| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit acc13958c2b2623c17e2450b8cd6881b698756d3 ]
In case of error condition to avoid system crash Tegra SDMMC controller
requires CMD and DAT resets issued together. SDHCI controller FSM goes
into bad state due to rapid SD card hot-plug event. Issuing reset on the
CMD FSM before DATA FSM results in kernel panic, hence add support to
issue CMD and DAT resets together.
This is applicable to Tegra186 and later chips.
Signed-off-by: Aniruddha TVS Rao <anrao@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221206165945.3551774-7-thierry.reding@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Commit 20b92a30b561 ("mmc: sdhci: update signal voltage switch code")
removed voltage switch delays from sdhci because mmc core had been
enhanced to support them. However that assumed that sdhci_set_ios()
did a single clock change, which it did not, and so the delays in mmc
core, which should have come after the first clock change, were not
effective.
Fix by avoiding re-configuring UHS and preset settings when the clock
is turning on and the settings have not changed. That then also avoids
the associated clock changes, so that then sdhci_set_ios() does a single
clock change when voltage switching, and the mmc core delays become
effective.
To do that has meant keeping track of driver strength (host->drv_type),
and cases of reinitialization (host->reinit_uhs).
Note also, the 'turning_on_clk' restriction should not be necessary
but is done to minimize the impact of the change on stable kernels.
Fixes: 20b92a30b561 ("mmc: sdhci: update signal voltage switch code")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221128133259.38305-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS is used by only ENE controllers but can
be replaced by driver code.
Amend the ENE code to hook the ->set_ios() mmc host operation and do the
reset there.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20220926192022.85660-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-3-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The block layer forces a minimum segment size of PAGE_SIZE, so a segment
can be too big for the ADMA table, if PAGE_SIZE >= 64KiB. Fix by writing
multiple descriptors, noting that the ADMA table is sized for 4KiB chunks
anyway, so it will be big enough.
Reported-and-tested-by: Bough Chen <haibo.chen@nxp.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211115082345.802238-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_card_detect() is not defined anywhere. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The analogue of the sdhci_get_cd_nogpio() is used in the sdhci-pci-core
and sdhci-acpi modules. Deduplicate it by moving to sdhci and exporting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Introduce max_timeout_count variable in the sdhci_host structure
and use in timeout calculation. By default its set to 0xE
(max timeout register value as per SDHC spec). But at the same time
vendors drivers can update it if they support different max timeout
register value than 0xE.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-2-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for the legacy Arasan sdhci controller on the BCM7211 and
related SoC's. This includes adding a .shutdown callback to increase
the power savings during S5.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210602192758.38735-2-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If vendor platform drivers are controlling whole logic of voltage
switching, then sdhci driver no need control vqmmc regulator.
So skip enabling/disable vqmmc from SDHC driver.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Introduce new sdhci ops to dump vendor specific registers in the
sdhci_dumpregs during error.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-8-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some controller as the ColdFire eshdc may require an endianness
byte swap, because DMA read endianness is not configurable.
Facilitate using the bounce buffer for this by adding
->copy_to_bounce_buffer().
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-2-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200511062828.1791484-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Implement the request_atomic() ops for the sdhci driver to process
one request in the atomic context if the card is nonremovable.
Moreover, we should return BUSY flag if controller has not released
the inhibit bits to allow HSQ trying to send request again in non-atomic
context.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/9ed34afa9fb42e0c234065cac5401d7826942b55.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_send_command() has not been used outside of sdhci.c for many
years. Stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-2-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use the FIELD_GET macro to get access to the register fields.
Delete the shift macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200312110050.21732-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some controllers diverge from the standard way of setting power and need
their bus voltage register to be configured regardless of the whether
they use regulators. As this is a common pattern across sdhci hosts,
create a helper function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-2-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200226223125.GA20630@embeddedor
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When using the host software queue, it will trigger the next request in
irq handler without a context switch. But the sdhci_request() can not be
called in interrupt context when using host software queue for some host
drivers, due to the get_cd() ops can be sleepable.
But for some host drivers, such as Spreadtrum host driver, the card is
nonremovable, so the get_cd() ops is not sleepable, which means we can
complete the data request and trigger the next request in irq handler
to remove the context switch for the Spreadtrum host driver.
As suggested by Adrian, we should introduce a request_atomic() API to
indicate that a request can be called in interrupt context to remove
the context switch when using mmc host software queue. But this should
be done in another thread to convert the users of mmc host software queue.
Thus we can introduce a variable in struct sdhci_host to indicate that
we will always to defer to complete requests when using the host software
queue.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/e693e7a29beb3c1922b333f4603ea81f43d5c5b1.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add request_done ops for struct sdhci_ops as a preparation in case some
host controllers have different method to complete one request, such as
supporting request completion of MMC software queue.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/1539c801c8bbdbcd1d86f8c2dab375f5803c765a.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Let a vendor driver supply the maximum descriptor size that it
can operate on. ADMA descriptor table would be allocated using this
supplied size.
If any SD Host controller is of version prior to v4.10 spec
but supports 16byte descriptor, this change allows them to supply
correct descriptor size for ADMA table allocation.
Also let a vendor driver update the descriptor size by overriding
sdhc_host->desc_size if it has to operates on a different descriptor
sizes in different conditions.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Refactor sdhci_set_timeout() such that platform drivers can do some
functionality in a set_timeout() callback and then call
__sdhci_set_timeout() to complete the operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Export sdhci_set_timeout_irq() so that it is accessible from platform drivers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some standard SD host controllers can support both external dma
controllers as well as ADMA/SDMA in which the SD host controller
acts as DMA master. TI's omap controller is the case as an example.
Currently the generic SDHCI code supports ADMA/SDMA integrated in
the host controller but does not have any support for external DMA
controllers implemented using dmaengine, meaning that custom code is
needed for any systems that use an external DMA controller with SDHCI.
Fixes by Faiz Abbas <faiz_abbas@ti.com>:
1. Map scatterlists before dmaengine_prep_slave_sg()
2. Use dma_async() functions inside of the send_command() path and call
terminate_sync() in non-atomic context in case of an error.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda230f ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add host operation ->set_dma_mask() so that drivers can define their own
DMA masks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
__sdhci_read_caps() does not modify *ver, *caps, or *caps1.
Probably, the caller of this function will want to constifythe
parameters passed in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Export sdhci_abort_tuning() function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The GL9750 and GL9755 chipsets, and possibly others, require PLL Enable
setup as part of the internal clock setup as described in 3.2.1 Internal
Clock Setup Sequence of SD Host Controller Simplified Specification
Version 4.20.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.
In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".
However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove whitespace in front of SDHCI_CTRL_8BITBUS. The value is not part
of SDHCI_CTRL_DMA_MASK.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove finish_tasklet. Requests that require DMA-unmapping or sdhci_reset
are completed either in the IRQ thread or a workqueue if the completion is
not initiated by the IRQ.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As per the Host Controller Standard Specification Version 4.20,
limitation of tuning iteration count is removed as PLL locking
time can be longer than UHS-1 tuning due to larger PVT fluctuation
and it will result in increase of tuning iteration to complete the
tuning.
This patch creates sdhci_host member tuning_loop_count to allow
hosts to specify maximum tuning iterations and also updates
execute_tuning to use this specified maximum tuning iteration count.
Default tuning_loop_count is set to same as existing loop count of
MAX_TUNING_LOOP which is 40 iterations.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Below are the supported DMA types in Host Control1 Register
with Version 4 enable
b'00 - SDMA
b'01 - Not Used
b'10 - ADMA2
b'11 - ADMA2 or ADMA3
ADMA3 uses Command Descriptor to issue an SD command.
A multi-block data transfer is performed by using a pair of CMD
descriptor and ADMA2 descriptor.
ADMA3 performs multiple of multi-block data transfer by using
Integrated Descriptor which is more suitable for Command Queuing
to fetch both Command and Transfer descriptors.
Host Capabilities register indicates the supports of ADMA3 DMA.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
1. O2 Host Controller PLL lock status is not in compliance with
CLOCK_CONTROL register bit 1
2. O2 Host Controller card detect function only work when PLL is
enabled and locked
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Host controllers may not have a LED signal line, whereas the register
updates to control the non-existent LED can be relatively time consuming.
Add a quirk to disable LED control.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.
This patch add this new mode support.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.
Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.
For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode. This patch introduced an interface to enable
v4 mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Added definitions for v400, v410, v420.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
