7D_PAD_SAI2_TX_SYNC__SAI2_TX_SYNC     0x1f
+				MX7D_PAD_SAI2_RX_DATA__SAI2_RX_DATA0    0x1f
+				MX7D_PAD_SAI2_TX_DATA__SAI2_TX_DATA0    0
+				MX7D_PAD_GPIO1_IO13__GPIO1_IO13		0x59
+			>;
+		};
+
+		pinctrl_uart1_1: uart1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+			>;
+		};
+
+		pinctrl_uart3_1: uart3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS	0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS	0x79
+			>;
+		};
+
+		pinctrl_uart3dte_1: uart3dtegrp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS	0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DTE_RTS	0x79
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x59
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x19
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x59
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x59
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x59
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x59
+				MX7D_PAD_ECSPI2_SCLK__SD1_DATA4 0x59
+				MX7D_PAD_ECSPI2_MOSI__SD1_DATA5 0x59
+				MX7D_PAD_ECSPI2_MISO__SD1_DATA6 0x59
+				MX7D_PAD_ECSPI2_SS0__SD1_DATA7  0x59
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     0x59
+				MX7D_PAD_SD2_CLK__SD2_CLK     0x19
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 0x59
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 0x59
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 0x59
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 0x59
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     0x5a
+				MX7D_PAD_SD2_CLK__SD2_CLK     0x1a
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5a
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5a
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5a
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5a
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD2_CMD__SD2_CMD     0x5b
+				MX7D_PAD_SD2_CLK__SD2_CLK     0x1b
+				MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5b
+				MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5b
+				MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5b
+				MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5b
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD     0x59
+				MX7D_PAD_SD3_CLK__SD3_CLK     0x19
+				MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
+				MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
+				MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
+				MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
+				MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
+				MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
+				MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
+				MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD     0x5a
+				MX7D_PAD_SD3_CLK__SD3_CLK     0x1a
+				MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5a
+				MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5a
+				MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5a
+				MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5a
+				MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5a
+				MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5a
+				MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5a
+				MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5a
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD3_CMD__SD3_CMD     0x5b
+				MX7D_PAD_SD3_CLK__SD3_CLK     0x1b
+				MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5b
+				MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5b
+				MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5b
+				MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5b
+				MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5b
+				MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5b
+				MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5b
+				MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5b
+			>;
+		};
+		
+		pinctrl_qspi1_1: qspi1grp_1 {
+			fsl,pins = <
+				MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 0x51
+				MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 0x51
+				MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 0x51
+				MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 0x51
+				MX7D_PAD_EPDC_DATA04__QSPI_A_DQS 0x51
+				MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK 0x51
+				MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B 0x51
+				MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B 0x51
+				MX7D_PAD_EPDC_DATA08__QSPI_B_DATA0 0x51
+				MX7D_PAD_EPDC_DATA09__QSPI_B_DATA1 0x51
+				MX7D_PAD_EPDC_DATA10__QSPI_B_DATA2 0x51
+				MX7D_PAD_EPDC_DATA11__QSPI_B_DATA3 0x51
+				MX7D_PAD_EPDC_DATA12__QSPI_B_DQS 0x51
+				MX7D_PAD_EPDC_DATA13__QSPI_B_SCLK 0x51
+				MX7D_PAD_EPDC_DATA14__QSPI_B_SS0_B 0x51
+				MX7D_PAD_EPDC_DATA15__QSPI_B_SS1_B 0x51
+			>;
+		};
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-19x19-ddr3-val {
+		pinctrl_hog_2: hoggrp-2 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3 0x80000000
+				MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x80000000
+			>;
+		};
+
+		pinctrl_mipi_csi: mipicsigrp-1 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO01__ANATOP_24M_OUT 0x3
+			>;
+		};
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display {
+		bits-per-pixel = <16>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <89>;
+				hfront-porch = <164>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				hsync-len = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	status = "disabled";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "disabled";
+};
+
+&sdma {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_1>;
+	fsl,uart-has-rtscts;
+	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode;*/
+	pinctrl-0 = <&pinctrl_uart3dte_1>;
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	cd-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	tuning-step = <2>;
+	vmmc-supply = <&reg_sd2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	cd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	tuning-step = <2>;
+	vmmc-supply = <&reg_sd3_vmmc>;
+	status = "okay";
+};
+
+&qspi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_qspi1_1>;
+	pinctrl-1 = <&pinctrl_qspi1_1>;
+	status = "okay";
+	fsl,qspi-has-second-chip = <1>;
+	ddrsmp=<0>;
+
+	flash0: n25q512ax3@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q512ax3", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <0>;
+	};
+
+	flash1: n25q512ax3@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q512ax3", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <1>;
+	};
+
+	flash2: n25q512ax3@2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q512ax3", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <2>;
+	};
+
+	flash3: n25q512ax3@3 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q512ax3", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+		spi-nor,ddr-quad-read-dummy = <6>;
+		reg = <3>;
+	};
+};
\ No newline at end of file
diff --git a/arch/arm/dts/imx7d-19x19-lpddr2-val.dts b/arch/arm/dts/imx7d-19x19-lpddr2-val.dts
new file mode 100644
index 0000000000..2475ad46b9
--- /dev/null
+++ b/arch/arm/dts/imx7d-19x19-lpddr2-val.dts
@@ -0,0 +1,395 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "i.MX7D LPDDR2 19x19 VAL Board";
+	compatible = "fsl,imx7d-19x19-lpddr2-val", "fsl,imx7d";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_sd1_vmmc: sd1_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD1";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg1_vbus: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg2_vbus: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_vref_1v8: regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+	pinctrl-1 = <&pinctrl_i2c1_1_gpio>;
+	scl-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pfuze3000@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2_1>;
+	pinctrl-1 = <&pinctrl_i2c2_1_gpio>;
+	scl-gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_1>;
+
+	imx7d-19x19-lpddr3-val {
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C4_SCL__GPIO4_IO14	   0x80000000
+
+				MX7D_PAD_SD1_CD_B__GPIO5_IO0 		0x59
+				MX7D_PAD_SD1_WP__GPIO5_IO1 			0x59
+				MX7D_PAD_SD1_RESET_B__GPIO5_IO2 	0x59
+
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14    	0x59
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15    	0x59
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x32
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x32
+			>;
+		};
+
+		pinctrl_gpmi_nand_1: gpmi-nand-1 {
+			fsl,pins = <
+				MX7D_PAD_SD3_CLK__NAND_CLE			0x71
+				MX7D_PAD_SD3_CMD__NAND_ALE			0x71
+				MX7D_PAD_SAI1_MCLK__NAND_WP_B		0x71
+				MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
+				MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B	0x71
+				MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
+				MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
+				MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+				MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
+				MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
+				MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
+				MX7D_PAD_SD3_DATA3__NAND_DATA03		0x71
+				MX7D_PAD_SD3_DATA4__NAND_DATA04		0x71
+				MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
+				MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
+				MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
+			>;
+		};
+
+		pinctrl_i2c1_1: i2c1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__I2C1_SDA          0x4000007f
+				MX7D_PAD_I2C1_SCL__I2C1_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c1_1_gpio: i2c1grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__GPIO4_IO9          0x7f
+				MX7D_PAD_I2C1_SCL__GPIO4_IO8          0x7f
+			>;
+		};
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__I2C2_SDA          0x4000007f
+				MX7D_PAD_I2C2_SCL__I2C2_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c2_1_gpio: i2c2grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__GPIO4_IO11          0x7f
+				MX7D_PAD_I2C2_SCL__GPIO4_IO10          0x7f
+			>;
+		};
+
+		pinctrl_uart1_1: uart1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+			>;
+		};
+
+		pinctrl_uart3_1: uart3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS		0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS		0x79
+			>;
+		};
+
+		pinctrl_uart3dte_1: uart3dtegrp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS		0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DTE_RTS		0x79
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x59
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x19
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x59
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x59
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x59
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x59
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x5a
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x1a
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5a
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5a
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5a
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5a
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x5b
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x1b
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5b
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5b
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5b
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5b
+			>;
+		};
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-19x19-lpddr3-val {
+		pinctrl_hog_2: hoggrp-2 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3 0x14
+				MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x14
+				MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x14
+			>;
+		};
+	};
+};
+
+&sdma {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_1>;
+	fsl,uart-has-rtscts;
+	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode;*/
+	pinctrl-0 = <&pinctrl_uart3dte_1>;
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx7d-19x19-lpddr3-val.dts b/arch/arm/dts/imx7d-19x19-lpddr3-val.dts
new file mode 100644
index 0000000000..eda09a592f
--- /dev/null
+++ b/arch/arm/dts/imx7d-19x19-lpddr3-val.dts
@@ -0,0 +1,402 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "i.MX7 LPDDR3 19x19 VAL Board";
+	compatible = "fsl,imx7d-19x19-lpddr3-val", "fsl,imx7d";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_sd1_vmmc: sd1_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_SD1";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg1_vbus: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_otg2_vbus: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_vref_1v8: regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	memory {
+		reg = <0x80000000 0x80000000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand_1>;
+	status = "okay";
+	nand-on-flash-bbt;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+	pinctrl-1 = <&pinctrl_i2c1_1_gpio>;
+	scl-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pfuze3000@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2_1>;
+	pinctrl-1 = <&pinctrl_i2c2_1_gpio>;
+	scl-gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_1>;
+
+	imx7d-19x19-lpddr3-val {
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C4_SCL__GPIO4_IO14	   0x80000000
+
+				MX7D_PAD_SD1_CD_B__GPIO5_IO0 		0x59
+				MX7D_PAD_SD1_WP__GPIO5_IO1 			0x59
+				MX7D_PAD_SD1_RESET_B__GPIO5_IO2 	0x59
+
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14    	0x59
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15    	0x59
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x32
+				MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x32
+			>;
+		};
+
+		pinctrl_gpmi_nand_1: gpmi-nand-1 {
+			fsl,pins = <
+				MX7D_PAD_SD3_CLK__NAND_CLE			0x71
+				MX7D_PAD_SD3_CMD__NAND_ALE			0x71
+				MX7D_PAD_SAI1_MCLK__NAND_WP_B		0x71
+				MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
+				MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B	0x71
+				MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
+				MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
+				MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+				MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
+				MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
+				MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
+				MX7D_PAD_SD3_DATA3__NAND_DATA03		0x71
+				MX7D_PAD_SD3_DATA4__NAND_DATA04		0x71
+				MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
+				MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
+				MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
+			>;
+		};
+
+		pinctrl_i2c1_1: i2c1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__I2C1_SDA          0x4000007f
+				MX7D_PAD_I2C1_SCL__I2C1_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c1_1_gpio: i2c1grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C1_SDA__GPIO4_IO9          0x7f
+				MX7D_PAD_I2C1_SCL__GPIO4_IO8          0x7f
+			>;
+		};
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__I2C2_SDA          0x4000007f
+				MX7D_PAD_I2C2_SCL__I2C2_SCL          0x4000007f
+			>;
+		};
+
+		pinctrl_i2c2_1_gpio: i2c2grp-1-gpio {
+			fsl,pins = <
+				MX7D_PAD_I2C2_SDA__GPIO4_IO11          0x7f
+				MX7D_PAD_I2C2_SCL__GPIO4_IO10          0x7f
+			>;
+		};
+
+		pinctrl_uart1_1: uart1grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
+				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79
+			>;
+		};
+
+		pinctrl_uart3_1: uart3grp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS		0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS		0x79
+			>;
+		};
+
+		pinctrl_uart3dte_1: uart3dtegrp-1 {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79
+				MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79
+				MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS		0x79
+				MX7D_PAD_UART3_CTS_B__UART3_DTE_RTS		0x79
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x59
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x19
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x59
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x59
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x59
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x59
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x5a
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x1a
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5a
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5a
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5a
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5a
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD       0x5b
+				MX7D_PAD_SD1_CLK__SD1_CLK       0x1b
+				MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5b
+				MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5b
+				MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5b
+				MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5b
+			>;
+		};
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-19x19-lpddr3-val {
+		pinctrl_hog_2: hoggrp-2 {
+			fsl,pins = <
+				MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3 0x14
+				MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x14
+				MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x14
+			>;
+		};
+	};
+};
+
+&sdma {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_1>;
+	fsl,uart-has-rtscts;
+	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode;*/
+	pinctrl-0 = <&pinctrl_uart3dte_1>;
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/mach-imx/mx7/Kconfig b/arch/arm/mach-imx/mx7/Kconfig
index 72f069b401..be32f8052c 100644
--- a/arch/arm/mach-imx/mx7/Kconfig
+++ b/arch/arm/mach-imx/mx7/Kconfig
@@ -50,6 +50,46 @@ config TARGET_MX7DSABRESD
 	select MX7D
 	imply CMD_DM
 
+config TARGET_MX7D_12X12_LPDDR3_VAL
+	bool "Support mx7d_12x12_lpddr3_val"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+	imply CMD_DM
+
+config TARGET_MX7D_12X12_DDR3_VAL
+	bool "Support mx7d_12x12_ddr3_val"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+	imply CMD_DM
+
+config TARGET_MX7D_19X19_DDR3_VAL
+	bool "Support mx7d_19x19_ddr3_val"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+	imply CMD_DM
+
+config TARGET_MX7D_19X19_LPDDR3_VAL
+	bool "Support mx7d_19x19_lpddr3_val"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+	imply CMD_DM
+
+config TARGET_MX7D_19X19_LPDDR2_VAL
+	bool "Support mx7d_19x19_lpddr2_val"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+	imply CMD_DM
+
 config TARGET_PICO_IMX7D
 	bool "pico-imx7d"
 	select BOARD_LATE_INIT
@@ -81,6 +121,10 @@ config SYS_SOC
 
 source "board/compulab/cl-som-imx7/Kconfig"
 source "board/freescale/mx7dsabresd/Kconfig"
+source "board/freescale/mx7d_12x12_lpddr3_val/Kconfig"
+source "board/freescale/mx7d_12x12_ddr3_val/Kconfig"
+source "board/freescale/mx7d_19x19_ddr3_val/Kconfig"
+source "board/freescale/mx7d_19x19_lpddr3_val/Kconfig"
 source "board/novtech/meerkat96/Kconfig"
 source "board/technexion/pico-imx7d/Kconfig"
 source "board/toradex/colibri_imx7/Kconfig"
diff --git a/board/freescale/mx7d_12x12_ddr3_val/Kconfig b/board/freescale/mx7d_12x12_ddr3_val/Kconfig
new file mode 100644
index 0000000000..efe29ed8be
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_MX7D_12X12_DDR3_VAL
+
+config SYS_BOARD
+	default "mx7d_12x12_ddr3_val"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "mx7d_12x12_ddr3_val"
+
+config SYS_TEXT_BASE
+	default 0x87800000
+endif
diff --git a/board/freescale/mx7d_12x12_ddr3_val/Makefile b/board/freescale/mx7d_12x12_ddr3_val/Makefile
new file mode 100644
index 0000000000..21985cfe56
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2015 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx7d_12x12_ddr3_val.o
diff --git a/board/freescale/mx7d_12x12_ddr3_val/imximage.cfg b/board/freescale/mx7d_12x12_ddr3_val/imximage.cfg
new file mode 100644
index 0000000000..8c2adfc826
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/imximage.cfg
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * sd/onenand, nor
+ */
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_12x12_ddr3_arm2/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000b24
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+
+#endif
diff --git a/board/freescale/mx7d_12x12_ddr3_val/imximage_TO_1_1.cfg b/board/freescale/mx7d_12x12_ddr3_val/imximage_TO_1_1.cfg
new file mode 100644
index 0000000000..89a1425944
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/imximage_TO_1_1.cfg
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * sd/onenand, nor
+ */
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_12x12_ddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30360070 0x00703021
+DATA 4 0x30360090 0x0
+DATA 4 0x30360070 0x00603021
+CHECK_BITS_SET 4 0x30360070 0x80000000
+DATA 4 0x30389880 0x1
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000dee
+DATA 4 0x3079007c 0x18181818
+DATA 4 0x30790080 0x18181818
+DATA 4 0x30790084 0x40401818
+DATA 4 0x30790088 0x00000040
+DATA 4 0x3079006c 0x40404040
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+
+#endif
diff --git a/board/freescale/mx7d_12x12_ddr3_val/mx7d_12x12_ddr3_val.c b/board/freescale/mx7d_12x12_ddr3_val/mx7d_12x12_ddr3_val.c
new file mode 100644
index 0000000000..cb83f83574
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/mx7d_12x12_ddr3_val.c
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#include <asm/arch/crm_regs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+#define SPI_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX7D_PAD_SD1_RESET_B__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_SD1_WP__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_SD1_CD_B__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	/* Chip selects CS0:CS3 */
+	MX7D_PAD_SD1_CLK__GPIO5_IO3 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_SD1_CMD__GPIO5_IO4 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_SD1_DATA0__GPIO5_IO5 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_SD1_DATA1__GPIO5_IO6 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void setup_spinor(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+					 ARRAY_SIZE(ecspi1_pads));
+	gpio_request(IMX_GPIO_NR(5, 3), "ecspi1_cs");
+	gpio_direction_output(IMX_GPIO_NR(5, 3), 0);
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 3 && cs == 0) ? (IMX_GPIO_NR(5, 3)) : -1;
+}
+#endif
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+	setup_spinor();
+#endif
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x10, 0x22, 0x00, 0x00)},
+	{"sd3", MAKE_CFGVAL(0x10, 0x1a, 0x00, 0x00)},
+	{NULL,   0},
+};
+#endif
+
+#ifdef CONFIG_DM_PMIC
+int power_init_board(void)
+{
+	struct udevice *dev;
+	int ret, dev_id, rev_id, reg;
+
+	ret = pmic_get("pfuze3000@8", &dev);
+	if (ret == -ENODEV)
+		return 0;
+	if (ret != 0)
+		return ret;
+
+	dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+	rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	reg = pmic_reg_read(dev, PFUZE3000_LDOGCTL);
+	reg |= 0x1;
+	pmic_reg_write(dev, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(dev, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 0.975V */
+	reg = 0xb;
+	pmic_reg_write(dev, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BSTBY, reg);
+
+	/* set SW1B normal voltage to 0.975V */
+	reg = pmic_reg_read(dev, PFUZE3000_SW1BVOLT);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(9750);
+	pmic_reg_write(dev, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+	puts("Board: MX7D 12x12 DDR3 VAL\n");
+
+	return 0;
+}
diff --git a/board/freescale/mx7d_12x12_ddr3_val/plugin.S b/board/freescale/mx7d_12x12_ddr3_val/plugin.S
new file mode 100644
index 0000000000..f1980b8879
--- /dev/null
+++ b/board/freescale/mx7d_12x12_ddr3_val/plugin.S
@@ -0,0 +1,227 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+/* DDR script */
+.macro imx7d_ddrphy_latency_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne NO_DELAY
+
+	/*TO 1.1*/
+	ldr r1, =0x00000dee
+	str r1, [r0, #0x9c]
+	ldr r1, =0x18181818
+	str r1, [r0, #0x7c]
+	ldr r1, =0x18181818
+	str r1, [r0, #0x80]
+	ldr r1, =0x40401818
+	str r1, [r0, #0x84]
+	ldr r1, =0x00000040
+	str r1, [r0, #0x88]
+	ldr r1, =0x40404040
+	str r1, [r0, #0x6c]
+	b TUNE_END
+
+NO_DELAY:
+	/*TO 1.0*/
+	ldr r1, =0x00000b24
+	str r1, [r0, #0x9c]
+
+TUNE_END:
+.endm
+
+.macro imx7d_ddr_freq_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne FREQ_DEFAULT_533
+
+	/* Change to 400Mhz for TO1.1 */
+	ldr r0, =ANATOP_BASE_ADDR
+	ldr r1, =0x70
+	ldr r2, =0x00703021
+	str r2, [r0, r1]
+	ldr r1, =0x90
+	ldr r2, =0x0
+	str r2, [r0, r1]
+	ldr r1, =0x70
+	ldr r2, =0x00603021
+	str r2, [r0, r1]
+
+	ldr r3, =0x80000000
+wait_lock:
+	ldr r2, [r0, r1]
+	and r2, r3
+	cmp r2, r3
+	bne wait_lock
+
+	ldr r0, =CCM_BASE_ADDR
+	ldr r1, =0x9880
+	ldr r2, =0x1
+	str r2, [r0, r1]
+
+FREQ_DEFAULT_533:
+.endm
+
+.macro imx7d_12x12_ddr3_val_ddr_setting
+	imx7d_ddr_freq_setting
+
+	/* Configure ocram_epdc */
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0x4f400005
+	str r1, [r0, #0x4]
+
+	/* clear/set bit30 of SNVS_MISC_CTRL to ensure exit from ddr retention */
+	ldr r0, =ANATOP_BASE_ADDR
+	ldr r1, =(0x1 << 30)
+	str r1, [r0, #0x388]
+	str r1, [r0, #0x384]
+
+	ldr r0, =SRC_BASE_ADDR
+	ldr r1, =0x2
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+	ldr r1, =0x01040001
+	str r1, [r0]
+	ldr r1, =0x80400003
+	str r1, [r0, #0x1a0]
+	ldr r1, =0x00100020
+	str r1, [r0, #0x1a4]
+	ldr r1, =0x80100004
+	str r1, [r0, #0x1a8]
+	ldr r1, =0x00400046
+	str r1, [r0, #0x64]
+	ldr r1, =0x1
+	str r1, [r0, #0x490]
+	ldr r1, =0x00020001
+	str r1, [r0, #0xd0]
+	ldr r1, =0x00690000
+	str r1, [r0, #0xd4]
+	ldr r1, =0x09300004
+	str r1, [r0, #0xdc]
+	ldr r1, =0x04080000
+	str r1, [r0, #0xe0]
+	ldr r1, =0x00100004
+	str r1, [r0, #0xe4]
+	ldr r1, =0x33f
+	str r1, [r0, #0xf4]
+	ldr r1, =0x09081109
+	str r1, [r0, #0x100]
+	ldr r1, =0x0007020d
+	str r1, [r0, #0x104]
+	ldr r1, =0x03040407
+	str r1, [r0, #0x108]
+	ldr r1, =0x00002006
+	str r1, [r0, #0x10c]
+	ldr r1, =0x04020205
+	str r1, [r0, #0x110]
+	ldr r1, =0x03030202
+	str r1, [r0, #0x114]
+	ldr r1, =0x00000803
+	str r1, [r0, #0x120]
+	ldr r1, =0x00800020
+	str r1, [r0, #0x180]
+	ldr r1, =0x02000100
+	str r1, [r0, #0x184]
+	ldr r1, =0x02098204
+	str r1, [r0, #0x190]
+	ldr r1, =0x00030303
+	str r1, [r0, #0x194]
+
+	ldr r1, =0x00000016
+	str r1, [r0, #0x200]
+	ldr r1, =0x00080808
+	str r1, [r0, #0x204]
+	ldr r1, =0x00000f0f
+	str r1, [r0, #0x210]
+	ldr r1, =0x07070707
+	str r1, [r0, #0x214]
+	ldr r1, =0x0f070707
+	str r1, [r0, #0x218]
+
+	ldr r1, =0x06000604
+	str r1, [r0, #0x240]
+	ldr r1, =0x00000001
+	str r1, [r0, #0x244]
+
+	ldr r0, =SRC_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x17420f40
+	str r1, [r0]
+	ldr r1, =0x10210100
+	str r1, [r0, #0x4]
+	ldr r1, =0x00060807
+	str r1, [r0, #0x10]
+	ldr r1, =0x1010007e
+	str r1, [r0, #0xb0]
+	imx7d_ddrphy_latency_setting
+	ldr r1, =0x08080808
+	str r1, [r0, #0x20]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x30]
+	ldr r1, =0x01000010
+	str r1, [r0, #0x50]
+
+	ldr r1, =0x0e407304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e447304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e447306
+	str r1, [r0, #0xc0]
+
+wait_zq:
+	ldr r1, [r0, #0xc4]
+	tst r1, #0x1
+	beq wait_zq
+
+	ldr r1, =0x0e407304
+	str r1, [r0, #0xc0]
+
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	mov r1, #0x178
+	str r1, [r0, #0x20]
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x2
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x0000000f
+	str r1, [r0, #0x18]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+wait_stat:
+	ldr r1, [r0, #0x4]
+	tst r1, #0x1
+	beq wait_stat
+.endm
+
+.macro imx7_clock_gating
+.endm
+
+.macro imx7_qos_setting
+.endm
+
+.macro imx7_ddr_setting
+	imx7d_12x12_ddr3_val_ddr_setting
+.endm
+
+/* include the common plugin code here */
+#include <asm/arch/mx7_plugin.S>
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/Kconfig b/board/freescale/mx7d_12x12_lpddr3_val/Kconfig
new file mode 100644
index 0000000000..31ede4d88c
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_MX7D_12X12_LPDDR3_VAL
+
+config SYS_BOARD
+	default "mx7d_12x12_lpddr3_val"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "mx7d_12x12_lpddr3_val"
+
+config SYS_TEXT_BASE
+	default 0x87800000
+endif
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/Makefile b/board/freescale/mx7d_12x12_lpddr3_val/Makefile
new file mode 100644
index 0000000000..ca48fa0b95
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2015 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx7d_12x12_lpddr3_val.o
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg b/board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg
new file mode 100644
index 0000000000..5d650b2a5e
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_12x12_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040008
+DATA 4 0x307a0064 0x00200038
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00dc 0x00c3000a
+DATA 4 0x307a00e0 0x00010000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0a0e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x03060708
+DATA 4 0x307a010c 0x00a0500c
+DATA 4 0x307a0110 0x05020307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098205
+DATA 4 0x307a0194 0x00060303
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00090909
+DATA 4 0x307a0210 0x00000f00
+DATA 4 0x307a0214 0x08080808
+DATA 4 0x307a0218 0x0f0f0808
+
+DATA 4 0x307a0240 0x06000600
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421e40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x0007080c
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009c 0x00000b24
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x30790018 0x0000000f
+DATA 4 0x307900c0 0x0e487304
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e4c7306
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/imximage_TO_1_1.cfg b/board/freescale/mx7d_12x12_lpddr3_val/imximage_TO_1_1.cfg
new file mode 100644
index 0000000000..76de211a2d
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/imximage_TO_1_1.cfg
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_12x12_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040008
+DATA 4 0x307a0064 0x00200038
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00dc 0x00c3000a
+DATA 4 0x307a00e0 0x00010000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0a0e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x03060708
+DATA 4 0x307a010c 0x00a0500c
+DATA 4 0x307a0110 0x05020307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098205
+DATA 4 0x307a0194 0x00060303
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00090909
+DATA 4 0x307a0210 0x00000f00
+DATA 4 0x307a0214 0x08080808
+DATA 4 0x307a0218 0x0f0f0808
+
+DATA 4 0x307a0240 0x06000601
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421e40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x0007080c
+DATA 4 0x3079007c 0x1c1c1c1c
+DATA 4 0x30790080 0x1c1c1c1c
+DATA 4 0x30790084 0x30301c1c
+DATA 4 0x30790088 0x00000030
+DATA 4 0x3079006c 0x30303030
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009c 0x0db60d6e
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x30790018 0x0000000f
+DATA 4 0x307900c0 0x1e487304
+DATA 4 0x307900c0 0x1e487304
+DATA 4 0x307900c0 0x1e487306
+DATA 4 0x307900c0 0x1e4c7304
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x1e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/mx7d_12x12_lpddr3_val.c b/board/freescale/mx7d_12x12_lpddr3_val/mx7d_12x12_lpddr3_val.c
new file mode 100644
index 0000000000..a55f1483ac
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/mx7d_12x12_lpddr3_val.c
@@ -0,0 +1,651 @@
+/*
+ * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#include <asm/arch/crm_regs.h>
+#include <asm/mach-imx/video.h>
+
+#ifdef CONFIG_VIDEO_MXS
+#include <linux/fb.h>
+#endif
+#if defined(CONFIG_MXC_EPDC)
+#include <lcd.h>
+#include <mxc_epdc_fb.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
+	PAD_CTL_DSE_3P3V_49OHM)
+
+#define QSPI_PAD_CTRL	\
+		(PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define SPI_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define EPDC_PAD_CTRL	0x0
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+#ifdef CONFIG_VIDEO_MXS
+static iomux_v3_cfg_t const lcd_pads[] = {
+	MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA00__LCD_DATA0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA01__LCD_DATA1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA02__LCD_DATA2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA03__LCD_DATA3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA04__LCD_DATA4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA05__LCD_DATA5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA06__LCD_DATA6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA07__LCD_DATA7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA08__LCD_DATA8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA09__LCD_DATA9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA18__LCD_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA19__LCD_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA20__LCD_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA21__LCD_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA22__LCD_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA23__LCD_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+
+	MX7D_PAD_LCD_RESET__GPIO3_IO4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pwm_pads[] = {
+	/* Use GPIO for Brightness adjustment, duty cycle = period */
+	MX7D_PAD_GPIO1_IO01__GPIO1_IO1 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void do_enable_parallel_lcd(struct display_info_t const *dev)
+{
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	imx_iomux_v3_setup_multiple_pads(pwm_pads, ARRAY_SIZE(pwm_pads));
+
+	/* Power up the LCD */
+	gpio_request(IMX_GPIO_NR(3, 4), "lcd_pwr");
+	gpio_direction_output(IMX_GPIO_NR(3, 4) , 1);
+
+	/* Set Brightness to high */
+	gpio_request(IMX_GPIO_NR(1, 1), "lcd_backlight");
+	gpio_direction_output(IMX_GPIO_NR(1, 1) , 1);
+}
+
+struct display_info_t const displays[] = {{
+	.bus = ELCDIF1_IPS_BASE_ADDR,
+	.addr = 0,
+	.pixfmt = 24,
+	.detect = NULL,
+	.enable	= do_enable_parallel_lcd,
+	.mode	= {
+		.name			= "MCIMX28LCD",
+		.xres           = 800,
+		.yres           = 480,
+		.pixclock       = 29850,
+		.left_margin    = 89,
+		.right_margin   = 164,
+		.upper_margin   = 23,
+		.lower_margin   = 10,
+		.hsync_len      = 10,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+#endif
+
+
+static iomux_v3_cfg_t const per_rst_pads[] = {
+	MX7D_PAD_GPIO1_IO03__GPIO1_IO3 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX7D_PAD_GPIO1_IO11__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_GPIO1_IO10__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_TX_CLK__CCM_ENET_REF_CLK1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec1(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_QSPI
+#ifndef CONFIG_DM_SPI
+static iomux_v3_cfg_t const quadspi_pads[] = {
+	MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA04__QSPI_A_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+	MX7D_PAD_EPDC_DATA08__QSPI_B_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA09__QSPI_B_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA10__QSPI_B_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA11__QSPI_B_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA12__QSPI_B_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA13__QSPI_B_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA14__QSPI_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA15__QSPI_B_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+};
+#endif
+
+int board_qspi_init(void)
+{
+#ifndef CONFIG_DM_SPI
+	/* Set the iomux */
+	imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads));
+#endif
+
+	/* Set the clock */
+	set_clk_qspi();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec1();
+
+	ret = fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC1 MXC: %s:failed\n", __func__);
+
+	return 0;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+	int ret;
+
+	/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+		(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
+		 IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
+
+	ret = set_clk_enet(ENET_125MHZ);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* Enable 1.8V(SEL_1P5_1P8_POS_REG) on
+	   Phy control debug reg 0 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	/* rgmii tx clock delay enable */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+
+	/* CS0 */
+	MX7D_PAD_ECSPI1_SS0__GPIO4_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void setup_spinor(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+					 ARRAY_SIZE(ecspi1_pads));
+	gpio_request(IMX_GPIO_NR(4, 19), "ecspi1_cs");
+	gpio_direction_output(IMX_GPIO_NR(4, 19), 0);
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 19)) : -1;
+}
+#endif
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+#ifdef CONFIG_MXC_EPDC
+static iomux_v3_cfg_t const epdc_enable_pads[] = {
+	MX7D_PAD_EPDC_DATA00__EPDC_DATA0	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__EPDC_DATA1	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__EPDC_DATA2	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__EPDC_DATA3	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA04__EPDC_DATA4	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__EPDC_DATA5	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__EPDC_DATA6	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA07__EPDC_DATA7	| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCLK__EPDC_SDCLK		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDLE__EPDC_SDLE		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDOE__EPDC_SDOE		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDSHR__EPDC_SDSHR		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE0__EPDC_SDCE0		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE1__EPDC_SDCE1		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE2__EPDC_SDCE2		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE3__EPDC_SDCE3		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_GDCLK__EPDC_GDCLK		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_GDOE__EPDC_GDOE		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_GDRL__EPDC_GDRL		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_GDSP__EPDC_GDSP		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_BDR0__EPDC_BDR0		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+	MX7D_PAD_EPDC_BDR1__EPDC_BDR1		| MUX_PAD_CTRL(EPDC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const epdc_disable_pads[] = {
+	MX7D_PAD_EPDC_DATA00__GPIO2_IO0,
+	MX7D_PAD_EPDC_DATA01__GPIO2_IO1,
+	MX7D_PAD_EPDC_DATA02__GPIO2_IO2,
+	MX7D_PAD_EPDC_DATA03__GPIO2_IO3,
+	MX7D_PAD_EPDC_DATA04__GPIO2_IO4,
+	MX7D_PAD_EPDC_DATA05__GPIO2_IO5,
+	MX7D_PAD_EPDC_DATA06__GPIO2_IO6,
+	MX7D_PAD_EPDC_DATA07__GPIO2_IO7,
+	MX7D_PAD_EPDC_SDCLK__GPIO2_IO16,
+	MX7D_PAD_EPDC_SDLE__GPIO2_IO17,
+	MX7D_PAD_EPDC_SDOE__GPIO2_IO18,
+	MX7D_PAD_EPDC_SDSHR__GPIO2_IO19,
+	MX7D_PAD_EPDC_SDCE0__GPIO2_IO20,
+	MX7D_PAD_EPDC_SDCE1__GPIO2_IO21,
+	MX7D_PAD_EPDC_SDCE2__GPIO2_IO22,
+	MX7D_PAD_EPDC_SDCE3__GPIO2_IO23,
+	MX7D_PAD_EPDC_GDCLK__GPIO2_IO24,
+	MX7D_PAD_EPDC_GDOE__GPIO2_IO25,
+	MX7D_PAD_EPDC_GDRL__GPIO2_IO26,
+	MX7D_PAD_EPDC_GDSP__GPIO2_IO27,
+	MX7D_PAD_EPDC_BDR0__GPIO2_IO28,
+	MX7D_PAD_EPDC_BDR1__GPIO2_IO29,
+};
+
+vidinfo_t panel_info = {
+	.vl_refresh = 85,
+	.vl_col = 1024,
+	.vl_row = 758,
+	.vl_pixclock = 40000000,
+	.vl_left_margin = 12,
+	.vl_right_margin = 76,
+	.vl_upper_margin = 4,
+	.vl_lower_margin = 5,
+	.vl_hsync = 12,
+	.vl_vsync = 2,
+	.vl_sync = 0,
+	.vl_mode = 0,
+	.vl_flag = 0,
+	.vl_bpix = 3,
+	.cmap = 0,
+};
+
+struct epdc_timing_params panel_timings = {
+	.vscan_holdoff = 4,
+	.sdoed_width = 10,
+	.sdoed_delay = 20,
+	.sdoez_width = 10,
+	.sdoez_delay = 20,
+	.gdclk_hp_offs = 524,
+	.gdsp_offs = 327,
+	.gdoe_offs = 0,
+	.gdclk_offs = 19,
+	.num_ce = 1,
+};
+
+static void setup_epdc_power(void)
+{
+	/* IOMUX_GPR1: bit30: Disable On-chip RAM EPDC Function */
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+		IOMUXC_GPR_GPR1_GPR_ENABLE_OCRAM_EPDC_MASK, 0);
+
+	/* Setup epdc voltage */
+
+	/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
+	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+	gpio_request(IMX_GPIO_NR(2, 31), "epdc_pwrstat");
+	gpio_direction_input(IMX_GPIO_NR(2, 31));
+
+	/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
+	imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+
+	/* Set as output */
+	gpio_request(IMX_GPIO_NR(4, 14), "epdc_vcom0");
+	gpio_direction_output(IMX_GPIO_NR(4, 14), 1);
+
+	/* EPDC_PWRWAKEUP - GPIO4[23] for EPD PMIC WAKEUP */
+	imx_iomux_v3_setup_pad(MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+	/* Set as output */
+	gpio_request(IMX_GPIO_NR(4, 23), "epdc_pwrwakeup");
+	gpio_direction_output(IMX_GPIO_NR(4, 23), 1);
+
+	/* EPDC_PWRCTRL0 - GPIO4[20] for EPD PWR CTL0 */
+	imx_iomux_v3_setup_pad(MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+	/* Set as output */
+	gpio_request(IMX_GPIO_NR(4, 20), "epdc_pwrctrl0");
+	gpio_direction_output(IMX_GPIO_NR(4, 20), 1);
+}
+
+static void epdc_enable_pins(void)
+{
+	/* epdc iomux settings */
+	imx_iomux_v3_setup_multiple_pads(epdc_enable_pads,
+				ARRAY_SIZE(epdc_enable_pads));
+}
+
+static void epdc_disable_pins(void)
+{
+	/* Configure MUX settings for EPDC pins to GPIO  and drive to 0 */
+	imx_iomux_v3_setup_multiple_pads(epdc_disable_pads,
+				ARRAY_SIZE(epdc_disable_pads));
+}
+
+static void setup_epdc(void)
+{
+	/*** epdc Maxim PMIC settings ***/
+
+	/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
+	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+
+	/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
+	imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+
+	/* EPDC_PWRWAKEUP - GPIO4[23] for EPD PMIC WAKEUP */
+	imx_iomux_v3_setup_pad(MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+
+	/* EPDC_PWRCTRL0 - GPIO4[20] for EPD PWR CTL0 */
+	imx_iomux_v3_setup_pad(MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20 |
+				MUX_PAD_CTRL(EPDC_PAD_CTRL));
+
+	/* Set pixel clock rates for EPDC in clock.c */
+
+	panel_info.epdc_data.wv_modes.mode_init = 0;
+	panel_info.epdc_data.wv_modes.mode_du = 1;
+	panel_info.epdc_data.wv_modes.mode_gc4 = 3;
+	panel_info.epdc_data.wv_modes.mode_gc8 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc16 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc32 = 2;
+
+	panel_info.epdc_data.epdc_timings = panel_timings;
+
+	setup_epdc_power();
+}
+
+void epdc_power_on(void)
+{
+	unsigned int reg;
+	struct gpio_regs *gpio_regs = (struct gpio_regs *)GPIO2_BASE_ADDR;
+
+	/* Set EPD_PWR_CTL0 to high - enable EINK_VDD (3.15) */
+	gpio_set_value(IMX_GPIO_NR(4, 20), 1);
+	udelay(1000);
+
+	/* Enable epdc signal pin */
+	epdc_enable_pins();
+
+	/* Set PMIC Wakeup to high - enable Display power */
+	gpio_set_value(IMX_GPIO_NR(4, 23), 1);
+
+	/* Wait for PWRGOOD == 1 */
+	while (1) {
+		reg = readl(&gpio_regs->gpio_psr);
+		if (!(reg & (1 << 31)))
+			break;
+
+		udelay(100);
+	}
+
+	/* Enable VCOM */
+	gpio_set_value(IMX_GPIO_NR(4, 14), 1);
+
+	udelay(500);
+}
+
+void epdc_power_off(void)
+{
+	/* Set PMIC Wakeup to low - disable Display power */
+	gpio_set_value(IMX_GPIO_NR(4, 23), 0);
+
+	/* Disable VCOM */
+	gpio_set_value(IMX_GPIO_NR(4, 14), 0);
+
+	epdc_disable_pins();
+
+	/* Set EPD_PWR_CTL0 to low - disable EINK_VDD (3.15) */
+	gpio_set_value(IMX_GPIO_NR(4, 20), 0);
+}
+#endif
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	/* Reset peripherals */
+	imx_iomux_v3_setup_multiple_pads(per_rst_pads, ARRAY_SIZE(per_rst_pads));
+
+	gpio_request(IMX_GPIO_NR(1, 3), "per_rst");
+	gpio_direction_output(IMX_GPIO_NR(1, 3) , 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 3), 1);
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+	setup_spinor();
+#endif
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+	board_qspi_init();
+#endif
+
+#ifdef	CONFIG_MXC_EPDC
+	setup_epdc();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd1", MAKE_CFGVAL(0x10, 0x12, 0x00, 0x00)},
+	{"sd2", MAKE_CFGVAL(0x10, 0x16, 0x00, 0x00)},
+	{"emmc", MAKE_CFGVAL(0x10, 0x2a, 0x00, 0x00)},
+	{"qspi", MAKE_CFGVAL(0x00, 0x40, 0x00, 0x00)},
+	{NULL,   0},
+};
+#endif
+
+#ifdef CONFIG_DM_PMIC
+int power_init_board(void)
+{
+	struct udevice *dev;
+	int ret, dev_id, rev_id, reg;
+
+	ret = pmic_get("pfuze3000@8", &dev);
+	if (ret == -ENODEV)
+		return 0;
+	if (ret != 0)
+		return ret;
+
+	dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+	rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	reg = pmic_reg_read(dev, PFUZE3000_LDOGCTL);
+	reg |= 0x1;
+	pmic_reg_write(dev, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(dev, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 0.975V */
+	reg = 0xb;
+	pmic_reg_write(dev, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BSTBY, reg);
+
+	/* below are for LPSR mode support */
+	reg = pmic_reg_read(dev, PFUZE3000_SW3MODE);
+	reg |= 0x20;
+	pmic_reg_write(dev, PFUZE3000_SW3MODE, reg);
+
+	reg = pmic_reg_read(dev, PFUZE3000_VLDO1CTL);
+	reg |= 0x80;
+	pmic_reg_write(dev, PFUZE3000_VLDO1CTL, reg);
+
+	reg = pmic_reg_read(dev, PFUZE3000_VLDO3CTL);
+	reg |= 0x80;
+	pmic_reg_write(dev, PFUZE3000_VLDO3CTL, reg);
+
+	reg = pmic_reg_read(dev, PFUZE3000_SW2MODE);
+	reg |= 0x20;
+	pmic_reg_write(dev, PFUZE3000_SW2MODE, reg);
+
+	/* set SW1B normal voltage to 0.975V */
+	reg = pmic_reg_read(dev, PFUZE3000_SW1BVOLT);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(9750);
+	pmic_reg_write(dev, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+	puts("Board: MX7D 12x12 LPDDR3 VAL\n");
+
+	return 0;
+}
diff --git a/board/freescale/mx7d_12x12_lpddr3_val/plugin.S b/board/freescale/mx7d_12x12_lpddr3_val/plugin.S
new file mode 100644
index 0000000000..ff629c865a
--- /dev/null
+++ b/board/freescale/mx7d_12x12_lpddr3_val/plugin.S
@@ -0,0 +1,657 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+/* DDR script */
+.macro imx7d_ddrphy_latency_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne TUNE_END
+
+	/*TO 1.1*/
+	ldr r1, =0x1c1c1c1c
+	str r1, [r0, #0x7c]
+	ldr r1, =0x1c1c1c1c
+	str r1, [r0, #0x80]
+	ldr r1, =0x30301c1c
+	str r1, [r0, #0x84]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x88]
+	ldr r1, =0x30303030
+	str r1, [r0, #0x6c]
+
+TUNE_END:
+.endm
+
+.macro imx7d_12x12_lpddr3_val_setting
+
+	/* check whether it is a LPSR resume */
+	ldr	r1, =0x30270000
+	ldr	r7, [r1]
+	cmp	r7, #0
+	beq	16f
+
+	/* disable wdog powerdown counter */
+	ldr	r0, =0x30280000
+	ldrh	r1, =0x0
+	strh	r1, [r0, #0x8]
+
+	/* initialize AIPs 1-3 port */
+	ldr	r0, =0x301f0000
+	ldr	r1, =0x77777777
+	str	r1, [r0]
+	str	r1, [r0, #0x4]
+	ldr	r1, =0x0
+	str	r1, [r0, #0x40]
+	str	r1, [r0, #0x44]
+	str	r1, [r0, #0x48]
+	str	r1, [r0, #0x4c]
+	str	r1, [r0, #0x50]
+
+	ldr	r0, =0x305f0000
+	ldr	r1, =0x77777777
+	str	r1, [r0]
+	str	r1, [r0, #0x4]
+	ldr	r1, =0x0
+	str	r1, [r0, #0x40]
+	str	r1, [r0, #0x44]
+	str	r1, [r0, #0x48]
+	str	r1, [r0, #0x4c]
+	str	r1, [r0, #0x50]
+
+	ldr	r0, =0x309f0000
+	ldr	r1, =0x77777777
+	str	r1, [r0]
+	str	r1, [r0, #0x4]
+	ldr	r1, =0x0
+	str	r1, [r0, #0x40]
+	str	r1, [r0, #0x44]
+	str	r1, [r0, #0x48]
+	str	r1, [r0, #0x4c]
+	str	r1, [r0, #0x50]
+
+	ldr	r1, =0x30360000
+	ldr	r2, =0x30390000
+	ldr	r3, =0x307a0000
+	ldr	r4, =0x30790000
+	ldr	r10, =0x30380000
+	ldr	r11, =0x30340000
+
+	/* turn on ddr power */
+	ldr	r7, =(0x1 << 29)
+	str	r7, [r1, #0x388]
+
+	ldr	r6, =50
+1:
+	subs	r6, r6, #0x1
+	bne	1b
+
+	/* clear ddr_phy reset */
+	ldr	r6, =0x1000
+	ldr	r7, [r2, r6]
+	orr	r7, r7, #0x3
+	str	r7, [r2, r6]
+	ldr	r7, [r2, r6]
+	bic	r7, r7, #0x1
+	str	r7, [r2, r6]
+
+	/* restore DDRC */
+	ldr	r6, =0x0
+	ldr	r7, =0x03040008
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x1a0
+	ldr	r7, =0x80400003
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x1a4
+	ldr	r7, =0x00100020
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x1a8
+	ldr	r7, =0x80100004
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x64
+	ldr	r7, =0x00200038
+	str	r7, [r3, r6]
+
+	ldr	r6, =0xd0
+	ldr	r7, =0xc0350001
+	str	r7, [r3, r6]
+
+	ldr	r6, =0xdc
+	ldr	r7, =0x00C3000A
+	str	r7, [r3, r6]
+
+	ldr	r6, =0xe0
+	ldr	r7, =0x00010000
+	str	r7, [r3, r6]
+
+	ldr	r6, =0xe4
+	ldr	r7, =0x00110006
+	str	r7, [r3, r6]
+
+	ldr	r6, =0xf4
+	ldr	r7, =0x0000033F
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x100
+	ldr	r7, =0x0A0E110B
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x104
+	ldr	r7, =0x00020211
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x108
+	ldr	r7, =0x03060708
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x10c
+	ldr	r7, =0x00A0500C
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x110
+	ldr	r7, =0x05020307
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x114
+	ldr	r7, =0x02020404
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x118
+	ldr	r7, =0x02020003
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x11c
+	ldr	r7, =0x00000202
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x120
+	ldr	r7, =0x00000202
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x180
+	ldr	r7, =0x00600018
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x184
+	ldr	r7, =0x00e00100
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x190
+	ldr	r7, =0x02098205
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x194
+	ldr	r7, =0x00060303
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x200
+	ldr	r7, =0x00000016
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x204
+	ldr	r7, =0x00090909
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x210
+	ldr	r7, =0xF00
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x214
+	ldr	r7, =0x08080808
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x218
+	ldr	r7, =0x0f0f0808
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x240
+	ldr	r7, =0x06000600
+	str	r7, [r3, r6]
+
+	ldr	r6, =0x244
+	ldr	r7, =0x00000000
+	str	r7, [r3, r6]
+
+	ldr	r7, =0x20
+	str	r7, [r3, #0x30]
+	ldr	r7, =0x0
+	str	r7, [r3, #0x1b0]
+
+	/* do PHY, clear ddr_phy reset */
+	ldr	r6, =0x1000
+	ldr	r7, [r2, r6]
+	bic	r7, r7, #0x2
+	str	r7, [r2, r6]
+
+	ldr	r7, [r1, #0x800]
+	and	r7, r7, #0xFF
+	cmp	r7, #0x11
+	bne	2f
+
+	/* for TO1.1 */
+	ldr	r7, [r11]
+	bic	r7, r7, #(1 << 27)
+	str	r7, [r11]
+	ldr	r7, [r11]
+	bic	r7, r7, #(1 << 29)
+	str	r7, [r11]
+2:
+	/* clear/set bit30 of SNVS_MISC_CTRL to ensure exit from ddr retention */
+	ldr	r7, =(0x1 << 30)
+	str	r7, [r1, #0x388]
+	ldr	r7, =(0x1 << 30)
+	str	r7, [r1, #0x384]
+
+	/* need to delay ~5mS */
+	ldr	r6, =0x100000
+3:
+	subs	r6, r6, #0x1
+	bne	3b
+
+	/* restore DDR PHY */
+	ldr	r6, =0x0
+	ldr	r7, =0x17421E40
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x4
+	ldr	r7, =0x10210100
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x8
+	ldr	r7, =0x00010000
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x10
+	ldr	r7, =0x0007080C
+	str	r7, [r4, r6]
+
+	ldr	r6, =0xb0
+	ldr	r7, =0x1010007e
+	str	r7, [r4, r6]
+
+	ldr     r7, [r1, #0x800]
+	and     r7, r7, #0xFF
+	cmp     r7, #0x11
+	bne     4f
+
+	ldr	r6, =0x7c
+	ldr	r7, =0x1c1c1c1c
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x80
+	ldr	r7, =0x1c1c1c1c
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x84
+	ldr	r7, =0x30301c1c
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x88
+	ldr	r7, =0x00000030
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x6c
+	ldr	r7, =0x30303030
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x1c
+	ldr	r7, =0x01010000
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x9c
+	ldr	r7, =0x0DB60D6E
+	str	r7, [r4, r6]
+
+	b	5f
+
+4:
+	ldr	r6, =0x1c
+	ldr	r7, =0x01010000
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x9c
+	ldr	r7, =0x00000b24
+	str	r7, [r4, r6]
+
+5:
+	ldr	r6, =0x20
+	ldr	r7, =0x0a0a0a0a
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x30
+	ldr	r7, =0x06060606
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x50
+	ldr	r7, =0x01000008
+	str	r7, [r4, r6]
+
+	ldr	r6, =0x50
+	ldr	r7, =0x00000008
+	str	r7, [r4, r6]
+
+	ldr	r6, =0xc0
+	ldr	r7, =0x0e487304
+	str	r7, [r4, r6]
+
+	ldr	r6, =0xc0
+	ldr	r7, =0x0e4c7304
+	str	r7, [r4, r6]
+
+	ldr	r6, =0xc0
+	ldr	r7, =0x0e4c7306
+	str	r7, [r4, r6]
+
+6:
+	ldr	r7, [r4, #0xc4]
+	tst	r7, #0x1
+	beq	6b
+
+	ldr	r6, =0xc0
+	ldr	r7, =0x0e487304
+	str	r7, [r4, r6]
+
+	ldr	r7, =0x0
+	add	r9, r10, #0x4000
+	str	r7, [r9, #0x130]
+
+	ldr	r7, =0x170
+	orr	r7, r7, #0x8
+	str	r7, [r11, #0x20]
+
+	ldr	r7, =0x2
+	add	r9, r10, #0x4000
+	str	r7, [r9, #0x130]
+
+	ldr	r7, =0xf
+	str	r7, [r4, #0x18]
+
+	/* wait until self-refresh mode entered */
+11:
+	ldr	r7, [r3, #0x4]
+	and	r7, r7, #0x3
+	cmp	r7, #0x3
+	bne	11b
+	ldr	r7, =0x0
+	str	r7, [r3, #0x320]
+	ldr	r7, =0x1
+	str	r7, [r3, #0x1b0]
+	ldr	r7, =0x1
+	str	r7, [r3, #0x320]
+12:
+	ldr	r7, [r3, #0x324]
+	and	r7, r7, #0x1
+	cmp	r7, #0x1
+	bne	12b
+13:
+	ldr	r7, [r3, #0x4]
+	and	r7, r7, #0x20
+	cmp	r7, #0x20
+	bne	13b
+
+	/* let DDR out of self-refresh */
+	ldr	r7, =0x0
+	str	r7, [r3, #0x30]
+14:
+	ldr	r7, [r3, #0x4]
+	and	r7, r7, #0x30
+	cmp	r7, #0x0
+	bne	14b
+
+15:
+	ldr	r7, [r3, #0x4]
+	and	r7, r7, #0x3
+	cmp	r7, #0x1
+	bne	15b
+
+	imx7_qos_setting
+
+	/* enable port */
+	ldr	r7, =0x1
+	str	r7, [r3, #0x490]
+
+	/* jump to kernel resume */
+	ldr	r1, =0x30270000
+	ldr	r7, [r1]
+
+	mov	pc, r7
+16:
+	/* Configure ocram_epdc */
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0x4f400005
+	str r1, [r0, #0x4]
+
+	/* clear/set bit30 of SNVS_MISC_CTRL to ensure exit from ddr retention */
+	ldr r0, =ANATOP_BASE_ADDR
+	ldr r1, =(0x1 << 30)
+	str r1, [r0, #0x388]
+	str r1, [r0, #0x384]
+
+	ldr r0, =SRC_BASE_ADDR
+	ldr r1, =0x2
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+	ldr r1, =0x03040008
+	str r1, [r0]
+	ldr r1, =0x00200038
+	str r1, [r0, #0x64]
+	ldr r1, =0x1
+	str r1, [r0, #0x490]
+	ldr r1, =0x00350001
+	str r1, [r0, #0xd0]
+	ldr r1, =0x00c3000a
+	str r1, [r0, #0xdc]
+	ldr r1, =0x00010000
+	str r1, [r0, #0xe0]
+	ldr r1, =0x00110006
+	str r1, [r0, #0xe4]
+	ldr r1, =0x33f
+	str r1, [r0, #0xf4]
+	ldr r1, =0x0a0e110b
+	str r1, [r0, #0x100]
+	ldr r1, =0x00020211
+	str r1, [r0, #0x104]
+	ldr r1, =0x03060708
+	str r1, [r0, #0x108]
+	ldr r1, =0x00a0500c
+	str r1, [r0, #0x10c]
+	ldr r1, =0x05020307
+	str r1, [r0, #0x110]
+	ldr r1, =0x02020404
+	str r1, [r0, #0x114]
+	ldr r1, =0x02020003
+	str r1, [r0, #0x118]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x11c]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x120]
+	ldr r1, =0x00600018
+	str r1, [r0, #0x180]
+	ldr r1, =0x00e00100
+	str r1, [r0, #0x184]
+	ldr r1, =0x02098205
+	str r1, [r0, #0x190]
+	ldr r1, =0x00060303
+	str r1, [r0, #0x194]
+	ldr r1, =0x80400003
+	str r1, [r0, #0x1a0]
+	ldr r1, =0x00100020
+	str r1, [r0, #0x1a4]
+	ldr r1, =0x80100004
+	str r1, [r0, #0x1a8]
+
+	ldr r1, =0x00000016
+	str r1, [r0, #0x200]
+	ldr r1, =0x00090909
+	str r1, [r0, #0x204]
+	ldr r1, =0x00000f00
+	str r1, [r0, #0x210]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x214]
+	ldr r1, =0x0f0f0808
+	str r1, [r0, #0x218]
+
+	ldr r1, =0x06000600
+	str r1, [r0, #0x240]
+	mov r1, #0x0
+	str r1, [r0, #0x244]
+
+	ldr r0, =SRC_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x17421e40
+	str r1, [r0]
+	ldr r1, =0x10210100
+	str r1, [r0, #0x4]
+	ldr r1, =0x00010000
+	str r1, [r0, #0x8]
+	ldr r1, =0x0007080c
+	str r1, [r0, #0x10]
+	imx7d_ddrphy_latency_setting
+	ldr r1, =0x1010007e
+	str r1, [r0, #0xb0]
+	ldr r1, =0x01010000
+	str r1, [r0, #0x1c]
+
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne	17f
+
+	ldr r1, =0x0db60d6e
+	str r1, [r0, #0x9c]
+	b	18f
+17:
+	ldr r1, =0x00000b24
+	str r1, [r0, #0x9c]
+18:
+	ldr r1, =0x06060606
+	str r1, [r0, #0x30]
+	ldr r1, =0x0a0a0a0a
+	str r1, [r0, #0x20]
+	ldr r1, =0x01000008
+	str r1, [r0, #0x50]
+	ldr r1, =0x00000008
+	str r1, [r0, #0x50]
+
+	ldr r1, =0x0000000f
+	str r1, [r0, #0x18]
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7306
+	str r1, [r0, #0xc0]
+
+wait_zq:
+	ldr r1, [r0, #0xc4]
+	tst r1, #0x1
+	beq wait_zq
+
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	mov r1, #0x178
+	str r1, [r0, #0x20]
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x2
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+wait_stat:
+	ldr r1, [r0, #0x4]
+	tst r1, #0x1
+	beq wait_stat
+.endm
+
+.macro imx7_clock_gating
+#ifdef CONFIG_IMX_OPTEE
+	ldr r0, =0x30340024
+	ldr r1, =0x1
+	str r1, [r0]
+#endif
+.endm
+
+.macro imx7_qos_setting
+	ldr r0, =REGS_QOS_BASE
+	ldr r1, =0
+	str r1, [r0, #0]
+
+	ldr r1, =0
+	str r1, [r0, #0x60]
+
+	ldr r0, =REGS_QOS_EPDC
+	ldr r1, =0
+	str r1, [r0, #0]
+
+	ldr r0, =REGS_QOS_PXP0
+	ldr r1, =0
+	str r1, [r0, #0]
+
+	ldr r0, =REGS_QOS_PXP1
+	ldr r1, =0
+	str r1, [r0, #0]
+
+	ldr r0, =REGS_QOS_EPDC
+	ldr r1, =0x0f020f22
+	str r1, [r0, #0xd0]
+	str r1, [r0, #0xe0]
+
+	ldr r0, =REGS_QOS_PXP0
+	ldr r1, =0x1
+	str r1, [r0, #0]
+	ldr r0, =REGS_QOS_PXP1
+	str r1, [r0, #0]
+
+	ldr r0, =REGS_QOS_PXP0
+	ldr r1, =0x0f020222
+	str r1, [r0, #0x50]
+	ldr r0, =REGS_QOS_PXP1
+	str r1, [r0, #0x50]
+
+	ldr r0, =REGS_QOS_PXP0
+	ldr r1, =0x0f020222
+	str r1, [r0, #0x60]
+	ldr r0, =REGS_QOS_PXP1
+	str r1, [r0, #0x60]
+
+	ldr r0, =REGS_QOS_PXP0
+	ldr r1, =0x0f020422
+	str r1, [r0, #0x70]
+	ldr r0, =REGS_QOS_PXP1
+	str r1, [r0, #0x70]
+
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0xe080
+	str r1, [r0, #0x34]
+.endm
+
+.macro imx7_ddr_setting
+	imx7d_12x12_lpddr3_val_setting
+.endm
+
+/* include the common plugin code here */
+#include <asm/arch/mx7_plugin.S>
diff --git a/board/freescale/mx7d_19x19_ddr3_val/Kconfig b/board/freescale/mx7d_19x19_ddr3_val/Kconfig
new file mode 100644
index 0000000000..52c8c49001
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_MX7D_19X19_DDR3_VAL
+
+config SYS_BOARD
+	default "mx7d_19x19_ddr3_val"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "mx7d_19x19_ddr3_val"
+
+config SYS_TEXT_BASE
+	default 0x87800000
+endif
diff --git a/board/freescale/mx7d_19x19_ddr3_val/Makefile b/board/freescale/mx7d_19x19_ddr3_val/Makefile
new file mode 100644
index 0000000000..5e48257e15
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx7d_19x19_ddr3_val.o
diff --git a/board/freescale/mx7d_19x19_ddr3_val/imximage.cfg b/board/freescale/mx7d_19x19_ddr3_val/imximage.cfg
new file mode 100644
index 0000000000..81a974901b
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/imximage.cfg
@@ -0,0 +1,105 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_ddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000b24
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+
+#endif
diff --git a/board/freescale/mx7d_19x19_ddr3_val/imximage_TO_1_1.cfg b/board/freescale/mx7d_19x19_ddr3_val/imximage_TO_1_1.cfg
new file mode 100644
index 0000000000..85d04e7404
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/imximage_TO_1_1.cfg
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_ddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30360070 0x00703021
+DATA 4 0x30360090 0x0
+DATA 4 0x30360070 0x00603021
+CHECK_BITS_SET 4 0x30360070 0x80000000
+DATA 4 0x30389880 0x1
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000dee
+DATA 4 0x3079007c 0x18181818
+DATA 4 0x30790080 0x18181818
+DATA 4 0x30790084 0x40401818
+DATA 4 0x30790088 0x00000040
+DATA 4 0x3079006c 0x40404040
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+
+#endif
diff --git a/board/freescale/mx7d_19x19_ddr3_val/mx7d_19x19_ddr3_val.c b/board/freescale/mx7d_19x19_ddr3_val/mx7d_19x19_ddr3_val.c
new file mode 100644
index 0000000000..4ccb37df24
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/mx7d_19x19_ddr3_val.c
@@ -0,0 +1,609 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#ifdef CONFIG_SYS_I2C_MXC
+#include <i2c.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#endif
+#include <asm/arch/crm_regs.h>
+#include <asm/mach-imx/video.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
+	PAD_CTL_DSE_3P3V_49OHM)
+
+#define QSPI_PAD_CTRL	\
+		(PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define SPI_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#ifdef CONFIG_SYS_I2C
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SCL__GPIO4_IO8 | PC,
+		.gp = IMX_GPIO_NR(4, 8),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SDA__GPIO4_IO9 | PC,
+		.gp = IMX_GPIO_NR(4, 9),
+	},
+};
+
+/* I2C2 */
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C2_SCL__I2C2_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C2_SCL__GPIO4_IO10 | PC,
+		.gp = IMX_GPIO_NR(4, 10),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C2_SDA__I2C2_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C2_SDA__GPIO4_IO11 | PC,
+		.gp = IMX_GPIO_NR(4, 11),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc1_emmc_pads[] = {
+	MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_ECSPI2_SCLK__SD1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_ECSPI2_MOSI__SD1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_ECSPI2_MISO__SD1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_ECSPI2_SS0__SD1_DATA7  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD1_CD_B__GPIO5_IO0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_RESET_B__GPIO5_IO2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX7D_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_DATA0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_DATA1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_DATA2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_DATA3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_GPIO1_IO12__SD2_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD2_CD_B__GPIO5_IO9 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD2_RESET_B__GPIO5_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_GPIO1_IO13__SD3_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_GPIO1_IO14__GPIO1_IO14  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+
+#ifdef CONFIG_VIDEO_MXS
+static iomux_v3_cfg_t const lcd_pads[] = {
+	MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA00__LCD_DATA0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA01__LCD_DATA1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA02__LCD_DATA2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA03__LCD_DATA3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA04__LCD_DATA4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA05__LCD_DATA5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA06__LCD_DATA6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA07__LCD_DATA7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA08__LCD_DATA8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA09__LCD_DATA9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA18__LCD_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA19__LCD_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA20__LCD_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA21__LCD_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA22__LCD_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA23__LCD_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+
+	MX7D_PAD_LCD_RESET__GPIO3_IO4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pwm_pads[] = {
+	/* Use GPIO for Brightness adjustment, duty cycle = period */
+	MX7D_PAD_GPIO1_IO01__GPIO1_IO1 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void do_enable_parallel_lcd(struct display_info_t const *dev)
+{
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	imx_iomux_v3_setup_multiple_pads(pwm_pads, ARRAY_SIZE(pwm_pads));
+
+	/* Power up the LCD */
+	gpio_request(IMX_GPIO_NR(3, 4), "lcd_pwr");
+	gpio_direction_output(IMX_GPIO_NR(3, 4) , 1);
+
+	/* Set Brightness to high */
+	gpio_request(IMX_GPIO_NR(1, 1), "lcd_backlight");
+	gpio_direction_output(IMX_GPIO_NR(1, 1) , 1);
+}
+
+struct display_info_t const displays[] = {{
+	.bus = ELCDIF1_IPS_BASE_ADDR,
+	.addr = 0,
+	.pixfmt = 24,
+	.detect = NULL,
+	.enable	= do_enable_parallel_lcd,
+	.mode	= {
+		.name			= "MCIMX28LCD",
+		.xres           = 800,
+		.yres           = 480,
+		.pixclock       = 29850,
+		.left_margin    = 89,
+		.right_margin   = 164,
+		.upper_margin   = 23,
+		.lower_margin   = 10,
+		.hsync_len      = 10,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+#endif
+
+static iomux_v3_cfg_t const per_rst_pads[] = {
+	MX7D_PAD_GPIO1_IO03__GPIO1_IO3 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX7D_PAD_GPIO1_IO11__ENET1_MDC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_GPIO1_IO10__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1  | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2  | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec2(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_QSPI
+#ifndef CONFIG_DM_SPI
+
+static iomux_v3_cfg_t const quadspi_pads[] = {
+	MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA04__QSPI_A_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+	MX7D_PAD_EPDC_DATA08__QSPI_B_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA09__QSPI_B_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA10__QSPI_B_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA11__QSPI_B_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA12__QSPI_B_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA13__QSPI_B_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA14__QSPI_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA15__QSPI_B_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+};
+#endif
+
+int board_qspi_init(void)
+{
+#ifndef CONFIG_DM_SPI
+	/* Set the iomux */
+	imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads));
+#endif
+
+	/* Set the clock */
+	set_clk_qspi();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(5, 9)
+#define USDHC3_CD_GPIO	IMX_GPIO_NR(1, 14)
+
+#define USDHC1_PWR_GPIO	IMX_GPIO_NR(5, 2)
+#define USDHC2_PWR_GPIO	IMX_GPIO_NR(5, 11)
+#define USDHC3_PWR_GPIO	IMX_GPIO_NR(6, 11)
+
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC1_BASE_ADDR},
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = 1; /* Assume uSDHC1 emmc is always present */
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC3_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+int board_mmc_init(bd_t *bis)
+{
+	int i;
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC1 (eMMC)
+	 * mmc1                    USDHC2
+	 * mmc2                    USDHC3
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_emmc_pads, ARRAY_SIZE(usdhc1_emmc_pads));
+			gpio_request(USDHC1_PWR_GPIO, "usdhc1_pwr");
+			gpio_direction_output(USDHC1_PWR_GPIO, 1);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_request(USDHC2_PWR_GPIO, "usdhc2_pwr");
+			gpio_request(USDHC2_CD_GPIO, "usdhc2_cd");
+			gpio_direction_input(USDHC2_CD_GPIO);
+			gpio_direction_output(USDHC2_PWR_GPIO, 1);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			gpio_request(USDHC3_PWR_GPIO, "usdhc3_pwr");
+			gpio_request(USDHC3_CD_GPIO, "usdhc3_cd");
+			gpio_direction_input(USDHC3_CD_GPIO);
+			gpio_direction_output(USDHC3_PWR_GPIO, 1);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+			}
+
+			if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
+				printf("Warning: failed to initialize mmc dev %d\n", i);
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec2();
+
+	ret = fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC1 MXC: %s:failed\n", __func__);
+
+	return 0;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+	int ret;
+
+	/* Use 125M anatop REF_CLK for ENET2, clear gpr1[14], gpr1[18]*/
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+		(IOMUXC_GPR_GPR1_GPR_ENET2_TX_CLK_SEL_MASK |
+		 IOMUXC_GPR_GPR1_GPR_ENET2_CLK_DIR_MASK), 0);
+
+	ret = set_clk_enet(ENET_125MHZ);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* Enable 1.8V(SEL_1P5_1P8_POS_REG) on
+	   Phy control debug reg 0 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	/* rgmii tx clock delay enable */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+
+	/* CS0 */
+	MX7D_PAD_ECSPI1_SS0__GPIO4_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void setup_spinor(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+					 ARRAY_SIZE(ecspi1_pads));
+	gpio_request(IMX_GPIO_NR(4, 19), "ecspi1_cs");
+	gpio_direction_output(IMX_GPIO_NR(4, 19), 0);
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 19)) : -1;
+}
+#endif
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX7
+#ifndef CONFIG_DM_USB
+iomux_v3_cfg_t const usb_otg1_pads[] = {
+	MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const usb_otg2_pads[] = {
+	MX7D_PAD_GPIO1_IO07__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg1_pads, ARRAY_SIZE(usb_otg1_pads));
+	imx_iomux_v3_setup_multiple_pads(usb_otg2_pads, ARRAY_SIZE(usb_otg2_pads));
+}
+#endif
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX7
+#ifndef CONFIG_DM_USB
+	setup_usb();
+#endif
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	/* Reset peripherals */
+	imx_iomux_v3_setup_multiple_pads(per_rst_pads, ARRAY_SIZE(per_rst_pads));
+
+	gpio_request(IMX_GPIO_NR(1, 3), "per_rst");
+	gpio_direction_output(IMX_GPIO_NR(1, 3), 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 3), 1);
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+	setup_spinor();
+#endif
+#endif
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+	board_qspi_init();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x10, 0x22, 0x00, 0x00)},
+	{"sd2", MAKE_CFGVAL(0x10, 0x16, 0x00, 0x00)},
+	{"sd3", MAKE_CFGVAL(0x10, 0x1a, 0x00, 0x00)},
+	{"qspi", MAKE_CFGVAL(0x00, 0x40, 0x00, 0x00)},
+	{NULL,   0},
+};
+#endif
+
+#ifdef CONFIG_DM_PMIC
+int power_init_board(void)
+{
+	struct udevice *dev;
+	int ret, dev_id, rev_id, reg;
+
+	ret = pmic_get("pfuze3000@8", &dev);
+	if (ret == -ENODEV)
+		return 0;
+	if (ret != 0)
+		return ret;
+
+	dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+	rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	reg = pmic_reg_read(dev, PFUZE3000_LDOGCTL);
+	reg |= 0x1;
+	pmic_reg_write(dev, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(dev, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 0.975V */
+	reg = 0xb;
+	pmic_reg_write(dev, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BSTBY, reg);
+
+	/* set SW1B normal voltage to 0.975V */
+	reg = pmic_reg_read(dev, PFUZE3000_SW1BVOLT);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(9750);
+	pmic_reg_write(dev, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+	puts("Board: MX7D 19x19 DDR3 VAL\n");
+
+	return 0;
+}
diff --git a/board/freescale/mx7d_19x19_ddr3_val/plugin.S b/board/freescale/mx7d_19x19_ddr3_val/plugin.S
new file mode 100644
index 0000000000..26914e41eb
--- /dev/null
+++ b/board/freescale/mx7d_19x19_ddr3_val/plugin.S
@@ -0,0 +1,227 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+/* DDR script */
+.macro imx7d_ddrphy_latency_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne NO_DELAY
+
+	/*TO 1.1*/
+	ldr r1, =0x00000dee
+	str r1, [r0, #0x9c]
+	ldr r1, =0x18181818
+	str r1, [r0, #0x7c]
+	ldr r1, =0x18181818
+	str r1, [r0, #0x80]
+	ldr r1, =0x40401818
+	str r1, [r0, #0x84]
+	ldr r1, =0x00000040
+	str r1, [r0, #0x88]
+	ldr r1, =0x40404040
+	str r1, [r0, #0x6c]
+	b TUNE_END
+
+NO_DELAY:
+	/*TO 1.0*/
+	ldr r1, =0x00000b24
+	str r1, [r0, #0x9c]
+
+TUNE_END:
+.endm
+
+.macro imx7d_ddr_freq_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne FREQ_DEFAULT_533
+
+	/* Change to 400Mhz for TO1.1 */
+	ldr r0, =ANATOP_BASE_ADDR
+	ldr r1, =0x70
+	ldr r2, =0x00703021
+	str r2, [r0, r1]
+	ldr r1, =0x90
+	ldr r2, =0x0
+	str r2, [r0, r1]
+	ldr r1, =0x70
+	ldr r2, =0x00603021
+	str r2, [r0, r1]
+
+	ldr r3, =0x80000000
+wait_lock:
+	ldr r2, [r0, r1]
+	and r2, r3
+	cmp r2, r3
+	bne wait_lock
+
+	ldr r0, =CCM_BASE_ADDR
+	ldr r1, =0x9880
+	ldr r2, =0x1
+	str r2, [r0, r1]
+
+FREQ_DEFAULT_533:
+.endm
+
+.macro imx7d_19x19_ddr3_val_ddr_setting
+	imx7d_ddr_freq_setting
+
+	/* Configure ocram_epdc */
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0x4f400005
+	str r1, [r0, #0x4]
+
+	/* clear/set bit30 of SNVS_MISC_CTRL to ensure exit from ddr retention */
+	ldr r0, =ANATOP_BASE_ADDR
+	ldr r1, =(0x1 << 30)
+	str r1, [r0, #0x388]
+	str r1, [r0, #0x384]
+
+	ldr r0, =SRC_BASE_ADDR
+	ldr r1, =0x2
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+	ldr r1, =0x01040001
+	str r1, [r0]
+	ldr r1, =0x80400003
+	str r1, [r0, #0x1a0]
+	ldr r1, =0x00100020
+	str r1, [r0, #0x1a4]
+	ldr r1, =0x80100004
+	str r1, [r0, #0x1a8]
+	ldr r1, =0x00400046
+	str r1, [r0, #0x64]
+	ldr r1, =0x1
+	str r1, [r0, #0x490]
+	ldr r1, =0x00020001
+	str r1, [r0, #0xd0]
+	ldr r1, =0x00690000
+	str r1, [r0, #0xd4]
+	ldr r1, =0x09300004
+	str r1, [r0, #0xdc]
+	ldr r1, =0x04080000
+	str r1, [r0, #0xe0]
+	ldr r1, =0x00100004
+	str r1, [r0, #0xe4]
+	ldr r1, =0x33f
+	str r1, [r0, #0xf4]
+	ldr r1, =0x09081109
+	str r1, [r0, #0x100]
+	ldr r1, =0x0007020d
+	str r1, [r0, #0x104]
+	ldr r1, =0x03040407
+	str r1, [r0, #0x108]
+	ldr r1, =0x00002006
+	str r1, [r0, #0x10c]
+	ldr r1, =0x04020205
+	str r1, [r0, #0x110]
+	ldr r1, =0x03030202
+	str r1, [r0, #0x114]
+	ldr r1, =0x00000803
+	str r1, [r0, #0x120]
+	ldr r1, =0x00800020
+	str r1, [r0, #0x180]
+	ldr r1, =0x02000100
+	str r1, [r0, #0x184]
+	ldr r1, =0x02098204
+	str r1, [r0, #0x190]
+	ldr r1, =0x00030303
+	str r1, [r0, #0x194]
+
+	ldr r1, =0x00000016
+	str r1, [r0, #0x200]
+	ldr r1, =0x00080808
+	str r1, [r0, #0x204]
+	ldr r1, =0x00000f0f
+	str r1, [r0, #0x210]
+	ldr r1, =0x07070707
+	str r1, [r0, #0x214]
+	ldr r1, =0x0f070707
+	str r1, [r0, #0x218]
+
+	ldr r1, =0x06000604
+	str r1, [r0, #0x240]
+	ldr r1, =0x00000001
+	str r1, [r0, #0x244]
+
+	ldr r0, =SRC_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x17420f40
+	str r1, [r0]
+	ldr r1, =0x10210100
+	str r1, [r0, #0x4]
+	ldr r1, =0x00060807
+	str r1, [r0, #0x10]
+	ldr r1, =0x1010007e
+	str r1, [r0, #0xb0]
+	imx7d_ddrphy_latency_setting
+	ldr r1, =0x08080808
+	str r1, [r0, #0x20]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x30]
+	ldr r1, =0x01000010
+	str r1, [r0, #0x50]
+
+	ldr r1, =0x0e407304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e447304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e447306
+	str r1, [r0, #0xc0]
+
+wait_zq:
+	ldr r1, [r0, #0xc4]
+	tst r1, #0x1
+	beq wait_zq
+
+	ldr r1, =0x0e407304
+	str r1, [r0, #0xc0]
+
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	mov r1, #0x178
+	str r1, [r0, #0x20]
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x2
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x0000000f
+	str r1, [r0, #0x18]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+wait_stat:
+	ldr r1, [r0, #0x4]
+	tst r1, #0x1
+	beq wait_stat
+.endm
+
+.macro imx7_clock_gating
+.endm
+
+.macro imx7_qos_setting
+.endm
+
+.macro imx7_ddr_setting
+	imx7d_19x19_ddr3_val_ddr_setting
+.endm
+
+/* include the common plugin code here */
+#include <asm/arch/mx7_plugin.S>
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/Kconfig b/board/freescale/mx7d_19x19_lpddr3_val/Kconfig
new file mode 100644
index 0000000000..a5db2d220d
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/Kconfig
@@ -0,0 +1,20 @@
+if TARGET_MX7D_19X19_LPDDR3_VAL || TARGET_MX7D_19X19_LPDDR2_VAL
+
+config SYS_BOARD
+	default "mx7d_19x19_lpddr3_val"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "mx7d_19x19_lpddr3_val"
+
+config SYS_TEXT_BASE
+	default 0x87800000
+
+config NOR
+	bool "Support for NOR flash"
+	help
+	  The i.MX SoC supports having a NOR flash connected to the WEIM.
+	  Need to set this for NOR_BOOT.
+endif
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/Makefile b/board/freescale/mx7d_19x19_lpddr3_val/Makefile
new file mode 100644
index 0000000000..48148c1771
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2015 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx7d_19x19_lpddr3_val.o
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg b/board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg
new file mode 100644
index 0000000000..b014f11802
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040008
+DATA 4 0x307a0064 0x00200038
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00dc 0x00c3000a
+DATA 4 0x307a00e0 0x00010000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0a0e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x03060708
+DATA 4 0x307a010c 0x00a0500c
+DATA 4 0x307a0110 0x05020307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098205
+DATA 4 0x307a0194 0x00060303
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00090909
+DATA 4 0x307a0210 0x00000f00
+DATA 4 0x307a0214 0x08080808
+DATA 4 0x307a0218 0x0f0f0808
+
+DATA 4 0x307a0240 0x06000600
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421e40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x0007080c
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009c 0x00000b24
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x30790018 0x0000000f
+DATA 4 0x307900c0 0x0e487304
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e4c7306
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/imximage_TO_1_1.cfg b/board/freescale/mx7d_19x19_lpddr3_val/imximage_TO_1_1.cfg
new file mode 100644
index 0000000000..f29b9eac35
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/imximage_TO_1_1.cfg
@@ -0,0 +1,117 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040008
+DATA 4 0x307a0064 0x00200038
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00dc 0x00c3000a
+DATA 4 0x307a00e0 0x00010000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0a0e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x03060708
+DATA 4 0x307a010c 0x00a0500c
+DATA 4 0x307a0110 0x05020307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098205
+DATA 4 0x307a0194 0x00060303
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00090909
+DATA 4 0x307a0210 0x00000f00
+DATA 4 0x307a0214 0x08080808
+DATA 4 0x307a0218 0x0f0f0808
+
+DATA 4 0x307a0240 0x06000601
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421e40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x0007080c
+DATA 4 0x3079007c 0x1c1c1c1c
+DATA 4 0x30790080 0x1c1c1c1c
+DATA 4 0x30790084 0x30301c1c
+DATA 4 0x30790088 0x00000030
+DATA 4 0x3079006c 0x30303030
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009c 0x0db60d6e
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x30790018 0x0000000f
+DATA 4 0x307900c0 0x1e487304
+DATA 4 0x307900c0 0x1e487304
+DATA 4 0x307900c0 0x1e487306
+DATA 4 0x307900c0 0x1e4c7304
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x1e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2.cfg b/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2.cfg
new file mode 100644
index 0000000000..c20fbf792e
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2.cfg
@@ -0,0 +1,119 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+#ifdef CONFIG_SYS_BOOT_QSPI
+BOOT_FROM	qspi
+#elif defined(CONFIG_SYS_BOOT_EIMNOR)
+BOOT_FROM	nor
+#else
+BOOT_FROM	sd
+#endif
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03020004
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00200023
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00d8 0x00001105
+DATA 4 0x307a00dc 0x00c20006
+DATA 4 0x307a00e0 0x00020000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x080e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x02040706
+DATA 4 0x307a010c 0x00504000
+DATA 4 0x307a0110 0x05010307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098203
+DATA 4 0x307a0194 0x00060303
+
+DATA 4 0x307a0200 0x00000015
+DATA 4 0x307a0204 0x00161616
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x04040404
+DATA 4 0x307a0218 0x0f0f0404
+
+DATA 4 0x307a0240 0x06000600
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421640
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x00050408
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009C 0x00000d6e
+DATA 4 0x30790018 0x0000000f
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x307900c0 0x0e487304
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e4c7306
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x000001f8
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2_TO_1_1.cfg b/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2_TO_1_1.cfg
new file mode 100644
index 0000000000..f5888499cf
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2_TO_1_1.cfg
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+#ifdef CONFIG_SYS_BOOT_QSPI
+BOOT_FROM	qspi
+#elif defined(CONFIG_SYS_BOOT_EIMNOR)
+BOOT_FROM	nor
+#else
+BOOT_FROM	sd
+#endif
+
+#ifdef CONFIG_USE_IMXIMG_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx7d_19x19_lpddr3_val/plugin.bin 0x00910000
+#else
+
+#ifdef CONFIG_IMX_HAB
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03020004
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00200023
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00d8 0x00001105
+DATA 4 0x307a00dc 0x00c20006
+DATA 4 0x307a00e0 0x00020000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x080e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x02040706
+DATA 4 0x307a010c 0x00504000
+DATA 4 0x307a0110 0x05010307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098203
+DATA 4 0x307a0194 0x00060303
+
+DATA 4 0x307a0200 0x00000015
+DATA 4 0x307a0204 0x00161616
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x04040404
+DATA 4 0x307a0218 0x0f0f0404
+
+DATA 4 0x307a0240 0x06000600
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421640
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x00050408
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009C 0x00000dee
+DATA 4 0x3079007c 0x08080808
+DATA 4 0x30790080 0x08080808
+DATA 4 0x30790084 0x0a0a0808
+DATA 4 0x30790088 0x0000000a
+DATA 4 0x3079006c 0x0a0a0a0a
+DATA 4 0x30790018 0x0000000f
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x307900c0 0x0e487304
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e4c7306
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x000001f8
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
+#endif
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/mx7d_19x19_lpddr3_val.c b/board/freescale/mx7d_19x19_lpddr3_val/mx7d_19x19_lpddr3_val.c
new file mode 100644
index 0000000000..0bc45f3dae
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/mx7d_19x19_lpddr3_val.c
@@ -0,0 +1,600 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#ifdef CONFIG_SYS_I2C_MXC
+#include <i2c.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#endif
+#include <asm/arch/crm_regs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_98OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
+	PAD_CTL_DSE_3P3V_49OHM)
+
+#define QSPI_PAD_CTRL	\
+		(PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define SPI_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
+
+#define WEIM_NOR_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_PUS_PU100KOHM)
+
+
+#ifdef CONFIG_SYS_I2C
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SCL__GPIO4_IO8 | PC,
+		.gp = IMX_GPIO_NR(4, 8),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SDA__GPIO4_IO9 | PC,
+		.gp = IMX_GPIO_NR(4, 9),
+	},
+};
+
+/* I2C2 */
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C2_SCL__I2C2_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C2_SCL__GPIO4_IO10 | PC,
+		.gp = IMX_GPIO_NR(4, 10),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C2_SDA__I2C2_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C2_SDA__GPIO4_IO11 | PC,
+		.gp = IMX_GPIO_NR(4, 11),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_GPIO1_IO08__SD1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD1_CD_B__GPIO5_IO0    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_RESET_B__GPIO5_IO2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_MTD_NOR_FLASH
+static iomux_v3_cfg_t const eimnor_pads[] = {
+	MX7D_PAD_LCD_DATA00__EIM_DATA0 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA01__EIM_DATA1 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA02__EIM_DATA2 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA03__EIM_DATA3 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA04__EIM_DATA4 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA05__EIM_DATA5 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA06__EIM_DATA6 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA07__EIM_DATA7 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA08__EIM_DATA8 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA09__EIM_DATA9 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA10__EIM_DATA10 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA11__EIM_DATA11 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA12__EIM_DATA12 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA13__EIM_DATA13 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA14__EIM_DATA14 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA15__EIM_DATA15 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+
+	MX7D_PAD_EPDC_DATA00__EIM_AD0   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__EIM_AD1   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__EIM_AD2   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__EIM_AD3   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA04__EIM_AD4   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__EIM_AD5   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__EIM_AD6   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA07__EIM_AD7   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_BDR1__EIM_AD8     | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_PWR_COM__EIM_AD9  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCLK__EIM_AD10   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDLE__EIM_AD11    | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDOE__EIM_AD12    | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDSHR__EIM_AD13   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE0__EIM_AD14   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE1__EIM_AD15   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE2__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE3__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_GDCLK__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_GDOE__EIM_ADDR19  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_GDRL__EIM_ADDR20  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_GDSP__EIM_ADDR21  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_BDR0__EIM_ADDR22  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA20__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA21__EIM_ADDR24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_LCD_DATA22__EIM_ADDR25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+
+	MX7D_PAD_EPDC_DATA08__EIM_OE    | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA09__EIM_RW    | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA10__EIM_CS0_B | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA12__EIM_LBA_B | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA13__EIM_WAIT  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+};
+
+static void eimnor_cs_setup(void)
+{
+	writel(0x00000120, WEIM_IPS_BASE_ADDR + 0x090);
+	writel(0x00210081, WEIM_IPS_BASE_ADDR + 0x000);
+	writel(0x00000001, WEIM_IPS_BASE_ADDR + 0x004);
+	writel(0x0e020000, WEIM_IPS_BASE_ADDR + 0x008);
+	writel(0x00000000, WEIM_IPS_BASE_ADDR + 0x00c);
+	writel(0x0704a040, WEIM_IPS_BASE_ADDR + 0x010);
+}
+
+static void setup_eimnor(void)
+{
+	imx_iomux_v3_setup_multiple_pads(eimnor_pads,
+			ARRAY_SIZE(eimnor_pads));
+
+	eimnor_cs_setup();
+}
+#endif
+
+static iomux_v3_cfg_t const per_rst_pads[] = {
+	MX7D_PAD_GPIO1_IO03__GPIO1_IO3 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_ENET1_COL__WDOG1_WDOG_ANY | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX7D_PAD_GPIO1_IO11__ENET1_MDC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_GPIO1_IO10__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1  | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2  | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec2(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_QSPI
+#ifndef CONFIG_DM_SPI
+static iomux_v3_cfg_t const quadspi_pads[] = {
+	MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA04__QSPI_A_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+	MX7D_PAD_EPDC_DATA08__QSPI_B_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA09__QSPI_B_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA10__QSPI_B_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA11__QSPI_B_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA12__QSPI_B_DQS   | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA13__QSPI_B_SCLK  | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA14__QSPI_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+	MX7D_PAD_EPDC_DATA15__QSPI_B_SS1_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+};
+#endif
+
+int board_qspi_init(void)
+{
+#ifndef CONFIG_DM_SPI
+	/* Set the iomux */
+	imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads));
+#endif
+
+	/* Set the clock */
+	set_clk_qspi();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const gpmi_pads[] = {
+	MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CLK__NAND_CLE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__NAND_ALE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__NAND_RE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__NAND_WE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_MCLK__NAND_WP_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_BCLK__NAND_CE3_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_SYNC__NAND_CE2_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_SYNC__NAND_DQS	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	| MUX_PAD_CTRL(NAND_PAD_READY0_CTRL),
+};
+
+static void setup_gpmi_nand(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	/*
+	 * NAND_USDHC_BUS_CLK is set in rom
+	 */
+
+	set_clk_nand();
+
+	/*
+	 * APBH clock root is set in init_esdhc, USDHC3_CLK.
+	 * There is no clk gate for APBHDMA.
+	 * No touch here.
+	 */
+}
+#endif
+
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(5, 0)
+#define USDHC1_PWR_GPIO	IMX_GPIO_NR(5, 2)
+
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_request(USDHC1_CD_GPIO, "usdhc1_cd");
+			gpio_request(USDHC1_PWR_GPIO, "usdhc1_pwr");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			gpio_direction_output(USDHC1_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC1_PWR_GPIO, 1);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+			}
+
+			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+			if (ret) {
+				printf("Warning: failed to initialize mmc dev %d\n", i);
+				return ret;
+			}
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec2();
+
+	ret = fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC1 MXC: %s:failed\n", __func__);
+
+	return 0;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+	int ret;
+
+	/* Use 125M anatop REF_CLK for ENET2, clear gpr1[14], gpr1[18]*/
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+		(IOMUXC_GPR_GPR1_GPR_ENET2_TX_CLK_SEL_MASK |
+		 IOMUXC_GPR_GPR1_GPR_ENET2_CLK_DIR_MASK), 0);
+
+	ret = set_clk_enet(ENET_125MHZ);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* Enable 1.8V(SEL_1P5_1P8_POS_REG) on
+	   Phy control debug reg 0 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	/* rgmii tx clock delay enable */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX7D_PAD_UART3_RX_DATA__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_UART3_TX_DATA__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX7D_PAD_UART3_RTS_B__ECSPI1_SCLK   | MUX_PAD_CTRL(SPI_PAD_CTRL),
+
+	/* CS0 */
+	MX7D_PAD_UART3_CTS_B__GPIO4_IO7   | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void setup_spinor(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+					 ARRAY_SIZE(ecspi1_pads));
+	gpio_direction_output(IMX_GPIO_NR(4, 7), 0);
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 7)) : -1;
+}
+#endif
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX7
+#ifndef CONFIG_DM_USB
+
+iomux_v3_cfg_t const usb_otg1_pads[] = {
+	MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const usb_otg2_pads[] = {
+	MX7D_PAD_GPIO1_IO07__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg1_pads, ARRAY_SIZE(usb_otg1_pads));
+	imx_iomux_v3_setup_multiple_pads(usb_otg2_pads, ARRAY_SIZE(usb_otg2_pads));
+}
+#endif
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX7
+#ifndef CONFIG_DM_USB
+	setup_usb();
+#endif
+#endif
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	/* Reset peripherals */
+	imx_iomux_v3_setup_multiple_pads(per_rst_pads, ARRAY_SIZE(per_rst_pads));
+
+	gpio_request(IMX_GPIO_NR(1, 3), "per rst");
+	gpio_direction_output(IMX_GPIO_NR(1, 3) , 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 3), 1);
+
+#ifdef CONFIG_MXC_SPI
+#ifndef CONFIG_DM_SPI
+	setup_spinor();
+#endif
+#endif
+
+#ifdef CONFIG_MTD_NOR_FLASH
+	setup_eimnor();
+#endif
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+	board_qspi_init();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd1", MAKE_CFGVAL(0x10, 0x12, 0x00, 0x00)},
+	{"qspi", MAKE_CFGVAL(0x00, 0x40, 0x00, 0x00)},
+	{NULL,   0},
+};
+#endif
+
+#ifdef CONFIG_DM_PMIC
+int power_init_board(void)
+{
+	struct udevice *dev;
+	int ret, dev_id, rev_id, reg;
+
+	ret = pmic_get("pfuze3000@8", &dev);
+	if (ret == -ENODEV)
+		return 0;
+	if (ret != 0)
+		return ret;
+
+	dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+	rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	reg = pmic_reg_read(dev, PFUZE3000_LDOGCTL);
+	reg |= 0x1;
+	pmic_reg_write(dev, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(dev, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 0.975V */
+	reg = 0xb;
+	pmic_reg_write(dev, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(dev, PFUZE3000_SW1BSTBY, reg);
+
+	/* set SW1B normal voltage to 0.975V */
+	reg = pmic_reg_read(dev, PFUZE3000_SW1BVOLT);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(9750);
+	pmic_reg_write(dev, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+#ifdef CONFIG_TARGET_MX7D_19X19_LPDDR2_VAL
+	puts("Board: MX7D 19x19 LPDDR2 VAL\n");
+#else
+	puts("Board: MX7D 19x19 LPDDR3 VAL\n");
+#endif
+	return 0;
+}
diff --git a/board/freescale/mx7d_19x19_lpddr3_val/plugin.S b/board/freescale/mx7d_19x19_lpddr3_val/plugin.S
new file mode 100644
index 0000000000..29d76d5daf
--- /dev/null
+++ b/board/freescale/mx7d_19x19_lpddr3_val/plugin.S
@@ -0,0 +1,378 @@
+/*
+ * Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+/* DDR script */
+.macro imx7d_ddrphy_lpddr3_latency_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne TUNE_END
+
+	/*TO 1.1*/
+	ldr r1, =0x1c1c1c1c
+	str r1, [r0, #0x7c]
+	ldr r1, =0x1c1c1c1c
+	str r1, [r0, #0x80]
+	ldr r1, =0x30301c1c
+	str r1, [r0, #0x84]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x88]
+	ldr r1, =0x30303030
+	str r1, [r0, #0x6c]
+
+TUNE_END:
+.endm
+
+.macro imx7d_ddrphy_lpddr2_latency_setting
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne NO_DELAY
+
+	/*TO 1.1*/
+	ldr r1, =0x00000dee
+	str r1, [r0, #0x9c]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x7c]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x80]
+	ldr r1, =0x0a0a0808
+	str r1, [r0, #0x84]
+	ldr r1, =0x0000000a
+	str r1, [r0, #0x88]
+	ldr r1, =0x0a0a0a0a
+	str r1, [r0, #0x6c]
+	b TUNE_END
+
+NO_DELAY:
+	/*TO 1.0*/
+	ldr r1, =0x00000d6e
+	str r1, [r0, #0x9c]
+
+TUNE_END:
+.endm
+
+.macro imx7d_19x19_lpddr3_val_setting
+	/* Configure ocram_epdc */
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0x4f400005
+	str r1, [r0, #0x4]
+
+	ldr r0, =SRC_BASE_ADDR
+	ldr r1, =0x2
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+	ldr r1, =0x03040008
+	str r1, [r0]
+	ldr r1, =0x00200038
+	str r1, [r0, #0x64]
+	ldr r1, =0x1
+	str r1, [r0, #0x490]
+	ldr r1, =0x00350001
+	str r1, [r0, #0xd0]
+	ldr r1, =0x00c3000a
+	str r1, [r0, #0xdc]
+	ldr r1, =0x00010000
+	str r1, [r0, #0xe0]
+	ldr r1, =0x00110006
+	str r1, [r0, #0xe4]
+	ldr r1, =0x33f
+	str r1, [r0, #0xf4]
+	ldr r1, =0x0a0e110b
+	str r1, [r0, #0x100]
+	ldr r1, =0x00020211
+	str r1, [r0, #0x104]
+	ldr r1, =0x03060708
+	str r1, [r0, #0x108]
+	ldr r1, =0x00a0500c
+	str r1, [r0, #0x10c]
+	ldr r1, =0x05020307
+	str r1, [r0, #0x110]
+	ldr r1, =0x02020404
+	str r1, [r0, #0x114]
+	ldr r1, =0x02020003
+	str r1, [r0, #0x118]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x11c]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x120]
+	ldr r1, =0x00600018
+	str r1, [r0, #0x180]
+	ldr r1, =0x00e00100
+	str r1, [r0, #0x184]
+	ldr r1, =0x02098205
+	str r1, [r0, #0x190]
+	ldr r1, =0x00060303
+	str r1, [r0, #0x194]
+	ldr r1, =0x80400003
+	str r1, [r0, #0x1a0]
+	ldr r1, =0x00100020
+	str r1, [r0, #0x1a4]
+	ldr r1, =0x80100004
+	str r1, [r0, #0x1a8]
+
+	ldr r1, =0x00000016
+	str r1, [r0, #0x200]
+	ldr r1, =0x00090909
+	str r1, [r0, #0x204]
+	ldr r1, =0x00000f00
+	str r1, [r0, #0x210]
+	ldr r1, =0x08080808
+	str r1, [r0, #0x214]
+	ldr r1, =0x0f0f0808
+	str r1, [r0, #0x218]
+
+	ldr r1, =0x06000600
+	str r1, [r0, #0x240]
+	mov r1, #0x0
+	str r1, [r0, #0x244]
+
+	ldr r0, =SRC_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x17421e40
+	str r1, [r0]
+	ldr r1, =0x10210100
+	str r1, [r0, #0x4]
+	ldr r1, =0x00010000
+	str r1, [r0, #0x8]
+	ldr r1, =0x0007080c
+	str r1, [r0, #0x10]
+	imx7d_ddrphy_lpddr3_latency_setting
+	ldr r1, =0x1010007e
+	str r1, [r0, #0xb0]
+	ldr r1, =0x01010000
+	str r1, [r0, #0x1c]
+
+	ldr r2, =ANATOP_BASE_ADDR
+	ldr r3, [r2, #0x800]
+	and r3, r3, #0xFF
+	cmp r3, #0x11
+	bne	1f
+
+	ldr r1, =0x0db60d6e
+	str r1, [r0, #0x9c]
+	b	2f
+1:
+	ldr r1, =0x00000b24
+	str r1, [r0, #0x9c]
+2:
+	ldr r1, =0x06060606
+	str r1, [r0, #0x30]
+	ldr r1, =0x0a0a0a0a
+	str r1, [r0, #0x20]
+	ldr r1, =0x01000008
+	str r1, [r0, #0x50]
+	ldr r1, =0x00000008
+	str r1, [r0, #0x50]
+
+	ldr r1, =0x0000000f
+	str r1, [r0, #0x18]
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7306
+	str r1, [r0, #0xc0]
+
+wait_zq:
+	ldr r1, [r0, #0xc4]
+	tst r1, #0x1
+	beq wait_zq
+
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	mov r1, #0x178
+	str r1, [r0, #0x20]
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x2
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+wait_stat:
+	ldr r1, [r0, #0x4]
+	tst r1, #0x1
+	beq wait_stat
+.endm
+
+.macro imx7d_19x19_lpddr2_val_setting
+	/* Configure ocram_epdc */
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	ldr r1, =0x4f400005
+	str r1, [r0, #0x4]
+
+	ldr r0, =SRC_BASE_ADDR
+	ldr r1, =0x2
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+	ldr r1, =0x03020004
+	str r1, [r0]
+	ldr r1, =0x80400003
+	str r1, [r0, #0x1a0]
+	ldr r1, =0x00100020
+	str r1, [r0, #0x1a4]
+	ldr r1, =0x80100004
+	str r1, [r0, #0x1a8]
+	ldr r1, =0x00200023
+	str r1, [r0, #0x64]
+	ldr r1, =0x1
+	str r1, [r0, #0x490]
+	ldr r1, =0x00350001
+	str r1, [r0, #0xd0]
+	ldr r1, =0x00001105
+	str r1, [r0, #0xd8]
+	ldr r1, =0x00c20006
+	str r1, [r0, #0xdc]
+	ldr r1, =0x00020000
+	str r1, [r0, #0xe0]
+	ldr r1, =0x00110006
+	str r1, [r0, #0xe4]
+	ldr r1, =0x33f
+	str r1, [r0, #0xf4]
+	ldr r1, =0x080e110b
+	str r1, [r0, #0x100]
+	ldr r1, =0x00020211
+	str r1, [r0, #0x104]
+	ldr r1, =0x02040706
+	str r1, [r0, #0x108]
+	ldr r1, =0x00504000
+	str r1, [r0, #0x10c]
+	ldr r1, =0x05010307
+	str r1, [r0, #0x110]
+	ldr r1, =0x02020404
+	str r1, [r0, #0x114]
+	ldr r1, =0x02020003
+	str r1, [r0, #0x118]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x11c]
+	ldr r1, =0x00000202
+	str r1, [r0, #0x120]
+	ldr r1, =0x00600018
+	str r1, [r0, #0x180]
+	ldr r1, =0x00e00100
+	str r1, [r0, #0x184]
+	ldr r1, =0x02098203
+	str r1, [r0, #0x190]
+	ldr r1, =0x00060303
+	str r1, [r0, #0x194]
+
+	ldr r1, =0x00000015
+	str r1, [r0, #0x200]
+	ldr r1, =0x00161616
+	str r1, [r0, #0x204]
+	ldr r1, =0x00000f0f
+	str r1, [r0, #0x210]
+	ldr r1, =0x04040404
+	str r1, [r0, #0x214]
+	ldr r1, =0x0f0f0404
+	str r1, [r0, #0x218]
+
+	ldr r1, =0x06000600
+	str r1, [r0, #0x240]
+	mov r1, #0x0
+	str r1, [r0, #0x244]
+
+	ldr r0, =SRC_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x1000
+	str r1, [r0, r2]
+
+	ldr r0, =DDRPHY_IPS_BASE_ADDR
+	ldr r1, =0x17421640
+	str r1, [r0]
+	ldr r1, =0x10210100
+	str r1, [r0, #0x4]
+	ldr r1, =0x00010000
+	str r1, [r0, #0x8]
+	ldr r1, =0x00050408
+	str r1, [r0, #0x10]
+	ldr r1, =0x1010007e
+	str r1, [r0, #0xb0]
+	ldr r1, =0x01010000
+	str r1, [r0, #0x1c]
+	imx7d_ddrphy_lpddr2_latency_setting
+	ldr r1, =0x0000000f
+	str r1, [r0, #0x18]
+
+	ldr r1, =0x06060606
+	str r1, [r0, #0x30]
+	ldr r1, =0x0a0a0a0a
+	str r1, [r0, #0x20]
+	ldr r1, =0x01000008
+	str r1, [r0, #0x50]
+	ldr r1, =0x00000008
+	str r1, [r0, #0x50]
+
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e4c7306
+	str r1, [r0, #0xc0]
+
+wait_zq:
+	ldr r1, [r0, #0xc4]
+	tst r1, #0x1
+	beq wait_zq
+
+	ldr r1, =0x0e4c7304
+	str r1, [r0, #0xc0]
+	ldr r1, =0x0e487304
+	str r1, [r0, #0xc0]
+
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x0
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+	ldr r0, =IOMUXC_GPR_BASE_ADDR
+	mov r1, #0x1f8
+	str r1, [r0, #0x20]
+	ldr r0, =CCM_BASE_ADDR
+	mov r1, #0x2
+	ldr r2, =0x4130
+	str r1, [r0, r2]
+
+	ldr r0, =DDRC_IPS_BASE_ADDR
+wait_stat:
+	ldr r1, [r0, #0x4]
+	tst r1, #0x1
+	beq wait_stat
+.endm
+
+.macro imx7_clock_gating
+.endm
+
+.macro imx7_qos_setting
+.endm
+
+.macro imx7_ddr_setting
+#if defined (TARGET_MX7D_19X19_LPDDR2_VAL)
+	imx7d_19x19_lpddr2_val_setting
+#else
+	imx7d_19x19_lpddr3_val_setting
+#endif
+.endm
+
+/* include the common plugin code here */
+#include <asm/arch/mx7_plugin.S>
diff --git a/configs/mx7d_12x12_ddr3_val_defconfig b/configs/mx7d_12x12_ddr3_val_defconfig
new file mode 100644
index 0000000000..fe8498a31f
--- /dev/null
+++ b/configs/mx7d_12x12_ddr3_val_defconfig
@@ -0,0 +1,69 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_DDR3_VAL=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-ddr3-val"
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_ddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-ddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
diff --git a/configs/mx7d_12x12_lpddr3_val_defconfig b/configs/mx7d_12x12_lpddr3_val_defconfig
new file mode 100644
index 0000000000..d2a7641c7c
--- /dev/null
+++ b/configs/mx7d_12x12_lpddr3_val_defconfig
@@ -0,0 +1,75 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_LPDDR3_VAL=y
+CONFIG_USE_IMXIMG_PLUGIN=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_DM_ETH=y
diff --git a/configs/mx7d_12x12_lpddr3_val_epdc_defconfig b/configs/mx7d_12x12_lpddr3_val_epdc_defconfig
new file mode 100644
index 0000000000..a7449f7d5c
--- /dev/null
+++ b/configs/mx7d_12x12_lpddr3_val_epdc_defconfig
@@ -0,0 +1,77 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_LPDDR3_VAL=y
+CONFIG_USE_IMXIMG_PLUGIN=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-lpddr3-val.dtb"
+CONFIG_LCD=y
+CONFIG_MXC_EPDC=y
+CONFIG_CMD_BMP=y
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_DM_ETH=y
diff --git a/configs/mx7d_12x12_lpddr3_val_optee_defconfig b/configs/mx7d_12x12_lpddr3_val_optee_defconfig
new file mode 100644
index 0000000000..8bb3d1c3f0
--- /dev/null
+++ b/configs/mx7d_12x12_lpddr3_val_optee_defconfig
@@ -0,0 +1,76 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_LPDDR3_VAL=y
+CONFIG_USE_IMXIMG_PLUGIN=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+CONFIG_IMX_OPTEE=y
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_DM_ETH=y
diff --git a/configs/mx7d_12x12_lpddr3_val_qspi1_defconfig b/configs/mx7d_12x12_lpddr3_val_qspi1_defconfig
new file mode 100644
index 0000000000..c21d2e32e3
--- /dev/null
+++ b/configs/mx7d_12x12_lpddr3_val_qspi1_defconfig
@@ -0,0 +1,91 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_LPDDR3_VAL=y
+CONFIG_USE_IMXIMG_PLUGIN=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_IMX_BOOTAUX=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-lpddr3-val-qspi"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_FSL_QSPI=y
+CONFIG_SF_DEFAULT_BUS=0
+CONFIG_SF_DEFAULT_CS=0
+CONFIG_SF_DEFAULT_SPEED=40000000
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_QSPI_BOOT=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+# CONFIG_ENV_IS_IN_MMC is not set
+CONFIG_DM_ETH=y
diff --git a/configs/mx7d_12x12_lpddr3_val_spinor_defconfig b/configs/mx7d_12x12_lpddr3_val_spinor_defconfig
new file mode 100644
index 0000000000..d262648800
--- /dev/null
+++ b/configs/mx7d_12x12_lpddr3_val_spinor_defconfig
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_12X12_LPDDR3_VAL=y
+CONFIG_USE_IMXIMG_PLUGIN=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-12x12-lpddr3-val-ecspi"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_12x12_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-12x12-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_MXC_SPI=y
+CONFIG_SF_DEFAULT_BUS=0
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_CS=0
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_DM_ETH=y
+CONFIG_SPI_BOOT=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+# CONFIG_ENV_IS_IN_MMC is not set
diff --git a/configs/mx7d_19x19_ddr3_val_defconfig b/configs/mx7d_19x19_ddr3_val_defconfig
new file mode 100644
index 0000000000..71c1f04daa
--- /dev/null
+++ b/configs/mx7d_19x19_ddr3_val_defconfig
@@ -0,0 +1,85 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_MX7D_19X19_DDR3_VAL=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_IMX_BOOTAUX=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-19x19-ddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_19x19_ddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-19x19-ddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_FSL_QSPI=y
+CONFIG_SF_DEFAULT_CS=0
+CONFIG_SF_DEFAULT_SPEED=40000000
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_BUS=0
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
diff --git a/configs/mx7d_19x19_lpddr2_val_defconfig b/configs/mx7d_19x19_lpddr2_val_defconfig
new file mode 100644
index 0000000000..dd6da6d126
--- /dev/null
+++ b/configs/mx7d_19x19_lpddr2_val_defconfig
@@ -0,0 +1,71 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_TARGET_MX7D_19X19_LPDDR2_VAL=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-19x19-lpddr2-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_19x19_lpddr3_val/imximage_lpddr2.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-19x19-lpddr2-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
diff --git a/configs/mx7d_19x19_lpddr3_val_defconfig b/configs/mx7d_19x19_lpddr3_val_defconfig
new file mode 100644
index 0000000000..b298db34fe
--- /dev/null
+++ b/configs/mx7d_19x19_lpddr3_val_defconfig
@@ -0,0 +1,73 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xE0000
+CONFIG_DM_GPIO=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_TARGET_MX7D_19X19_LPDDR3_VAL=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-19x19-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-19x19-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_CMD_FLASH=y
diff --git a/configs/mx7d_19x19_lpddr3_val_eimnor_defconfig b/configs/mx7d_19x19_lpddr3_val_eimnor_defconfig
new file mode 100644
index 0000000000..96bd94ab53
--- /dev/null
+++ b/configs/mx7d_19x19_lpddr3_val_eimnor_defconfig
@@ -0,0 +1,76 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x40000
+CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_ENV_ADDR=0x281C0000
+CONFIG_DM_GPIO=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_TARGET_MX7D_19X19_LPDDR3_VAL=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-19x19-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-19x19-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_NOR=y
+CONFIG_NOR_BOOT=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_ENV_IS_IN_FLASH=y
+# CONFIG_ENV_IS_IN_MMC is not set
+CONFIG_CMD_FLASH=y
diff --git a/configs/mx7d_19x19_lpddr3_val_nand_defconfig b/configs/mx7d_19x19_lpddr3_val_nand_defconfig
new file mode 100644
index 0000000000..e2bd22f2bd
--- /dev/null
+++ b/configs/mx7d_19x19_lpddr3_val_nand_defconfig
@@ -0,0 +1,86 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0x3C00000
+CONFIG_DM_GPIO=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_IMX_RDC=y
+CONFIG_TARGET_MX7D_19X19_LPDDR3_VAL=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="imx7d-19x19-lpddr3-val"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7d_19x19_lpddr3_val/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx7d-19x19-lpddr3-val.dtb"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX7=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_ERRNO_STR=y
+CONFIG_NAND_BOOT=y
+CONFIG_ENV_IS_IN_NAND=y
+# CONFIG_ENV_IS_IN_MMC is not set
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
+CONFIG_MTDPARTS_SKIP_INVALID=y
+CONFIG_NAND=y
+CONFIG_NAND_MXS=y
+CONFIG_NAND_MXS_DT=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_CMD_UBI=y
diff --git a/include/configs/mx7d_12x12_ddr3_val.h b/include/configs/mx7d_12x12_ddr3_val.h
new file mode 100644
index 0000000000..ffb92af988
--- /dev/null
+++ b/include/configs/mx7d_12x12_ddr3_val.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * Configuration settings for the Freescale i.MX7D 12x12 DDR3 ARM2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_12X12_DDR3_VAL_CONFIG_H
+#define __MX7D_12X12_DDR3_VAL_CONFIG_H
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#define CONFIG_SYS_MMC_ENV_DEV		1	/* USDHC3 */
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC3 */
+
+#define PHYS_SDRAM_SIZE			SZ_1G
+
+
+#include "mx7d_val.h"
+
+#endif
diff --git a/include/configs/mx7d_12x12_lpddr3_val.h b/include/configs/mx7d_12x12_lpddr3_val.h
new file mode 100644
index 0000000000..76aee24681
--- /dev/null
+++ b/include/configs/mx7d_12x12_lpddr3_val.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7D 12x12 LPDDR3 ARM2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_12X12_LPDDR3_VAL_CONFIG_H
+#define __MX7D_12X12_LPDDR3_VAL_CONFIG_H
+
+#define CONFIG_SYS_FSL_USDHC_NUM    3
+#define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */
+
+#define PHYS_SDRAM_SIZE			SZ_2G
+
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#ifdef CONFIG_DM_ETH
+#define CONFIG_ETHPRIME                 "eth0"
+#else
+#define CONFIG_ETHPRIME                 "FEC"
+#endif
+#define CONFIG_FEC_MXC_PHYADDR          1
+
+#define CONFIG_PHY_ATHEROS
+
+/* ENET1 */
+#define IMX_FEC_BASE			ENET_IPS_BASE_ADDR
+
+/* #define CONFIG_SPLASH_SCREEN*/
+/* #define CONFIG_MXC_EPDC*/
+
+#include "mx7d_val.h"
+
+#endif
diff --git a/include/configs/mx7d_19x19_ddr3_val.h b/include/configs/mx7d_19x19_ddr3_val.h
new file mode 100644
index 0000000000..8a3a919e2f
--- /dev/null
+++ b/include/configs/mx7d_19x19_ddr3_val.h
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7D 19x19 DDR3 ARM2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_19X19_DDR3_VAL_CONFIG_H
+#define __MX7D_19X19_DDR3_VAL_CONFIG_H
+
+#define CONFIG_SYS_FSL_USDHC_NUM    3
+#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+
+#define PHYS_SDRAM_SIZE			SZ_1G
+
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#ifdef CONFIG_DM_ETH
+#define CONFIG_ETHPRIME                 "eth0"
+#else
+#define CONFIG_ETHPRIME                 "FEC"
+#endif
+#define CONFIG_FEC_MXC_PHYADDR          0
+
+#define CONFIG_PHY_ATHEROS
+
+/* ENET2 */
+#define IMX_FEC_BASE			ENET2_IPS_BASE_ADDR
+
+#define CONFIG_FEC_MXC_MDIO_BASE	ENET_IPS_BASE_ADDR
+
+
+#ifndef CONFIG_DM_I2C
+#define CONFIG_SYS_I2C
+#endif
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#endif
+
+/* PMIC */
+#ifndef CONFIG_DM_PMIC
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+#endif
+
+
+#include "mx7d_val.h"
+
+#endif
diff --git a/include/configs/mx7d_19x19_lpddr3_val.h b/include/configs/mx7d_19x19_lpddr3_val.h
new file mode 100644
index 0000000000..32b9e34a79
--- /dev/null
+++ b/include/configs/mx7d_19x19_lpddr3_val.h
@@ -0,0 +1,65 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7D 19x19 LPDDR3 ARM2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_19X19_LPDDR3_VAL_CONFIG_H
+#define __MX7D_19X19_LPDDR3_VAL_CONFIG_H
+
+#define CONFIG_SYS_FSL_USDHC_NUM	1
+#define CONFIG_SYS_MMC_ENV_DEV		0	/* USDHC1 */
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */
+
+#ifdef CONFIG_TARGET_MX7D_19X19_LPDDR2_VAL
+#define PHYS_SDRAM_SIZE			SZ_512M
+#else
+#define PHYS_SDRAM_SIZE			SZ_2G
+#endif
+
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#ifdef CONFIG_DM_ETH
+#define CONFIG_ETHPRIME                 "eth0"
+#else
+#define CONFIG_ETHPRIME                 "FEC"
+#endif
+#define CONFIG_FEC_MXC_PHYADDR          0
+
+#define CONFIG_PHY_ATHEROS
+
+/* ENET2 */
+#define IMX_FEC_BASE			ENET2_IPS_BASE_ADDR
+
+#define CONFIG_FEC_MXC_MDIO_BASE	ENET_IPS_BASE_ADDR
+
+/* QSPI conflict with EIMNOR */
+/* FEC0 conflict with EIMNOR */
+/* ECSPI conflict with UART */
+#ifdef CONFIG_MTD_NOR_FLASH
+#undef CONFIG_FEC_MXC
+#endif
+
+#ifndef CONFIG_DM_I2C
+#define CONFIG_SYS_I2C
+#endif
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#endif
+
+/* PMIC */
+#ifndef CONFIG_DM_PMIC
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+#endif
+
+
+#include "mx7d_val.h"
+
+#endif
diff --git a/include/configs/mx7d_val.h b/include/configs/mx7d_val.h
new file mode 100644
index 0000000000..07121216e1
--- /dev/null
+++ b/include/configs/mx7d_val.h
@@ -0,0 +1,256 @@
+/*
+ * Copyright (C) 2014-2016 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX7D ARM2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX7D_VAL_CONFIG_H
+#define __MX7D_VAL_CONFIG_H
+
+#include "mx7_common.h"
+#include "imx_env.h"
+
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)
+
+#define CONFIG_MXC_UART_BASE		UART1_IPS_BASE_ADDR
+
+#define CONFIG_IMX_THERMAL
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+
+/* I2C configs */
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED		100000
+
+#define CONFIG_LOADADDR			0x80800000
+
+#define CONFIG_SYS_AUXCORE_BOOTDATA 0x68000000 /* Set to QSPI1 B flash at default */
+#define SF_QSPI1_B_CS_NUM 2
+#define SF_QSPI1_B_BUS_NUM 0
+
+#ifdef CONFIG_IMX_BOOTAUX
+
+#define UPDATE_M4_ENV \
+	"m4image=m4_qspi.bin\0" \
+	"m4_qspi_cs="__stringify(SF_QSPI1_B_CS_NUM)"\0" \
+	"m4_qspi_bus="__stringify(SF_QSPI1_B_BUS_NUM)"\0" \
+	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
+	"update_m4_from_sd=" \
+		"if sf probe ${m4_qspi_bus}:${m4_qspi_cs}; then " \
+			"if run loadm4image; then " \
+				"setexpr fw_sz ${filesize} + 0xffff; " \
+				"setexpr fw_sz ${fw_sz} / 0x10000; "	\
+				"setexpr fw_sz ${fw_sz} * 0x10000; "	\
+				"sf erase 0x0 ${fw_sz}; " \
+				"sf write ${loadaddr} 0x0 ${filesize}; " \
+			"fi; " \
+		"fi\0" \
+	"m4boot=sf probe ${m4_qspi_bus}:${m4_qspi_cs}; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
+#else
+#define UPDATE_M4_ENV ""
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(nandboot),16m(nandkernel),16m(nanddtb),16m(nandtee),-(nandrootfs)"
+#else
+#define MFG_NAND_PARTITION ""
+#endif
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_MFG_ENV_SETTINGS \
+	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
+	"initrd_addr=0x86800000\0" \
+	"initrd_high=0xffffffff\0" \
+	"emmc_dev=2\0"\
+	"sd_dev=0\0" \
+	"mtdparts=" MFG_NAND_PARTITION \
+	"\0"\
+
+#if defined(CONFIG_NAND_BOOT)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_MFG_ENV_SETTINGS \
+	"panel=MCIMX28LCD\0" \
+	"fdt_addr=0x83000000\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"console=ttymxc0\0" \
+	"bootargs=console=ttymxc0,115200 ubi.mtd=nandrootfs "  \
+		"root=ubi0:nandrootfs rootfstype=ubifs "		     \
+		MFG_NAND_PARTITION \
+		"\0" \
+	"bootcmd=nand read ${loadaddr} 0x4000000 0xc00000;"\
+		"nand read ${fdt_addr} 0x5000000 0x100000;"\
+		"bootz ${loadaddr} - ${fdt_addr}\0"
+
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_MFG_ENV_SETTINGS \
+	UPDATE_M4_ENV \
+	"epdc_waveform=epdc_splash.bin\0" \
+	"panel=MCIMX28LCD\0" \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+		"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else run netboot; fi"
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x40000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SYS_FSL_QSPI_AHB
+#define FSL_QSPI_FLASH_NUM		4
+#define FSL_QSPI_FLASH_SIZE		SZ_64M
+#define QSPI0_BASE_ADDR			QSPI1_IPS_BASE_ADDR
+#define QSPI0_AMBA_BASE			QSPI0_ARB_BASE_ADDR
+#endif
+
+#ifdef CONFIG_MTD_NOR_FLASH
+#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
+#define CONFIG_SYS_FLASH_SECT_SIZE	(256 * 1024)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT  512  /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_PROTECTION
+#endif
+
+#ifdef CONFIG_NAND_MXS
+
+/* NAND stuff */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#endif
+
+#if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+#endif
+
+#ifdef CONFIG_VIDEO
+#define	CONFIG_VIDEO_MXS
+#define	CONFIG_VIDEO_LOGO
+#define	CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IMX_VIDEO_SKIP
+#endif
+
+#if defined(CONFIG_MXC_EPDC)
+/*
+ * Framebuffer and LCD
+ */
+#define CONFIG_SPLASH_SCREEN
+
+#undef LCD_TEST_PATTERN
+/* #define CONFIG_SPLASH_IS_IN_MMC			1 */
+#define LCD_BPP					LCD_MONOCHROME
+/* #define CONFIG_SPLASH_SCREEN_ALIGN		1 */
+
+#define CONFIG_WAVEFORM_BUF_SIZE		0x400000
+#endif
+
+/* USB Configs */
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+
+#endif				/* __CONFIG_H */