summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/68328serial.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/68328serial.h')
-rw-r--r--drivers/tty/serial/68328serial.h186
1 files changed, 0 insertions, 186 deletions
diff --git a/drivers/tty/serial/68328serial.h b/drivers/tty/serial/68328serial.h
deleted file mode 100644
index 3d2faabd766f..000000000000
--- a/drivers/tty/serial/68328serial.h
+++ /dev/null
@@ -1,186 +0,0 @@
-/* 68328serial.h: Definitions for the mc68328 serial driver.
- *
- * Copyright (C) 1995 David S. Miller <davem@caip.rutgers.edu>
- * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>
- * Copyright (C) 1998, 1999 D. Jeff Dionne <jeff@uclinux.org>
- * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com>
- *
- * VZ Support/Fixes Evan Stawnyczy <e@lineo.ca>
- */
-
-#ifndef _MC683XX_SERIAL_H
-#define _MC683XX_SERIAL_H
-
-
-struct serial_struct {
- int type;
- int line;
- int port;
- int irq;
- int flags;
- int xmit_fifo_size;
- int custom_divisor;
- int baud_base;
- unsigned short close_delay;
- char reserved_char[2];
- int hub6; /* FIXME: We don't have AT&T Hub6 boards! */
- unsigned short closing_wait; /* time to wait before closing */
- unsigned short closing_wait2; /* no longer used... */
- int reserved[4];
-};
-
-/*
- * For the close wait times, 0 means wait forever for serial port to
- * flush its output. 65535 means don't wait at all.
- */
-#define S_CLOSING_WAIT_INF 0
-#define S_CLOSING_WAIT_NONE 65535
-
-/*
- * Definitions for S_struct (and serial_struct) flags field
- */
-#define S_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
- on the callout port */
-#define S_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
-#define S_SAK 0x0004 /* Secure Attention Key (Orange book) */
-#define S_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define S_SPD_MASK 0x0030
-#define S_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
-
-#define S_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
-#define S_SPD_CUST 0x0030 /* Use user-specified divisor */
-
-#define S_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
-#define S_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
-#define S_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define S_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
-#define S_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
-
-#define S_FLAGS 0x0FFF /* Possible legal S flags */
-#define S_USR_MASK 0x0430 /* Legal flags that non-privileged
- * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define S_INITIALIZED 0x80000000 /* Serial port was initialized */
-#define S_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
-#define S_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
-#define S_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
-#define S_CLOSING 0x08000000 /* Serial port is closing */
-#define S_CTS_FLOW 0x04000000 /* Do CTS flow control */
-#define S_CHECK_CD 0x02000000 /* i.e., CLOCAL */
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-
-/*
- * I believe this is the optimal setting that reduces the number of interrupts.
- * At high speeds the output might become a little "bursted" (use USTCNT_TXHE
- * if that bothers you), but in most cases it will not, since we try to
- * transmit characters every time rs_interrupt is called. Thus, quite often
- * you'll see that a receive interrupt occures before the transmit one.
- * -- Vladimir Gurevich
- */
-#define USTCNT_TX_INTR_MASK (USTCNT_TXEE)
-
-/*
- * 68328 and 68EZ328 UARTS are a little bit different. EZ328 has special
- * "Old data interrupt" which occures whenever the data stay in the FIFO
- * longer than 30 bits time. This allows us to use FIFO without compromising
- * latency. '328 does not have this feature and without the real 328-based
- * board I would assume that RXRE is the safest setting.
- *
- * For EZ328 I use RXHE (Half empty) interrupt to reduce the number of
- * interrupts. RXFE (receive queue full) causes the system to lose data
- * at least at 115200 baud
- *
- * If your board is busy doing other stuff, you might consider to use
- * RXRE (data ready intrrupt) instead.
- *
- * The other option is to make these INTR masks run-time configurable, so
- * that people can dynamically adapt them according to the current usage.
- * -- Vladimir Gurevich
- */
-
-/* (es) */
-#if defined(CONFIG_M68EZ328) || defined(CONFIG_M68VZ328)
-#define USTCNT_RX_INTR_MASK (USTCNT_RXHE | USTCNT_ODEN)
-#elif defined(CONFIG_M68328)
-#define USTCNT_RX_INTR_MASK (USTCNT_RXRE)
-#else
-#error Please, define the Rx interrupt events for your CPU
-#endif
-/* (/es) */
-
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct m68k_serial {
- char soft_carrier; /* Use soft carrier on this channel */
- char break_abort; /* Is serial console in, so process brk/abrt */
- char is_cons; /* Is this our console. */
-
- /* We need to know the current clock divisor
- * to read the bps rate the chip has currently
- * loaded.
- */
- unsigned char clk_divisor; /* May be 1, 16, 32, or 64 */
- int baud;
- int magic;
- int baud_base;
- int port;
- int irq;
- int flags; /* defined in tty.h */
- int type; /* UART type */
- struct tty_struct *tty;
- int read_status_mask;
- int ignore_status_mask;
- int timeout;
- int xmit_fifo_size;
- int custom_divisor;
- int x_char; /* xon/xoff character */
- int close_delay;
- unsigned short closing_wait;
- unsigned short closing_wait2;
- unsigned long event;
- unsigned long last_active;
- int line;
- int count; /* # of fd on device */
- int blocked_open; /* # of blocked opens */
- unsigned char *xmit_buf;
- int xmit_head;
- int xmit_tail;
- int xmit_cnt;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-};
-
-
-#define SERIAL_MAGIC 0x5301
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-#define SERIAL_XMIT_SIZE 4096
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP 0
-
-/*
- * Define the number of ports supported and their irqs.
- */
-#define NR_PORTS 1
-#define UART_IRQ_DEFNS {UART_IRQ_NUM}
-
-#endif /* __KERNEL__ */
-#endif /* !(_MC683XX_SERIAL_H) */