summaryrefslogtreecommitdiff
path: root/drivers/regulator
AgeCommit message (Collapse)Author
2011-01-14regulator: Support MAX8998/LP3974 DVS-GPIOMyungJoo Ham
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and BUCK2-DVS2 modes. This patch adds such modes and an option to block setting buck1/2 voltages out of the preset values. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-01-14mfd: Support LP3974 RTCMyungJoo Ham
The first releases of LP3974 have a large delay in RTC registers, which requires 2 seconds of delay after writing to a rtc register (recommended by National Semiconductor's engineers) before reading it. If "rtc_delay" field of the platform data is true, the rtc driver assumes that such delays are required. Although we have not seen LP3974s without requiring such delays, we assume that such LP3974s will be released soon (or they have done so already) and they are supported by "lp3974" without setting "rtc_delay" at the platform data. This patch adds delays with msleep when writing values to RTC registers if the platform data has rtc_delay set. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-01-13Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (348 commits) ALSA: hda - Fix NULL-derefence with a single mic in STAC auto-mic detection ALSA: hda - Add missing NID 0x19 fixup for Sony VAIO ALSA: hda - Fix ALC275 enable hardware EQ for SONY VAIO ALSA: oxygen: fix Xonar DG input ALSA: hda - Fix EAPD on Lenovo NB ALC269 to low ALSA: hda - Fix missing EAPD for Acer 4930G ALSA: hda: Disable 4/6 channels on some NVIDIA GPUs. ALSA: hda - Add static_hdmi_pcm option to HDMI codec parser ALSA: hda - Don't refer ELD when unplugged ASoC: tpa6130a2: Fix compiler warning ASoC: tlv320dac33: Add DAPM selection for LOM invert ASoC: DMIC codec: Adding a generic DMIC codec ALSA: snd-usb-us122l: Fix missing NULL checks ALSA: snd-usb-us122l: Fix MIDI output ASoC: soc-cache: Fix invalid memory access during snd_soc_lzo_cache_sync() ASoC: Fix section mismatch in wm8995.c ALSA: oxygen: add S/PDIF source selection for Claro cards ALSA: oxygen: fix CD/MIDI for X-Meridian (2G) ASoC: fix migor audio build ALSA: include delay.h for msleep in Xonar DG support ...
2011-01-13Merge branch 'topic/asoc' into for-linusTakashi Iwai
2011-01-12regulator: missing index in PTR_ERR() in isl6271a_probe()roel kluin
The index is missing so the return is wrong. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Assign return value of mc13xxx_reg_rmw to retAxel Lin
Otherwise, we will not return error if write to MC13892_SWITCHERS5 failed. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Yong Shen <yong.shen@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Add initial per-regulator debugfs supportMark Brown
We only expose the use and open counts to userspace, providing a tiny bit of insight into what the API is up to. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Make regulator_has_full_constraints a boolMark Brown
It's a boolean value so use the type. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Clean up logging a bitMark Brown
The recent introduction of standard regulator API logging macros means that all our log messages have at least the function name in them and logging that the constraints are for the regulator API is probably a bit much. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Optimise out noop voltage changesMark Brown
If a consumer sets the same voltage range as is currently configured for that consumer there's no need to run through setting the voltage again. This pattern may occur with some CPUfreq implementations where the same voltage range is used for multiple frequencies. Reported-by: Saravana Kannan <skannan@codeaurora.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Add API to re-apply voltage to hardwareMark Brown
When cooperating with an external control source the regulator setup may be changed underneath the API. Currently consumers can just redo the regulator_set_voltage() to restore a previously set configuration but provide an explicit API for doing this as optimsations in the regulator_set_voltage() implementation will shortly prevent that. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Staticise non-exported functions in mc13892Mark Brown
No point exposing functions that aren't used elsewhere to the global namespace and sparse warns about doing so. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Only notify voltage changes when they succeedMark Brown
Currently we notify a voltage change whenever we exit set_voltage(), even if the change failed for some reason (eg, a constraints issue). This shouldn't cause any substantial ill effects but is wasteful as listeners get notified on noops. Fix this by moving the notification into _do_set_voltage() and only notifying if we don't return an error. Reported-by: Saravana Kannan <skannan@codeaurora.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Provide a selector based set_voltage_sel() operationMark Brown
Many regulator drivers implement voltage setting by looping through a table of possible values, normally because the set of available voltages can't be mapped onto selectors with simple calcuation. Factor out these loops by providing a variant of set_voltage() which takes a selector rather than a voltage range as an argument and implementing a loop through the available selectors in the core. This is not going to be suitable for use with all devices as when the regulator voltage can be mapped onto selector values with a simple calculation the linear scan through the available values will be more expensive than just doing the calculation, especially for regulators that provide fine grained voltage control. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Factor out voltage set operation into a separate functionMark Brown
Push all the callers of the chip set_voltage() operation out into a single function to facilitiate future refactoring. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Convert WM8994 to use get_voltage_sel()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Convert WM835x to use get_voltage_sel()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Allow modular build of mc13xxx-coreMark Brown
Since the MFD core for this device and the regulator drivers for these devices can be built modular we should also support modular build of the shared code for the regulator drivers, otherwise we try to link built in code against modular code with unfortunate results. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: support PMIC mc13892Yong Shen
add support for mc13892, tested on mx51 babbage board Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Yong Shen <yong.shen@linaro.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12make mc13783 regulator code genericYong Shen
move some common functions and micros of mc13783 regulaor driver to a seperate file, which makes it possible for mc13892 to share code. Signed-off-by: Yong Shen <yong.shen@linaro.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12Change the register name definitions for mc13783Yong Shen
To make mc13783 and mc13892 share code, the register names should be changed to fit the new macro definitions in the comming patch. Signed-off-by: Yong Shen <yong.shen@linaro.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Removed macros for initialization of ab8500 regulatorsBengt Jonsson
This patch removes the macros for initializing the regulators. The purpose is to remove one layer of abstraction and make the code easier to read. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Added verbose debug messages to ab8500 regulatorsBengt Jonsson
The verbose debug outputs register writes and reads that can be used to debug the driver. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Modified ab8500 error handlingBengt Jonsson
Error handling is updated to catch NULL pointer errors. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Updated ab8500 variable names, macro names and commentsBengt Jonsson
The regulator enumeration is used for putting the regulator data in correct place in the info array. This should be matched in the board configuration. Variable names are updated to be more consistent, comments are corrected and macros have been edited to be consistent. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Added ab8500 v2 supportBengt Jonsson
The AUX3 regulator voltage setting is changed in ab8500 v2 compared to ab8500 v1. This patch adds v2 support while keeping support for v1. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Clean out unused code in ab8500 regulatorsBengt Jonsson
The find_regulator function was unused so it has been removed. The ab8500 pointer in the regulator info structure was unused and so it has also been removed. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Fixed errors in ab8500 register mappingBengt Jonsson
For INTCORE and TVOUT regulators, the low power register bit is included in the mask so that enable will set the regulator in normal (high power) mode. ANAMIC1, ANAMIC2, DMIC regulator settings are swapped with each other so that the correct regulator gets enabled/disabled. ANA regulator register address is corrected. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulators: Moved define for number of regulators in ab8500Bengt Jonsson
The define for number of regulators is moved from ab8500-core to ab8500-regulator so that the regulator driver can be updated independently of ab8500-core. This also changes the platform configuration structure of ab8500-core so that it contains a pointer to the regulator_init_data array plus number of regulators instead of an fixed size array of pointers to regulator_init_data. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: add driver for tps6524x regulatorCyril Chemparathy
TPS6524X provides three step-down converters and two general-purpose LDO voltage regulators. This device is interfaced using SPI. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Convert WM831x drivers to use get_voltage_sel()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Allow drivers to report voltages as selectorsMark Brown
Since drivers already have to provide an API for translating selectors into voltages they may as well just report the selector values directly to the core API rather than implement the lookup themselves. The old interface is left in place for now, but may be removed in future. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Use _regulator_get_voltage() consistentlyMark Brown
Rather than referencing the get_voltage() operation directly in the ops struct use the internal _regulator_get_voltage() API call to do so, facilitating refactoring. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12drivers/regulator: Update WARN usesJoe Perches
Align arguments. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Take into account the requirements of all consumersThomas Petazzoni
Extend the regulator_set_voltage() function to take into account the voltage requirements of all consumers of the regulator being changed, in order to set the voltage to the minimum voltage acceptable to all consumers. The existing behaviour was that the latest regulator_set_voltage() call would win over previous regulator_set_voltage() calls even if setting the voltage to a non-acceptable level from other consumers. Signed-off-by: Thomas Petazzoni <t-petazzoni@ti.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Add and use rdev_<level> macrosJoe Perches
On Tue, 2010-11-30 at 10:52 +0000, Mark Brown wrote: > On Mon, Nov 29, 2010 at 05:12:56PM -0800, Joe Perches wrote: > > Just to please broonie... > > Signed-off-by: Joe Perches <joe@perches.com> > As usual when fixing review issues please revise your original patch > rather than posting a fresh patch. Here's an earlier comment: On Thu, 2010-11-18 at 13:30 +0000, Mark Brown wrote: > This looks reasonable, please rebase on top of Daniel's patches and > submit it properly (with changelog and so on). Sometimes it's simpler for an upstream maintainer to do something like: git am -s <patch1.mbox> patch -p1 < patch2.mbox git commit --amend file instead of back and forthing. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Remove duplicate consts from mc13873 driver voltage tablesMark Brown
They're not needed and sparse is verbosely upset about them. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Copy constraints from regulators when initialising themMark Brown
Currently the regulator API uses the constraints structure passed in to the core throughout the lifetime of the object. This means that it is not possible to mark the constraints as __initdata so if the kernel supports many boards the constraints for all of them are kept around throughout the lifetime of the system, consuming memory needlessly. By copying constraints that are actually used we allow the use of __initdata, saving memory when multiple boards are supported. This also means the constraints can be const. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Fix prototype for MAX8998 buck set_voltage()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Remove regulator core version announcementMark Brown
The version hasn't been updated since the regulator API was merged in 2.6.27 so just remove it - now we're in mainline the kernel version is much more useful. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Fix obfuscated log messagesMark Brown
Don't use %s to format fixed static strings into log messages, it just makes searching for and reading the message in the kernel source needlessly hard. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12drivers: regulator: core: convert to using pr_ macrosDaniel Walker
The regulator framework uses a lot of printks with a specific formatting using __func__. This converts them to use pr_ calls with a central format string. Cc: bleong@codeaurora.org Signed-off-by: Daniel Walker <dwalker@codeaurora.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12drivers: regulator: core: use pr_fmtDaniel Walker
This adds a pr_fmt line which uses the __func__ macro. I also convert the current pr_ lines to remove their __func__ usage. Cc: bleong@codeaurora.org Signed-off-by: Daniel Walker <dwalker@codeaurora.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Fix typo in PCAP regulator_set_voltage()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: enable supply regulator only when use count is zeroBengt Jonsson
Supply regulators are disabled only when the last reference count is removed on the child regulator (the use count goes from 1 to 0). This patch changes the behaviour of enable so the supply regulator is enabled only when the use count of the child regulator goes from 0 to 1. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Add basic trace facilitiesMark Brown
Provide some basic trace facilities to the regulator API. We generate events on regulator enable, disable and voltage setting over the actual hardware operations (which are assumed to be the expensive ones which require interaction with the actual device). This is intended to facilitate debug of the performance and behaviour with consumers allowing unified traces to be generated including the regulator operations within the context of the other components of the system. For enable we log the explicit delay for the voltage ramp separately to the interaction with the hardware to highlight the time consumed in I/O. We should add a similar delay for voltage changes, though there the relatively small magnitude of the changes in the context of the I/O costs makes it much less critical for most regulators. Only hardware interactions are currently traced as the primary focus is on the performance and synchronisation of actual hardware interactions. Additional tracepoints for debugging of the logical operations can be added later if required. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: Report actual configured voltage to set_voltage()Mark Brown
Change the interface used by set_voltage() to report the selected value to the regulator core in terms of a selector used by list_voltage(). This allows the regulator core to know the voltage that was chosen without having to do an explict get_voltage(), which would be much more expensive as it will generally access hardware. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12regulator: lock supply in regulator enableMattias Wallin
This patch add locks around regulator supply enable. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-13regulator: Update LDO2 for WM8958Mark Brown
LDO2 has a slightly different range of supported voltages on WM8958 so update the selector<->voltage mappings to match. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-09regulator: tps6586x: correct register tableDanny Huang
Correct the register table for SM2, LDO8, RTC Change-Id: I45348cec5ffbb7da9bd7523764fb611b537236b8 Signed-off-by: Danny Huang <dahuang@nvidia.com> Signed-off-by: Olof Johansson <olofj@chromium.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>