diff options
Diffstat (limited to 'drivers/tty/serial')
28 files changed, 252 insertions, 322 deletions
diff --git a/drivers/tty/serial/8250.c b/drivers/tty/serial/8250.c index b40f7b90c81d..b4129f53fb1b 100644 --- a/drivers/tty/serial/8250.c +++ b/drivers/tty/serial/8250.c @@ -3318,6 +3318,7 @@ void serial8250_unregister_port(int line) uart->port.flags &= ~UPF_BOOT_AUTOCONF; uart->port.type = PORT_UNKNOWN; uart->port.dev = &serial8250_isa_devs->dev; + uart->capabilities = uart_config[uart->port.type].flags; uart_add_one_port(&serial8250_reg, &uart->port); } else { uart->port.dev = NULL; diff --git a/drivers/tty/serial/8250_pci.c b/drivers/tty/serial/8250_pci.c index 4b4968a294b2..cf35e0dc5085 100644 --- a/drivers/tty/serial/8250_pci.c +++ b/drivers/tty/serial/8250_pci.c @@ -743,7 +743,7 @@ pci_ni8430_setup(struct serial_private *priv, len = pci_resource_len(priv->dev, bar); p = ioremap_nocache(base, len); - /* enable the transciever */ + /* enable the transceiver */ writeb(readb(p + offset + NI8430_PORTCON) | NI8430_PORTCON_TXVR_ENABLE, p + offset + NI8430_PORTCON); @@ -973,7 +973,7 @@ ce4100_serial_setup(struct serial_private *priv, static int pci_omegapci_setup(struct serial_private *priv, - struct pciserial_board *board, + const struct pciserial_board *board, struct uart_port *port, int idx) { return setup_port(priv, port, 2, idx * 8, 0); @@ -994,6 +994,15 @@ static int skip_tx_en_setup(struct serial_private *priv, return pci_default_setup(priv, board, port, idx); } +static int pci_eg20t_init(struct pci_dev *dev) +{ +#if defined(CONFIG_SERIAL_PCH_UART) || defined(CONFIG_SERIAL_PCH_UART_MODULE) + return -ENODEV; +#else + return 0; +#endif +} + /* This should be in linux/pci_ids.h */ #define PCI_VENDOR_ID_SBSMODULARIO 0x124B #define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B @@ -1446,6 +1455,56 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .init = pci_oxsemi_tornado_init, .setup = pci_default_setup, }, + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x8811, + .init = pci_eg20t_init, + }, + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x8812, + .init = pci_eg20t_init, + }, + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x8813, + .init = pci_eg20t_init, + }, + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x8814, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x8027, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x8028, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x8029, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x800C, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x800D, + .init = pci_eg20t_init, + }, + { + .vendor = 0x10DB, + .device = 0x800D, + .init = pci_eg20t_init, + }, /* * Cronyx Omega PCI (PLX-chip based) */ diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 636144cea932..8f41e1123461 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -457,7 +457,6 @@ config SERIAL_SAMSUNG_UARTS_4 config SERIAL_SAMSUNG_UARTS int depends on ARM && PLAT_SAMSUNG - default 2 if ARCH_S3C2400 default 6 if ARCH_S5P6450 default 4 if SERIAL_SAMSUNG_UARTS_4 default 3 @@ -489,13 +488,6 @@ config SERIAL_SAMSUNG_CONSOLE your boot loader about how to pass options to the kernel at boot time.) -config SERIAL_S3C2400 - tristate "Samsung S3C2410 Serial port support" - depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400 - default y if CPU_S3C2400 - help - Serial port support for the Samsung S3C2400 SoC - config SERIAL_S3C2410 tristate "Samsung S3C2410 Serial port support" depends on SERIAL_SAMSUNG && CPU_S3C2410 @@ -519,13 +511,6 @@ config SERIAL_S3C2440 help Serial port support for the Samsung S3C2440, S3C2416 and S3C2442 SoC -config SERIAL_S3C24A0 - tristate "Samsung S3C24A0 Serial port support" - depends on SERIAL_SAMSUNG && CPU_S3C24A0 - default y if CPU_S3C24A0 - help - Serial port support for the Samsung S3C24A0 SoC - config SERIAL_S3C6400 tristate "Samsung S3C6400/S3C6410/S5P6440/S5P6450/S5PC100 Serial port support" depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410 || CPU_S5P6440 || CPU_S5P6450 || CPU_S5PC100) diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index cb2628fee4c7..83b4da6a1062 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -38,11 +38,9 @@ obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o -obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o -obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o obj-$(CONFIG_SERIAL_MAX3100) += max3100.o diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 8dc0541feecc..f5f6831b0a64 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -50,6 +50,7 @@ #include <linux/dmaengine.h> #include <linux/dma-mapping.h> #include <linux/scatterlist.h> +#include <linux/delay.h> #include <asm/io.h> #include <asm/sizes.h> @@ -65,6 +66,30 @@ #define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE) #define UART_DUMMY_DR_RX (1 << 16) + +#define UART_WA_SAVE_NR 14 + +static void pl011_lockup_wa(unsigned long data); +static const u32 uart_wa_reg[UART_WA_SAVE_NR] = { + ST_UART011_DMAWM, + ST_UART011_TIMEOUT, + ST_UART011_LCRH_RX, + UART011_IBRD, + UART011_FBRD, + ST_UART011_LCRH_TX, + UART011_IFLS, + ST_UART011_XFCR, + ST_UART011_XON1, + ST_UART011_XON2, + ST_UART011_XOFF1, + ST_UART011_XOFF2, + UART011_CR, + UART011_IMSC +}; + +static u32 uart_wa_regdata[UART_WA_SAVE_NR]; +static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0); + /* There is by now at least one vendor with differing details, so handle it */ struct vendor_data { unsigned int ifls; @@ -72,6 +97,7 @@ struct vendor_data { unsigned int lcrh_tx; unsigned int lcrh_rx; bool oversampling; + bool interrupt_may_hang; /* vendor-specific */ bool dma_threshold; }; @@ -90,9 +116,12 @@ static struct vendor_data vendor_st = { .lcrh_tx = ST_UART011_LCRH_TX, .lcrh_rx = ST_UART011_LCRH_RX, .oversampling = true, + .interrupt_may_hang = true, .dma_threshold = true, }; +static struct uart_amba_port *amba_ports[UART_NR]; + /* Deals with DMA transactions */ struct pl011_sgbuf { @@ -132,6 +161,7 @@ struct uart_amba_port { unsigned int lcrh_rx; /* vendor-specific */ bool autorts; char type[12]; + bool interrupt_may_hang; /* vendor-specific */ #ifdef CONFIG_DMA_ENGINE /* DMA stuff */ bool using_tx_dma; @@ -1008,6 +1038,68 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap) #endif +/* + * pl011_lockup_wa + * This workaround aims to break the deadlock situation + * when after long transfer over uart in hardware flow + * control, uart interrupt registers cannot be cleared. + * Hence uart transfer gets blocked. + * + * It is seen that during such deadlock condition ICR + * don't get cleared even on multiple write. This leads + * pass_counter to decrease and finally reach zero. This + * can be taken as trigger point to run this UART_BT_WA. + * + */ +static void pl011_lockup_wa(unsigned long data) +{ + struct uart_amba_port *uap = amba_ports[0]; + void __iomem *base = uap->port.membase; + struct circ_buf *xmit = &uap->port.state->xmit; + struct tty_struct *tty = uap->port.state->port.tty; + int buf_empty_retries = 200; + int loop; + + /* Stop HCI layer from submitting data for tx */ + tty->hw_stopped = 1; + while (!uart_circ_empty(xmit)) { + if (buf_empty_retries-- == 0) + break; + udelay(100); + } + + /* Backup registers */ + for (loop = 0; loop < UART_WA_SAVE_NR; loop++) + uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]); + + /* Disable UART so that FIFO data is flushed out */ + writew(0x00, uap->port.membase + UART011_CR); + + /* Soft reset UART module */ + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->reset) + plat->reset(); + } + + /* Restore registers */ + for (loop = 0; loop < UART_WA_SAVE_NR; loop++) + writew(uart_wa_regdata[loop] , + uap->port.membase + uart_wa_reg[loop]); + + /* Initialise the old status of the modem signals */ + uap->old_status = readw(uap->port.membase + UART01x_FR) & + UART01x_FR_MODEM_ANY; + + if (readl(base + UART011_MIS) & 0x2) + printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n"); + + /* Start Tx/Rx */ + tty->hw_stopped = 0; +} + static void pl011_stop_tx(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; @@ -1158,8 +1250,11 @@ static irqreturn_t pl011_int(int irq, void *dev_id) if (status & UART011_TXIS) pl011_tx_chars(uap); - if (pass_counter-- == 0) + if (pass_counter-- == 0) { + if (uap->interrupt_may_hang) + tasklet_schedule(&pl011_lockup_tlet); break; + } status = readw(uap->port.membase + UART011_MIS); } while (status != 0); @@ -1339,6 +1434,14 @@ static int pl011_startup(struct uart_port *port) writew(uap->im, uap->port.membase + UART011_IMSC); spin_unlock_irq(&uap->port.lock); + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->init) + plat->init(); + } + return 0; clk_dis: @@ -1394,6 +1497,15 @@ static void pl011_shutdown(struct uart_port *port) * Shut down the clock producer */ clk_disable(uap->clk); + + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->exit) + plat->exit(); + } + } static void @@ -1700,6 +1812,14 @@ static int __init pl011_console_setup(struct console *co, char *options) if (!uap) return -ENODEV; + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->init) + plat->init(); + } + uap->port.uartclk = clk_get_rate(uap->clk); if (options) @@ -1774,6 +1894,7 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) uap->lcrh_rx = vendor->lcrh_rx; uap->lcrh_tx = vendor->lcrh_tx; uap->fifosize = vendor->fifosize; + uap->interrupt_may_hang = vendor->interrupt_may_hang; uap->port.dev = &dev->dev; uap->port.mapbase = dev->res.start; uap->port.membase = base; diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 6d5d6e679fc7..af9b7814965a 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -1709,12 +1709,13 @@ static int atmel_serial_resume(struct platform_device *pdev) static int __devinit atmel_serial_probe(struct platform_device *pdev) { struct atmel_uart_port *port; + struct atmel_uart_data *pdata = pdev->dev.platform_data; void *data; int ret; BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1)); - port = &atmel_ports[pdev->id]; + port = &atmel_ports[pdata->num]; port->backup_imr = 0; atmel_init_port(port, pdev); diff --git a/drivers/tty/serial/bcm63xx_uart.c b/drivers/tty/serial/bcm63xx_uart.c index a1a0e55d0807..c0b68b9cad91 100644 --- a/drivers/tty/serial/bcm63xx_uart.c +++ b/drivers/tty/serial/bcm63xx_uart.c @@ -250,6 +250,20 @@ static void bcm_uart_do_rx(struct uart_port *port) /* get overrun/fifo empty information from ier * register */ iestat = bcm_uart_readl(port, UART_IR_REG); + + if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) { + unsigned int val; + + /* fifo reset is required to clear + * interrupt */ + val = bcm_uart_readl(port, UART_CTL_REG); + val |= UART_CTL_RSTRXFIFO_MASK; + bcm_uart_writel(port, val, UART_CTL_REG); + + port->icount.overrun++; + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + } + if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY))) break; @@ -284,10 +298,6 @@ static void bcm_uart_do_rx(struct uart_port *port) if (uart_handle_sysrq_char(port, c)) continue; - if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) { - port->icount.overrun++; - tty_insert_flip_char(tty, 0, TTY_OVERRUN); - } if ((cstat & port->ignore_status_mask) == 0) tty_insert_flip_char(tty, c, flag); diff --git a/drivers/tty/serial/bfin_5xx.c b/drivers/tty/serial/bfin_5xx.c index 9b1ff2b6bb37..ff6979181ac5 100644 --- a/drivers/tty/serial/bfin_5xx.c +++ b/drivers/tty/serial/bfin_5xx.c @@ -1304,8 +1304,7 @@ static int bfin_serial_probe(struct platform_device *pdev) goto out_error_free_peripherals; } - uart->port.membase = ioremap(res->start, - res->end - res->start); + uart->port.membase = ioremap(res->start, resource_size(res)); if (!uart->port.membase) { dev_err(&pdev->dev, "Cannot map uart IO\n"); ret = -ENXIO; @@ -1483,7 +1482,7 @@ static int bfin_earlyprintk_probe(struct platform_device *pdev) } bfin_earlyprintk_port.port.membase = ioremap(res->start, - res->end - res->start); + resource_size(res)); if (!bfin_earlyprintk_port.port.membase) { dev_err(&pdev->dev, "Cannot map uart IO\n"); ret = -ENXIO; diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c index 5315525220fb..426434e5eb7c 100644 --- a/drivers/tty/serial/ifx6x60.c +++ b/drivers/tty/serial/ifx6x60.c @@ -36,6 +36,7 @@ * you need to use this driver for another platform. * *****************************************************************************/ +#include <linux/dma-mapping.h> #include <linux/module.h> #include <linux/termios.h> #include <linux/tty.h> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index a54473123e0a..22fe801cce31 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -954,7 +954,7 @@ static void imx_release_port(struct uart_port *port) struct resource *mmres; mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(mmres->start, mmres->end - mmres->start + 1); + release_mem_region(mmres->start, resource_size(mmres)); } /* @@ -970,8 +970,7 @@ static int imx_request_port(struct uart_port *port) if (!mmres) return -ENODEV; - ret = request_mem_region(mmres->start, mmres->end - mmres->start + 1, - "imx-uart"); + ret = request_mem_region(mmres->start, resource_size(mmres), "imx-uart"); return ret ? 0 : -EBUSY; } diff --git a/drivers/tty/serial/jsm/jsm_driver.c b/drivers/tty/serial/jsm/jsm_driver.c index 18f548449c63..96da17868cf3 100644 --- a/drivers/tty/serial/jsm/jsm_driver.c +++ b/drivers/tty/serial/jsm/jsm_driver.c @@ -125,7 +125,7 @@ static int __devinit jsm_probe_one(struct pci_dev *pdev, const struct pci_device brd->bd_uart_offset = 0x200; brd->bd_dividend = 921600; - brd->re_map_membase = ioremap(brd->membase, 0x1000); + brd->re_map_membase = ioremap(brd->membase, pci_resource_len(pdev, 0)); if (!brd->re_map_membase) { dev_err(&pdev->dev, "card has no PCI Memory resources, " diff --git a/drivers/tty/serial/m32r_sio.c b/drivers/tty/serial/m32r_sio.c index 84db7321cce8..8e07517f8acd 100644 --- a/drivers/tty/serial/m32r_sio.c +++ b/drivers/tty/serial/m32r_sio.c @@ -892,7 +892,7 @@ static int m32r_sio_request_port(struct uart_port *port) * If we have a mapbase, then request that as well. */ if (ret == 0 && up->port.flags & UPF_IOREMAP) { - int size = res->end - res->start + 1; + int size = resource_size(res); up->port.membase = ioremap(up->port.mapbase, size); if (!up->port.membase) diff --git a/drivers/tty/serial/mrst_max3110.c b/drivers/tty/serial/mrst_max3110.c index 1bd28450ca40..a764bf99743b 100644 --- a/drivers/tty/serial/mrst_max3110.c +++ b/drivers/tty/serial/mrst_max3110.c @@ -421,7 +421,6 @@ static int max3110_main_thread(void *_max) int ret = 0; struct circ_buf *xmit = &max->con_xmit; - init_waitqueue_head(wq); pr_info(PR_FMT "start main thread\n"); do { @@ -823,7 +822,7 @@ static int __devinit serial_m3110_probe(struct spi_device *spi) res = RC_TAG; ret = max3110_write_then_read(max, (u8 *)&res, (u8 *)&res, 2, 0); if (ret < 0 || res == 0 || res == 0xffff) { - printk(KERN_ERR "MAX3111 deemed not present (conf reg %04x)", + dev_dbg(&spi->dev, "MAX3111 deemed not present (conf reg %04x)", res); ret = -ENODEV; goto err_get_page; @@ -838,6 +837,8 @@ static int __devinit serial_m3110_probe(struct spi_device *spi) max->con_xmit.head = 0; max->con_xmit.tail = 0; + init_waitqueue_head(&max->wq); + max->main_thread = kthread_run(max3110_main_thread, max, "max3110_main"); if (IS_ERR(max->main_thread)) { diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index c911b2419abb..e58cece6f443 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -32,17 +32,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, { struct resource resource; struct device_node *np = ofdev->dev.of_node; - const __be32 *clk, *spd; - const __be32 *prop; - int ret, prop_size; + u32 clk, spd, prop; + int ret; memset(port, 0, sizeof *port); - spd = of_get_property(np, "current-speed", NULL); - clk = of_get_property(np, "clock-frequency", NULL); - if (!clk) { + if (of_property_read_u32(np, "clock-frequency", &clk)) { dev_warn(&ofdev->dev, "no clock-frequency property set\n"); return -ENODEV; } + /* If current-speed was set, then try not to change it. */ + if (of_property_read_u32(np, "current-speed", &spd) == 0) + port->custom_divisor = clk / (16 * spd); ret = of_address_to_resource(np, 0, &resource); if (ret) { @@ -54,25 +54,35 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, port->mapbase = resource.start; /* Check for shifted address mapping */ - prop = of_get_property(np, "reg-offset", &prop_size); - if (prop && (prop_size == sizeof(u32))) - port->mapbase += be32_to_cpup(prop); + if (of_property_read_u32(np, "reg-offset", &prop) == 0) + port->mapbase += prop; /* Check for registers offset within the devices address range */ - prop = of_get_property(np, "reg-shift", &prop_size); - if (prop && (prop_size == sizeof(u32))) - port->regshift = be32_to_cpup(prop); + if (of_property_read_u32(np, "reg-shift", &prop) == 0) + port->regshift = prop; port->irq = irq_of_parse_and_map(np, 0); port->iotype = UPIO_MEM; + if (of_property_read_u32(np, "reg-io-width", &prop) == 0) { + switch (prop) { + case 1: + port->iotype = UPIO_MEM; + break; + case 4: + port->iotype = UPIO_MEM32; + break; + default: + dev_warn(&ofdev->dev, "unsupported reg-io-width (%d)\n", + prop); + return -EINVAL; + } + } + port->type = type; - port->uartclk = be32_to_cpup(clk); + port->uartclk = clk; port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_FIXED_PORT | UPF_FIXED_TYPE; port->dev = &ofdev->dev; - /* If current-speed was set, then try not to change it. */ - if (spd) - port->custom_divisor = be32_to_cpup(clk) / (16 * (be32_to_cpup(spd))); return 0; } @@ -171,6 +181,7 @@ static struct of_device_id __devinitdata of_platform_serial_table[] = { { .compatible = "ns16550", .data = (void *)PORT_16550, }, { .compatible = "ns16750", .data = (void *)PORT_16750, }, { .compatible = "ns16850", .data = (void *)PORT_16850, }, + { .compatible = "nvidia,tegra20-uart", .data = (void *)PORT_TEGRA, }, #ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL { .compatible = "ibm,qpace-nwp-serial", .data = (void *)PORT_NWPSERIAL, }, diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c index 47cadf474149..c37df8d0fa28 100644 --- a/drivers/tty/serial/omap-serial.c +++ b/drivers/tty/serial/omap-serial.c @@ -1241,8 +1241,8 @@ static int serial_omap_probe(struct platform_device *pdev) return -ENODEV; } - if (!request_mem_region(mem->start, (mem->end - mem->start) + 1, - pdev->dev.driver->name)) { + if (!request_mem_region(mem->start, resource_size(mem), + pdev->dev.driver->name)) { dev_err(&pdev->dev, "memory region already claimed\n"); return -EBUSY; } @@ -1308,7 +1308,7 @@ err: dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n", pdev->id, __func__, ret); do_release_region: - release_mem_region(mem->start, (mem->end - mem->start) + 1); + release_mem_region(mem->start, resource_size(mem)); return ret; } diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c index f2cb7503fcb2..465210930890 100644 --- a/drivers/tty/serial/pch_uart.c +++ b/drivers/tty/serial/pch_uart.c @@ -1397,6 +1397,7 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev, int fifosize, base_baud; int port_type; struct pch_uart_driver_data *board; + const char *board_name; board = &drv_dat[id->driver_data]; port_type = board->port_type; @@ -1412,7 +1413,8 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev, base_baud = 1843200; /* 1.8432MHz */ /* quirk for CM-iTC board */ - if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC")) + board_name = dmi_get_system_info(DMI_BOARD_NAME); + if (board_name && strstr(board_name, "CM-iTC")) base_baud = 192000000; /* 192.0MHz */ switch (port_type) { diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c index 4302e6e3768e..531931c1b250 100644 --- a/drivers/tty/serial/pxa.c +++ b/drivers/tty/serial/pxa.c @@ -803,7 +803,7 @@ static int serial_pxa_probe(struct platform_device *dev) break; } - sport->port.membase = ioremap(mmres->start, mmres->end - mmres->start + 1); + sport->port.membase = ioremap(mmres->start, resource_size(mmres)); if (!sport->port.membase) { ret = -ENOMEM; goto err_clk; diff --git a/drivers/tty/serial/s3c2400.c b/drivers/tty/serial/s3c2400.c deleted file mode 100644 index d13051b3df87..000000000000 --- a/drivers/tty/serial/s3c2400.c +++ /dev/null @@ -1,105 +0,0 @@ -/* - * Driver for Samsung SoC onboard UARTs. - * - * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include <linux/module.h> -#include <linux/ioport.h> -#include <linux/io.h> -#include <linux/platform_device.h> - -#include <asm/irq.h> - -#include <mach/hardware.h> - -#include <plat/regs-serial.h> -#include <mach/regs-gpio.h> - -#include "samsung.h" - -static int s3c2400_serial_getsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - clk->divisor = 1; - clk->name = "pclk"; - - return 0; -} - -static int s3c2400_serial_setsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - return 0; -} - -static int s3c2400_serial_resetport(struct uart_port *port, - struct s3c2410_uartcfg *cfg) -{ - dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n", - port, port->mapbase, cfg); - - wr_regl(port, S3C2410_UCON, cfg->ucon); - wr_regl(port, S3C2410_ULCON, cfg->ulcon); - - /* reset both fifos */ - - wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); - wr_regl(port, S3C2410_UFCON, cfg->ufcon); - - return 0; -} - -static struct s3c24xx_uart_info s3c2400_uart_inf = { - .name = "Samsung S3C2400 UART", - .type = PORT_S3C2400, - .fifosize = 16, - .rx_fifomask = S3C2410_UFSTAT_RXMASK, - .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, - .rx_fifofull = S3C2410_UFSTAT_RXFULL, - .tx_fifofull = S3C2410_UFSTAT_TXFULL, - .tx_fifomask = S3C2410_UFSTAT_TXMASK, - .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT, - .get_clksrc = s3c2400_serial_getsource, - .set_clksrc = s3c2400_serial_setsource, - .reset_port = s3c2400_serial_resetport, -}; - -static int s3c2400_serial_probe(struct platform_device *dev) -{ - return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); -} - -static struct platform_driver s3c2400_serial_driver = { - .probe = s3c2400_serial_probe, - .remove = __devexit_p(s3c24xx_serial_remove), - .driver = { - .name = "s3c2400-uart", - .owner = THIS_MODULE, - }, -}; - -s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf); - -static inline int s3c2400_serial_init(void) -{ - return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf); -} - -static inline void s3c2400_serial_exit(void) -{ - platform_driver_unregister(&s3c2400_serial_driver); -} - -module_init(s3c2400_serial_init); -module_exit(s3c2400_serial_exit); - -MODULE_LICENSE("GPL v2"); -MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); -MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver"); -MODULE_ALIAS("platform:s3c2400-uart"); diff --git a/drivers/tty/serial/s3c2410.c b/drivers/tty/serial/s3c2410.c index bffe6ff9b158..b1d7e7c1849d 100644 --- a/drivers/tty/serial/s3c2410.c +++ b/drivers/tty/serial/s3c2410.c @@ -96,8 +96,6 @@ static struct platform_driver s3c2410_serial_driver = { }, }; -s3c24xx_console_init(&s3c2410_serial_driver, &s3c2410_uart_inf); - static int __init s3c2410_serial_init(void) { return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf); diff --git a/drivers/tty/serial/s3c2412.c b/drivers/tty/serial/s3c2412.c index 7e2b9504a687..2234bf9ced45 100644 --- a/drivers/tty/serial/s3c2412.c +++ b/drivers/tty/serial/s3c2412.c @@ -130,8 +130,6 @@ static struct platform_driver s3c2412_serial_driver = { }, }; -s3c24xx_console_init(&s3c2412_serial_driver, &s3c2412_uart_inf); - static inline int s3c2412_serial_init(void) { return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf); diff --git a/drivers/tty/serial/s3c2440.c b/drivers/tty/serial/s3c2440.c index 9e10d415d5fd..1d0c324b813f 100644 --- a/drivers/tty/serial/s3c2440.c +++ b/drivers/tty/serial/s3c2440.c @@ -159,8 +159,6 @@ static struct platform_driver s3c2440_serial_driver = { }, }; -s3c24xx_console_init(&s3c2440_serial_driver, &s3c2440_uart_inf); - static int __init s3c2440_serial_init(void) { return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf); diff --git a/drivers/tty/serial/s3c24a0.c b/drivers/tty/serial/s3c24a0.c deleted file mode 100644 index 914eff22e499..000000000000 --- a/drivers/tty/serial/s3c24a0.c +++ /dev/null @@ -1,117 +0,0 @@ -/* - * Driver for Samsung S3C24A0 SoC onboard UARTs. - * - * Based on drivers/serial/s3c2410.c - * - * Author: Sandeep Patil <sandeep.patil@azingo.com> - * - * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include <linux/module.h> -#include <linux/ioport.h> -#include <linux/platform_device.h> -#include <linux/init.h> -#include <linux/serial_core.h> -#include <linux/serial.h> -#include <linux/io.h> -#include <linux/irq.h> - -#include <mach/hardware.h> - -#include <plat/regs-serial.h> -#include <mach/regs-gpio.h> - -#include "samsung.h" - -static int s3c24a0_serial_setsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - if (strcmp(clk->name, "uclk") == 0) - ucon |= S3C2410_UCON_UCLK; - else - ucon &= ~S3C2410_UCON_UCLK; - - wr_regl(port, S3C2410_UCON, ucon); - return 0; -} - -static int s3c24a0_serial_getsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - clk->divisor = 1; - clk->name = (ucon & S3C2410_UCON_UCLK) ? "uclk" : "pclk"; - - return 0; -} - -static int s3c24a0_serial_resetport(struct uart_port *port, - struct s3c2410_uartcfg *cfg) -{ - dbg("s3c24a0_serial_resetport: port=%p (%08lx), cfg=%p\n", - port, port->mapbase, cfg); - - wr_regl(port, S3C2410_UCON, cfg->ucon); - wr_regl(port, S3C2410_ULCON, cfg->ulcon); - - /* reset both fifos */ - - wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); - wr_regl(port, S3C2410_UFCON, cfg->ufcon); - - return 0; -} - -static struct s3c24xx_uart_info s3c24a0_uart_inf = { - .name = "Samsung S3C24A0 UART", - .type = PORT_S3C2410, - .fifosize = 16, - .rx_fifomask = S3C24A0_UFSTAT_RXMASK, - .rx_fifoshift = S3C24A0_UFSTAT_RXSHIFT, - .rx_fifofull = S3C24A0_UFSTAT_RXFULL, - .tx_fifofull = S3C24A0_UFSTAT_TXFULL, - .tx_fifomask = S3C24A0_UFSTAT_TXMASK, - .tx_fifoshift = S3C24A0_UFSTAT_TXSHIFT, - .get_clksrc = s3c24a0_serial_getsource, - .set_clksrc = s3c24a0_serial_setsource, - .reset_port = s3c24a0_serial_resetport, -}; - -static int s3c24a0_serial_probe(struct platform_device *dev) -{ - return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf); -} - -static struct platform_driver s3c24a0_serial_driver = { - .probe = s3c24a0_serial_probe, - .remove = __devexit_p(s3c24xx_serial_remove), - .driver = { - .name = "s3c24a0-uart", - .owner = THIS_MODULE, - }, -}; - -s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); - -static int __init s3c24a0_serial_init(void) -{ - return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); -} - -static void __exit s3c24a0_serial_exit(void) -{ - platform_driver_unregister(&s3c24a0_serial_driver); -} - -module_init(s3c24a0_serial_init); -module_exit(s3c24a0_serial_exit); - diff --git a/drivers/tty/serial/s3c6400.c b/drivers/tty/serial/s3c6400.c index ded26c42ff37..e2f6913d84d5 100644 --- a/drivers/tty/serial/s3c6400.c +++ b/drivers/tty/serial/s3c6400.c @@ -130,8 +130,6 @@ static struct platform_driver s3c6400_serial_driver = { }, }; -s3c24xx_console_init(&s3c6400_serial_driver, &s3c6400_uart_inf); - static int __init s3c6400_serial_init(void) { return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf); diff --git a/drivers/tty/serial/s5pv210.c b/drivers/tty/serial/s5pv210.c index fb2619f93d84..8dd160c96e87 100644 --- a/drivers/tty/serial/s5pv210.c +++ b/drivers/tty/serial/s5pv210.c @@ -30,7 +30,7 @@ static int s5pv210_serial_setsource(struct uart_port *port, struct s3c2410_uartcfg *cfg = port->dev->platform_data; unsigned long ucon = rd_regl(port, S3C2410_UCON); - if ((cfg->clocks_size) == 1) + if (cfg->flags & NO_NEED_CHECK_CLKSRC) return 0; if (strcmp(clk->name, "pclk") == 0) @@ -55,7 +55,7 @@ static int s5pv210_serial_getsource(struct uart_port *port, clk->divisor = 1; - if ((cfg->clocks_size) == 1) + if (cfg->flags & NO_NEED_CHECK_CLKSRC) return 0; switch (ucon & S5PV210_UCON_CLKMASK) { @@ -135,13 +135,6 @@ static struct platform_driver s5p_serial_driver = { }, }; -static int __init s5pv210_serial_console_init(void) -{ - return s3c24xx_serial_initconsole(&s5p_serial_driver, s5p_uart_inf); -} - -console_initcall(s5pv210_serial_console_init); - static int __init s5p_serial_init(void) { return s3c24xx_serial_init(&s5p_serial_driver, *s5p_uart_inf); diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index f66f64829303..7ead42104c67 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -1416,10 +1416,8 @@ s3c24xx_serial_console_setup(struct console *co, char *options) /* is the port configured? */ - if (port->mapbase == 0x0) { - co->index = 0; - port = &s3c24xx_serial_ports[co->index].port; - } + if (port->mapbase == 0x0) + return -ENODEV; cons_uart = port; @@ -1451,7 +1449,8 @@ static struct console s3c24xx_serial_console = { .flags = CON_PRINTBUFFER, .index = -1, .write = s3c24xx_serial_console_write, - .setup = s3c24xx_serial_console_setup + .setup = s3c24xx_serial_console_setup, + .data = &s3c24xx_uart_drv, }; int s3c24xx_serial_initconsole(struct platform_driver *drv, diff --git a/drivers/tty/serial/samsung.h b/drivers/tty/serial/samsung.h index 5b098cd76040..a69d9a54be94 100644 --- a/drivers/tty/serial/samsung.h +++ b/drivers/tty/serial/samsung.h @@ -79,25 +79,6 @@ extern int s3c24xx_serial_initconsole(struct platform_driver *drv, extern int s3c24xx_serial_init(struct platform_driver *drv, struct s3c24xx_uart_info *info); -#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE - -#define s3c24xx_console_init(__drv, __inf) \ -static int __init s3c_serial_console_init(void) \ -{ \ - struct s3c24xx_uart_info *uinfo[CONFIG_SERIAL_SAMSUNG_UARTS]; \ - int i; \ - \ - for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++) \ - uinfo[i] = __inf; \ - return s3c24xx_serial_initconsole(__drv, uinfo); \ -} \ - \ -console_initcall(s3c_serial_console_init) - -#else -#define s3c24xx_console_init(drv, inf) extern void no_console(void) -#endif - #ifdef CONFIG_SERIAL_SAMSUNG_DEBUG extern void printascii(const char *); diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c index 92aa54550e84..ad0f8f5f6ea1 100644 --- a/drivers/tty/serial/sunsu.c +++ b/drivers/tty/serial/sunsu.c @@ -1435,7 +1435,7 @@ static int __devinit su_probe(struct platform_device *op) rp = &op->resource[0]; up->port.mapbase = rp->start; - up->reg_size = (rp->end - rp->start) + 1; + up->reg_size = resource_size(rp); up->port.membase = of_ioremap(rp, 0, up->reg_size, "su"); if (!up->port.membase) { if (type != SU_PORT_PORT) diff --git a/drivers/tty/serial/vt8500_serial.c b/drivers/tty/serial/vt8500_serial.c index 37fc4e3d487c..026cb9ea5cd1 100644 --- a/drivers/tty/serial/vt8500_serial.c +++ b/drivers/tty/serial/vt8500_serial.c @@ -573,8 +573,7 @@ static int __init vt8500_serial_probe(struct platform_device *pdev) snprintf(vt8500_port->name, sizeof(vt8500_port->name), "VT8500 UART%d", pdev->id); - vt8500_port->uart.membase = ioremap(mmres->start, - mmres->end - mmres->start + 1); + vt8500_port->uart.membase = ioremap(mmres->start, resource_size(mmres)); if (!vt8500_port->uart.membase) { ret = -ENOMEM; goto err; |