| Age | Commit message (Collapse) | Author |
|---|
|
Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.
This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:
* With certain SD cards timeouts like the following have been seen
due to an improper calculation of the dto value:
mmcblk0: error -110 transferring data, sector 4126233, nr 8,
card status 0xc00
* By removing the dto calculation and setting the timeout value
to the maximum specified by the SD card specification part A2
section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
relevant ones are:
* http://talk.maemo.org/showthread.php?p=1000707#post1000707
* http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch fixes a compile error in drivers/mmc/host/sdhci-dove.c
by including the linux/module.h file.
Signed-off-by: Alf Høgemark <alf@i100.no>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This reverts commit e6039832bed9a9b967796d7021f17f25b625b616.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This reverts commit c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.
According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.
Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
OMAP4 and OMAP3 HSMMC IP registers differ by 0x100 offset.
Adding the offset to platform_device resource structure
increments the start address for every insmod operation.
MMC command fails on re-insertion as module due to incorrect register
base. Fix this by updating the ioremap base address only.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This will delete some boilerplate code, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If we put probe() on __init section, that will never work for multiple
module insertions/removals.
In order to make it work properly, move probe to __devinit section and
use platform_driver_register() instead of platform_driver_probe().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
A bunch of non-functional cleanups to the omap_hsmmc driver.
It basically decreases indentation level, drop unneded dereferences
and drop unneded accesses to the platform_device structure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Call context save api after enabling runtime pm to make sure that
register access in context save api happens with clk enabled.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
pm_runtime_put_sync instead of autosuspend pm runtime API
because iounmap(host->base) follows immediately.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Neil Brown reports that commit 35cd133c
PM: Run the driver callback directly if the subsystem one is not there
breaks suspend for his libertas wifi, because SDIO has a protocol
where the suspend method can return -ENOSYS and this means "There is
no point in suspending, just turn me off". Moreover, the suspend
methods provided by SDIO drivers are not supposed to be called by
the PM core or bus-level suspend routines (which aren't presend for
SDIO). Instead, when the SDIO core gets to suspend the device's
ancestor, it calls the device driver's suspend function, catches the
ENOSYS, and turns the device off.
The commit above breaks the SDIO core's assumption that the device
drivers' callbacks won't be executed if it doesn't provide any
bus-level callbacks. If fact, however, this assumption has never
been really satisfied, because device class or device type suspend
might very well use the driver's callback even without that commit.
The simplest way to address this problem is to make the SDIO core
tell the PM core to ignore driver callbacks, for example by providing
no-operation suspend/resume callbacks at the bus level for it,
which is implemented by this change.
Reported-and-tested-by: Neil Brown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
[stable: please apply to 3.3-stable only]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When UHS-I card is detected also print the bus speed mode in which
UHS-I card will be running.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
MSI on my O2Micro OZ600 SD card reader is broken. This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There is no need to tune mmc->f_min to a value near 400kHz as the MMC core
begins testing frequencies at 400kHz regardless of the value of mmc->f_min.
As suggested by Guennadi Liakhovetski.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc->f_max should be half of the bus clock.
And now that mmc->f_max is not equal to the bus clock the
latter should be used directly to calculate mmc->f_min.
Cc: Magnus Damm <magnus.damm@gmail.com>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Correct an off-by one error when calculating the clock divisor in cases
where the host clock is a power of two of the target clock. Previously the
divisor was one greater than the correct value in these cases leading to
the clock being set at half the desired speed.
Thanks to Guennadi Liakhovetski for working with me on the logic for this
change.
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since most of the work is already done by the core we just need to add
runtime suspend methods and tell the PM core that runtime PM is enabled
for this device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This matches current best practice as one can have runtime PM enabled
without system sleep and CONFIG_PM is defined for both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
The call to platform_get_resource was moved just to make it closer to the
place where its result it used.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the sdhci-s3c driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
max_width member in platform data can be used to derive the mmc bus transfer
width that can be supported by the controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI controllers on Exynos4 do not include the sdclk divider as per the
sdhci controller specification. This case can be represented using the
sdhci quirk SDHCI_QUIRK_NONSTANDARD_CLOCK instead of using an additional
enum type definition 'clk_types'.
Hence, usage of clk_type member in platform data is removed and the sdhci
quirk is used. In addition to that, since this qurik is SoC specific,
driver data is introduced to represent controllers on SoC's that require
this quirk.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
|
|
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
|
|
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
|
|
Currently if a platform wants to implement a non-standard card-detection
method, it would need to call tmio_mmc_cd_wakeup(), which is an inline
function, calling mmc_detect_change(). For this the platform would have
to link mmc_core statically into the kernel, losing the ability to build
it as a module. This patch adds a callback to the sh_mobile_sdhi driver,
which eliminates this dependency.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some boards need a preliminary setup stage to prepare the sdhi
controller.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On sh-mobile platforms the MMC clock frequency for the TMIO MMC unit is
obtained from the same clock, as the one, that runtime power-manages the
controller. The SDHI glue code has to access that clock directly,
bypassing the runtime PM framework, to get its frequency, but it
shouldn't enable or disable it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The sdio_irq_enabled member of struct tmio_mmc_host is a left-over from the
previously removed SDIO IRQ workaround. It is no longer needed and can now
be removed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The controller power status flag does not have to be accessed from the
hot-plug detection code any more, it can now be removed from the platform
data and put in the controller private struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
To use TMIO MMC driver ability to interface to the generic MMC GPIO card
hotplug detection helper, the SDHI driver has to pass the GPIO number
from its own platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If the platform specifies the TMIO_MMC_HAS_COLD_CD flag, use the generic
MMC GPIO card hotplug helper.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The condition, whether we have to use the native TMIO card hotplug
detection interrupt, is rather complex, it is better to only calculate it
once and store in the private data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Calculate the IRQ number, using gpio_to_irq() and use fixed flags: trigger
on both edges. This makes two out of four arguments of the
mmc_cd_gpio_request() function redundant.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When using MSI it is possible that a new MSI is sent while an earlier
MSI is currently handled. In this case SDHCI_INT_STATUS only contains
SDHCI_INT_RESPONSE and the ISR would not be called again. But at the end
of the ISR SDHCI_INT_DATA_END is now also pending which would be ignored.
Fix this by rereading the interrupt flags in the ISR until no interrupt
we care is pending.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Someone could use send_hpi_cmd() on a card that doesn't advertise support
for HPI. Then maybe didn't work fine. Because card->ext_csd.hpi_cmd
didn't set. So if card didn't support hpi, return the warning message.
And CMD12's flags is MMC_RSP_R1B.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For small size non-dma sdio transactions, it is sometimes better to poll
the mmc host and avoid interrupts altogether. Polling lowers the number
of interrupts and context switches. Tests have shown that for small
transactions, only a few polling iterations are needed, so this is worth
while.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
