Age | Commit message (Collapse) | Author |
|
Buffers were being left in active state when streams were stopped
which resulted in memory leaks and failures when restarting pipelines.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
|
|
h265 decoder performance has been significantly worse than h264 decoder
due to latency in gstreamer format negotiation. Remove this latency by
aligning the pixel resolution earlier.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-5.10.y-cicd
This is the 5.10.165 stable release
* tag 'v5.10.165' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (951 commits)
Linux 5.10.165
io_uring/rw: remove leftover debug statement
io_uring/rw: ensure kiocb_end_write() is always called
io_uring: fix double poll leak on repolling
io_uring: Clean up a false-positive warning from GCC 9.3.0
mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
Bluetooth: hci_qca: Fixed issue during suspend
Bluetooth: hci_qca: check for SSR triggered flag while suspend
Bluetooth: hci_qca: Wait for SSR completion during suspend
soc: qcom: apr: Make qcom,protection-domain optional again
Revert "wifi: mac80211: fix memory leak in ieee80211_if_add()"
net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
net/ulp: use consistent error code when blocking ULP
io_uring/net: fix fast_iov assignment in io_setup_async_msg()
io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
tracing: Use alignof__(struct {type b;}) instead of offsetof()
x86/fpu: Use _Alignof to avoid undefined behavior in TYPE_ALIGN
Revert "drm/amdgpu: make display pinning more flexible (v2)"
efi: rt-wrapper: Add missing include
arm64: efi: Execute runtime services from a dedicated stack
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
# Conflicts:
# net/hsr/hsr_device.c
# net/hsr/hsr_forward.c
|
|
On system suspend, terminate any active DMA transfers and signal subdev
(cadence bridge) to stop streaming. Restore back the subdev and restart
DMA transfer on resume, using the same buffer (if any) as before.
Also refactor code to restart DMA into a common function.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable basic power management hooks for the CSI-RX wrapper IP.
System can be put through multiple suspend-resume cycles, and new
capture can be started after resuming.
Active usecase is not yet supported, thus in-progress streams will not
be resumed on system wake up.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Use runtime power management hooks to save power when CSI-RX is not in
use. Also stop/start any in-progress streams, which might happen during
a system suspend/resume cycle.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Co-authored-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-5.10.y-cicd
This is the 5.10.162 stable release
* tag 'v5.10.162' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (198 commits)
Linux 5.10.162
io_uring: pass in EPOLL_URING_WAKE for eventfd signaling and wakeups
eventfd: provide a eventfd_signal_mask() helper
eventpoll: add EPOLL_URING_WAKE poll wakeup flag
Revert "proc: don't allow async path resolution of /proc/self components"
Revert "proc: don't allow async path resolution of /proc/thread-self components"
net: remove cmsg restriction from io_uring based send/recvmsg calls
task_work: unconditionally run task_work from get_signal()
signal: kill JOBCTL_TASK_WORK
io_uring: import 5.15-stable io_uring
task_work: add helper for more targeted task_work canceling
kernel: don't call do_exit() for PF_IO_WORKER threads
kernel: stop masking signals in create_io_thread()
x86/process: setup io_threads more like normal user space threads
arch: ensure parisc/powerpc handle PF_IO_WORKER in copy_thread()
arch: setup PF_IO_WORKER threads like PF_KTHREAD
entry/kvm: Exit to user mode when TIF_NOTIFY_SIGNAL is set
kernel: allow fork with TIF_NOTIFY_SIGNAL pending
coredump: Limit what can interrupt coredumps
kernel: remove checking for TIF_NOTIFY_SIGNAL
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Only four discrete framerates(15/1, 30/1, 45/1, 60/1) were supported. With
this patch, continuous range of framerates with step of 1 are enabled.
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Tested-by: Brandon Brnich <b-brnich@ti.com>
|
|
Gain control is badly documented in publicly available (including
leaked) documentation.
There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value
(plus an enable bit in bit 6). The driver hardcodes it to 0x43, which
one application note states is equal to x1.047. The documentation also
states that 0x40 is equel to x1.000. The pre-gain thus seems to be
expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984.
What the pre-gain does is however unspecified.
There is then an AGC gain limit, in registers 0x3a18 and 0x3a19,
expressed as a 10-bit "real gain format" value. One application note
sets it to 0x00f8 and states it is equal to x15.5, so it appears to be
expressed in 1/16 increments, up to x63.9375.
The manual gain is stored in registers 0x350a and 0x350b, also as a
10-bit "real gain format" value. It is documented in the application
note as a Q6.4 values, up to x63.9375.
One version of the datasheet indicates that the sensor supports a
digital gain:
The OV5640 supports 1/2/4 digital gain. Normally, the gain is
controlled automatically by the automatic gain control (AGC) block.
It isn't clear how that would be controlled manually.
There appears to be no indication regarding whether the gain controlled
through registers 0x350a and 0x350b is an analogue gain only or also
includes digital gain. The words "real gain" don't necessarily mean
"combined analogue and digital gains". Some OmniVision sensors (such as
the OV8858) are documented as supoprting different formats for the gain
values, selectable through a register bit, and they are called "real
gain format" and "sensor gain format". For that sensor, we have (one of)
the gain registers documented as
0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are
fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain
If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse
gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1,
gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain,
0x70 is 4x gain
(The second part of the text makes little sense)
"Real gain" may thus refer to the combination of the coarse and fine
analogue gains as a single value.
The OV5640 0x350a and 0x350b registers thus appear to control analogue
gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific
control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it.
If registers 0x350a and 0x350b are later found to control digital gain
as well, the driver could then restrict the range of the analogue gain
control value to lower than x64 and add a separate digital gain control.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Picked-from: https://lore.kernel.org/all/20221128080201.15104-1-laurent.pinchart@ideasonboard.com/
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Some userspace libraries don't work well when two different bus formats
are used by the same V4L2 pixel format, so remove the older 2X8 formats.
These were initially kept to not break backward compatibility, but all
sensors we currently support use the correct 1X16 formats.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Some userspace libraries like libcamera call STREAMON ioctl before
queuing any frames using QBUF. Our driver cannot directly support this
usage, as we need at least one frame to be queued before we can issue
calls to the DMA engine.
In such cases, VB2 framework can defer calling the start_streaming
callback, provided our driver places a requirement on minimum number of
queued buffers it requires.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
[ Upstream commit 06710cd5d2436135046898d7e4b9408c8bb99446 ]
Few of the H264 encoder registers written were not getting reflected
since the read values were not stored and getting overwritten.
Fixes: 6a9c6f681257 ("[media] s5p-mfc: Add variants to access mfc registers")
Cc: stable@vger.kernel.org
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d3f3c2fe54e30b0636496d842ffbb5ad3a547f9b ]
During error on CLOSE_INSTANCE command, ctx_work_bits was not getting
cleared. During consequent mfc execution NULL pointer dereferencing of
this context led to kernel panic. This patch fixes this issue by making
sure to clear ctx_work_bits always.
Fixes: 818cd91ab8c6 ("[media] s5p-mfc: Extract open/close MFC instance commands")
Cc: stable@vger.kernel.org
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8a46bc4e1e0446459daa77c4ce14218d32dacf9 ]
On receiving last buffer driver puts MFC to MFCINST_FINISHING state which
in turn skips transferring of frame from SRC to REF queue. This causes
driver to stop MFC encoding and last frame is lost.
This patch guarantees safe handling of frames during MFCINST_FINISHING and
correct clearing of workbit to avoid early stopping of encoding.
Fixes: af9357467810 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Cc: stable@vger.kernel.org
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fd3d91ab1c6ab0628fe642dd570b56302c30a792 upstream.
The dvb-core tries to sync the releases of opened files at
dvb_dmxdev_release() with two refcounts: dvbdev->users and
dvr_dvbdev->users. A problem is present in those two syncs: when yet
another dvb_demux_open() is called during those sync waits,
dvb_demux_open() continues to process even if the device is being
closed. This includes the increment of the former refcount, resulting
in the leftover refcount after the sync of the latter refcount at
dvb_dmxdev_release(). It ends up with use-after-free, since the
function believes that all usages were gone and releases the
resources.
This patch addresses the problem by adding the check of dmxdev->exit
flag at dvb_demux_open(), just like dvb_dvr_open() already does. With
the exit flag check, the second call of dvb_demux_open() fails, hence
the further corruption can be avoided.
Also for avoiding the races of the dmxdev->exit flag reference, this
patch serializes the dmxdev->exit set up and the sync waits with the
dmxdev->mutex lock at dvb_dmxdev_release(). Without the mutex lock,
dvb_demux_open() (or dvb_dvr_open()) may run concurrently with
dvb_dmxdev_release(), which allows to skip the exit flag check and
continue the open process that is being closed.
CVE-2022-41218 is assigned to those bugs above.
Reported-by: Hyunwoo Kim <imv4bel@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/20220908132754.30532-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b0d0477fce747d4137aa65856318b55fba72198 upstream.
In function dvb_register_device() -> dvb_register_media_device() ->
dvb_create_media_entity(), dvb->entity is allocated and initialized. If
the initialization fails, it frees the dvb->entity, and return an error
code. The caller takes the error code and handles the error by calling
dvb_media_device_free(), which unregisters the entity and frees the
field again if it is not NULL. As dvb->entity may not NULLed in
dvb_create_media_entity() when the allocation of dvbdev->pad fails, a
double free may occur. This may also cause an Use After free in
media_device_unregister_entity().
Fix this by storing NULL to dvb->entity when it is freed.
Link: https://lore.kernel.org/linux-media/20220426052921.2088416-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Fixes: fcd5ce4b3936 ("media: dvb-core: fix a memory leak bug")
Cc: stable@vger.kernel.org
Cc: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7392134428c92a4cb541bd5c8f4f5c8d2e88364d upstream.
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. Use `s8` and `u8` types here, since that's what
surrounding code does. This fixes:
drivers/media/dvb-frontends/stv0288.c:471 stv0288_set_frontend() warn: assigning (-9) to unsigned variable 'tm'
drivers/media/dvb-frontends/stv0288.c:471 stv0288_set_frontend() warn: we never enter this loop
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-media@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a664569b71b0a52be5ffb9fb87cc4f83d29bd71 upstream.
Previous commit initialize the dvbdev->ref before the template copy,
which will overwrite the reference and cause refcnt bug.
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 0 PID: 1 at lib/refcount.c:25 refcount_warn_saturate+0x17c/0x1f0 lib/refcount.c:25
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc6-next-20221128-syzkaller #0
...
RIP: 0010:refcount_warn_saturate+0x17c/0x1f0 lib/refcount.c:25
RSP: 0000:ffffc900000678d0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88813ff58000 RSI: ffffffff81660e7c RDI: fffff5200000cf0c
RBP: ffff888022a45010 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000000 R12: 0000000000000001
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff88823ffff000 CR3: 000000000c48e000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__refcount_add include/linux/refcount.h:199 [inline]
__refcount_inc include/linux/refcount.h:250 [inline]
refcount_inc include/linux/refcount.h:267 [inline]
kref_get include/linux/kref.h:45 [inline]
dvb_device_get drivers/media/dvb-core/dvbdev.c:585 [inline]
dvb_register_device+0xe83/0x16e0 drivers/media/dvb-core/dvbdev.c:517
...
Just place the kref_init at correct position.
Reported-by: syzbot+fce48a3dd3368645bd6c@syzkaller.appspotmail.com
Fixes: 0fc044b2b5e2 ("media: dvbdev: adopts refcnt to avoid UAF")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d21e0b1b41b21d628bf2afce777727bd4479aa5 ]
syzbot reported use-after-free in si470x_int_in_callback() [1]. This
indicates that urb->context, which contains struct si470x_device
object, is freed when si470x_int_in_callback() is called.
The cause of this issue is that si470x_int_in_callback() is called for
freed urb.
si470x_usb_driver_probe() calls si470x_start_usb(), which then calls
usb_submit_urb() and si470x_start(). If si470x_start_usb() fails,
si470x_usb_driver_probe() doesn't kill urb, but it just frees struct
si470x_device object, as depicted below:
si470x_usb_driver_probe()
...
si470x_start_usb()
...
usb_submit_urb()
retval = si470x_start()
return retval
if (retval < 0)
free struct si470x_device object, but don't kill urb
This patch fixes this issue by killing urb when si470x_start_usb()
fails and urb is submitted. If si470x_start_usb() fails and urb is
not submitted, i.e. submitting usb fails, it just frees struct
si470x_device object.
Reported-by: syzbot+9ca7a12fd736d93e0232@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=94ed6dddd5a55e90fd4bab942aa4bb297741d977 [1]
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 94d90fb06b94a90c176270d38861bcba34ce377d ]
Syzbot reports a memory leak in "dvb_usb_adapter_init()".
The leak is due to not accounting for and freeing current iteration's
adapter->priv in case of an error. Currently if an error occurs,
it will exit before incrementing "num_adapters_initalized",
which is used as a reference counter to free all adap->priv
in "dvb_usb_adapter_exit()". There are multiple error paths that
can exit from before incrementing the counter. Including the
error handling paths for "dvb_usb_adapter_stream_init()",
"dvb_usb_adapter_dvb_init()" and "dvb_usb_adapter_frontend_init()"
within "dvb_usb_adapter_init()".
This means that in case of an error in any of these functions the
current iteration is not accounted for and the current iteration's
adap->priv is not freed.
Fix this by freeing the current iteration's adap->priv in the
"stream_init_err:" label in the error path. The rest of the
(accounted for) adap->priv objects are freed in dvb_usb_adapter_exit()
as expected using the num_adapters_initalized variable.
Syzbot report:
BUG: memory leak
unreferenced object 0xffff8881172f1a00 (size 512):
comm "kworker/0:2", pid 139, jiffies 4294994873 (age 10.960s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff844af012>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:75 [inline]
[<ffffffff844af012>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:184 [inline]
[<ffffffff844af012>] dvb_usb_device_init.cold+0x4e5/0x79e drivers/media/usb/dvb-usb/dvb-usb-init.c:308
[<ffffffff830db21d>] dib0700_probe+0x8d/0x1b0 drivers/media/usb/dvb-usb/dib0700_core.c:883
[<ffffffff82d3fdc7>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
[<ffffffff8274af6a>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:782
[<ffffffff8274b786>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:899
[<ffffffff82747c87>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff8274b352>] __device_attach+0x122/0x260 drivers/base/dd.c:970
[<ffffffff827498f6>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff82745cdb>] device_add+0x5fb/0xdf0 drivers/base/core.c:3405
[<ffffffff82d3d202>] usb_set_configuration+0x8f2/0xb80 drivers/usb/core/message.c:2170
[<ffffffff82d4dbfc>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
[<ffffffff82d3f49c>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
Link: https://syzkaller.appspot.com/bug?extid=f66dd31987e6740657be
Reported-and-tested-by: syzbot+f66dd31987e6740657be@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-media/20220824012152.539788-1-mazinalhaddad05@gmail.com
Signed-off-by: Mazin Al Haddad <mazinalhaddad05@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fc044b2b5e2d05a1fa1fb0d7f270367a7855d79 ]
dvb_unregister_device() is known that prone to use-after-free.
That is, the cleanup from dvb_unregister_device() releases the dvb_device
even if there are pointers stored in file->private_data still refer to it.
This patch adds a reference counter into struct dvb_device and delays its
deallocation until no pointer refers to the object.
Link: https://lore.kernel.org/linux-media/20220807145952.10368-1-linma@zju.edu.cn
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a15fe8d9f1bf460a804bcf18a890bfd2cf0d5caa ]
Link: https://lore.kernel.org/linux-media/20220410061925.4107-1-chinayanlei2002@163.com
Signed-off-by: Yan Lei <yan_lei@dahuatech.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e5e5defdb8b0186312c2f855ace175aee6daf9b ]
As the kmalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: cb1d3a336371 ("[media] coda: add CODA7541 JPEG support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b8082238fb8bb20f67e46388123e67a5bbc558d ]
As the coda_iram_alloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: b313bcc9a467 ("[media] coda: simplify IRAM setup")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63ff05a1ad242a5a0f897921c87b70d601bda59c ]
In configure_channels(), we should call of_node_put() when breaking
out of for_each_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: c5f5d0f99794 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57fb35d7542384cac8f198cd1c927540ad38b61a ]
Add missing pci_disable_device() in the error path in saa7164_initdev().
Fixes: 443c1228d505 ("V4L/DVB (12923): SAA7164: Add support for the NXP SAA7164 silicon")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f50ebe10f5d8092c37e2bd430c78e03bf38b1e20 ]
Commit 5441e9dafdfc6dc40 ("[media] s5p-mfc: Core support for MFC v7")
which adds mfc v7 support for Exynos3250 and use the same compatible
string as used by Exynos5240 but both the IPs are a bit different in
terms of IP clock.
Add variant driver data based on the new compatible string
"samsung,exynos3250-mfc" for Exynos3250 SoC.
Suggested-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: 5441e9dafdfc ("[media] s5p-mfc: Core support for MFC v7")
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ed554fd769a19ea8464bb83e9ac201002ef74ad ]
Wei Chen reports a kernel bug as blew:
general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
...
Call Trace:
<TASK>
__i2c_transfer+0x77e/0x1930 drivers/i2c/i2c-core-base.c:2109
i2c_transfer+0x1d5/0x3d0 drivers/i2c/i2c-core-base.c:2170
i2cdev_ioctl_rdwr+0x393/0x660 drivers/i2c/i2c-dev.c:297
i2cdev_ioctl+0x75d/0x9f0 drivers/i2c/i2c-dev.c:458
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl+0xfb/0x170 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fd834a8bded
In az6027_i2c_xfer(), if msg[i].addr is 0x99,
a null-ptr-deref will caused when accessing msg[i].buf.
For msg[i].len is 0 and msg[i].buf is null.
Fix this by checking msg[i].len in az6027_i2c_xfer().
Link: https://lore.kernel.org/lkml/CAO4mrfcPHB5aQJO=mpqV+p8mPLNg-Fok0gw8gZ=zemAfMGTzMg@mail.gmail.com/
Link: https://lore.kernel.org/linux-media/20221120065918.2160782-1-zhongbaisong@huawei.com
Fixes: 76f9a820c867 ("V4L/DVB: AZ6027: Initial import of the driver")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Baisong Zhong <zhongbaisong@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a574359e2e71ce16be212df3a082ed60a4bd2c5f ]
In dvb_register_frontend(), dvb_register_device() is possible to fail
but its return value is ignored.
It will cause use-after-free when module is removed, because in
dvb_unregister_frontend() it tries to unregister a not registered
device.
BUG: KASAN: use-after-free in dvb_remove_device+0x18b/0x1f0 [dvb_core]
Read of size 4 at addr ffff88800dff4824 by task rmmod/428
CPU: 3 PID: 428 Comm: rmmod
Call Trace:
<TASK>
...
dvb_remove_device+0x18b/0x1f0 [dvb_core]
dvb_unregister_frontend+0x7b/0x130 [dvb_core]
vidtv_bridge_remove+0x6e/0x160 [dvb_vidtv_bridge]
...
Fix this by catching return value of dvb_register_device().
However the fe->refcount can't be put to zero immediately, because
there are still modules calling dvb_frontend_detach() when
dvb_register_frontend() fails.
Link: https://lore.kernel.org/linux-media/20221108033005.169095-1-chenzhongjin@huawei.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 813ceef062b53d68f296aa3cb944b21a091fabdb ]
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
Link: https://syzkaller.appspot.com/bug?id=e378e6a51fbe6c5cc43e34f131cc9a315ef0337e
Fixes: 21677cfc562a ("V4L/DVB: ir-core: add imon driver")
Reported-by: syzbot+0c3cb6dc05fbbdc3ad66@syzkaller.appspotmail.com
Signed-off-by: Gautam Menghani <gautammenghani201@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f74d3f326d1d5b8951ce263c59a121ecfa65e7c0 ]
In vimc_init(), when platform_driver_register(&vimc_pdrv) fails,
platform_driver_unregister(&vimc_pdrv) is wrongly called rather than
platform_device_unregister(&vimc_pdev), which causes kernel warning:
Unexpected driver unregister!
WARNING: CPU: 1 PID: 14517 at drivers/base/driver.c:270 driver_unregister+0x8f/0xb0
RIP: 0010:driver_unregister+0x8f/0xb0
Call Trace:
<TASK>
vimc_init+0x7d/0x1000 [vimc]
do_one_initcall+0xd0/0x4e0
do_init_module+0x1cf/0x6b0
load_module+0x65c2/0x7820
Fixes: 4a29b7090749 ("[media] vimc: Subdevices as modules")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b3dc3f8e49577840dc8ac8a365c5b3da4edb10b8 ]
dma_alloc_coherent does not return a physical address, but a DMA address,
which might be remapped or have an offset. Passing the DMA address to
vm_iomap_memory is thus broken.
Use the proper dma_mmap_coherent helper instead, and stop passing
__GFP_COMP to dma_alloc_coherent, as the memory management inside the
DMA allocator is hidden from the callers and does not require it.
With this the gfp_t argument to __videobuf_dc_alloc can be removed and
hard coded to GFP_KERNEL.
Fixes: a8f3c203e19b ("[media] videobuf-dma-contig: add cache support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b434422c45282a0573d8123239abc41fa72665d4 ]
A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b090 ("[media] s5p-fimc: Add the media device driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f5866dd96d95b74e439f6ee17b8abd8195179fb ]
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbce5 ("[media] solo6x10: sync to latest code from Bluecherry's git repo")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba8d9405935097e296bcf7a942c3a01df0edb865 ]
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
...
dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
platform_probe+0xb6/0x170
...
Allocated by task 1238:
...
dvb_register_device+0x1a7/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
Freed by task 1238:
dvb_register_device+0x6d2/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything.
Fixes: f90cf6079bf6 ("media: vidtv: add a bridge driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8f3582345e6a69da65ab588f7c4c2d1685b0e80 ]
It is required to return the received buffers, if streaming can not be
started. For instance media_pipeline_start() may fail with EPIPE, if
a link validation between entities is not passed, and in such a case
a user gets a kernel warning:
WARNING: CPU: 1 PID: 520 at drivers/media/common/videobuf2/videobuf2-core.c:1592 vb2_start_streaming+0xec/0x160
<snip>
Call trace:
vb2_start_streaming+0xec/0x160
vb2_core_streamon+0x9c/0x1a0
vb2_ioctl_streamon+0x68/0xbc
v4l_streamon+0x30/0x3c
__video_do_ioctl+0x184/0x3e0
video_usercopy+0x37c/0x7b0
video_ioctl2+0x24/0x40
v4l2_ioctl+0x4c/0x70
The fix is to correct the error path in video_start_streaming() of camss.
Fixes: 0ac2586c410f ("media: camss: Add files which handle the video device nodes")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e38e42c078da4af962d322b97e726dcb2f184e3f ]
devm_pinctrl_get() may return ERR_PTR(-EPROBE_DEFER), add a minus sign
to fix it.
Fixes: 4163851f7b99 ("[media] s5p-fimc: Use pinctrl API for camera ports configuration")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 94a7ad9283464b75b12516c5512541d467cefcf8 ]
syzkaller found a bug:
BUG: unable to handle page fault for address: ffffc9000a3b1000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 100000067 P4D 100000067 PUD 10015f067 PMD 1121ca067 PTE 0
Oops: 0002 [#1] PREEMPT SMP
CPU: 0 PID: 23489 Comm: vivid-000-vid-c Not tainted 6.1.0-rc1+ #512
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:memcpy_erms+0x6/0x10
[...]
Call Trace:
<TASK>
? tpg_fill_plane_buffer+0x856/0x15b0
vivid_fillbuff+0x8ac/0x1110
vivid_thread_vid_cap_tick+0x361/0xc90
vivid_thread_vid_cap+0x21a/0x3a0
kthread+0x143/0x180
ret_from_fork+0x1f/0x30
</TASK>
This is because we forget to check boundary after adjust compose->height
int V4L2_SEL_TGT_CROP case. Add v4l2_rect_map_inside() to fix this problem
for this case.
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f98a5c2e1c4396488c27274ba82afc11725a4bcc ]
Commit 1f391df44607 ("media: v4l2-async: Use endpoints in
__v4l2_async_nf_add_fwnode_remote()") changed the data that is stored in
the v4l2_async_subdev internals from the fwnode pointer to the parent
device to the fwnode pointer to the matched endpoint. This broke the
sensor matching code, which relied on the particular fwnode data in the
v4l2_async_subdev internals. Fix this by simply matching the
v4l2_async_subdev pointer, which is already available there.
Reported-by: Daniel Scally <djrscally@gmail.com>
Fixes: fa91f1056f17 ("[media] exynos4-is: Add support for asynchronous subdevices registration")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a2822bfe45c50abd9f76a8547a77a1f6a0e8c8d ]
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: f98a5c2e1c43 ("media: exynos4-is: don't rely on the v4l2_async_subdev internals")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f6e8d8c94a82e85e1b9b62a7671990740dc6f70 ]
In the function vcodec_domains_get(), dev_pm_domain_attach_by_name()
may return NULL in some cases, so IS_ERR() doesn't meet the
requirements. Thus fix it.
Fixes: 7482a983dea3 ("media: venus: redesign clocks and pm domains control")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fce241660f37d9e95e93c0ae6fba8cfefa5797b ]
Error path seems to be swaped. Fix the order and provide some meaningful
names.
Fixes: bee3d5115611 ("[media] ad5820: Add driver for auto-focus coil")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f30ce3d3760b22ee33c8d9c2e223764ad30bdc5f ]
As kmalloc can return NULL pointer, it should be better to
check the return value and return error, same as
coda_jpeg_decode_header.
Fixes: 96f6f62c4656 ("media: coda: jpeg: add CODA960 JPEG encoder support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This patch enables the 48bit addressing support which was limited to 32
bit. Change dma_mask value so that wave5 driver can allow 48bit memory
address. Change the u32 type address variable to dma_addr_t to allow
48bit address. Get high_address(higher 16bit) value from common_memory
dma address.
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Tested-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
|
|
2x2 binning works fine for RAW10 capture, but for RAW8 1232p mode it
leads to corrupted frames [1][2].
Using the special 2x2 analog binning mode fixes the issue, but causes
artefacts for RAW10 1232p capture. So here we choose the binning mode
depending upon the frame format selected.
As both binning modes work fine for 480p RAW8 and RAW10 capture, it can
share the same code path as 1232p for selecting binning mode.
[1] https://forums.raspberrypi.com/viewtopic.php?t=332103
[2] https://github.com/raspberrypi/libcamera-apps/issues/281
Fixes: 22da1d56e982 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins
of the sensor directly through the 15-pin FFC connector. Instead wiring
~PWDN gpio to the sensor pins with appropriate delays.
In such cases, reset_gpio will not be available to the driver, but it
will still be toggled when the sensor is powered on, and thus we should
still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3])
before attempting any i/o operations over SCCB.
Also, rename the function to ov5640_powerup_sequence to better match the
datasheet (section 2.7).
[1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf
[2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf
[3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Move the register-based reset out of the init_setting[] and into the
powerup_sequence function. The sensor is power cycled and reset using
the gpio pins so the soft reset is not always necessary.
This also ensures that soft reset honors the timing sequence
from the datasheet [1].
[1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonaboard.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For CSI-2 the correct formats to use for YUV422 are of the form 1x16 as
it is a serial protocol. The formats of the form 2x8 are used for
parallel protocols like DVP.
Add support for the 1x16 formats and make it the default. We still keep
around the 2x8 formats to avoid any regressions.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For CSI-2 the correct formats to use for YUV422 are of the form 1x16 as
it is a serial protocol. The formats of the form 2x8 are used for
parallel protocols like DVP.
Add support for the 1x16 formats and make it the default. We still keep
around the 2x8 formats to avoid any regressions.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
In commit a89f14bbcfa5 ("media: ov5640: Split DVP and CSI-2 formats"),
it splits format list for DVP and CSI-2 mode, but the default format
defined in commit 90b0f355c5a3 ("media: ov5640: Implement init_cfg")
is only supported by DVP mode, so define a new default format for
CSI-2 mode.
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Picked-from: https://lore.kernel.org/all/20221212040526.3549644-1-guoniu.zhou@oss.nxp.com/
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|