imx: Add PHYTEC phyBOARD-i.MX6UL-Segin

Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).

CPU:   Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   FEC0

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART (1 & 5)
 - USB (host & otg)

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>

12 files changed, 839 insertions, 1 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5c3225bcbfe..0e0bad9471a 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -459,7 +459,8 @@ dtb-$(CONFIG_MX6UL) += \
 	imx6ul-isiot-nand.dtb \
 	imx6ul-opos6uldev.dtb \
 	imx6ul-14x14-evk.dtb \
-	imx6ul-9x9-evk.dtb
+	imx6ul-9x9-evk.dtb \
+	imx6ul-phycore-segin.dtb
 
 dtb-$(CONFIG_MX6ULL) += imx6ull-14x14-evk.dtb
 
diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi b/arch/arm/dts/imx6ul-pcl063.dtsi
new file mode 100644
index 00000000000..24a6a479835
--- /dev/null
+++ b/arch/arm/dts/imx6ul-pcl063.dtsi
@@ -0,0 +1,173 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Collabora Ltd.
+ *
+ * Based on dts[i] from Phytec barebox port:
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+
+#include "imx6ul.dtsi"
+
+/ {
+	model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
+	compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	fsl,no-blockmark-swap;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0 0x400000>;
+	};
+
+	partition@400000 {
+		label = "uboot-env";
+		reg = <0x400000 0x100000>;
+	};
+
+	partition@500000 {
+		label = "root";
+		reg = <0x500000 0x0>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "cat,24c32";
+		reg = <0x52>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	bus-width = <0x4>;
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0X1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2cgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL       0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA       0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1grp_gpio {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX   0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX   0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+
+		>;
+	};
+};
diff --git a/arch/arm/dts/imx6ul-phycore-segin.dts b/arch/arm/dts/imx6ul-phycore-segin.dts
new file mode 100644
index 00000000000..a46012e2b44
--- /dev/null
+++ b/arch/arm/dts/imx6ul-phycore-segin.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Collabora Ltd.
+ *
+ * Based on dts[i] from Phytec barebox port:
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6ul-pcl063.dtsi"
+
+/ {
+	model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
+	compatible = "phytec,phyboard-imx6ul-segin", "phytec,imx6ul-pcl063",
+		     "fsl,imx6ul";
+};
+
+&i2c1 {
+	i2c_rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		status = "okay";
+	};
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID    0x17059
+		>;
+	};
+
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 3d56346ccb5..d0cee514a27 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -429,6 +429,18 @@ config TARGET_PFLA02
 	select MX6QDL
 	select SUPPORT_SPL
 
+config TARGET_PCL063
+	bool "PHYTEC PCL063 (phyCORE-i.MX6UL)"
+	select MX6UL
+	select DM
+	select DM_ETH
+	select DM_GPIO
+	select DM_I2C
+	select DM_MMC
+	select DM_SERIAL
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 config TARGET_SECOMX6
 	bool "secomx6 boards"
 
@@ -551,6 +563,7 @@ source "board/freescale/mx6ullevk/Kconfig"
 source "board/grinn/liteboard/Kconfig"
 source "board/phytec/pcm058/Kconfig"
 source "board/phytec/pfla02/Kconfig"
+source "board/phytec/pcl063/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/kosagi/novena/Kconfig"
 source "board/samtec/vining_2000/Kconfig"
diff --git a/board/phytec/pcl063/Kconfig b/board/phytec/pcl063/Kconfig
new file mode 100644
index 00000000000..977db70f641
--- /dev/null
+++ b/board/phytec/pcl063/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_PCL063
+
+config SYS_BOARD
+	default "pcl063"
+
+config SYS_VENDOR
+	default "phytec"
+
+config SYS_CONFIG_NAME
+	default "pcl063"
+
+endif
diff --git a/board/phytec/pcl063/MAINTAINERS b/board/phytec/pcl063/MAINTAINERS
new file mode 100644
index 00000000000..c65a951f3dd
--- /dev/null
+++ b/board/phytec/pcl063/MAINTAINERS
@@ -0,0 +1,8 @@
+PCL063 BOARD
+M:	Martyn Welch <martyn.welch@collabora.com>
+S:	Maintained
+F:	arch/arm/dts/imx6ul-pcl063.dtsi
+F:	arch/arm/dts/imx6ul-phycore-segin.dts
+F:	board/phytec/pcl063/
+F:	configs/phycore_pcl063_defconfig
+F:	include/configs/pcl063.h
diff --git a/board/phytec/pcl063/Makefile b/board/phytec/pcl063/Makefile
new file mode 100644
index 00000000000..53c73c9b082
--- /dev/null
+++ b/board/phytec/pcl063/Makefile
@@ -0,0 +1,7 @@
+# Copyright (C) 2018 Collabora Ltd.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := pcl063.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/phytec/pcl063/README b/board/phytec/pcl063/README
new file mode 100644
index 00000000000..be83bdb0d84
--- /dev/null
+++ b/board/phytec/pcl063/README
@@ -0,0 +1,26 @@
+How to use U-Boot on PHYTEC phyBOARD-i.MX6UL-Segin
+--------------------------------------------------
+
+- Configure and build U-Boot for phyCORE-i.MX6UL:
+
+    $ make mrproper
+    $ make phycore_pcl063_defconfig
+    $ make
+
+  This will generate SPL and u-boot-dtb.img images.
+
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Jumper settings:
+
+  JP1:   Open: Boot from NAND
+       Closed: Boot from SD/MMC1
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Insert the micro SD card in the board and power it up.
+
+- U-Boot messages should come up.
diff --git a/board/phytec/pcl063/pcl063.c b/board/phytec/pcl063/pcl063.c
new file mode 100644
index 00000000000..38b233d1b07
--- /dev/null
+++ b/board/phytec/pcl063/pcl063.c
@@ -0,0 +1,206 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Collabora Ltd.
+ *
+ * Based on board/ccv/xpress/xpress.c:
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE         | PAD_CTL_PUE       | \
+			PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+			PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | \
+			PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+	MX6_PAD_UART5_TX_DATA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART5_RX_DATA__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+#ifdef CONFIG_NAND_MXS
+
+#define NAND_PAD_CTRL (PAD_CTL_DSE_48ohm | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_48ohm | PAD_CTL_PUS_22K_UP)
+
+#define NANDREADYPC MUX_PAD_CTRL(NAND_PAD_READY0_CTRL)
+
+static iomux_v3_cfg_t const gpmi_pads[] = {
+	MX6_PAD_NAND_DATA00__RAWNAND_DATA00	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__RAWNAND_DATA01	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__RAWNAND_DATA02	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__RAWNAND_DATA03	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__RAWNAND_DATA04	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__RAWNAND_DATA05	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__RAWNAND_DATA06	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__RAWNAND_DATA07	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_CLE__RAWNAND_CLE		| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_ALE__RAWNAND_ALE		| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_RE_B__RAWNAND_RE_B		| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__RAWNAND_WE_B		| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NAND_READY_B__RAWNAND_READY_B	| NANDREADYPC,
+};
+
+static void setup_gpmi_nand(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	setup_gpmi_io_clk((3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
+			  (3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
+}
+
+#endif /* CONFIG_NAND_MXS */
+
+#ifdef CONFIG_FEC_MXC
+
+#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE       | \
+			   PAD_CTL_SPEED_HIGH  | PAD_CTL_DSE_48ohm | \
+			   PAD_CTL_SRE_FAST)
+
+#define MDIO_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE      | \
+			   PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | \
+			   PAD_CTL_ODE)
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+	imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	/*
+	 * Use 50M anatop loopback REF_CLK1 for ENET1,
+	 * clear gpr1[13], set gpr1[17].
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	/*
+	 * Use 50M anatop loopback REF_CLK2 for ENET2,
+	 * clear gpr1[14], set gpr1[18].
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(1, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/*
+	 * Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
+	 * 50 MHz RMII clock mode.
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif /* CONFIG_FEC_MXC */
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_fec();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: PHYTEC phyCORE-i.MX6UL\n");
+
+	return 0;
+}
diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
new file mode 100644
index 00000000000..b93cd493f21
--- /dev/null
+++ b/board/phytec/pcl063/spl.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Collabora Ltd.
+ *
+ * Based on board/ccv/xpress/spl.c:
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <fsl_esdhc.h>
+
+/* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8 -> 256MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x41480148,
+	.p0_mprddlctl = 0x40403E42,
+	.p0_mpwrdlctl = 0x40405852,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,		/* Bus size = 16bit */
+	.cs_density = 18,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 1,
+	.rtt_nom = 1,
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.pd_fast_exit = 1,
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+	.refsel = 1,		/* Refresh cycles at 32KHz */
+	.refr = 7,		/* 8 refresh commands per refresh cycle */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 933,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 1,
+	.trcd = 1391,
+	.trcmin = 4791,
+	.trasmin = 3400,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE         | PAD_CTL_PUE       | \
+			PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW | \
+			PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | \
+			PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{
+		.esdhc_base = USDHC1_BASE_ADDR,
+		.max_bus_width = 4,
+	},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+#endif /* CONFIG_FSL_ESDHC */
+
+void board_init_f(ulong dummy)
+{
+	ccgr_init();
+
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* Setup iomux and fec */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+}
diff --git a/configs/phycore_pcl063_defconfig b/configs/phycore_pcl063_defconfig
new file mode 100644
index 00000000000..02c659de238
--- /dev/null
+++ b/configs/phycore_pcl063_defconfig
@@ -0,0 +1,62 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_PCL063=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_USB_GADGET_SUPPORT=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
+CONFIG_MTDPARTS_DEFAULT="gpmi-nand:4m(uboot),1m(env),-(root)"
+CONFIG_CMD_UBI=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ul-phycore-segin"
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_MTD=y
+CONFIG_NAND=y
+CONFIG_NAND_MXS=y
+CONFIG_NAND_MXS_DT=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Phytec"
+CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
diff --git a/include/configs/pcl063.h b/include/configs/pcl063.h
new file mode 100644
index 00000000000..4ceab519cbc
--- /dev/null
+++ b/include/configs/pcl063.h
@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Collabora Ltd.
+ *
+ * Based on include/configs/xpress.h:
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ */
+#ifndef __PCL063_H
+#define __PCL063_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+/*
+ * There is a bug in some i.MX6UL processors that results in the initial
+ * portion of OCRAM being unavailable when booting from (at least) an SD
+ * card.
+ *
+ * Tweak the SPL text base address to avoid this.
+ */
+#undef CONFIG_SPL_TEXT_BASE
+#define CONFIG_SPL_TEXT_BASE            0x00909000
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC1_BASE_ADDR
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			SZ_256M
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_ENV_SIZE			(16 << 10)
+#define CONFIG_ENV_OFFSET		(512 << 10)
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	1
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=ttymxc0,115200n8\0" \
+	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+	"fdt_addr_r=0x82000000\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"kernel_addr_r=0x81000000\0" \
+	"pxefile_addr_r=0x87100000\0" \
+	"ramdisk_addr_r=0x82100000\0" \
+	"scriptaddr=0x87000000\0" \
+	BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(UBIFS, ubifs, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#endif /* __PCL063_H */