summaryrefslogtreecommitdiff
path: root/drivers/usb/serial/io_16654.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/serial/io_16654.h')
-rw-r--r--drivers/usb/serial/io_16654.h195
1 files changed, 195 insertions, 0 deletions
diff --git a/drivers/usb/serial/io_16654.h b/drivers/usb/serial/io_16654.h
new file mode 100644
index 000000000000..a53abc9530ff
--- /dev/null
+++ b/drivers/usb/serial/io_16654.h
@@ -0,0 +1,195 @@
+/************************************************************************
+ *
+ * 16654.H Definitions for 16C654 UART used on EdgePorts
+ *
+ * Copyright (C) 1998 Inside Out Networks, Inc.
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ ************************************************************************/
+
+#if !defined(_16654_H)
+#define _16654_H
+
+/************************************************************************
+ *
+ * D e f i n e s / T y p e d e f s
+ *
+ ************************************************************************/
+
+ //
+ // UART register numbers
+ // Numbers 0-7 are passed to the Edgeport directly. Numbers 8 and
+ // above are used internally to indicate that we must enable access
+ // to them via LCR bit 0x80 or LCR = 0xBF.
+ // The register number sent to the Edgeport is then (x & 0x7).
+ //
+ // Driver must not access registers that affect operation of the
+ // the EdgePort firmware -- that includes THR, RHR, IER, FCR.
+
+
+#define THR 0 // ! Transmit Holding Register (Write)
+#define RDR 0 // ! Receive Holding Register (Read)
+#define IER 1 // ! Interrupt Enable Register
+#define FCR 2 // ! Fifo Control Register (Write)
+#define ISR 2 // Interrupt Status Register (Read)
+#define LCR 3 // Line Control Register
+#define MCR 4 // Modem Control Register
+#define LSR 5 // Line Status Register
+#define MSR 6 // Modem Status Register
+#define SPR 7 // ScratchPad Register
+#define DLL 8 // Bank2[ 0 ] Divisor Latch LSB
+#define DLM 9 // Bank2[ 1 ] Divisor Latch MSB
+#define EFR 10 // Bank2[ 2 ] Extended Function Register
+//efine unused 11 // Bank2[ 3 ]
+#define XON1 12 // Bank2[ 4 ] Xon-1
+#define XON2 13 // Bank2[ 5 ] Xon-2
+#define XOFF1 14 // Bank2[ 6 ] Xoff-1
+#define XOFF2 15 // Bank2[ 7 ] Xoff-2
+
+#define NUM_16654_REGS 16
+
+#define IS_REG_2ND_BANK(x) ((x) >= 8)
+
+ //
+ // Bit definitions for each register
+ //
+
+#define IER_RX 0x01 // Enable receive interrupt
+#define IER_TX 0x02 // Enable transmit interrupt
+#define IER_RXS 0x04 // Enable receive status interrupt
+#define IER_MDM 0x08 // Enable modem status interrupt
+#define IER_SLEEP 0x10 // Enable sleep mode
+#define IER_XOFF 0x20 // Enable s/w flow control (XOFF) interrupt
+#define IER_RTS 0x40 // Enable RTS interrupt
+#define IER_CTS 0x80 // Enable CTS interrupt
+#define IER_ENABLE_ALL 0xFF // Enable all ints
+
+
+#define FCR_FIFO_EN 0x01 // Enable FIFOs
+#define FCR_RXCLR 0x02 // Reset Rx FIFO
+#define FCR_TXCLR 0x04 // Reset Tx FIFO
+#define FCR_DMA_BLK 0x08 // Enable DMA block mode
+#define FCR_TX_LEVEL_MASK 0x30 // Mask for Tx FIFO Level
+#define FCR_TX_LEVEL_8 0x00 // Tx FIFO Level = 8 bytes
+#define FCR_TX_LEVEL_16 0x10 // Tx FIFO Level = 16 bytes
+#define FCR_TX_LEVEL_32 0x20 // Tx FIFO Level = 32 bytes
+#define FCR_TX_LEVEL_56 0x30 // Tx FIFO Level = 56 bytes
+#define FCR_RX_LEVEL_MASK 0xC0 // Mask for Rx FIFO Level
+#define FCR_RX_LEVEL_8 0x00 // Rx FIFO Level = 8 bytes
+#define FCR_RX_LEVEL_16 0x40 // Rx FIFO Level = 16 bytes
+#define FCR_RX_LEVEL_56 0x80 // Rx FIFO Level = 56 bytes
+#define FCR_RX_LEVEL_60 0xC0 // Rx FIFO Level = 60 bytes
+
+
+#define ISR_INT_MDM_STATUS 0x00 // Modem status int pending
+#define ISR_INT_NONE 0x01 // No interrupt pending
+#define ISR_INT_TXRDY 0x02 // Tx ready int pending
+#define ISR_INT_RXRDY 0x04 // Rx ready int pending
+#define ISR_INT_LINE_STATUS 0x06 // Line status int pending
+#define ISR_INT_RX_TIMEOUT 0x0C // Rx timeout int pending
+#define ISR_INT_RX_XOFF 0x10 // Rx Xoff int pending
+#define ISR_INT_RTS_CTS 0x20 // RTS/CTS change int pending
+#define ISR_FIFO_ENABLED 0xC0 // Bits set if FIFOs enabled
+#define ISR_INT_BITS_MASK 0x3E // Mask to isolate valid int causes
+
+
+#define LCR_BITS_5 0x00 // 5 bits/char
+#define LCR_BITS_6 0x01 // 6 bits/char
+#define LCR_BITS_7 0x02 // 7 bits/char
+#define LCR_BITS_8 0x03 // 8 bits/char
+#define LCR_BITS_MASK 0x03 // Mask for bits/char field
+
+#define LCR_STOP_1 0x00 // 1 stop bit
+#define LCR_STOP_1_5 0x04 // 1.5 stop bits (if 5 bits/char)
+#define LCR_STOP_2 0x04 // 2 stop bits (if 6-8 bits/char)
+#define LCR_STOP_MASK 0x04 // Mask for stop bits field
+
+#define LCR_PAR_NONE 0x00 // No parity
+#define LCR_PAR_ODD 0x08 // Odd parity
+#define LCR_PAR_EVEN 0x18 // Even parity
+#define LCR_PAR_MARK 0x28 // Force parity bit to 1
+#define LCR_PAR_SPACE 0x38 // Force parity bit to 0
+#define LCR_PAR_MASK 0x38 // Mask for parity field
+
+#define LCR_SET_BREAK 0x40 // Set Break condition
+#define LCR_DL_ENABLE 0x80 // Enable access to divisor latch
+
+#define LCR_ACCESS_EFR 0xBF // Load this value to access DLL,DLM,
+ // and also the '654-only registers
+ // EFR, XON1, XON2, XOFF1, XOFF2
+
+
+#define MCR_DTR 0x01 // Assert DTR
+#define MCR_RTS 0x02 // Assert RTS
+#define MCR_OUT1 0x04 // Loopback only: Sets state of RI
+#define MCR_MASTER_IE 0x08 // Enable interrupt outputs
+#define MCR_LOOPBACK 0x10 // Set internal (digital) loopback mode
+#define MCR_XON_ANY 0x20 // Enable any char to exit XOFF mode
+#define MCR_IR_ENABLE 0x40 // Enable IrDA functions
+#define MCR_BRG_DIV_4 0x80 // Divide baud rate clk by /4 instead of /1
+
+
+#define LSR_RX_AVAIL 0x01 // Rx data available
+#define LSR_OVER_ERR 0x02 // Rx overrun
+#define LSR_PAR_ERR 0x04 // Rx parity error
+#define LSR_FRM_ERR 0x08 // Rx framing error
+#define LSR_BREAK 0x10 // Rx break condition detected
+#define LSR_TX_EMPTY 0x20 // Tx Fifo empty
+#define LSR_TX_ALL_EMPTY 0x40 // Tx Fifo and shift register empty
+#define LSR_FIFO_ERR 0x80 // Rx Fifo contains at least 1 erred char
+
+
+#define EDGEPORT_MSR_DELTA_CTS 0x01 // CTS changed from last read
+#define EDGEPORT_MSR_DELTA_DSR 0x02 // DSR changed from last read
+#define EDGEPORT_MSR_DELTA_RI 0x04 // RI changed from 0 -> 1
+#define EDGEPORT_MSR_DELTA_CD 0x08 // CD changed from last read
+#define EDGEPORT_MSR_CTS 0x10 // Current state of CTS
+#define EDGEPORT_MSR_DSR 0x20 // Current state of DSR
+#define EDGEPORT_MSR_RI 0x40 // Current state of RI
+#define EDGEPORT_MSR_CD 0x80 // Current state of CD
+
+
+
+ // Tx Rx
+ //-------------------------------
+#define EFR_SWFC_NONE 0x00 // None None
+#define EFR_SWFC_RX1 0x02 // None XOFF1
+#define EFR_SWFC_RX2 0x01 // None XOFF2
+#define EFR_SWFC_RX12 0x03 // None XOFF1 & XOFF2
+#define EFR_SWFC_TX1 0x08 // XOFF1 None
+#define EFR_SWFC_TX1_RX1 0x0a // XOFF1 XOFF1
+#define EFR_SWFC_TX1_RX2 0x09 // XOFF1 XOFF2
+#define EFR_SWFC_TX1_RX12 0x0b // XOFF1 XOFF1 & XOFF2
+#define EFR_SWFC_TX2 0x04 // XOFF2 None
+#define EFR_SWFC_TX2_RX1 0x06 // XOFF2 XOFF1
+#define EFR_SWFC_TX2_RX2 0x05 // XOFF2 XOFF2
+#define EFR_SWFC_TX2_RX12 0x07 // XOFF2 XOFF1 & XOFF2
+#define EFR_SWFC_TX12 0x0c // XOFF1 & XOFF2 None
+#define EFR_SWFC_TX12_RX1 0x0e // XOFF1 & XOFF2 XOFF1
+#define EFR_SWFC_TX12_RX2 0x0d // XOFF1 & XOFF2 XOFF2
+#define EFR_SWFC_TX12_RX12 0x0f // XOFF1 & XOFF2 XOFF1 & XOFF2
+
+#define EFR_TX_FC_MASK 0x0c // Mask to isolate Rx flow control
+#define EFR_TX_FC_NONE 0x00 // No Tx Xon/Xoff flow control
+#define EFR_TX_FC_X1 0x08 // Transmit Xon1/Xoff1
+#define EFR_TX_FC_X2 0x04 // Transmit Xon2/Xoff2
+#define EFR_TX_FC_X1_2 0x0c // Transmit Xon1&2/Xoff1&2
+
+#define EFR_RX_FC_MASK 0x03 // Mask to isolate Rx flow control
+#define EFR_RX_FC_NONE 0x00 // No Rx Xon/Xoff flow control
+#define EFR_RX_FC_X1 0x02 // Receiver compares Xon1/Xoff1
+#define EFR_RX_FC_X2 0x01 // Receiver compares Xon2/Xoff2
+#define EFR_RX_FC_X1_2 0x03 // Receiver compares Xon1&2/Xoff1&2
+
+
+#define EFR_SWFC_MASK 0x0F // Mask for software flow control field
+#define EFR_ENABLE_16654 0x10 // Enable 16C654 features
+#define EFR_SPEC_DETECT 0x20 // Enable special character detect interrupt
+#define EFR_AUTO_RTS 0x40 // Use RTS for Rx flow control
+#define EFR_AUTO_CTS 0x80 // Use CTS for Tx flow control
+
+#endif // if !defined(_16654_H)
+