| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
It appears that we wrongly calculate dev_base for type1 config cycles.
The thing is: we shouldn't subtract hose->first_busno because PCI core
sets PCI primary, secondary and subordinate bus numbers, and PCIe
controller actually takes the registers into account. So we should use
just bus->number.
Also, according to MPC8315 reference manual, primary bus number should
always remain 0. We have PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS quirk
in indirect_pci.c, but since 83xx is somewhat special, it doesn't use
indirect_pci.c routines, so we have to implement the quirk specifically
for 83xx PCIe controllers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
e821ea70f3b4873b50056a1e0f74befed1014c09 introduced a bug by copying
some 64-bit originated code as-is to be used by both 32 and 64-bit
but this code contains a 64-bit ony "cmpdi" instruction.
This changes it to cmpwi, which is fine since VRSAVE can only contains
a 32-bit value anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@kernel.org>
|
|
Conflicts:
include/linux/kvm.h
|
|
On Fri, 2009-12-04 at 20:59 +1100, Benjamin Herrenschmidt wrote:
> On Fri, 2009-12-04 at 10:34 +0100, Jean Delvare wrote:
> > I've sent it to linuxppc-dev@ozlabs.org on October 14th. This is the
> > address which is listed 22 times in MAINTAINERS. If it isn't correct,
> > then please update MAINTAINERS.
> No it's fine both shoul work. Your patches are there, just waiting for
> me to pick them up, I was just firing a reminder to the rest of the CC
> list :-) (and I do remember fwd'ing a couple of your patches to the
> list, for some reason they didn't make it to patchwork back then, that
> was a few month ago).
> Anyways, I've been stretched thin with all sort of stuff lately, so bear
> with me if I'm a bit slow at taking or testing stuff, I'm doing my best.
Adding patterns to the PowerPC sections of MAINTAINERS is useful.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
At the moment when we EOI an interrupt we set the CPPR back to 0xFF
regardless of its previous value. This could lead to problems if we
take an interrupt with a priority of 5, but before EOIing it we get
an IPI which has a priority of 4. The problem is that at the moment
when we EOI the IPI we will set the CPPR to 0xFF, but it should
really be set back to 5 (the previous priority).
To keep track of the previous CPPR values we create the xics_cppr
structure that has an array for CPPR values and an index pointing
to the current priority. This can easily grow if new priorities get
added in the future.
This will also be useful because the partition adjunct option of
upcoming machines will update the H_XIRR hcall to accept the CPPR
as a parameter.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The recent patch to add cpu offline/online as part of the DLPAR
process for pseries causes a build break if CONFIG_SMP is not
defined. Original patch here;
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-November/078299.html
This corrects the build break by moving the online_node_cpus
and offline_node_cpus under the #ifdef CONFIG_ARCH_CPU_PROBE_RELEASE
portions of dlpar.c.
This patch also slightly modifies the online_node_cpus and offline_node_cpus
routines to prepend dlpar_ to the them and make them static. These two
routine are only used in the dlpar add/remove of cpus and these changes
should help clarify that.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Use symbolic constant for PRESENT and avoid branching.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There is no need to do set the DIRTY bit directly in DTLB Error.
Trap to do_page_fault() and let the generic MM code do the work.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Now that 8xx can fixup dcbX instructions, start using them
where possible like every other PowerPc arch do.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
8xx has not had WRITETHRU due to lack of bits in the pte.
After the recent rewrite of the 8xx TLB code, there are
two bits left. Use one of them to WRITETHRU.
Perhaps use the last SW bit to PAGE_SPECIAL or PAGE_FILE?
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
only DTLB Miss did set this bit, DTLB Error needs too otherwise
the setting is lost when the page becomes dirty.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is an assembler version to fixup DAR not being set
by dcbX, icbi instructions. There are two versions, one
uses selfmodifing code, the other uses a
jump table but is much bigger(default).
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
dcbz, dcbf, dcbi, dcbst and icbi do not set DAR when they
cause a DTLB Error. Dectect this by tagging DAR with 0x00f0
at every exception exit that modifies DAR.
Test for DAR=0x00f0 in DataTLBError and bail
to handle_page_fault().
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Update the TLB asm to make proper use of _PAGE_DIRY and _PAGE_ACCESSED.
Get rid of _PAGE_HWWRITE too.
Pros:
- I/D TLB Miss never needs to write to the linux pte.
- _PAGE_ACCESSED is only set on TLB Error fixing accounting
- _PAGE_DIRTY is mapped to 0x100, the changed bit, and is set directly
when a page has been made dirty.
- Proper RO/RW mapping of user space.
- Free up 2 SW TLB bits in the linux pte(add back _PAGE_WRITETHRU ?)
- kernel RO/user NA support.
Cons:
- A few more instructions in the TLB Miss routines.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
8xx sometimes need to load a invalid/non-present TLBs in
it DTLB asm handler.
These must be invalidated separaly as linux mm don't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
|
|
deallocate
Currently the cpu-allocation/deallocation process comprises of two steps:
- Set the indicators and to update the device tree with DLPAR node
information.
- Online/offline the allocated/deallocated CPU.
This is achieved by writing to the sysfs tunables "probe" during allocation
and "release" during deallocation.
At the sametime, the userspace can independently online/offline the CPUs of
the system using the sysfs tunable "online".
It is quite possible that when a userspace tool offlines a CPU
for the purpose of deallocation and is in the process of updating the device
tree, some other userspace tool could bring the CPU back online by writing to
the "online" sysfs tunable thereby causing the deallocate process to fail.
The solution to this is to serialize writes to the "probe/release" sysfs
tunable with the writes to the "online" sysfs tunable.
This patch employs a mutex to provide this serialization, which is a no-op on
all architectures except PPC_PSERIES
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently the cpu-allocation/deallocation on pSeries is a
two step process from the Userspace.
- Set the indicators and update the device tree by writing to the sysfs
tunable "probe" during allocation and "release" during deallocation.
- Online / Offline the CPUs of the allocated/would_be_deallocated node by
writing to the sysfs tunable "online".
This patch adds kernel code to online/offline the CPUs soon_after/just_before
they have been allocated/would_be_deallocated. This way, the userspace tool
that performs DLPAR operations would only have to deal with one set of sysfs
tunables namely "probe" and release".
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Remove the CPU from the online map to prevent smp_call_function
from sending messages to a stopped CPU.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch adds the specific routines to probe and release (add and remove)
cpu resource for the powerpc pseries platform and registers these handlers
with the ppc_md callout structure.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Version 3 of this patch is updated with documentation added to
Documentation/ABI. There are no changes to any of the C code from v2
of the patch.
In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release. The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.
This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.
The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Dynamic Logical Partitioning capabilities of the powerpc pseries platform
allows for the addition and removal of resources (i.e. CPU's, memory, and PCI
devices) from a partition. The removal of a resource involves
removing the resource's node from the device tree and then returning the
resource to firmware via the rtas set-indicator call. To add a resource, it
is first obtained from firmware via the rtas set-indicator call and then a
new device tree node is created using the ibm,configure-coinnector rtas call
and added to the device tree.
This patch provides the kernel DLPAR infrastructure in a new filed named
dlpar.c. The functionality provided is for acquiring and releasing a resource
from firmware and the parsing of information returned from the
ibm,configure-connector rtas call. Additionally this exports the pSeries
reconfiguration notifier chain so that it can be invoked when device tree
updates are made.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In commit 0512a9a8e277a9de2820211eef964473b714ae65, we unilaterally zero the
"pwm invert" bit in the fan behavior configuration register. On my PowerBook
G4, this results in the fans going to full speed at low temperature and
shutting off at high temperature because the pwm invert bit is supposed to be
set.
Therefore, record the pwm invert bit at driver load time, and write the bit
into the fan behavior control register. This restores correct behavior on my
PBG4 and should work around the bit being set to the wrong value after
suspend/resume (which is what the original patch was trying to fix). It also
fixes a minor omission where the pwm invert bit correction is NOT performed
when switching into automatic mode.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
CC: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Also short-circuit empty updates.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This allows offb to be used for initial framebuffer,
and a kms driver to take over later in the boot sequence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.
The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Remove the old WDT implementation.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cpumask: Use modern cpumask style in Xen
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: UV RTC: Always enable RTC clocksource
x86: UV RTC: Rename generic_interrupt to x86_platform_ipi
x86: UV RTC: Clean up error handling
x86: UV RTC: Add clocksource only boot option
x86: UV RTC: Fix early expiry handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: don't restart timer if disabled
x86: Use -maccumulate-outgoing-args for sane mcount prologues
x86: Prevent GCC 4.4.x (pentium-mmx et al) function prologue wreckage
x86: AMD Northbridge: Verify NB's node is online
x86 VSDO: Fix Kconfig help
x86: Fix typo in Intel CPU cache size descriptor
x86: Add new Intel CPU cache size descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
vgacon: Add support for setting the default cursor state
vc: Add support for hiding the cursor when creating VTs
x86, setup: Store the boot cursor state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-reboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/reboot: Add pci_dev_put in reboot_fixup_32.c for consistency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64: merge the standard and compat start_thread() functions
x86-64: make compat_start_thread() match start_thread()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: pat: Remove ioremap_default()
x86: pat: Clean up req_type special case for reserve_memtype()
x86: Relegate CONFIG_PAT and CONFIG_MTRR configurability to EMBEDDED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ucode-amd: Move family check to microcde_amd.c's init function
x86, ucode-amd: Ensure ucode update on suspend/resume after CPU off/online cycle
x86: ucode-amd: Convert printk(KERN_*...) to pr_*(...)
x86: ucode-amd: Don't warn when no ucode is available for a CPU revision
x86: ucode-amd: Load ucode-patches once and not separately of each CPU
x86, amd-ucode: Remove needless log messages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-entry-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
core: Clean up user return notifers use of per_cpu
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Greg KH <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I messed up the merge in d7fc02c7bae7b1cf69269992cf880a43a350cdaa, where
the conflict in question wasn't just about CTL_UNNUMBERED being removed,
but the 'strategy' field is too (sysctl handling is now done through the
/proc interface, with no duplicate protocols for reading the data).
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits)
arm: omap: Add omap3_defconfig
AM35xx: Defconfig for AM3517 EVM board
AM35xx: Add support for AM3517 EVM board
omap: 3630sdp: defconfig creation
omap: 3630sdp: introduce 3630 sdp board support
omap3: Add defconfig for IGEP v2 board
omap3: Add minimal IGEP v2 support
omap3: Add CompuLab CM-T35 defconfig
omap3: Add CompuLab CM-T35 board support
omap3: rx51: Add wl1251 wlan driver support
omap3: rx51: Add SDRAM init
omap1: Add default kernel configuration for Herald
omap1: Add board support and LCD for HTC Herald
omap: zoom2: update defconfig for LL_DEBUG_NONE
omap: zoom3: defconfig creation
omap3: zoom: Introduce zoom3 board support
omap3: zoom: Drop i2c-1 speed to 2400
omap3: zoom: rename zoom2 name to generic zoom
omap3: zoom: split board file for software reuse
omap3evm: MIgrate to smsc911x ethernet driver
...
Fix trivial conflict (two unrelated config options added next to each
other) in arch/arm/mach-omap2/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: Use hweight32
firewire: cdev: reduce stack usage by ioctl_dispatch
firewire: ohci: 0 may be a valid DMA address
firewire: core: WARN on wrong usage of core transaction functions
firewire: core: optimize Topology Map creation
firewire: core: clarify generate_config_rom usage
firewire: optimize config ROM creation
firewire: cdev: normalize variable names
firewire: normalize style of queue_work wrappers
firewire: cdev: fix memory leak in an error path
|
