| Age | Commit message (Collapse) | Author |
|---|
|
* tag 'v3.2': (83 commits)
Linux 3.2
minixfs: misplaced checks lead to dentry leak
ptrace: ensure JOBCTL_STOP_SIGMASK is not zero after detach
ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE race
Revert "rtc: Expire alarms after the time is set."
[CIFS] default ntlmv2 for cifs mount delayed to 3.3
cifs: fix bad buffer length check in coalesce_t2
Revert "rtc: Disable the alarm in the hardware"
hung_task: fix false positive during vfork
security: Fix security_old_inode_init_security() when CONFIG_SECURITY is not set
fix CAN MAINTAINERS SCM tree type
mwifiex: fix crash during simultaneous scan and connect
b43: fix regression in PIO case
ath9k: Fix kernel panic in AR2427 in AP mode
CAN MAINTAINERS update
net: fsl: fec: fix build for mx23-only kernel
sch_qfq: fix overflow in qfq_update_start()
drm/radeon/kms/atom: fix possible segfault in pm setup
gspca: Fix falling back to lower isoc alt settings
futex: Fix uninterruptible loop due to gate_area
...
|
|
Some cameras will pretty much entirely fill all the image buffers all the
time even though they are using compression.
This patch adds a flag to sd_desc, which drivers for such cameras can set.
When this flag is set the bandwidth calculation code will no longer
assume that the image buffer size is a worst case and less bandwidth than
imagebufsize * fps will be used on average.
This patch sets this new flag for 3 drivers:
* For spca561 (for rev12a cameras) and nw80x cams as these simply don't work
when given less bandwidth than imagebufsize * fps.
* For sn9c20x cameras, because these show severy jpeg artifacts when
given less bandwidth than imagebufsize * fps and since these are usb2
cameras there is plenty bandwidth anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Quoting from the official usb 20 spec:
"5.6.4 Isochronous Transfer Bus Access Constraints
Isochronous transfers can only be used by full-speed and high-speed devices."
This means that for code paths which are isoc mode only, we don't need to
check for the device being low speed, simplifying the code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Check dev->actconfig rather than dev->config when checking various
configuration things. dev->config points to the array of configs for the
device so dev->config->foo boils down to dev->config[0].foo and the first
config is not necessarily always the active config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In case we ever get sub drivers which do 7.5 fps and express this as
15 / 2 fps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The calculated bandwidth should not be multiplied by the interval, but be
divided by it. Also bInterbval should be interpreted as a power of 2
for isochronous endpoints.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After the "gspca: Fix bulk mode cameras no longer working (regression fix)"
patch build_ep_tb is no longer being called for bulk endpoints.
This patch renames build_ep_tb to build_isoc_ep_tb to make clear it should
only be called for isoc mode cameras.
This patch also:
- drops the no longer needed xfer parameter
- removes a check for bulk mode from the build_isoc_ep_tb code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Having:
- a mean image size of 0.375 time the max compressed image size and
- a frame rate of 30 fps for small images or with USB 2.0/3.0
seems more realistic and gives less image freezes.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.
This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!
This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 &
vicam cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 & vicam
cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As the alternate settings are now sorted in gspca main,
the variable 'nbalt' is no more useful.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch is adapted from a patch from Sarah Sharp (2010/05/03).
The xHCD handler checks the USB bandwidth on usb_set_interface()
instead of on usb_submit_urb().
Now, the same treatment is applied in case of error of both functions.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Previously image transfer used to use the highest altsetting, which, most of
the time, took the whole USB bandwidth.
Now, the altsetting is chosen according to an estimation of the bandwidth
needed for image transfer.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In vidioc_enum_fmt_vid_cap, the 'compressed' flag was set from the
pixelformat, and all pixelformats were not treated.
Now, images are told as compressed when the image size is smaller than
its number of pixels.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
For USB speeds different of 'low', the bInterval value is logarithmic.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add pr_fmt.
Convert usb style logging macros to pr_<level>.
Remove now unused old usb style logging macros.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Just like in userspace strncpy does not guarantee 0 termination. Use strlcpy
instead which does guarantee 0 termination.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reset image and image_len to NULL/0 on LAST_PACKET when we're in discard
frame mode, just like we do when not discarding the current frame.
The new se401 driver uses image_len for SOF/EOF detection and thus depends on
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Instead of handling a per-driver driver version, use the
per-subsystem one.
As reviewed by Jean-Francois Moine <moinejf@free.fr>:
- the 'info' may be simplified:
Reviewed-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The USB traces are better done by usbmon which is enabled in most Linux/GNU
distributions and which permits easier comparison with the USB exchanges of
other drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
This patch fixes a bug in gspca, more precisely in alt_xfer().
This function looks for an input transfer endpoint in an alternate setting.
By default it returns the first endpoint corresponding to the transfer type
indicated in parameter.
But with some USB devices, the first endpoint corresponding to the transfer
type is not always an INPUT endpoint but an OUTPUT one.
This patch adds the endpoint direction test to be sure to return an INPUT endpoint
Signed-off-by: Patrice CHOTARD <patricechotard@free.fr>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- change copyright and erroneous comment
- small code optimization
- have constant the device template
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We check for not streaming as a condition to abort waiting in dqbuf, so
when another thread does a streamoff we should wake the wq.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Some applications (xawtv, qv4l2) mix read and mmap calls. Allow switching
from read mode back to mmap mode (by doing a reqbufs).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_dev->memory == GSPCA_MEMORY_NO implies gspca_dev->nframes == 0,
so there is no need to check for both in dev_poll. The check in
dev_read also is more complex then needed, as dqbuf which dev_read
calls already does all necessary checks. Moreover dqbuf is holding
the proper locks while checking where as dev_read itself is not.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before this patch we were not setting the memory type to GSPCA_MEMORY_NO
when the buffers were released by the app doing a reqbufs 0. Nor would
the memory type be set to GSPCA_MEMORY_NO on device close, as capture_file
already is NULL on device close because of the reqbufs 0. This caused the
following problem:
-app1 does reqbufs USERPTR for 4 buffers
-app1 does reqbufs USERPTR for 0 buffers
-app2 tries to do reqbufs MMAP for 4 buffers
fails because gspca_dev->memory still is USERPTR
Fixing this also allows an app to switch memory type's by unrequesting
the buffers and re-requesting them of a different type.
This patch also moves the setting of gspca_dev->frsz and gscpa_dev->memory
to after alloc_frame succeeding, so that they are not changed when allocating
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove the no longer used / useful users variable, and with that gone
there also is no longer a need to take queue_lock in dev_open.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before this patch dqbuf errors out on a failing user_copy (with user pointers)
before updating the buffer flags, causing a successsfully dequeued buffer
to still have the DONE flag, which means that it could no longer be
re-queueud (assuming the app somehow survives the segfault).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before this patch vidioc_dqbuf is using its own read_lock, where as
other queue related functions use queue_lock. This means that dqbuf is
accessing several variables in a racy manor. The most important one
being fr_o, which may be changed from underneath dqbuf by vidioc_reqbufs
or vidioc_streamoff. Other variables which it accesses unprotected
are gspca_dev->memory, gspca_dev->streaming and gspca_dev->capt_file.
This patch fixes this by changing vidioc_dqbuf to also use the queue_lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The gspca_dev->streaming boolean is protected against multiple access
through gspca_dev->queue_lock everywhere except for 2 places. This patch
fixes this by bringing it under the lock in vidioc_streamoff. And by
removing the check for gspca_dev->streaming in gspca_disconnect,
the destroy_urbs call may be called multiple times (and is protected
by the usb_lock) and calling wake_up_interruptible can also always be done
safely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The check for status errors is now before the check for len. That's
ok. However, the error printk's for the status error prints the URB
length. This generates this error:
drivers/media/video/gspca/gspca.c: In function ‘fill_frame’:
drivers/media/video/gspca/gspca.c:305:9: warning: ‘len’ may be used uninitialized in this function
The fix is as simple as moving the len init to happen before the checks.
Cc: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Also, in ov534, don't check the parm type.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When an error is set for an isochronous packet, the length of the packet
may be null. In this case, the error was not detected and the image
was not discarded as it should be.
Reported-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Changeset 35680ba broke several devices:
- Sony Playstation Eye (1415:2000);
- Gigaware model 25-234 (0c45:628f);
- Logitech Messenger Plus (046d:08f6).
Probably more devices were broken by this change.
What happens is that several devices don't need to save some bandwidth
for audio.
Also, as pointed by Hans de Goede <hdegoede@redhat.com>, the logic
that implements the bandwidth reservation for audio is broken, since
it will reduce the alt number twice, on devices with audio.
So, let's just revert the broken logic, and think on a better solution
for usb 1.1 devices with audio that can't use the maximum packetsize.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently alloc_and_submit_int_urb() is setting gspca->int_urb
as soon as the allocation has succeeded, but if the subsequent
submit fails, the urb gets destroyed. And then later will
get destroyed again in gspca_input_destroy_urb() because
gspca->int_urb is set, leading to a double free.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently gspca supported usb-1.1 webcams for which we support the input
button through an interrupt endpoint won't stream (not enough bandwidth
error) when used through an USB-2.0 hub.
After much debugging I've found out that the cause for this is that the
ehci-sched.c schedeling code does not like it when there are already urb's
scheduled when (large) isoc urbs are queued. By moving the submission
of the interrupt urbs to after submitting the isoc urbs the camera
starts working again through usb-2.0 hubs.
Note that this does not fix isoc. streaming through a usb-hub while another
1.1 usb device (like the microphone of the same cam) is also active
at the same time :(
I've spend a long time analyzing the linux kernel ehci scheduler code,
resulting in this (long) mail:
http://www.spinics.net/lists/linux-usb/msg37982.html
The conclusion of the following mail thread is that yes there are several
issues when using usb-1.1 devices through a usb-2.0 hub, but these are not
easily fixable in the current code. Fixing this in ehci-sched.c requires
an almost full rewrite, which is not bound to happen anytime soon.
So with this patch gspca driven usb-1.1 webcams will atleast work when
connected through an usb-2.0 hub when the microphone is not used.
As an added bonus this patch avoids extra destroy/create input urb cycles
when we end up falling back to a lower speed alt setting because of bandwidth
limitations.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The errors were found by checkpatch.pl. Most fixes are:
- remove spaces followed by TAB(s),
- split lines greater than 80 characters,
- move most '{'s from start of line to end of previous line.
(Some '{'s at start of line remain when the '}'s are on the same line)
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When audio is present, some alternate settings were skipped.
This prevented some webcams to work, especially when bulk transfer was used.
This patch permits to use the last or only alternate setting.
Reported-by: Antonio Ospite <ospite@studenti.unina.it>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch also sets to 0 the sequence of the first frame.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The new control mechanism uses dynamic control values in the subdriver
descriptor. It simplifies standard control handling.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
