arm: am57xx: cl-som-am57x: remove board support

U-Boot support for the CL-SOM-AM57x module is no longer required.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>

12 files changed, 0 insertions, 1685 deletions

diff --git a/arch/arm/dts/am57xx-cl-som-am57x.dts b/arch/arm/dts/am57xx-cl-som-am57x.dts
deleted file mode 100644
index 203266f884..0000000000
--- a/arch/arm/dts/am57xx-cl-som-am57x.dts
+++ /dev/null
@@ -1,617 +0,0 @@
-/*
- * Support for CompuLab CL-SOM-AM57x System-on-Module
- *
- * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/
- * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published by
- * the Free Software Foundation.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "dra74x.dtsi"
-
-/ {
-	model = "CompuLab CL-SOM-AM57x";
-	compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x20000000>; /* 512 MB - minimal configuration */
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_pins_default>;
-
-		led0 {
-			label = "cl-som-am57x:green";
-			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
-	vdd_3v3: fixedregulator-vdd_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	ads7846reg: fixedregulator-ads7846-reg {
-		compatible = "regulator-fixed";
-		regulator-name = "ads7846-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	sound0: sound0 {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "CL-SOM-AM57x-Sound-Card";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink0_master>;
-		simple-audio-card,frame-master = <&dailink0_master>;
-		simple-audio-card,widgets =
-					"Headphone", "Headphone Jack",
-					"Microphone", "Microphone Jack",
-					"Line", "Line Jack";
-		simple-audio-card,routing =
-					"Headphone Jack", "RHPOUT",
-					"Headphone Jack", "LHPOUT",
-					"LLINEIN", "Line Jack",
-					"MICIN", "Mic Bias",
-					"Mic Bias", "Microphone Jack";
-
-		dailink0_master: simple-audio-card,cpu {
-			sound-dai = <&mcasp3>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&wm8731>;
-			system-clock-frequency = <12000000>;
-		};
-	};
-};
-
-&dra7_pmx_core {
-	leds_pins_default: leds_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x347c, PIN_OUTPUT | MUX_MODE14)	/* gpmc_a15.gpio2_5 */
-		>;
-	};
-
-	i2c1_pins_default: i2c1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
-		>;
-	};
-
-	i2c3_pins_default: i2c3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
-			DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
-		>;
-	};
-
-	i2c4_pins_default: i2c4_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36ac, PIN_INPUT| MUX_MODE10)	/* mcasp1_acl.i2c4_sda */
-			DRA7XX_CORE_IOPAD(0x36b0, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsr.i2c4_scl */
-		>;
-	};
-
-	tps659038_pins_default: tps659038_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-
-	qspi1_pins: pinmux_qspi1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3474, PIN_INPUT | MUX_MODE1)	/* gpmc_a13.qspi1_rtclk */
-			DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1)	/* gpmc_a16.qspi1_d0 */
-			DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1)	/* gpmc_a17.qspi1_d1 */
-			DRA7XX_CORE_IOPAD(0x3488, PIN_INPUT | MUX_MODE1)	/* qpmc_a18.qspi1_sclk */
-			DRA7XX_CORE_IOPAD(0x34b8, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs2.qspi1_cs0 */
-			DRA7XX_CORE_IOPAD(0x34bc, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs3.qspi1_cs1 */
-		>;
-	};
-
-	cpsw_pins_default: cpsw_pins_default {
-		pinctrl-single,pins = <
-			/* Slave at addr 0x0 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_tclk */
-			DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_tctl */
-			DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td3 */
-			DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td2 */
-			DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td1 */
-			DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td0 */
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rclk */
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rctl */
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd3 */
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd2 */
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd1 */
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd0 */
-
-			/* Slave at addr 0x1 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d12.rgmii1_tclk */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d13.rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d14.rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d15.rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d16.rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d17.rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
-		>;
-	};
-
-	cpsw_pins_sleep: cpsw_pins_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_pins_default: davinci_mdio_pins_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			DRA7XX_CORE_IOPAD(0x3590, PIN_OUTPUT_PULLUP | MUX_MODE3)/* vin2a_d10.mdio_mclk */
-			DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT_PULLUP | MUX_MODE3)	/* vin2a_d11.mdio_d */
-		>;
-	};
-
-	davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3590, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	ads7846_pins: pinmux_ads7846_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3464, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpmc_a9.gpio1_31 */
-		>;
-	};
-
-	mcasp3_pins_default: mcasp3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
-		>;
-	};
-
-	mcasp3_pins_sleep: mcasp3_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-};
-
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_default>;
-	clock-frequency = <400000>;
-};
-
-&i2c3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins_default>;
-	clock-frequency = <400000>;
-};
-
-&i2c4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c4_pins_default>;
-	clock-frequency = <400000>;
-
-	tps659038: tps659038@58 {
-		compatible = "ti,tps659038";
-		reg = <0x58>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tps659038_pins_default>;
-
-		#interrupt-cells = <2>;
-		interrupt-controller;
-
-		ti,system-power-controller;
-
-		tps659038_pmic {
-			compatible = "ti,tps659038-pmic";
-
-			regulators {
-				smps12_reg: smps12 {
-					/* VDD_MPU */
-					regulator-name = "smps12";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps3_reg: smps3 {
-					/* VDD_DDR */
-					regulator-name = "smps3";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps45_reg: smps45 {
-					/* VDD_DSPEVE */
-					regulator-name = "smps45";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps6_reg: smps6 {
-					/* VDD_GPU */
-					regulator-name = "smps6";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps7_reg: smps7 {
-					/* VDD_CORE */
-					regulator-name = "smps7";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1160000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps8_reg: smps8 {
-					/* VDD_IVA */
-					regulator-name = "smps8";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps9_reg: smps9 {
-					/* PMIC_3V3 */
-					regulator-name = "smps9";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-
-				ldo1_reg: ldo1 {
-					/* VDD_SD / VDDSHV8  */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo2_reg: ldo2 {
-					/* VDD_1V8 */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHYA - supplies VDDA_SATA, VDDA_USB1/2/3 */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDA_1V8_PHYB - supplies VDDA_HDMI, VDDA_PCIE/0/1 */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo9_reg: ldo9 {
-					/* VDD_RTC */
-					regulator-name = "ldo9";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldoln_reg: ldoln {
-					/* VDDA_1V8_PLL */
-					regulator-name = "ldoln";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldousb_reg: ldousb {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldousb";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				/* regen1 not used */
-			};
-		};
-
-		tps659038_pwr_button: tps659038_pwr_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&tps659038>;
-			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-			ti,palmas-long-press-seconds = <12>;
-		};
-
-		tps659038_gpio: tps659038_gpio {
-			compatible = "ti,palmas-gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-	};
-
-	rtc0: rtc@56 {
-		compatible = "emmicro,em3027";
-		reg = <0x56>;
-	};
-
-	eeprom_module: atmel@50 {
-		compatible = "atmel,24c08";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-
-	wm8731: wm8731@1a {
-		#sound-dai-cells = <0>;
-		compatible = "wlf,wm8731";
-		reg = <0x1a>;
-		status = "okay";
-	};
-};
-
-&cpu0 {
-	cpu0-supply = <&smps12_reg>;
-	voltage-tolerance = <1>;
-};
-
-&sata {
-	status = "okay";
-};
-
-&mailbox5 {
-	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
-};
-
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
-};
-
-&mmc2 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_default>;
-
-	vmmc-supply = <&vdd_3v3>;
-	bus-width = <8>;
-	ti,non-removable;
-	cap-mmc-dual-data-rate;
-};
-
-&qspi {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi1_pins>;
-
-	spi-max-frequency = <48000000>;
-
-	spi_flash: spi_flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spansion,m25p80", "jedec,spi-nor";
-		reg = <0>;				/* CS0 */
-		spi-max-frequency = <48000000>;
-
-		partition@0 {
-			label = "uboot";
-			reg = <0x0 0xc0000>;
-		};
-
-		partition@c0000 {
-			label = "uboot environment";
-			reg = <0xc0000 0x40000>;
-		};
-
-		partition@100000 {
-			label = "reserved";
-			reg = <0x100000 0x0>;
-		};
-	};
-
-	/* touch controller */
-	ads7846@0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&ads7846_pins>;
-
-		compatible = "ti,ads7846";
-		vcc-supply = <&ads7846reg>;
-
-		reg = <1>;                              /* CS1 */
-		spi-max-frequency = <1500000>;
-
-		interrupt-parent = <&gpio1>;
-		interrupts = <31 0>;
-		pendown-gpio = <&gpio1 31 0>;
-
-
-		ti,x-min = /bits/ 16 <0x0>;
-		ti,x-max = /bits/ 16 <0x0fff>;
-		ti,y-min = /bits/ 16 <0x0>;
-		ti,y-max = /bits/ 16 <0x0fff>;
-
-		ti,x-plate-ohms = /bits/ 16 <180>;
-		ti,pressure-max = /bits/ 16 <255>;
-
-		ti,debounce-max = /bits/ 16 <30>;
-		ti,debounce-tol = /bits/ 16 <10>;
-		ti,debounce-rep = /bits/ 16 <1>;
-
-		wakeup-source;
-	};
-};
-
-&mac {
-	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_pins_default>;
-	pinctrl-1 = <&cpsw_pins_sleep>;
-	dual_emac;
-};
-
-&cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <0>;
-};
-
-&cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <1>;
-};
-
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_pins_default>;
-	pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
-&usb2_phy1 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb2_phy2 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb1 {
-	dr_mode = "host";
-};
-
-&usb2 {
-	dr_mode = "host";
-};
-
-&mcasp3 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins_default>;
-	pinctrl-1 = <&mcasp3_pins_sleep>;
-	status = "okay";
-
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	/* 4 serializers */
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-		1 2 0 0
-	>;
-};
-
-&gpio3 {
-	status = "okay";
-	ti,no-reset-on-init;
-};
-
-&gpio2 {
-	status = "okay";
-	ti,no-reset-on-init;
-};
diff --git a/arch/arm/dts/am57xx-sbc-am57x.dts b/arch/arm/dts/am57xx-sbc-am57x.dts
deleted file mode 100644
index 31f9be6324..0000000000
--- a/arch/arm/dts/am57xx-sbc-am57x.dts
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Support for CompuLab SBC-AM57x single board computer
- *
- * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/
- * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published by
- * the Free Software Foundation.
- */
-
-#include "am57xx-cl-som-am57x.dts"
-#include "compulab-sb-som.dtsi"
-
-/ {
-	model = "CompuLab CL-SOM-AM57x on SB-SOM-AM57x";
-	compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
-
-	aliases {
-		display0 = &lcd0;
-		display1 = &hdmi;
-	};
-};
-
-&dra7_pmx_core {
-	uart3_pins_default: uart3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_txd */
-		>;
-	};
-
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1_sdcd.gpio6_27 */
-			DRA7XX_CORE_IOPAD(0x377c, PIN_INPUT | MUX_MODE14)	/* mmc1_sdwp.gpio6_28 */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-		>;
-	};
-
-	i2c5_pins_default: i2c5_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT| MUX_MODE10)	/* mcasp1_axr0.i2c5_sda */
-			DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT| MUX_MODE10)	/* mcasp1_axr1.i2c5_scl */
-		>;
-	};
-
-	lcd_pins_default: lcd_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3564, PIN_OUTPUT | MUX_MODE14)      /* vin2a_vsync0.gpio4_0 */
-		>;
-	};
-
-	hdmi_pins: pinmux_hdmi_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1)	/* i2c2_sda.hdmi1_ddc_scl */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1)	/* i2c2_scl.hdmi1_ddc_sda */
-		>;
-	};
-
-	hdmi_conn_pins: pinmux_hdmi_conn_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT | MUX_MODE14)	/* spi1_cs2.gpio7_12 */
-		>;
-	};
-};
-
-&uart3 {
-	status = "okay";
-	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x3f8>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_default>;
-};
-
-&mmc1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-
-	vmmc-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
-};
-
-&usb1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
-};
-
-&i2c5 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_default>;
-	clock-frequency = <400000>;
-
-	eeprom_base: atmel@54 {
-		compatible = "atmel,24c08";
-		reg = <0x54>;
-		pagesize = <16>;
-	};
-
-	pca9555: pca9555@20 {
-		compatible = "nxp,pca9555";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};
-
-&dss {
-	status = "ok";
-
-	vdda_video-supply = <&ldoln_reg>;
-
-	port {
-		dpi_lcd_out: endpoint {
-			remote-endpoint = <&lcd_in>;
-			data-lines = <24>;
-		};
-	};
-};
-
-&lcd0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&lcd_pins_default>;
-
-	enable-gpios = <&pca9555 14 GPIO_ACTIVE_HIGH
-			&gpio4 0 GPIO_ACTIVE_HIGH>;
-
-	port {
-		lcd_in: endpoint {
-			remote-endpoint = <&dpi_lcd_out>;
-			data-lines = <24>;
-		};
-	};
-};
-
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo4_reg>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_pins>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&hdmi_connector_in>;
-			lanes = <1 0 3 2 5 4 7 6>;
-		};
-	};
-};
-
-&hdmi_conn {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_conn_pins>;
-
-	hpd-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-
-	port {
-		hdmi_connector_in: endpoint {
-			remote-endpoint = <&hdmi_out>;
-		};
-	};
-};
diff --git a/arch/arm/mach-omap2/omap5/Kconfig b/arch/arm/mach-omap2/omap5/Kconfig
index f083a4a385..fddbac9dec 100644
--- a/arch/arm/mach-omap2/omap5/Kconfig
+++ b/arch/arm/mach-omap2/omap5/Kconfig
@@ -9,10 +9,6 @@ choice
 	prompt "OMAP5 board select"
 	optional
 
-config TARGET_CL_SOM_AM57X
-	bool "CompuLab CL-SOM-AM57x"
-	select DRA7XX
-
 config TARGET_CM_T54
 	bool "CompuLab CM-T54"
 
@@ -160,7 +156,6 @@ endchoice
 endmenu
 endif
 
-source "board/compulab/cl-som-am57x/Kconfig"
 source "board/compulab/cm_t54/Kconfig"
 source "board/ti/omap5_uevm/Kconfig"
 source "board/ti/dra7xx/Kconfig"
diff --git a/board/compulab/cl-som-am57x/Kconfig b/board/compulab/cl-som-am57x/Kconfig
deleted file mode 100644
index 85fc9a1fdb..0000000000
--- a/board/compulab/cl-som-am57x/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_CL_SOM_AM57X
-
-config SYS_BOARD
-	default "cl-som-am57x"
-
-config SYS_VENDOR
-	default "compulab"
-
-config SYS_CONFIG_NAME
-	default "cl-som-am57x"
-
-endif
diff --git a/board/compulab/cl-som-am57x/MAINTAINERS b/board/compulab/cl-som-am57x/MAINTAINERS
deleted file mode 100644
index e0195f4610..0000000000
--- a/board/compulab/cl-som-am57x/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-CL-SOM-AM57x BOARD
-M:	Uri Mashiach <uri.mashiach@compulab.co.il>
-S:	Maintained
-F:	board/compulab/cl-som-am57x/
-F:	include/configs/cl-som-am57x.h
-F:	configs/cl-som-am57x_defconfig
diff --git a/board/compulab/cl-som-am57x/Makefile b/board/compulab/cl-som-am57x/Makefile
deleted file mode 100644
index 566366bf6e..0000000000
--- a/board/compulab/cl-som-am57x/Makefile
+++ /dev/null
@@ -1,17 +0,0 @@
-#
-# Makefile
-#
-# (C) Copyright 2016 CompuLab, Ltd. <www.compulab.co.il>
-#
-# Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
-#
-# SPDX-License-Identifier:     GPL-2.0+
-#
-
-ifdef CONFIG_SPL_BUILD
-obj-y	+= spl.o mux.o
-else
-obj-y	+= cl-som-am57x.o mux.o
-endif
-
-obj-$(CONFIG_DRIVER_TI_CPSW)	+= eth.o
diff --git a/board/compulab/cl-som-am57x/cl-som-am57x.c b/board/compulab/cl-som-am57x/cl-som-am57x.c
deleted file mode 100644
index fcba2a0e2a..0000000000
--- a/board/compulab/cl-som-am57x/cl-som-am57x.c
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Board functions for CompuLab cl_som_am57x board
- *
- * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
- *
- * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- */
-
-#include <common.h>
-#include <palmas.h>
-#include <usb.h>
-#include <asm/gpio.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/sys_proto.h>
-#include "../common/common.h"
-#include "../common/eeprom.h"
-#include <asm/omap_common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct omap_sysinfo sysinfo = {
-	"Board: CL-SOM-AM57x\n"
-};
-
-int board_init(void)
-{
-	/* Disable PMIC Powerhold feature, DEV_CTRL.DEV_ON = 1 */
-	palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
-
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-	return 0;
-}
-
-#ifdef CONFIG_MMC
-#define SB_SOM_CD_GPIO 187
-#define SB_SOM_WP_GPIO 188
-
-int board_mmc_init(bd_t *bis)
-{
-	int ret0, ret1;
-
-	ret0 = omap_mmc_init(0, 0, 0, SB_SOM_CD_GPIO, SB_SOM_WP_GPIO);
-	if (ret0)
-		printf("cl-som-am57x: failed to initialize mmc0\n");
-
-	ret1 = omap_mmc_init(1, 0, 0, -1, -1);
-	if (ret1)
-		printf("cl-som-am57x: failed to initialize mmc1\n");
-
-	return ret0 && ret1;
-}
-#endif /* CONFIG_MMC */
-
-int misc_init_r(void)
-{
-	cl_print_pcb_info();
-
-	return 0;
-}
-
-u32 get_board_rev(void)
-{
-	return cl_eeprom_get_board_rev(CONFIG_SYS_I2C_EEPROM_BUS);
-}
-
-int board_usb_init(int index, enum usb_init_type init)
-{
-	enable_usb_clocks(index);
-	return 0;
-}
-
-int board_usb_cleanup(int index, enum usb_init_type init)
-{
-	disable_usb_clocks(index);
-	return 0;
-}
diff --git a/board/compulab/cl-som-am57x/eth.c b/board/compulab/cl-som-am57x/eth.c
deleted file mode 100644
index 3c59457341..0000000000
--- a/board/compulab/cl-som-am57x/eth.c
+++ /dev/null
@@ -1,198 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Ethernet specific code for CompuLab CL-SOM-AM57x module
- *
- * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
- *
- * Author: Uri Mashiach <uri.mashiach@compulab.co.il>
- */
-
-#include <common.h>
-#include <cpsw.h>
-#include <environment.h>
-#include <miiphy.h>
-#include <asm/gpio.h>
-#include <asm/arch/sys_proto.h>
-#include "../common/eeprom.h"
-
-static void cpsw_control(int enabled)
-{
-	/* VTP can be added here */
-}
-
-static struct cpsw_slave_data cl_som_am57x_cpsw_slaves[] = {
-	{
-		.slave_reg_ofs	= 0x208,
-		.sliver_reg_ofs	= 0xd80,
-		.phy_addr	= 0,
-		.phy_if         = PHY_INTERFACE_MODE_RMII,
-	},
-	{
-		.slave_reg_ofs	= 0x308,
-		.sliver_reg_ofs	= 0xdc0,
-		.phy_addr	= 1,
-		.phy_if         = PHY_INTERFACE_MODE_RMII,
-
-	},
-};
-
-static struct cpsw_platform_data cl_som_am57_cpsw_data = {
-	.mdio_base		= CPSW_MDIO_BASE,
-	.cpsw_base		= CPSW_BASE,
-	.mdio_div		= 0xff,
-	.channels		= 8,
-	.cpdma_reg_ofs		= 0x800,
-	.slaves			= 2,
-	.slave_data		= cl_som_am57x_cpsw_slaves,
-	.ale_reg_ofs		= 0xd00,
-	.ale_entries		= 1024,
-	.host_port_reg_ofs	= 0x108,
-	.hw_stats_reg_ofs	= 0x900,
-	.bd_ram_ofs		= 0x2000,
-	.mac_control		= (1 << 5),
-	.control		= cpsw_control,
-	.host_port_num		= 0,
-	.version		= CPSW_CTRL_VERSION_2,
-};
-
-/*
- * cl_som_am57x_efuse_read_mac_addr() - read Ethernet port MAC address.
- *       The information is retrieved from the SOC's registers.
- * @buff: read buffer.
- * @port_num: port number.
- */
-static void cl_som_am57x_efuse_read_mac_addr(uchar *buff, uint port_num)
-{
-	uint32_t mac_hi, mac_lo;
-
-	if (port_num) {
-		mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
-		mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
-	} else {
-		mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
-		mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
-	}
-
-	buff[0] = (mac_hi & 0xFF0000) >> 16;
-	buff[1] = (mac_hi & 0xFF00) >> 8;
-	buff[2] = mac_hi & 0xFF;
-	buff[3] = (mac_lo & 0xFF0000) >> 16;
-	buff[4] = (mac_lo & 0xFF00) >> 8;
-	buff[5] = mac_lo & 0xFF;
-}
-
-/*
- * cl_som_am57x_handle_mac_address() - set MAC address in the U-Boot
- *	environment.
- *      The address is retrieved retrieved from an EEPROM field or from the
- *	SOC's registers.
- * @env_name: U-Boot environment name.
- * @field_name: EEPROM field name.
- * @port_num: SOC's port number.
- */
-static int cl_som_am57x_handle_mac_address(char *env_name, uint port_num)
-{
-	int ret;
-	uint8_t enetaddr[6];
-
-	ret = eth_env_get_enetaddr(env_name, enetaddr);
-	if (ret)
-		return 0;
-
-	ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
-
-	if (ret || !is_valid_ethaddr(enetaddr))
-		cl_som_am57x_efuse_read_mac_addr(enetaddr, port_num);
-
-	if (!is_valid_ethaddr(enetaddr))
-		return -1;
-
-	ret = eth_env_set_enetaddr(env_name, enetaddr);
-	if (ret)
-		printf("cl-som-am57x: Failed to set Eth port %d MAC address\n",
-		       port_num);
-
-	return ret;
-}
-
-#define CL_SOM_AM57X_PHY_ADDR2			0x01
-#define AR8033_PHY_DEBUG_ADDR_REG		0x1d
-#define AR8033_PHY_DEBUG_DATA_REG		0x1e
-#define AR8033_DEBUG_RGMII_RX_CLK_DLY_REG	0x00
-#define AR8033_DEBUG_RGMII_TX_CLK_DLY_REG	0x05
-#define AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK	(1 << 15)
-#define AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK	(1 << 8)
-
-/*
- * cl_som_am57x_rgmii_clk_delay() - Set RGMII clock delay.
- *	Enable RX delay, disable TX delay.
- */
-static void cl_som_am57x_rgmii_clk_delay(void)
-{
-	uint16_t mii_reg_val;
-	const char *devname;
-
-	devname = miiphy_get_current_dev();
-	/* PHY 2 */
-	miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG,
-		     AR8033_DEBUG_RGMII_RX_CLK_DLY_REG);
-	miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
-		    &mii_reg_val);
-	mii_reg_val |= AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK;
-	miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
-		     mii_reg_val);
-
-	miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG,
-		     AR8033_DEBUG_RGMII_TX_CLK_DLY_REG);
-	miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
-		    &mii_reg_val);
-	mii_reg_val &= ~AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK;
-	miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG,
-		     mii_reg_val);
-}
-
-#define CL_SOM_AM57X_GPIO_PHY1_RST 92 /* GPIO3_28 */
-#define CL_SOM_AM57X_RGMII_PORT1 1
-
-int board_eth_init(bd_t *bis)
-{
-	int ret;
-	uint32_t ctrl_val;
-	char *cpsw_phy_envval;
-	int cpsw_act_phy = 1;
-
-	/* SB-SOM-AM57x primary Eth (P21) is routed to RGMII1 */
-	ret = cl_som_am57x_handle_mac_address("ethaddr",
-					      CL_SOM_AM57X_RGMII_PORT1);
-
-	if (ret)
-		return -1;
-
-	/* Select RGMII for GMII1_SEL */
-	ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
-	ctrl_val |= 0x22;
-	writel(ctrl_val, (*ctrl)->control_core_control_io1);
-	mdelay(10);
-
-	gpio_request(CL_SOM_AM57X_GPIO_PHY1_RST, "phy1_rst");
-	gpio_direction_output(CL_SOM_AM57X_GPIO_PHY1_RST, 0);
-	mdelay(20);
-
-	gpio_set_value(CL_SOM_AM57X_GPIO_PHY1_RST, 1);
-	mdelay(20);
-
-	cpsw_phy_envval = env_get("cpsw_phy");
-	if (cpsw_phy_envval != NULL)
-		cpsw_act_phy = simple_strtoul(cpsw_phy_envval, NULL, 0);
-
-	cl_som_am57_cpsw_data.active_slave = cpsw_act_phy;
-
-	ret = cpsw_register(&cl_som_am57_cpsw_data);
-	if (ret < 0)
-		printf("Error %d registering CPSW switch\n", ret);
-
-	/* Set RGMII clock delay */
-	cl_som_am57x_rgmii_clk_delay();
-
-	return ret;
-}
diff --git a/board/compulab/cl-som-am57x/mux.c b/board/compulab/cl-som-am57x/mux.c
deleted file mode 100644
index 050f2aa3ef..0000000000
--- a/board/compulab/cl-som-am57x/mux.c
+++ /dev/null
@@ -1,123 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Pinmux configuration for CompuLab CL-SOM-AM57x board
- *
- * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
- *
- * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- */
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mux_dra7xx.h>
-
-/* Serial console */
-static const struct pad_conf_entry cl_som_am57x_padconf_console[] = {
-	{UART3_RXD, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* UART3_RXD */
-	{UART3_TXD, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* UART3_TXD */
-};
-
-/* PMIC I2C */
-static const struct pad_conf_entry cl_som_am57x_padconf_pmic[] = {
-	{MCASP1_ACLKR, (M10 | PIN_INPUT)}, /* MCASP1_ACLKR.I2C4_SDA */
-	{MCASP1_FSR,   (M10 | PIN_INPUT)}, /* MCASP1_FSR.I2C4_SCL */
-};
-
-/* Green GPIO led */
-static const struct pad_conf_entry cl_som_am57x_padconf_green_led[] = {
-	{GPMC_A15, (M14 | PIN_OUTPUT_PULLDOWN)}, /* GPMC_A15.GPIO2_5 */
-};
-
-/* MMC/SD Card */
-static const struct pad_conf_entry cl_som_am57x_padconf_sd_card[] = {
-	{MMC1_CLK,  (M0  | PIN_INPUT_PULLUP)}, /* MMC1_CLK */
-	{MMC1_CMD,  (M0  | PIN_INPUT_PULLUP)}, /* MMC1_CMD */
-	{MMC1_DAT0, (M0  | PIN_INPUT_PULLUP)}, /* MMC1_DAT0 */
-	{MMC1_DAT1, (M0  | PIN_INPUT_PULLUP)}, /* MMC1_DAT1 */
-	{MMC1_DAT2, (M0  | PIN_INPUT_PULLUP)}, /* MMC1_DAT2 */
-	{MMC1_DAT3, (M0  | PIN_INPUT_PULLUP)}, /* MMC1_DAT3 */
-	{MMC1_SDCD, (M14 | PIN_INPUT)       }, /* MMC1_SDCD */
-	{MMC1_SDWP, (M14 | PIN_INPUT)       }, /* MMC1_SDWP */
-};
-
-/* WiFi - must be in the safe mode on boot */
-static const struct pad_conf_entry cl_som_am57x_padconf_wifi[] = {
-	{UART1_CTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART1_CTSN */
-	{UART1_RTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART1_RTSN */
-	{UART2_RXD,  (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_RXD */
-	{UART2_TXD,  (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_TXD */
-	{UART2_CTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_CTSN */
-	{UART2_RTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_RTSN */
-};
-
-/* QSPI */
-static const struct pad_conf_entry cl_som_am57x_padconf_qspi[] = {
-	{GPMC_A13, (M1 | PIN_INPUT)       }, /* GPMC_A13.QSPI1_RTCLK */
-	{GPMC_A18, (M1 | PIN_INPUT)       }, /* GPMC_A18.QSPI1_SCLK */
-	{GPMC_A16, (M1 | PIN_INPUT)       }, /* GPMC_A16.QSPI1_D0 */
-	{GPMC_A17, (M1 | PIN_INPUT)       }, /* GPMC_A17.QSPI1_D1 */
-	{GPMC_CS2, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_CS2.QSPI1_CS0 */
-};
-
-/* GPIO Expander I2C */
-static const struct pad_conf_entry cl_som_am57x_padconf_i2c_gpio[] = {
-	{MCASP1_AXR0, (M10 | PIN_INPUT)}, /* MCASP1_AXR0.I2C5_SDA */
-	{MCASP1_AXR1, (M10 | PIN_INPUT)}, /* MCASP1_AXR1.I2C5_SCL */
-};
-
-/* eMMC internal storage */
-static const struct pad_conf_entry cl_som_am57x_padconf_emmc[] = {
-	{GPMC_A19, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A19.MMC2_DAT4 */
-	{GPMC_A20, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A20.MMC2_DAT5 */
-	{GPMC_A21, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A21.MMC2_DAT6 */
-	{GPMC_A22, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A22.MMC2_DAT7 */
-	{GPMC_A23, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A23.MMC2_CLK */
-	{GPMC_A24, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A24.MMC2_DAT0 */
-	{GPMC_A25, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A25.MMC2_DAT1 */
-	{GPMC_A26, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A26.MMC2_DAT2 */
-	{GPMC_A27, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A27.MMC2_DAT3 */
-	{GPMC_CS1, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_CS1.MMC2_CMD */
-};
-
-/* usb1_drvvbus */
-static const struct pad_conf_entry cl_som_am57x_padconf_usb[] = {
-	/* USB1_DRVVBUS.USB1_DRVVBUS */
-	{USB1_DRVVBUS, (M0 | PIN_OUTPUT_PULLDOWN | SLEWCONTROL) },
-};
-
-/* Ethernet */
-static const struct pad_conf_entry cl_som_am57x_padconf_ethernet[] = {
-	/* MDIO bus */
-	{VIN2A_D10,  (M3  | PIN_OUTPUT_PULLUP) }, /* VIN2A_D10.MDIO_MCLK  */
-	{VIN2A_D11,  (M3  | PIN_INPUT_PULLUP)  }, /* VIN2A_D11.MDIO_D  */
-	/* EMAC Slave 1 at addr 0x1 - Default interface */
-	{VIN2A_D12,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D12.RGMII1_TXC */
-	{VIN2A_D13,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D13.RGMII1_TXCTL */
-	{VIN2A_D14,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D14.RGMII1_TXD3 */
-	{VIN2A_D15,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D15.RGMII1_TXD2 */
-	{VIN2A_D16,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D16.RGMII1_TXD1 */
-	{VIN2A_D17,  (M3  | PIN_OUTPUT)         }, /* VIN2A_D17.RGMII1_TXD0 */
-	{VIN2A_D18,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D18.RGMII1_RXC */
-	{VIN2A_D19,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D19.RGMII1_RXCTL */
-	{VIN2A_D20,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D20.RGMII1_RXD3 */
-	{VIN2A_D21,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D21.RGMII1_RXD2 */
-	{VIN2A_D22,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D22.RGMII1_RXD1 */
-	{VIN2A_D23,  (M3  | PIN_INPUT_PULLDOWN) }, /* VIN2A_D23.RGMII1_RXD0 */
-	/* Eth PHY1 reset GPIOs*/
-	{VIN2A_CLK0, (M14 | PIN_OUTPUT_PULLDOWN)}, /* VIN2A_CLK0.GPIO3_28 */
-};
-
-#define SET_MUX(mux_array) do_set_mux32((*ctrl)->control_padconf_core_base, \
-					mux_array, ARRAY_SIZE(mux_array))
-
-void set_muxconf_regs(void)
-{
-	SET_MUX(cl_som_am57x_padconf_console);
-	SET_MUX(cl_som_am57x_padconf_pmic);
-	SET_MUX(cl_som_am57x_padconf_green_led);
-	SET_MUX(cl_som_am57x_padconf_sd_card);
-	SET_MUX(cl_som_am57x_padconf_wifi);
-	SET_MUX(cl_som_am57x_padconf_qspi);
-	SET_MUX(cl_som_am57x_padconf_i2c_gpio);
-	SET_MUX(cl_som_am57x_padconf_emmc);
-	SET_MUX(cl_som_am57x_padconf_usb);
-	SET_MUX(cl_som_am57x_padconf_ethernet);
-}
diff --git a/board/compulab/cl-som-am57x/spl.c b/board/compulab/cl-som-am57x/spl.c
deleted file mode 100644
index 0fb3d84a02..0000000000
--- a/board/compulab/cl-som-am57x/spl.c
+++ /dev/null
@@ -1,238 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SPL data and initialization for CompuLab CL-SOM-AM57x board
- *
- * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
- *
- * Author: Uri Mashiach <uri.mashiach@compulab.co.il>
- */
-
-#include <asm/emif.h>
-#include <asm/omap_common.h>
-#include <asm/arch/sys_proto.h>
-
-static const struct dmm_lisa_map_regs cl_som_am57x_lisa_regs = {
-	.dmm_lisa_map_3 = 0x80740300,
-	.is_ma_present  = 0x1
-};
-
-void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
-{
-	/* Disable SDRAM controller EMIF2 for single core SOC */
-	*dmm_lisa_regs = &cl_som_am57x_lisa_regs;
-	if (omap_revision() == DRA722_ES1_0) {
-		((struct dmm_lisa_map_regs *) *dmm_lisa_regs)->dmm_lisa_map_3 =
-		  0x80640100;
-	}
-}
-
-static const struct emif_regs cl_som_am57x_emif1_ddr3_532mhz_emif_regs = {
-	.sdram_config_init	= 0x61852332,
-	.sdram_config		= 0x61852332,
-	.sdram_config2		= 0x00000000,
-	.ref_ctrl		= 0x000040f1,
-	.ref_ctrl_final		= 0x00001040,
-	.sdram_tim1		= 0xeeef36f3,
-	.sdram_tim2		= 0x348f7fda,
-	.sdram_tim3		= 0x027f88a8,
-	.read_idle_ctrl		= 0x00050000,
-	.zq_config		= 0x1007190b,
-	.temp_alert_config	= 0x00000000,
-	.emif_ddr_phy_ctlr_1_init = 0x0034400b,
-	.emif_ddr_phy_ctlr_1	= 0x0e34400b,
-	.emif_ddr_ext_phy_ctrl_1 = 0x04040100,
-	.emif_ddr_ext_phy_ctrl_2 = 0x00740074,
-	.emif_ddr_ext_phy_ctrl_3 = 0x00780078,
-	.emif_ddr_ext_phy_ctrl_4 = 0x007c007c,
-	.emif_ddr_ext_phy_ctrl_5 = 0x007b007b,
-	.emif_rd_wr_lvl_rmp_win	= 0x00000000,
-	.emif_rd_wr_lvl_rmp_ctl	= 0x80000000,
-	.emif_rd_wr_lvl_ctl	= 0x00000000,
-	.emif_rd_wr_exec_thresh	= 0x00000305
-};
-
-/* Ext phy ctrl regs 1-35 */
-static const u32 cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs[] = {
-	0x10040100,
-	0x00740074,
-	0x00780078,
-	0x007c007c,
-	0x007b007b,
-	0x00800080,
-	0x00360036,
-	0x00340034,
-	0x00360036,
-	0x00350035,
-	0x00350035,
-
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-
-	0x00430043,
-	0x003e003e,
-	0x004a004a,
-	0x00470047,
-	0x00400040,
-
-	0x00000000,
-	0x00600020,
-	0x40011080,
-	0x08102040,
-
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x0,
-	0x0,
-	0x0,
-	0x0,
-	0x0
-};
-
-static const struct emif_regs cl_som_am57x_emif2_ddr3_532mhz_emif_regs = {
-	.sdram_config_init	= 0x61852332,
-	.sdram_config		= 0x61852332,
-	.sdram_config2		= 0x00000000,
-	.ref_ctrl		= 0x000040f1,
-	.ref_ctrl_final		= 0x00001040,
-	.sdram_tim1		= 0xeeef36f3,
-	.sdram_tim2		= 0x348f7fda,
-	.sdram_tim3		= 0x027f88a8,
-	.read_idle_ctrl		= 0x00050000,
-	.zq_config		= 0x1007190b,
-	.temp_alert_config	= 0x00000000,
-	.emif_ddr_phy_ctlr_1_init = 0x0034400b,
-	.emif_ddr_phy_ctlr_1	= 0x0e34400b,
-	.emif_ddr_ext_phy_ctrl_1 = 0x04040100,
-	.emif_ddr_ext_phy_ctrl_2 = 0x00740074,
-	.emif_ddr_ext_phy_ctrl_3 = 0x00780078,
-	.emif_ddr_ext_phy_ctrl_4 = 0x007c007c,
-	.emif_ddr_ext_phy_ctrl_5 = 0x007b007b,
-	.emif_rd_wr_lvl_rmp_win	= 0x00000000,
-	.emif_rd_wr_lvl_rmp_ctl	= 0x80000000,
-	.emif_rd_wr_lvl_ctl	= 0x00000000,
-	.emif_rd_wr_exec_thresh	= 0x00000305
-};
-
-static const u32 cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs[] = {
-	0x10040100,
-	0x00820082,
-	0x008b008b,
-	0x00800080,
-	0x007e007e,
-	0x00800080,
-	0x00370037,
-	0x00390039,
-	0x00360036,
-	0x00370037,
-	0x00350035,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x01ff01ff,
-	0x00540054,
-	0x00540054,
-	0x004e004e,
-	0x004c004c,
-	0x00400040,
-
-	0x00000000,
-	0x00600020,
-	0x40011080,
-	0x08102040,
-
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x00400040,
-	0x0,
-	0x0,
-	0x0,
-	0x0,
-	0x0
-};
-
-static struct vcores_data cl_som_am57x_volts = {
-	.mpu.value[OPP_NOM]	= VDD_MPU_DRA7_NOM,
-	.mpu.efuse.reg[OPP_NOM]	= STD_FUSE_OPP_VMIN_MPU_NOM,
-	.mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
-	.mpu.addr		= TPS659038_REG_ADDR_SMPS12,
-	.mpu.pmic		= &tps659038,
-
-	.eve.value[OPP_NOM]	= VDD_EVE_DRA7_NOM,
-	.eve.value[OPP_OD]	= VDD_EVE_DRA7_OD,
-	.eve.value[OPP_HIGH]	= VDD_EVE_DRA7_HIGH,
-	.eve.efuse.reg[OPP_NOM]	= STD_FUSE_OPP_VMIN_DSPEVE_NOM,
-	.eve.efuse.reg[OPP_OD]	= STD_FUSE_OPP_VMIN_DSPEVE_OD,
-	.eve.efuse.reg[OPP_HIGH]	= STD_FUSE_OPP_VMIN_DSPEVE_HIGH,
-	.eve.efuse.reg_bits	= DRA752_EFUSE_REGBITS,
-	.eve.addr		= TPS659038_REG_ADDR_SMPS45,
-	.eve.pmic		= &tps659038,
-
-	.gpu.value[OPP_NOM]	= VDD_GPU_DRA7_NOM,
-	.gpu.value[OPP_OD]	= VDD_GPU_DRA7_OD,
-	.gpu.value[OPP_HIGH]	= VDD_GPU_DRA7_HIGH,
-	.gpu.efuse.reg[OPP_NOM]	= STD_FUSE_OPP_VMIN_GPU_NOM,
-	.gpu.efuse.reg[OPP_OD]	= STD_FUSE_OPP_VMIN_GPU_OD,
-	.gpu.efuse.reg[OPP_HIGH]	= STD_FUSE_OPP_VMIN_GPU_HIGH,
-	.gpu.efuse.reg_bits	= DRA752_EFUSE_REGBITS,
-	.gpu.addr		= TPS659038_REG_ADDR_SMPS6,
-	.gpu.pmic		= &tps659038,
-
-	.core.value[OPP_NOM]	= VDD_CORE_DRA7_NOM,
-	.core.efuse.reg[OPP_NOM]	= STD_FUSE_OPP_VMIN_CORE_NOM,
-	.core.efuse.reg_bits	= DRA752_EFUSE_REGBITS,
-	.core.addr		= TPS659038_REG_ADDR_SMPS7,
-	.core.pmic		= &tps659038,
-
-	.iva.value[OPP_NOM]	= VDD_IVA_DRA7_NOM,
-	.iva.value[OPP_OD]	= VDD_IVA_DRA7_OD,
-	.iva.value[OPP_HIGH]	= VDD_IVA_DRA7_HIGH,
-	.iva.efuse.reg[OPP_NOM]	= STD_FUSE_OPP_VMIN_IVA_NOM,
-	.iva.efuse.reg[OPP_OD]	= STD_FUSE_OPP_VMIN_IVA_OD,
-	.iva.efuse.reg[OPP_HIGH]	= STD_FUSE_OPP_VMIN_IVA_HIGH,
-	.iva.efuse.reg_bits	= DRA752_EFUSE_REGBITS,
-	.iva.addr		= TPS659038_REG_ADDR_SMPS8,
-	.iva.pmic		= &tps659038,
-};
-
-void hw_data_init(void)
-{
-	*prcm = &dra7xx_prcm;
-	*dplls_data = &dra7xx_dplls;
-	*omap_vcores = &cl_som_am57x_volts;
-	*ctrl = &dra7xx_ctrl;
-}
-
-void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
-{
-	switch (emif_nr) {
-	case 1:
-		*regs = &cl_som_am57x_emif1_ddr3_532mhz_emif_regs;
-		break;
-	case 2:
-		*regs = &cl_som_am57x_emif2_ddr3_532mhz_emif_regs;
-		break;
-	}
-}
-
-void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size)
-{
-	switch (emif_nr) {
-	case 1:
-		*regs = cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs;
-		*size = ARRAY_SIZE(cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs);
-		break;
-	case 2:
-		*regs = cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs;
-		*size = ARRAY_SIZE(cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs);
-		break;
-	}
-}
diff --git a/configs/cl-som-am57x_defconfig b/configs/cl-som-am57x_defconfig
deleted file mode 100644
index fd8353ede5..0000000000
--- a/configs/cl-som-am57x_defconfig
+++ /dev/null
@@ -1,64 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_OMAP54XX=y
-CONFIG_TARGET_CL_SOM_AM57X=y
-CONFIG_SPL=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_NR_DRAM_BANKS=2
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_VERSION_VARIABLE=y
-# CONFIG_SPL_FS_EXT4 is not set
-# CONFIG_SPL_NAND_SUPPORT is not set
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_PROMPT="U-Boot# "
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_EEPROM_LAYOUT=y
-CONFIG_EEPROM_LAYOUT_HELP_STRING="v2, v3"
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_SCSI_AHCI=y
-CONFIG_CMD_PCA953X=y
-CONFIG_LED_STATUS=y
-CONFIG_LED_STATUS_GPIO=y
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=37
-CONFIG_LED_STATUS_STATE=2
-CONFIG_MMC_OMAP_HS=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_SPEED=48000000
-CONFIG_SPI_FLASH_ATMEL=y
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_GIGADEVICE=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_MII=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_CONS_INDEX=3
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_TI_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_OMAP_USB_PHY=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_MCS7830=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/cl-som-am57x.h b/include/configs/cl-som-am57x.h
deleted file mode 100644
index bf2bb44d48..0000000000
--- a/include/configs/cl-som-am57x.h
+++ /dev/null
@@ -1,148 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Configuration settings for CompuLab CL-SOM-AM57x board
- *
- * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/
- *
- * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- */
-
-#ifndef __CONFIG_CL_SOM_AM57X_H
-#define __CONFIG_CL_SOM_AM57X_H
-
-#define CONSOLEDEV			"ttyO2"
-#define CONFIG_SYS_NS16550_COM3		UART3_BASE	/* UART3 */
-
-#define CONFIG_SYS_OMAP_ABE_SYSCK
-
-#define PARTS_DEFAULT
-
-#include <configs/ti_omap5_common.h>
-
-/* misc */
-#define CONFIG_REVISION_TAG
-
-/* PMIC I2C bus number */
-#define CONFIG_SYS_SPD_BUS_NUM 3
-
-/* SPI Flash support */
-#define CONFIG_TI_SPI_MMAP
-
-/* SPI SPL defines */
-/* Offsets: 0K - SPL1, 64K - SPL2, 128K - SPL3, 192K - SPL4, 256K - U-Boot */
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	(256 * 1024)
-#define CONFIG_SPL_SPI_SUPPORT
-
-/* SD/MMC RAW/FS boot */
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-
-/* Environment */
-#define CONFIG_ENV_SIZE			(16 << 10) /* 16 KiB env size */
-
-#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
-#define CONFIG_ENV_OFFSET		(768 * 1024)
-
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
-#define CONFIG_SYS_I2C_EEPROM_BUS       3
-
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
-#define CONFIG_SYS_EEPROM_SIZE		256
-
-#ifndef CONFIG_SPL_BUILD
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	1
-#define CONFIG_SYS_SCSI_MAX_LUN		1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-						CONFIG_SYS_SCSI_MAX_LUN)
-/* PCA9555 GPIO expander support */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR     0x20
-#define CONFIG_SYS_I2C_PCA953X_WIDTH    { {0x20, 16} }
-
-#endif /* !CONFIG_SPL_BUILD */
-
-/* USB xHCI HOST */
-#define CONFIG_USB_XHCI_OMAP
-
-#define CONFIG_OMAP_USB3PHY1_HOST
-
-/* USB Networking options */
-
-/* CPSW Ethernet */
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_PHY_ATHEROS
-#define CONFIG_SYS_RX_ETH_BUFFER	64
-#define PHY_ANEG_TIMEOUT		8000
-
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_NET_RETRY_COUNT		10
-
-/* Default environment */
-#undef CONFIG_EXTRA_ENV_SETTINGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	DEFAULT_LINUX_BOOT_ENV \
-	"autoload=no\0" \
-	"baudrate=115200\0" \
-	"console=ttyO2,115200n8\0" \
-	"bootdelay=3\0" \
-	"fdtfile=am57xx-sbc-am57x.dtb\0" \
-	"kernel=zImage-cl-som-am57x\0" \
-	"bootscr=bootscr.img\0" \
-	"displaytype=hdmi\0" \
-	"bootkernel=bootz ${loadaddr} - ${fdtaddr}\0" \
-	"mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
-	"mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
-	"emmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
-	"emmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
-	"load_mmc=mmc dev ${mmcdev} && mmc rescan && " \
-		"run mmcloadkernel && run mmcloadfdt\0" \
-	"mmcroot=/dev/mmcblk1p2\0" \
-	"mmcrootfstype=ext4 rw rootwait\0" \
-	"mmcargs=setenv bootargs console=${console} root=${mmcroot} " \
-		"rootfstype=${mmcrootfstype}\0" \
-	"mmcbootscript=setenv mmcdev 0; mmc dev ${mmcdev} && mmc rescan && " \
-		"load mmc ${mmcdev} ${loadaddr} ${bootscr} && " \
-		"echo Running bootscript from MMC/SD Card ... && " \
-		"source ${loadaddr}\0" \
-	"mmcboot=setenv mmcdev 0 && run load_mmc && " \
-		"run mmcargs && echo Booting from MMC/SD Card ... && " \
-		"run bootkernel\0" \
-	"emmcroot=/dev/mmcblk0p2\0" \
-	"emmcrootfstype=ext4 rw rootwait\0" \
-	"emmcargs=setenv bootargs console=${console} " \
-		"root=${emmcroot} " \
-		"rootfstype=${emmcrootfstype}\0" \
-	"emmcbootscript=setenv mmcdev 1; mmc dev ${mmcdev} && mmc rescan && " \
-		"load mmc ${mmcdev} ${loadaddr} ${bootscr} && " \
-		"echo Running bootscript from eMMC ... && " \
-		"source ${loadaddr}\0" \
-	"emmcboot=setenv mmcdev 1 && run load_mmc && " \
-		"run emmcargs && echo Booting from eMMC ... && " \
-		"run bootkernel\0" \
-	"sataroot=/dev/sda2\0" \
-	"satarootfstype=ext4 rw rootwait\0" \
-	"load_sata=load scsi 0 ${loadaddr} ${kernel} && " \
-		"load scsi 0 ${fdtaddr} ${fdtfile}\0" \
-	"sataargs=setenv bootargs console=${console} " \
-		"root=${sataroot} " \
-		"rootfstype=${satarootfstype}\0" \
-	"satabootscript=load scsi 0 ${loadaddr} ${bootscr} && " \
-		"echo Running bootscript from SATA ... && " \
-		"source ${loadaddr}\0" \
-	"sataboot=run load_sata && run sataargs && " \
-		"echo Booting from SATA ... && " \
-		"run bootkernel\0"
-
-#undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND \
-	"run mmcbootscript || run mmcboot || " \
-	"run satabootscript || run sataboot || " \
-	"run emmcbootscript || run emmcboot"
-
-
-#endif /* __CONFIG_CL_SOM_AM57X_H */