diff options
author | Peng Fan <peng.fan@nxp.com> | 2018-01-05 14:05:17 +0800 |
---|---|---|
committer | Simon Glass <sjg@chromium.org> | 2018-01-21 10:01:02 -0700 |
commit | 0fe4e418254c071f74d0134a8f4a2f4362b5bf4b (patch) | |
tree | 69496a3c622313ddcf498e4def7d3df3600186df | |
parent | d1ccaa4760ae33fccad69cdbec4713c78d68a02e (diff) |
dm: pinctrl: sync with Linux to use pin_config_param
Sync with Linux commit 30a7acd573899fd8b("Linux 4.15-rc6")
to use enum pin_config_param.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-rw-r--r-- | include/dm/pinctrl.h | 112 |
1 files changed, 66 insertions, 46 deletions
diff --git a/include/dm/pinctrl.h b/include/dm/pinctrl.h index 0eb4b924d4d..c6c8f6158d3 100644 --- a/include/dm/pinctrl.h +++ b/include/dm/pinctrl.h @@ -137,6 +137,12 @@ struct pinctrl_ops { /** * Generic pin configuration paramters * + * enum pin_config_param - possible pin configuration parameters + * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it + * weakly drives the last value on a tristate bus, also known as a "bus + * holder", "bus keeper" or "repeater". This allows another device on the + * bus to change the value by driving the bus high or low and switching to + * tristate. The argument is ignored. * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a * transition from say pull-up to pull-down implies that you disable * pull-up in the process, this setting disables all biasing. @@ -146,14 +152,6 @@ struct pinctrl_ops { * if for example some other pin is going to drive the signal connected * to it for a while. Pins used for input are usually always high * impedance. - * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it - * weakly drives the last value on a tristate bus, also known as a "bus - * holder", "bus keeper" or "repeater". This allows another device on the - * bus to change the value by driving the bus high or low and switching to - * tristate. The argument is ignored. - * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high - * impedance to VDD). If the argument is != 0 pull-up is enabled, - * if it is 0, pull-up is total, i.e. the pin is connected to VDD. * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high * impedance to GROUND). If the argument is != 0 pull-down is enabled, * if it is 0, pull-down is total, i.e. the pin is connected to GROUND. @@ -165,10 +163,9 @@ struct pinctrl_ops { * If the argument is != 0 pull up/down is enabled, if it is 0, the * configuration is ignored. The proper way to disable it is to use * @PIN_CONFIG_BIAS_DISABLE. - * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and - * low, this is the most typical case and is typically achieved with two - * active transistors on the output. Setting this config will enable - * push-pull mode, the argument is ignored. + * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high + * impedance to VDD). If the argument is != 0 pull-up is enabled, + * if it is 0, pull-up is total, i.e. the pin is connected to VDD. * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open * collector) which means it is usually wired with other output ports * which are then pulled up with an external resistor. Setting this @@ -176,59 +173,82 @@ struct pinctrl_ops { * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source * (open emitter). Setting this config will enable open source mode, the * argument is ignored. + * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and + * low, this is the most typical case and is typically achieved with two + * active transistors on the output. Setting this config will enable + * push-pull mode, the argument is ignored. * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current * passed as argument. The argument is in mA. + * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, + * which means it will wait for signals to settle when reading inputs. The + * argument gives the debounce time in usecs. Setting the + * argument to zero turns debouncing off. * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not * affect the pin's ability to drive output. 1 enables input, 0 disables * input. - * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. - * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, - * schmitt-trigger mode is disabled. * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, * the threshold value is given on a custom format as argument when * setting pins to this mode. - * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, - * which means it will wait for signals to settle when reading inputs. The - * argument gives the debounce time in usecs. Setting the - * argument to zero turns debouncing off. + * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. + * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, + * schmitt-trigger mode is disabled. + * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power + * operation, if several modes of operation are supported these can be + * passed in the argument on a custom form, else just use argument 1 + * to indicate low power mode, argument 0 turns low power mode off. + * @PIN_CONFIG_OUTPUT_ENABLE: this will enable the pin's output mode + * without driving a value there. For most platforms this reduces to + * enable the output buffers and then let the pin controller current + * configuration (eg. the currently selected mux function) drive values on + * the line. Use argument 1 to enable output mode, argument 0 to disable + * it. + * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a + * value on the line. Use argument 1 to indicate high level, argument 0 to + * indicate low level. (Please see Documentation/driver-api/pinctl.rst, + * section "GPIO mode pitfalls" for a discussion around this parameter.) * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power * supplies, the argument to this parameter (on a custom format) tells * the driver which alternative power source to use. + * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state. * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to * this parameter (on a custom format) tells the driver which alternative * slew rate to use. - * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power - * operation, if several modes of operation are supported these can be - * passed in the argument on a custom form, else just use argument 1 - * to indicate low power mode, argument 0 turns low power mode off. - * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument - * 1 to indicate high level, argument 0 to indicate low level. (Please - * see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a - * discussion around this parameter.) + * @PIN_CONFIG_SKEW_DELAY: if the pin has programmable skew rate (on inputs) + * or latch delay (on outputs) this parameter (in a custom format) + * specifies the clock skew or latch delay. It typically controls how + * many double inverters are put in front of the line. * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if * you need to pass in custom configurations to the pin controller, use * PIN_CONFIG_END+1 as the base offset. + * @PIN_CONFIG_MAX: this is the maximum configuration value that can be + * presented using the packed format. */ -#define PIN_CONFIG_BIAS_DISABLE 0 -#define PIN_CONFIG_BIAS_HIGH_IMPEDANCE 1 -#define PIN_CONFIG_BIAS_BUS_HOLD 2 -#define PIN_CONFIG_BIAS_PULL_UP 3 -#define PIN_CONFIG_BIAS_PULL_DOWN 4 -#define PIN_CONFIG_BIAS_PULL_PIN_DEFAULT 5 -#define PIN_CONFIG_DRIVE_PUSH_PULL 6 -#define PIN_CONFIG_DRIVE_OPEN_DRAIN 7 -#define PIN_CONFIG_DRIVE_OPEN_SOURCE 8 -#define PIN_CONFIG_DRIVE_STRENGTH 9 -#define PIN_CONFIG_INPUT_ENABLE 10 -#define PIN_CONFIG_INPUT_SCHMITT_ENABLE 11 -#define PIN_CONFIG_INPUT_SCHMITT 12 -#define PIN_CONFIG_INPUT_DEBOUNCE 13 -#define PIN_CONFIG_POWER_SOURCE 14 -#define PIN_CONFIG_SLEW_RATE 15 -#define PIN_CONFIG_LOW_POWER_MODE 16 -#define PIN_CONFIG_OUTPUT 17 -#define PIN_CONFIG_END 0x7FFF +enum pin_config_param { + PIN_CONFIG_BIAS_BUS_HOLD, + PIN_CONFIG_BIAS_DISABLE, + PIN_CONFIG_BIAS_HIGH_IMPEDANCE, + PIN_CONFIG_BIAS_PULL_DOWN, + PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, + PIN_CONFIG_BIAS_PULL_UP, + PIN_CONFIG_DRIVE_OPEN_DRAIN, + PIN_CONFIG_DRIVE_OPEN_SOURCE, + PIN_CONFIG_DRIVE_PUSH_PULL, + PIN_CONFIG_DRIVE_STRENGTH, + PIN_CONFIG_INPUT_DEBOUNCE, + PIN_CONFIG_INPUT_ENABLE, + PIN_CONFIG_INPUT_SCHMITT, + PIN_CONFIG_INPUT_SCHMITT_ENABLE, + PIN_CONFIG_LOW_POWER_MODE, + PIN_CONFIG_OUTPUT_ENABLE, + PIN_CONFIG_OUTPUT, + PIN_CONFIG_POWER_SOURCE, + PIN_CONFIG_SLEEP_HARDWARE_STATE, + PIN_CONFIG_SLEW_RATE, + PIN_CONFIG_SKEW_DELAY, + PIN_CONFIG_END = 0x7F, + PIN_CONFIG_MAX = 0xFF, +}; #if CONFIG_IS_ENABLED(PINCTRL_GENERIC) /** |