summaryrefslogtreecommitdiff
path: root/drivers/net/skge.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/skge.c')
-rw-r--r--drivers/net/skge.c65
1 files changed, 34 insertions, 31 deletions
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index f15739481d62..d7c98515fdfd 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -42,7 +42,7 @@
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "0.8"
+#define DRV_VERSION "0.9"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
@@ -79,8 +79,8 @@ static const struct pci_device_id skge_id_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
- { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032) },
{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, skge_id_table);
@@ -189,7 +189,7 @@ static u32 skge_supported_modes(const struct skge_hw *hw)
{
u32 supported;
- if (iscopper(hw)) {
+ if (hw->copper) {
supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
@@ -222,7 +222,7 @@ static int skge_get_settings(struct net_device *dev,
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = skge_supported_modes(hw);
- if (iscopper(hw)) {
+ if (hw->copper) {
ecmd->port = PORT_TP;
ecmd->phy_address = hw->phy_addr;
} else
@@ -876,6 +876,9 @@ static int skge_rx_fill(struct skge_port *skge)
static void skge_link_up(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
+ LED_BLK_OFF|LED_SYNC_OFF|LED_ON);
+
netif_carrier_on(skge->netdev);
if (skge->tx_avail > MAX_SKB_FRAGS + 1)
netif_wake_queue(skge->netdev);
@@ -894,6 +897,7 @@ static void skge_link_up(struct skge_port *skge)
static void skge_link_down(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
netif_carrier_off(skge->netdev);
netif_stop_queue(skge->netdev);
@@ -1599,7 +1603,7 @@ static void yukon_init(struct skge_hw *hw, int port)
adv = PHY_AN_CSMA;
if (skge->autoneg == AUTONEG_ENABLE) {
- if (iscopper(hw)) {
+ if (hw->copper) {
if (skge->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (skge->advertising & ADVERTISED_1000baseT_Half)
@@ -1691,7 +1695,7 @@ static void yukon_mac_init(struct skge_hw *hw, int port)
/* Set hardware config mode */
reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
- reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+ reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
/* Clear GMC reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
@@ -1780,7 +1784,12 @@ static void yukon_mac_init(struct skge_hw *hw, int port)
reg &= ~GMF_RX_F_FL_ON;
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg);
- skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+ /*
+ * because Pause Packet Truncation in GMAC is not working
+ * we have to increase the Flush Threshold to 64 bytes
+ * in order to flush pause packets in Rx FIFO on Yukon-1
+ */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
/* Configure Tx MAC FIFO */
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
@@ -2670,18 +2679,6 @@ static void skge_error_irq(struct skge_hw *hw)
/* Timestamp (unused) overflow */
if (hwstatus & IS_IRQ_TIST_OV)
skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
-
- if (hwstatus & IS_IRQ_SENSOR) {
- /* no sensors on 32-bit Yukon */
- if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) {
- printk(KERN_ERR PFX "ignoring bogus sensor interrups\n");
- skge_write32(hw, B0_HWE_IMSK,
- IS_ERR_MSK & ~IS_IRQ_SENSOR);
- } else
- printk(KERN_WARNING PFX "sensor interrupt\n");
- }
-
-
}
if (hwstatus & IS_RAM_RD_PAR) {
@@ -2712,9 +2709,10 @@ static void skge_error_irq(struct skge_hw *hw)
skge_pci_clear(hw);
+ /* if error still set then just ignore it */
hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hwstatus & IS_IRQ_STAT) {
- printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n",
+ pr_debug("IRQ status %x: still set ignoring hardware errors\n",
hwstatus);
hw->intr_mask &= ~IS_HW_ERR;
}
@@ -2876,7 +2874,7 @@ static const char *skge_board_name(const struct skge_hw *hw)
static int skge_reset(struct skge_hw *hw)
{
u16 ctst;
- u8 t8, mac_cfg;
+ u8 t8, mac_cfg, pmd_type, phy_type;
int i;
ctst = skge_read16(hw, B0_CTST);
@@ -2895,18 +2893,19 @@ static int skge_reset(struct skge_hw *hw)
ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
hw->chip_id = skge_read8(hw, B2_CHIP_ID);
- hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
- hw->pmd_type = skge_read8(hw, B2_PMD_TYP);
+ phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ pmd_type = skge_read8(hw, B2_PMD_TYP);
+ hw->copper = (pmd_type == 'T' || pmd_type == '1');
switch (hw->chip_id) {
case CHIP_ID_GENESIS:
- switch (hw->phy_type) {
+ switch (phy_type) {
case SK_PHY_BCOM:
hw->phy_addr = PHY_ADDR_BCOM;
break;
default:
printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
- pci_name(hw->pdev), hw->phy_type);
+ pci_name(hw->pdev), phy_type);
return -EOPNOTSUPP;
}
break;
@@ -2914,13 +2913,10 @@ static int skge_reset(struct skge_hw *hw)
case CHIP_ID_YUKON:
case CHIP_ID_YUKON_LITE:
case CHIP_ID_YUKON_LP:
- if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S')
- hw->phy_type = SK_PHY_MARV_COPPER;
+ if (phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ hw->copper = 1;
hw->phy_addr = PHY_ADDR_MARV;
- if (!iscopper(hw))
- hw->phy_type = SK_PHY_MARV_FIBER;
-
break;
default:
@@ -2948,12 +2944,20 @@ static int skge_reset(struct skge_hw *hw)
else
hw->ram_size = t8 * 4096;
+ hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_init(hw);
else {
/* switch power to VCC (WA for VAUX problem) */
skge_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+ /* avoid boards with stuck Hardware error bits */
+ if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
+ (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
+ printk(KERN_WARNING PFX "stuck hardware sensor bit\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+
for (i = 0; i < hw->ports; i++) {
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
@@ -2994,7 +2998,6 @@ static int skge_reset(struct skge_hw *hw)
skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
skge_write32(hw, B2_IRQM_CTRL, TIM_START);
- hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
if (hw->chip_id != CHIP_ID_GENESIS)