| Age | Commit message (Collapse) | Author |
|---|
|
This is supported in DVB-T2 mode, so added to the T/T2 frontend.
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/dvb/frontends/drxd_hard.c: In function ‘DRX_Start’:
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
[mchehab@redhat.com: removed the status = status assignment after the switch]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
[steve@stevekerrison.com: Remove private definitions from cxd2820r that existed before API was defined]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch removes the remaining on-stack buffer for USB DMA transfer.
This patch also reduces the stack memory usage.
Cc: stable@kernel.org
Cc: Florian Mickler <florian@mickler.org>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove old DVB-T2 freq module param and detect DVB-T/T2 automatically.
Implementation is trial and error, if DVB-T does not lock try DVB-T2
and vice versa. That's done by replacing normal DVBFE_ALGO_SW with
DVBFE_ALGO_CUSTOM which gives better control for tuning process.
DVB-C still uses normal software ZigZag, DVBFE_ALGO_SW.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make checkpatch.pl happy by fixing whitespaces introduced by
commit 79e8b8e3b8cbf67130247a3f6d25732373fe2f34
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It is very first DVB-T2 Linux driver!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Change firmware download split, which I introduced few patch earlier,
a little bit to make it more readable as requested [1].
Anyhow, for some reason this seems to increase compiled binary size
52 bytes, on my AMD64 box, which is rather much for so small change.
[1] http://www.spinics.net/lists/linux-media/msg31968.html
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It is very rare I2C adapter hardware which can provide 32kB I2C write
as one write. Add .i2c_wr_max option to set desired max packet size.
Split transaction to smaller pieces according to that option.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Bits 4 and 5 on register 02 should always be set to 1.
Opera1/Bsru6/z0194a/mantis_vp1033
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Issues with Register 02 causing spurious channel locking from standby.
Should have always bits 4 & 5 written to 1.
Lower nibble not used in any current driver. Usage if necessary can be
applied through initab to mcr_reg. stv0299 not out of standby before
writing inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Gate could close after first I2C message. On stv0288 it does.
Keep 2nd and 3rd message I2C gate control alive.
Remove unnecessary gate closing in this module.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If the second memory allocation in dib9000_attach() fails, we'll leak the
memory allocated by the first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Register 42 bits 2,3,6 and 7 should be set to 0.
This gives difficult locking on some channels and may be compensated
for by other methods.
This affects any driver using the stv0288 frontend on the default
or earda inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add support for TT S-1500 with BSBE1-D01A tuner.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This was replaced by Micronas drxd driver
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The macro is defined as:
#define CHK_ERROR(s) if( (status = s)<0 ) break
This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.
Fixed by this simple perl script:
while (<>) { $f.=$_; };
$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
Plus a few manual adjustments
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.
If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.
The diff result is impressive:
1 files changed, 1013 insertions(+), 12694 deletions(-)
rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)
As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.
The code cleanup was done using this small script:
$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
$ grep -f used_symbols drxd_map_firm.h >defines
And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s/(define\s+[^\s]+)\s........../\1/
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Abstract out the firmware for the drx-d so that it can be loaded by the
request_firmware() interface.
The firmware licensing permits free redistribution, and can be found here:
http://kernellabs.com/firmware/drxd
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Provide the ability for the board configuration to specify whether to insert
the RS byte into the TS interconnect to the bridge, while not required for
the ngene in fact is required for the em28xx.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add the drxd to the Makefile and Kconfig
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
These are the original drx-d sources, extracted from Ralph Metzler's GPL'd
ngene driver. No modifications/cleanup have yet been made. In fact, no
measures have been taken to see if the code even compiles.
Signed-off-by Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
status now returns
FE_HAS_CARRIER
FE_HAS_SIGNAL
FE_HAS_VITERBI
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The CellsCoeffs arrays are [3][6][5] not [2][6][5].
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We use err to store negative error codes so it should be signed. And
if we return an error from stv0367_get_tuner_freq() that needs to be
handled properly as well. (param->frequency is a u32).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
On Thu, 17 Feb 2011, Matthias Schwarzott wrote:
> On Sunday 06 February 2011, Jesper Juhl wrote:
> > If the memory allocation to 'state' succeeds but we jump to the 'error'
> > label before 'state' is assigned to fe->tuner_priv, then the call to
> > 'zl10036_release(fe)' at the 'error:' label will not free 'state', but
> > only what was previously assigned to 'tuner_priv', thus leaking the memory
> > allocated to 'state'.
> > There are may ways to fix this, including assigning the allocated memory
> > directly to 'fe->tuner_priv', but I did not go for that since the
> > additional pointer derefs are more expensive than the local variable, so I
> > just added a 'kfree(state)' call. I guess the call to 'zl10036_release'
> > might not even be needed in this case, but I wasn't sure, so I left it in.
> >
> Yeah, that call to zl10036_release can be completely eleminated.
> Another thing is: jumping to the error label only makes sense when memory was
> already allocated. So the jump in line 471 can be replaced by "return NULL",
> as the other error handling before allocation:
> if (NULL == config) {
> printk(KERN_ERR "%s: no config specified", __func__);
> goto error;
> }
>
> I suggest to improve the patch to clean the code up when changing that.
>
> But I am fine with commiting this patch also if you do not want to change it.
>
Thank you for your feedback. It makes a lot of sense.
Changing it is not a problem :)
How about the updated patch below?
If the memory allocation to 'state' succeeds but we jump to the 'error'
label before 'state' is assigned to fe->tuner_priv, then the call to
'zl10036_release(fe)' at the 'error:' label will not free 'state', but
only what was previously assigned to 'tuner_priv', thus leaking the memory
allocated to 'state'.
This patch fixes the leak and also does not jump to 'error:' before mem
has been allocated but instead just returns. Also some small style
cleanups.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Split FW download packages smarter way and bug free. Implementation is
based of Andrea Merello's example he provided for tda18218 driver.
Count remaining FW bytes down in loop instead of division and modulo
combination used earlier.
Thanks to: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Quick test shows that FW must be running before other checks
so make it happen earlier.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/dvb/frontends/stv0367.c: In function 'stv0367ter_lock_algo':
drivers/media/dvb/frontends/stv0367.c:1315:2: warning: cast from pointer to integer of different size
Use %p to print addresses instead of 0x%x.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It is taken from another tree, where it is modified.
Patch to fix that
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Simptoms:
After zapping DVB-S2 channel searching for DVB-S tooks long time.
Now it takes less than a second.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
dib9000_mbx_send_attr() returns an int. It doesn't work to save
negative error codes in an unsigned char, so I've made "ret" an int
type.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
kfree(state) if fe allocation fails.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
kmalloc() can fail so check whether state->internal is NULL.
append_internal() can return NULL on allocation failures so check that.
Also if we hit the error condition later in the function then there is
a memory leak and we need to call remove_dev() to fix it.
Also Oliver Endriss pointed out an additional leak that I missed in the
first version of this patch.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The card uses ds3000 demod from Montage.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
