| Age | Commit message (Collapse) | Author |
|---|
|
Since hub usb2517 is going to be supported by the usb251xb driver,
the bindings need to be properly updated. Particularly:
- add "microchip,usb2517" and "microchip,usb2517i" compatible strings.
- add "boolean" description to all the properties, which really accept
a boolean value including a new one "led-{usb,speed}-mode".
- move reset-gpios property to the optional section. It isn't
defined as required in the code and shouldn't be required at all, since
hardware may handle reset pins by itself.
- add new led-{usb,speed}-mode mode property. USB2517 device supports
two LED modes: USB mode and speed (default) indication mode. The last one
can be switched on by this property.
- add {bp,sp}-max-{total,removable}-current-microamp property measured in
microamp. It hasn't been defined as property before. Since the limitation
specified by these parameters is hardware specific it needs to be defined
in dts.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Documentation modification, now interrupt-parent is an optional
property. Also fix few typos.
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.15
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.15 merge window
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here are a small number of patches to resolve some reported IIO and a
staging driver problem. Nothing major here, full details are in the
shortlog below.
All have been in linux-next with no reported issues"
* tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: bcm2835-audio: Fix memory corruption
iio: adc: at91-sama5d2_adc: fix probe error on missing trigger property
iio: adc: dln2-adc: fix build error
iio: dummy: events: Add missing break
staging: iio: ade7759: fix signed extension bug on shift of a u8
iio: pressure: zpa2326: Remove always-true check which confuses gcc
iio: proximity: as3935: noise detection + threshold changes
|
|
Remove dummy clocks for usb wakeup and add optional ones for
MCU_BUS_CK and DMA_BUS_CK.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Define two new properties: brcm,rx-aeq-mode which allows configuring the
SATA PHY RX equalizers and when "manual" is used, brcm,rx-aeq can be
used to set the exact value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds binding for r8a77995 (R-Car D3). Since r8a77995 doesn't
have dedicated pins (ID, VBUS), this will match against the generic
fallback on R-Car D3.
For now, this driver doesn't support usb role swap for r8a77995.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add USB PHY support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5)
USB PHY is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of small fixes mostly in the irq drivers area:
- Make the tango irq chip work correctly, which requires a new
function in the generiq irq chip implementation
- A set of updates to the GIC-V3 ITS driver removing a bogus BUG_ON()
and parsing the VCPU table size correctly"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack()
irqchip/tango: Use irq_gc_mask_disable_and_ack_set
genirq: generic chip: Add irq_gc_mask_disable_and_ack_set()
irqchip/gic-v3-its: Add missing changes to support 52bit physical address
irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size
irqchip/gic-v3-its: Fix the incorrect BUG_ON in its_init_vpe_domain()
DT: arm,gic-v3: Update the ITS size in the examples
|
|
Commit 764f80798b95 ("doc: Add RCU files to docbook-generation files")
added :external: options for RCU source files in the file
Documentation/core-api/kernel-api.rst. However, this now means nothing,
so this commit removes them.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds support for r8a7743/5 SoCs. The Renesas RZ/G1[ME]
(R8A7743/5) usbhs is identical to the R-Car Gen2 family.
No driver change is needed due to the fallback compatible value
"renesas,rcar-gen2-usbhs".
Adding the SoC-specific compatible values here has two purposes:
1. Document which SoCs have this hardware module,
2. Allow checkpatch to validate compatible values.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Remove optional pinctrls due to using FORCE/RG_IDDIG to implement
manual switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Remove dummy clocks for usb wakeup and add optional ones for
mcu_bus and dma_bus bus.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds binding documentation for DWC2 controller in HS mode found
on STMicroelectronics STM32F7xx SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This adds a short document describing the views of how the Linux kernel
community feels about enforcing the license of the kernel.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Alex Elder (Linaro) <elder@linaro.org>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Anna Schumaker <schumaker.anna@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Darrick J. Wong (Oracle) <darrick.wong@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Acked-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hannes Reinecke <hare@suse.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ivan Safonov <insafonov@gmail.com>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Acked-by: Jan Kara (SUSE) <jack@suse.cz>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Joe Perches <joe@perches.com>
Acked-by: Joerg Roedel (SUSE) <jroedel@suse.de>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Laura Abbott <laura@labbott.name>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Linus Walleij (Linaro) <linus.walleij@linaro.org>
Acked-by: Lv Zheng <zetalog@gmail.com>
Acked-by: Martin K. Petersen (Oracle) <martin.petersen@oracle.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Rik van Riel <riel@surriel.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sebastian Reichel (Collabora) <sre@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Takashi Iwai (SUSE) <tiwai@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Luck <tony.luck@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.14 cycle.
* ade7759
- Fix a signed extension bug.
* as3935
- The default noise and watch dog settings were such that the device
was unusuable in most applications. Add device tree parameters to
allow it to be configured to something that will actually work.
* at91-sama5d2 adc
- Fix handling of legacy device trees that don't provide the new
trigger edge property.
* dln2-adc
- Fix a missing Kconfig dependency on IIO_TRIGGERED_BUFFER.
* dummy driver
- Add a missing break so that writing in_voltage0_thresh_rising_en
doesn't always result in an error.
* zpa2326
- Drop a test for an always true condition so that gcc won't spit out
and unused variable warning.
|
|
When the VMA based swap readahead was introduced, a new knob
/sys/kernel/mm/swap/vma_ra_max_order
was added as the max window of VMA swap readahead. This is to make it
possible to use different max window for VMA based readahead and
original physical readahead. But Minchan Kim pointed out that this will
cause a regression because setting page-cluster sysctl to zero cannot
disable swap readahead with the change.
To fix the regression, the page-cluster sysctl is used as the max window
of both the VMA based swap readahead and original physical swap
readahead. If more fine grained control is needed in the future, more
knobs can be added as the subordinate knobs of the page-cluster sysctl.
The vma_ra_max_order knob is deleted. Because the knob was introduced
in v4.14-rc1, and this patch is targeting being merged before v4.14
releasing, there should be no existing users of this newly added ABI.
Link: http://lkml.kernel.org/r/20171011070847.16003-1-ying.huang@intel.com
Fixes: ec560175c0b6fce ("mm, swap: VMA based swap readahead")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reported-by: Minchan Kim <minchan@kernel.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Pull networking fixes from David Miller:
1) Fix object leak on IPSEC offload failure, from Steffen Klassert.
2) Fix range checks in ipset address range addition operations, from
Jozsef Kadlecsik.
3) Fix pernet ops unregistration order in ipset, from Florian Westphal.
4) Add missing netlink attribute policy for nl80211 packet pattern
attrs, from Peng Xu.
5) Fix PPP device destruction race, from Guillaume Nault.
6) Write marks get lost when BPF verifier processes R1=R2 register
assignments, causing incorrect liveness information and less state
pruning. Fix from Alexei Starovoitov.
7) Fix blockhole routes so that they are marked dead and therefore not
cached in sockets, otherwise IPSEC stops working. From Steffen
Klassert.
8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
net: thunderx: mark expected switch fall-throughs in nicvf_main()
udp: fix bcast packet reception
netlink: do not set cb_running if dump's start() errs
ipv4: Fix traffic triggered IPsec connections.
ipv6: Fix traffic triggered IPsec connections.
ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
Revert commit 1a8b6d76dc5b ("net:add one common config...")
ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
ixgbe: Return error when getting PHY address if PHY access is not supported
netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
tipc: Unclone message at secondary destination lookup
tipc: correct initialization of skb list
gso: fix payload length when gso_size is zero
mlxsw: spectrum_router: Avoid expensive lookup during route removal
bpf: fix liveness marking
doc: Fix typo "8023.ad" in bonding documentation
ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
...
|
|
This merges in the USB fixes that we need here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Should be "802.3ad" like everywhere else in the document.
Signed-off-by: Axel Beckert <abe@deuxchevaux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix a regression in 4.14 and one in 4.13. The latter is a case when
Docker is doing something it really shouldn't and gets away with it.
We now print a warning instead of erroring out.
There are also fixes to several error paths"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix regression caused by exclusive upper/work dir protection
ovl: fix missing unlock_rename() in ovl_do_copy_up()
ovl: fix dentry leak in ovl_indexdir_cleanup()
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
ovl: fix error value printed in ovl_lookup_index()
ovl: fix may_write_real() for overlayfs directories
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
|
|
There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action. They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.
This commit fixes a condition that is reported incorrectly. When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array. When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
curr_resync_completed = <max dev size> (but not MaxSector)
and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync. This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.
This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process. Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().
Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
|
|
Enforcing exclusive ownership on upper/work dirs caused a docker
regression: https://github.com/moby/moby/issues/34672.
Euan spotted the regression and pointed to the offending commit.
Vivek has brought the regression to my attention and provided this
reproducer:
Terminal 1:
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
Terminal 2:
unshare -m
Terminal 1:
umount merged
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
mount: /root/overlay-testing/merged: none already mounted or mount point
busy
To fix the regression, I replaced the error with an alarming warning.
With index feature enabled, mount does fail, but logs a suggestion to
override exclusive dir protection by disabling index.
Note that index=off mount does take the inuse locks, so a concurrent
index=off will issue the warning and a concurrent index=on mount will fail.
Documentation was updated to reflect this change.
Fixes: 2cac0c00a6cd ("ovl: get exclusive ownership on upper/work dirs")
Cc: <stable@vger.kernel.org> # v4.13
Reported-by: Euan Kemp <euank@euank.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
|
|
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Adds bindings documentation for the max3421 driver.
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into fixes
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixlet from Tejun Heo:
"Minor documentation update"
* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
Documentation: core-api: minor workqueue.rst cleanups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
serial issues. Nothing major, a documentation update, timing fix,
error handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sccnxp: Fix error handling in sccnxp_probe()
tty: serial: lpuart: avoid report NULL interrupt
serial: bcm63xx: fix timing issue.
mxser: fix timeout calculation for low rates
serial: sh-sci: document R8A77970 bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are a few small fixes for 4.14-rc4.
The removal of DRIVER_ATTR() was almost completed by 4.14-rc1, but one
straggler made it in through some other tree (odds are, one of
mine...) So there's a simple removal of the last user, and then
finally the macro is removed from the tree.
There's a fix for old crazy udev instances that insist on reloading a
module when it is removed from the kernel due to the new uevents for
bind/unbind. This fixes the reported regression, hopefully some year
in the future we can drop the workaround, once users update to the
latest version, but I'm not holding my breath.
And then there's a build fix for a linker warning, and a buffer
overflow fix to match the PCI fixes you took through the PCI tree in
the same area.
All of these have been in linux-next for a few weeks while I've been
traveling, sorry for the delay"
* tag 'driver-core-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: remove DRIVER_ATTR
fpga: altera-cvp: remove DRIVER_ATTR() usage
driver core: platform: Don't read past the end of "driver_override" buffer
base: arch_topology: fix section mismatch build warnings
driver core: suppress sending MODALIAS in UNBIND uevents
|
|
Add DT bindings document for Broadcom STB USB PHYs
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
|
