summaryrefslogtreecommitdiff
path: root/Documentation/hwmon
AgeCommit message (Collapse)Author
2023-03-10hwmon: (ftsteutates) Fix scaling of measurementsArmin Wolf
[ Upstream commit ca8fd8c16a8b77dfcf7f6ce52d2c863220693a78 ] A user complained that the ftsteutates driver was displaying bogus values since its introduction. This happens because the sensor measurements need to be scaled in order to produce meaningful results: - the fan speed needs to be multiplied by 60 since its in RPS - the temperature is in degrees celsius and needs an offset of 64 - the voltage is in 1/256 of 3.3V The offical datasheet says the voltage needs to be divided by 256, but this is likely an off-by-one-error, since even the BIOS devides by 255 (otherwise 3.3V could not be measured). The voltage channels additionally need a board-specific multiplier, however this can be done by the driver since its board-specific. The reason the missing scaling of measurements is the way Fujitsu used this driver when it was still out-of-tree. Back then, all scaling was done in userspace by libsensors, even the generic one. Tested on a Fujitsu DS3401-B1. Fixes: 08426eda58e0 ("hwmon: Add driver for FTS BMC chip "Teutates"") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20221224041855.83981-2-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-10-22hwmon: (corsair-psu) Add USB id of the new HX1500i psuWilken Gottwalt
Also update the documentation accordingly. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net> Link: https://lore.kernel.org/r/Y0FghqQCHG/cX5Jz@monster.localdomain Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-10-02hwmon: (corsair-psu) add USB id of new revision of the HX1000i psuWilken Gottwalt
Also updates the documentation accordingly. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net> Link: https://lore.kernel.org/r/YznOUQ7Pijedu0NW@monster.localdomain Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-25hwmon: (pwm-fan) Switch regulator dynamicallyAlexander Stein
This adds the enable attribute which is used to select if zero PWM duty means to switch off regulator and PWM or to keep them enabled but at inactive PWM output level. Depending on the select enable mode, turn off the regulator and PWM if the PWM duty is zero, or keep them enabled. This is especially important for fan using inverted PWM signal polarity. Having regulator supplied and PWM disabled, some PWM controllers provide the active, rather than inactive signal. With this change the shutdown as well as suspend/resume paths require modifcations as well. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Link: https://lore.kernel.org/r/20220914153137.613982-6-alexander.stein@ew.tq-group.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-25hwmon: (pmbus) Add driver for the TEXAS TPS546D24 Buck Converter.Duke Du
Add the pmbus driver for TEXAS tps546d24 Buck Converter. The vout mode of tps546d24 supported relative data format, which is not supported by the PMBus core. Signed-off-by: Duke Du <dukedu83@gmail.com> Link: https://lore.kernel.org/r/1662951668-9849-1-git-send-email-Duke.Du@quantatw.com [groeck: Add __maybe_unused to tps546d24_of_match declaration] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-20docs: hwmon: add max31760 documentationIbrahim Tilki
Adding documentation for max31760 fan speed controller Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com> Link: https://lore.kernel.org/r/20220910171945.48088-3-Ibrahim.Tilki@analog.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19hwmon: (aquacomputer_d5next) Add support for Aquacomputer High Flow NextAleksa Savic
Extend aquacomputer_d5next driver to expose various hardware sensors of the Aquacomputer High Flow Next flow sensor, which communicates through a proprietary USB HID protocol. The High Flow Next exposes +5V voltages, water quality, conductivity and flow readings. A temperature sensor can be connected to it, in which case it provides its reading and an estimation of the dissipated/absorbed power in the liquid cooling loop. Additionally, serial number and firmware version are exposed through debugfs. Registry offsets were discovered and tested by users on Github [1] [2]. [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8 [2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34 Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20220907100739.806571-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19docs: hwmon: add emc2305.rst to docsMichael Shych
Add description of emc2305 driver. Signed-off-by: Michael Shych <michaelsh@nvidia.com> Reviewed-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20220810171552.56417-4-michaelsh@nvidia.com [groeck: Fixed htmldocs warnings] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19hwmon: (max31790) add fanN_enableJustin Ledford
The MAX31790 has a tach input enable bit in each fan's configuration register. This is only enabled by the driver if RPM mode is selected, but the driver doesn't provide a way to independently enable tachometer input regardless of the regulator mode. By adding the fanN_enable sysfs files, we can decouple the tach input from the regulator mode. Also update the documentation. Signed-off-by: Justin Ledford <justinledford@google.com> Link: https://lore.kernel.org/r/20220829195930.2521755-1-justinledford@google.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19hwmon: (corsair-psu) add reporting of rail mode via debugfsWilken Gottwalt
Add reporting if the PSU is running in single or multi rail mode via ocpmode debugfs entry. Also update the documentation and driver comments accordingly. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net> Link: https://lore.kernel.org/r/YvS9PZKr0xqFqJny@monster.localdomain Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19hwmon: (aquacomputer_d5next) Add support for reading virtual temp sensorsAleksa Savic
Add support for reading virtual temperature sensors for the D5 Next, Octo, Quadro and Farbwerk 360. Virtual temperature sensors are written to the device by the user, pulling from an arbitrary value source. Writing to them is not yet reverse engineered, so the only way to set them for now is to use the official software. Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20220817121441.112198-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-09-19hwmon: (asus_wmi_ec_sensors) remove driverEugene Shalygin
This driver utilises a WMI interface found in AMD 500 series ASUS boards, to read EC registers. But it turned out that ASUS abandoned the interface, as it disappeared from Intel 600 series boards. Additionally, the WMI interface was incredibly slow. Therefore this driver was deprecated in favor of the asus_ec_sensors driver, which supports more boards, more sensors, and is faster. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-08-02Merge tag 'docs-6.0' of git://git.lwn.net/linuxLinus Torvalds
Pull documentation updates from Jonathan Corbet: "This was a moderately busy cycle for documentation, but nothing all that earth-shaking: - More Chinese translations, and an update to the Italian translations. The Japanese, Korean, and traditional Chinese translations are more-or-less unmaintained at this point, instead. - Some build-system performance improvements. - The removal of the archaic submitting-drivers.rst document, with the movement of what useful material that remained into other docs. - Improvements to sphinx-pre-install to, hopefully, give more useful suggestions. - A number of build-warning fixes Plus the usual collection of typo fixes, updates, and more" * tag 'docs-6.0' of git://git.lwn.net/linux: (92 commits) docs: efi-stub: Fix paths for x86 / arm stubs Docs/zh_CN: Update the translation of sched-stats to 5.19-rc8 Docs/zh_CN: Update the translation of pci to 5.19-rc8 Docs/zh_CN: Update the translation of pci-iov-howto to 5.19-rc8 Docs/zh_CN: Update the translation of usage to 5.19-rc8 Docs/zh_CN: Update the translation of testing-overview to 5.19-rc8 Docs/zh_CN: Update the translation of sparse to 5.19-rc8 Docs/zh_CN: Update the translation of kasan to 5.19-rc8 Docs/zh_CN: Update the translation of iio_configfs to 5.19-rc8 doc:it_IT: align Italian documentation docs: Remove spurious tag from admin-guide/mm/overcommit-accounting.rst Documentation: process: Update email client instructions for Thunderbird docs: ABI: correct QEMU fw_cfg spec path doc/zh_CN: remove submitting-driver reference from docs docs: zh_TW: align to submitting-drivers removal docs: zh_CN: align to submitting-drivers removal docs: ko_KR: howto: remove reference to removed submitting-drivers docs: ja_JP: howto: remove reference to removed submitting-drivers docs: it_IT: align to submitting-drivers removal docs: process: remove outdated submitting-drivers.rst ...
2022-07-27hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controllerAleksa Savic
Extend aquacomputer_d5next driver to expose hardware temperature sensors and fans of the Aquacomputer Quadro fan controller, which communicates through a proprietary USB HID protocol. Implemented by Jack Doan [1]. Four temperature sensors and PWM controllable fans are available. The liquid flow sensor is also exposed, implemented by Leonard Anderweit [2]. Additionally, serial number, firmware version and power-on count are exposed through debugfs. This driver has been tested on x86_64. [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5 [2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9 Originally-from: Jack Doan <me@jackdoan.com> Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-27hwmon: (dell-smm) Improve documentationArmin Wolf
Notify users of this driver that each pwmX attribute controls fan number X, meaning that probing of pwm channels is unnecessary. Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20220727083004.5684-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-14docs: process: remove outdated submitting-drivers.rstLukas Bulwahn
Commit 31b24bee3357 ("docs: add a warning to submitting-drivers.rst") in October 2016 already warns "This (...) should maybe just be deleted, but I'm not quite ready to do that yet". Maybe, six years ago, we were not ready but let us remove old content for the better now and structure and maintain less content in the kernel documentation with a better result. Drop this already outdated document and adjust all textual references. Here is an argument why deleting the content will not remove any useful information to the existing kernel documentation, individually broken down for each section. Section "Allocating Device Numbers" refers to https://www.lanana.org/, and then refers to Documentation/admin-guide/devices.rst. However, the devices.rst clearly states: "The version of this document at lanana.org is no longer maintained." Everything needed for submitting drivers is already stated in devices.rst and the reference to https://www.lanana.org/ is outdated, and should be just deleted. Section "Who To Submit Drivers To" is all about Linux 2.0 - 2.6, before the new release version scheme; the mentioned developers are still around, but actually not the first developers to contact anymore. Section "What Criteria Determine Acceptance" has a few bullet points: Licensing and Copyright is well-covered in process/kernel-license.rst. Interfaces, Code, Portability, Clarity state some obvious things about ensuring kernel code quality. Control suggests to add a MAINTAINERS entry, which is already mentioned in 6.Followthrough.rst: "... added yourself to the MAINTAINERS file..." PM support states a bit about implementing and testing power management of a driver, it remains an open question where to place that in the process documents. Driver developers interested in power management will find the corresponding part on power management in the kernel documentation anyway. In section "What Criteria Do Not Determine Acceptance", the points Vendor and Author states something basic consequence of the kernel being an open-source community software development. Probably no need to mention it nowadays. Section "Resources" lists resources that are also mentioned elsewhere more central. - Linux kernel tree and mailing list is mentioned in many places. - https://lwn.net/Kernel/LDD3/ is mentioned in Documentation/process/kernel-docs.rst. - https://lwn.net/ is mentioned in: - Documentation/process/8.Conclusion.rst - Documentation/process/kernel-docs.rst - https://kernelnewbies.org/ is mentioned in: - Documentation/process/8.Conclusion.rst - Documentation/process/kernel-docs.rst - http://www.linux-usb.org/ is mentioned in Documentation/driver-api/usb/usb.rst - https://landley.net/kdocs/ols/2002/ols2002-pages-545-555.pdf is mentioned in Documentation/process/kernel-docs.rst - https://kernelnewbies.org/KernelJanitors is mentioned in Documentation/process/howto.rst - https://git-scm.com/ is mentioned in - Documentation/process/2.Process.rst - Documentation/process/7.AdvancedTopics.rst - Documentation/process/howto.rst Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20220704122537.3407-7-lukas.bulwahn@gmail.com Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2022-07-13hwmon: (asus-ec-sensors) add definitions for ROG ZENITH II EXTREMEUrs Schroffenegger
Add definitions for ROG ZENITH II EXTREME and some unknown yet temperature sensors in the second EC bank. Details are available at [1, 2]. [1] https://github.com/zeule/asus-ec-sensors/pull/26 [2] https://github.com/zeule/asus-ec-sensors/issues/16 Signed-off-by: Urs Schroffenegger <nabajour@lampshade.ch> Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220710202639.1812058-2-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (asus-ec-sensors) add support for Maximus XI HeroMichael Carns
Add definitions for ROG MAXIMUS XI HERO and ROG MAXIMUS XI HERO (WI-FI) boards. Signed-off-by: Michael Carns <mike@carns.com> Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220627225437.87462-1-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (asus-ec-sensors) add support for Strix Z690-a D4Shady Nawara
adds T_Sensor and VRM Temp sensors for the Asus Strix z690-a D4 motherboard Signed-off-by: Shady Nawara <shady.nawara@outlook.com> Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220603122758.1561064-1-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (pmbus) Add support for Analog Devices LT7182SGuenter Roeck
Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase Step-Down Silent Switcher with Digital Power System Management. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support and detection of Philips/NXP NE1618Guenter Roeck
NE1618 is similar to NE1617 but supports manufacturer and chip ID registers as well as 11 bit external temperature resolution. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add explicit support for ADM1020Guenter Roeck
ADM1020 is compatible with ADM1021 but has a separate chip revision and a limited I2C address range. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for ON Semiconductor NCT218Guenter Roeck
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet error checking). Similar to NCT72 and NCT214, PEC support is undocumented. Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when reading those registers. The value for the chip revision register is not documented but was observed to be 0xca. Use that information to improve chip detection accuracy. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for ON Semiconductor NCT214 and NCT72Guenter Roeck
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full PEC (packet error checking) support. PEC support is undocumented. Both chips support the undocumented secondary chip and manufacturer ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this information to improve the accuracy of chip detection code. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add explicit support for NCT210Guenter Roeck
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature offset register. A real chip was found to have a chip revision of 0x3f. Use it to detect NCT210 explicitly. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add remaining chips supported by adm1021 driverGuenter Roeck
All chips supported by the ADM1021 driver are also supported by the LM90 driver. Make that support official. After this change, the adm1021 driver is only needed if the lm90 driver is disabled. Also, the adm1021 driver misdetects a variety of chips as MAX1617A, which is unwanted if any of those chips is in the system. For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to show that it is not needed if the lm90 driver is enabled, and to avoid misdetection if a chip supported by the lm90 driver is in the system. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for ADM1021, ADM1021A, and ADM1023Guenter Roeck
Both chips are quite similar to other chips of this series, so add support for them to the lm90 driver. Also mention ON Semiconductor NCT210, which is pin and register compatible to ADM1021A. None of the chips support the secondary manufacturer and chip ID registers at 0x3e and 0x3f, but return 0 when reading from those registers. Use that information to improve the accuracy of chip detection code. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Support MAX1617 and LM84Guenter Roeck
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily be supported by the LM90 driver. The most difficult part is chip detection, since those old chips do not support manufacturer ID or chip ID registers. The "alarms" attribute is enabled for both chips to match the functionality of the adm1021 driver. Chip detection was improved and is less prone to misdetection than the chip detection in the adm1021 driver. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for MAX6642Guenter Roeck
MAX6642 is a reduced version of LM90 with no low limits and no conversion rate register. Its alert functionality is broken, similar to many other chips supported by the lm90 driver. After this change, the stand-alone max6642 driver is only needed if the lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that it is not needed if the lm90 driver is enabled. A devicetree node is not added for this chip since it is quite unlikely that such an old chip will ever be used in a devicetree based system. It can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for MAX6690Guenter Roeck
MAX6690 is all but identical to MAX6654. Revision 1 of its datasheet lists the same chip ID as MAX6654, and a chip labeled MAX6654 was found to have the chip ID listed as MAX6690 chip ID in Revision 2 of its datasheet. A devicetree node is not added for this chip since it is quite unlikely that such an old chip will ever be used in a devicetree based system. It can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add support for ADT7481, ADT7482, and ADT7483Guenter Roeck
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two external temperature sensors, similar to MAX6695/6696. They support an extended temperature range similar to ADT7461. Registers for the second external channel can be accessed directly or by using the same method as used by MAX6695/6696. For simplicity, the access method implemented for MAX6695/6696 is used. The chips support PEC (packet error checking). Set the PEC feature flag and let the user decide if it should be enabled or not (it is by default disabled). Even though it is only documented for ADT7483, all three chips support a secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f. Use the contents of those registers register for improved chip detection accuracy. Add the same check to the ADT7461A detection code since this chip also supports the same (undocumented) registers. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Reviewed-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add explicit support for MAX6648/MAX6692Guenter Roeck
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support a temperature range of 0..127 degrees C. Separate support for the two sets of chips to be able to support maximum temperature ranges correctly for all chips. Introduce new feature flag to indicate temperature support up to 255 degrees C. Since the chips are almost identical except for the supported temperature range, automatic chip detection is limited. Effectively this means that MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is nothing we can do about that. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Add partial PEC support for ADT7461Guenter Roeck
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC (packet error checking). This information is gone in later versions of the datasheet. Experiments show that PEC support on ADT7461 is similar to PEC support in ADM1032, ie it is only supported for read operations. Add support for it to the driver. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (lm90) Improve PEC supportGuenter Roeck
PEC (packet error checking) support for ADM1032 is currently only enabled if the chip was auto-detected, but not if a chip is instantiated explicitly. Always enable PEC support by introducing a chip feature flag indicating partial PEC support. Also, for consistency, disable PEC support by default to match existing functionality if the chip was not auto- detected. At the same time, introduce generic support for PEC with a separate feature flag. This will be used when support for chips with full PEC functionality is added. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-07-13hwmon: (pmbus) Move pec attribute to I2C deviceGuenter Roeck
Enabling and disabling PEC for PMBus devices is currently only supported with a debugfs attribute, which requires debugfs to be enabled and is thus less than perfect. Take the lm90 driver as example and add a 'pec' attribute to the I2C device if both the I2C adapter and the PMBus device support it. Remove the now obsolete 'pec' attribute from debugfs. Cc: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-22hwmon: Make chip parameter for with_info API mandatoryGuenter Roeck
Various attempts were made recently to "convert" the old hwmon_device_register() API to devm_hwmon_device_register_with_info() by just changing the function name without actually converting the driver. Prevent this from happening by making the 'chip' parameter of devm_hwmon_device_register_with_info() mandatory. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-22hwmon: (asus-ec-sensors) add ROG STRIX X570-E GAMING WIFI IIDebabrata Banerjee
Adds support for the ROG STRIX X570-E GAMING WIFI II board and simplifies formatting for the list of supported models. Signed-off-by: Debabrata Banerjee <dbavatar@gmail.com> Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220505073351.123753-1-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-22hwmon: add driver for the Microchip LAN966x SoCMichael Walle
Add support for the temperatur sensor and the fan controller on the Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used which can measure temperature and process voltages. But only a forumlae for the temperature sensor is known. Additionally, the SoC support a fan tacho input as well as a PWM signal to control the fan. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc [groeck: Added missing reference in Documentation/hwmon/index.rst] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-22hwmon: (pmbus) Add support for Infineon Digital Multi-phase xdp152 family ↵Greg.Schwendimann@infineon.com
controllers Add support for devices XDPE152C4, XDPE12584. Signed-off-by: Greg Schwendimann <Greg.Schwendimann@infineon.com> Link: https://lore.kernel.org/r/5e6d50e9b28140158f339b0de343eea4@infineon.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) add doc entry for PRIME X470-PROEugene Shalygin
Add PRIME X470-PRO to the list of supported boards. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427180237.1475954-1-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) implement locking via the ACPI global lockEugene Shalygin
For some board models ASUS uses the global ACPI lock to guard access to the hardware, so do we. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427143001.1443605-3-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (pmbus/max16601) Add MAX16602 supportAtif Ofluoglu
Adding another MAX16602 chip support to MAX16601 driver Tested with MAX16602 works as expected. Signed-off-by: Atif Ofluoglu <atif.ofluoglu@maximintegrated.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (aquacomputer_d5next) Add support for Aquacomputer FarbwerkJack Doan
Extend aquacomputer_d5next driver to expose hardware temperature sensors of the Aquacomputer Farbwerk RGB controller, which communicates through a proprietary USB HID protocol. Four temperature sensors are available. Additionally, serial number and firmware version are exposed through debugfs. Also, add Jack Doan to MAINTAINERS for this driver. Signed-off-by: Jack Doan <me@jackdoan.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (dell-smm) Update Documentation regarding firmware bugsArmin Wolf
When adding the Inspiron 3505 to the fan type blacklist, the Documentation was not updated to mention the firmware bug on this machine. Fix that. Fixes: 6ba463edccb9 (hwmon: (dell-smm) Add Inspiron 3505 to fan type blacklist) Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20220424154824.9396-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-17hwmon: (dell-smm) Add cooling device supportArmin Wolf
Until now, only the temperature sensors where exported thru the thermal subsystem. Export the fans as "dell-smm-fan[1-3]" too to make them available as cooling devices. Also update Documentation and fix a minor issue with the alphabetic ordering of the includes. Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20220410163935.7840-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-17hwmon: (asus-ec-sensors) add ProArt X570 Creator WIFI boardEugene Shalygin
Basing on information and testing provided by users [1] add support for another board, ASUS ProArt X570 Creator WiFi. [1] https://github.com/zeule/asus-ec-sensors/issues/17 Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220422111737.1352610-1-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-17hwmon: introduce hwmon_sanitize_name()Michael Walle
More and more drivers will check for bad characters in the hwmon name and all are using the same code snippet. Consolidate that code by adding a new hwmon_sanitize_name() function. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20220405092452.4033674-2-michael@walle.cc Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-17hwmon: (aquacomputer_d5next) Add support for Aquacomputer OctoAleksa Savic
Extend aquacomputer_d5next driver to expose hardware temperature sensors and fans of the Aquacomputer Octo fan controller, which communicates through a proprietary USB HID protocol. Four temperature sensors and eight PWM controllable fans are available. Additionally, serial number, firmware version and power-on count are exposed through debugfs. This driver has been tested on x86_64. Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20220404134212.9690-1-savicaleksa83@gmail.com [groeck: Add missing "select CRC16"] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-03-28Merge tag 'char-misc-5.18-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc and other driver updates from Greg KH: "Here is the big set of char/misc and other small driver subsystem updates for 5.18-rc1. Included in here are merges from driver subsystems which contain: - iio driver updates and new drivers - fsi driver updates - fpga driver updates - habanalabs driver updates and support for new hardware - soundwire driver updates and new drivers - phy driver updates and new drivers - coresight driver updates - icc driver updates Individual changes include: - mei driver updates - interconnect driver updates - new PECI driver subsystem added - vmci driver updates - lots of tiny misc/char driver updates All of these have been in linux-next for a while with no reported problems" * tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits) firmware: google: Properly state IOMEM dependency kgdbts: fix return value of __setup handler firmware: sysfb: fix platform-device leak in error path firmware: stratix10-svc: add missing callback parameter on RSU arm64: dts: qcom: add non-secure domain property to fastrpc nodes misc: fastrpc: Add dma handle implementation misc: fastrpc: Add fdlist implementation misc: fastrpc: Add helper function to get list and page misc: fastrpc: Add support to secure memory map dt-bindings: misc: add fastrpc domain vmid property misc: fastrpc: check before loading process to the DSP misc: fastrpc: add secure domain support dt-bindings: misc: add property to support non-secure DSP misc: fastrpc: Add support to get DSP capabilities misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP misc: fastrpc: separate fastrpc device from channel context dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells dt-bindings: nvmem: make "reg" property optional nvmem: brcm_nvram: parse NVRAM content into NVMEM cells nvmem: dt-bindings: Fix the error of dt-bindings check ...
2022-03-25Merge tag 'mfd-next-5.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "New Drivers: - Add support for Maxim MAX77714 PMIC Removed Drivers: - Remove support for ST-Ericsson AB8500 DebugFS New Device Support: - Add support for Silergy SY7636A to Simple MFD I2C - Add support for MediaTek MT6366 PMIC to MT6358 IRQ - Add support for Charger to Intel PMIC CRC - Add support for Raptor Lake to Intel LPSS PCI New Functionality: - Add support for Reboot to Rockchip RK808 Fix-ups: - Device Tree changes (includcing YAML conversion) for silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577, maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic, stericsson,ab8500, stericsson,db8500-prcmu, samsung,exynos5433-lpass, mt6397, syscon, brcm,cru - Visible to menuconfig; simple-mfd-i2c - Clean-up or clarify code; max77686, intel_soc_pmic_crc - Improve error handling; mc13xxx-core, stmfx, asic3 - Pass device information to child devices; iqs62x, intel-lpss-acpi - Individually identify IRQ domains; intel_soc_pmic_core - Remove superfluous code; dbx500-prcmu, exynos-lpass - Staticify and constify; arizona-i2c - Mark sometimes used data as __maybe_unused; atmel-flexcom - Account for different ACPI tables on AOSP/Windows platforms; arizona-spi - Use provided (platform) APIs; ab8500-core - Trivial (whitespace, spelling); rohm-bd9576" * tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits) dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible mfd: bd9576: fix typos in comments mfd: Use platform_get_irq() to get the interrupt mfd: db8500-prcmu: Remove unused inline function mfd: arizona-spi: Add Android board ACPI table handling mfd: arizona-spi: Split Windows ACPI init code into its own function mfd: asic3: Add missing iounmap() on error asic3_mfd_probe MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS mfd: intel-lpss: Provide an SSP type to the driver dt-bindings: mfd: brcm,cru: Rename pinctrl node dt-bindings: Add compatibles for undocumented trivial syscons mfd: atmel-flexcom: Fix compilation warning dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema mfd: exynos-lpass: Drop unneeded syscon.h include mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs mfd: ab8500: Drop debugfs module mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC mfd: ab8500: Rewrite bindings in YAML mfd: qcom-spmi-pmic: Add pm8953 compatible ...
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-06 04:22:28 +0000