summaryrefslogtreecommitdiff
path: root/drivers/mmc/host
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host')
-rw-r--r--drivers/mmc/host/Kconfig20
-rw-r--r--drivers/mmc/host/Makefile2
-rw-r--r--drivers/mmc/host/mmci.c37
-rw-r--r--drivers/mmc/host/mmci.h28
-rw-r--r--drivers/mmc/host/mxcmmc.c880
-rw-r--r--drivers/mmc/host/omap_hsmmc.c1242
-rw-r--r--drivers/mmc/host/pxamci.c25
-rw-r--r--drivers/mmc/host/ricoh_mmc.c8
-rw-r--r--drivers/mmc/host/s3cmci.c2
9 files changed, 2229 insertions, 15 deletions
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index dfa585f7feaf..99d4b28d52ed 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -76,6 +76,16 @@ config MMC_OMAP
If unsure, say N.
+config MMC_OMAP_HS
+ tristate "TI OMAP High Speed Multimedia Card Interface support"
+ depends on ARCH_OMAP2430 || ARCH_OMAP3
+ help
+ This selects the TI OMAP High Speed Multimedia card Interface.
+ If you have an OMAP2430 or OMAP3 board with a Multimedia Card slot,
+ say Y or M here.
+
+ If unsure, say N.
+
config MMC_WBSD
tristate "Winbond W83L51xD SD/MMC Card Interface support"
depends on ISA_DMA_API
@@ -135,6 +145,16 @@ config MMC_IMX
If unsure, say N.
+config MMC_MXC
+ tristate "Freescale i.MX2/3 Multimedia Card Interface support"
+ depends on ARCH_MXC
+ help
+ This selects the Freescale i.MX2/3 Multimedia card Interface.
+ If you have a i.MX platform with a Multimedia Card slot,
+ say Y or M here.
+
+ If unsure, say N.
+
config MMC_TIFM_SD
tristate "TI Flash Media MMC/SD Interface support (EXPERIMENTAL)"
depends on EXPERIMENTAL && PCI
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index f4853288bbb1..dedec55861d9 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -9,12 +9,14 @@ endif
obj-$(CONFIG_MMC_ARMMMCI) += mmci.o
obj-$(CONFIG_MMC_PXA) += pxamci.o
obj-$(CONFIG_MMC_IMX) += imxmmc.o
+obj-$(CONFIG_MMC_MXC) += mxcmmc.o
obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
obj-$(CONFIG_MMC_RICOH_MMC) += ricoh_mmc.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
obj-$(CONFIG_MMC_OMAP) += omap.o
+obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
obj-$(CONFIG_MMC_AT91) += at91_mci.o
obj-$(CONFIG_MMC_ATMELMCI) += atmel-mci.o
obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 1bcbdd6763ac..2909bbc8ad00 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -430,6 +430,8 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
clk = 255;
host->cclk = host->mclk / (2 * (clk + 1));
}
+ if (host->hw_designer == 0x80)
+ clk |= MCI_FCEN; /* Bug fix in ST IP block */
clk |= MCI_CLK_ENABLE;
}
@@ -440,15 +442,27 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
case MMC_POWER_OFF:
break;
case MMC_POWER_UP:
- pwr |= MCI_PWR_UP;
- break;
+ /* The ST version does not have this, fall through to POWER_ON */
+ if (host->hw_designer != 0x80) {
+ pwr |= MCI_PWR_UP;
+ break;
+ }
case MMC_POWER_ON:
pwr |= MCI_PWR_ON;
break;
}
- if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
- pwr |= MCI_ROD;
+ if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
+ if (host->hw_designer != 0x80)
+ pwr |= MCI_ROD;
+ else {
+ /*
+ * The ST Micro variant use the ROD bit for something
+ * else and only has OD (Open Drain).
+ */
+ pwr |= MCI_OD;
+ }
+ }
writel(clk, host->base + MMCICLOCK);
@@ -500,6 +514,12 @@ static int mmci_probe(struct amba_device *dev, void *id)
}
host = mmc_priv(mmc);
+ /* Bits 12 thru 19 is the designer */
+ host->hw_designer = (dev->periphid >> 12) & 0xff;
+ /* Bits 20 thru 23 is the revison */
+ host->hw_revision = (dev->periphid >> 20) & 0xf;
+ DBG(host, "designer ID = 0x%02x\n", host->hw_designer);
+ DBG(host, "revision = 0x%01x\n", host->hw_revision);
host->clk = clk_get(&dev->dev, NULL);
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
@@ -693,6 +713,15 @@ static struct amba_id mmci_ids[] = {
.id = 0x00041181,
.mask = 0x000fffff,
},
+ /* ST Micro variants */
+ {
+ .id = 0x00180180,
+ .mask = 0x00ffffff,
+ },
+ {
+ .id = 0x00280180,
+ .mask = 0x00ffffff,
+ },
{ 0, 0 },
};
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 0f39c490f022..0441bac1c0ec 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -11,13 +11,23 @@
#define MCI_PWR_OFF 0x00
#define MCI_PWR_UP 0x02
#define MCI_PWR_ON 0x03
+#define MCI_DATA2DIREN (1 << 2)
+#define MCI_CMDDIREN (1 << 3)
+#define MCI_DATA0DIREN (1 << 4)
+#define MCI_DATA31DIREN (1 << 5)
#define MCI_OD (1 << 6)
#define MCI_ROD (1 << 7)
+/* The ST Micro version does not have ROD */
+#define MCI_FBCLKEN (1 << 7)
+#define MCI_DATA74DIREN (1 << 8)
#define MMCICLOCK 0x004
#define MCI_CLK_ENABLE (1 << 8)
#define MCI_CLK_PWRSAVE (1 << 9)
#define MCI_CLK_BYPASS (1 << 10)
+#define MCI_WIDE_BUS (1 << 11)
+/* HW flow control on the ST Micro version */
+#define MCI_FCEN (1 << 13)
#define MMCIARGUMENT 0x008
#define MMCICOMMAND 0x00c
@@ -26,6 +36,10 @@
#define MCI_CPSM_INTERRUPT (1 << 8)
#define MCI_CPSM_PENDING (1 << 9)
#define MCI_CPSM_ENABLE (1 << 10)
+#define MCI_SDIO_SUSP (1 << 11)
+#define MCI_ENCMD_COMPL (1 << 12)
+#define MCI_NIEN (1 << 13)
+#define MCI_CE_ATACMD (1 << 14)
#define MMCIRESPCMD 0x010
#define MMCIRESPONSE0 0x014
@@ -39,6 +53,11 @@
#define MCI_DPSM_DIRECTION (1 << 1)
#define MCI_DPSM_MODE (1 << 2)
#define MCI_DPSM_DMAENABLE (1 << 3)
+#define MCI_DPSM_BLOCKSIZE (1 << 4)
+#define MCI_DPSM_RWSTART (1 << 8)
+#define MCI_DPSM_RWSTOP (1 << 9)
+#define MCI_DPSM_RWMOD (1 << 10)
+#define MCI_DPSM_SDIOEN (1 << 11)
#define MMCIDATACNT 0x030
#define MMCISTATUS 0x034
@@ -63,6 +82,8 @@
#define MCI_RXFIFOEMPTY (1 << 19)
#define MCI_TXDATAAVLBL (1 << 20)
#define MCI_RXDATAAVLBL (1 << 21)
+#define MCI_SDIOIT (1 << 22)
+#define MCI_CEATAEND (1 << 23)
#define MMCICLEAR 0x038
#define MCI_CMDCRCFAILCLR (1 << 0)
@@ -75,6 +96,8 @@
#define MCI_CMDSENTCLR (1 << 7)
#define MCI_DATAENDCLR (1 << 8)
#define MCI_DATABLOCKENDCLR (1 << 10)
+#define MCI_SDIOITC (1 << 22)
+#define MCI_CEATAENDC (1 << 23)
#define MMCIMASK0 0x03c
#define MCI_CMDCRCFAILMASK (1 << 0)
@@ -98,6 +121,8 @@
#define MCI_RXFIFOEMPTYMASK (1 << 19)
#define MCI_TXDATAAVLBLMASK (1 << 20)
#define MCI_RXDATAAVLBLMASK (1 << 21)
+#define MCI_SDIOITMASK (1 << 22)
+#define MCI_CEATAENDMASK (1 << 23)
#define MMCIMASK1 0x040
#define MMCIFIFOCNT 0x048
@@ -136,6 +161,9 @@ struct mmci_host {
u32 pwr;
struct mmc_platform_data *plat;
+ u8 hw_designer;
+ u8 hw_revision:4;
+
struct timer_list timer;
unsigned int oldstat;
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
new file mode 100644
index 000000000000..dda0be4e25dc
--- /dev/null
+++ b/drivers/mmc/host/mxcmmc.c
@@ -0,0 +1,880 @@
+/*
+ * linux/drivers/mmc/host/mxcmmc.c - Freescale i.MX MMCI driver
+ *
+ * This is a driver for the SDHC controller found in Freescale MX2/MX3
+ * SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
+ * Unlike the hardware found on MX1, this hardware just works and does
+ * not need all the quirks found in imxmmc.c, hence the seperate driver.
+ *
+ * Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
+ * Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
+ *
+ * derived from pxamci.c by Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/blkdev.h>
+#include <linux/dma-mapping.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <asm/dma.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+#include <mach/mmc.h>
+
+#ifdef CONFIG_ARCH_MX2
+#include <mach/dma-mx1-mx2.h>
+#define HAS_DMA
+#endif
+
+#define DRIVER_NAME "imx-mmc"
+
+#define MMC_REG_STR_STP_CLK 0x00
+#define MMC_REG_STATUS 0x04
+#define MMC_REG_CLK_RATE 0x08
+#define MMC_REG_CMD_DAT_CONT 0x0C
+#define MMC_REG_RES_TO 0x10
+#define MMC_REG_READ_TO 0x14
+#define MMC_REG_BLK_LEN 0x18
+#define MMC_REG_NOB 0x1C
+#define MMC_REG_REV_NO 0x20
+#define MMC_REG_INT_CNTR 0x24
+#define MMC_REG_CMD 0x28
+#define MMC_REG_ARG 0x2C
+#define MMC_REG_RES_FIFO 0x34
+#define MMC_REG_BUFFER_ACCESS 0x38
+
+#define STR_STP_CLK_RESET (1 << 3)
+#define STR_STP_CLK_START_CLK (1 << 1)
+#define STR_STP_CLK_STOP_CLK (1 << 0)
+
+#define STATUS_CARD_INSERTION (1 << 31)
+#define STATUS_CARD_REMOVAL (1 << 30)
+#define STATUS_YBUF_EMPTY (1 << 29)
+#define STATUS_XBUF_EMPTY (1 << 28)
+#define STATUS_YBUF_FULL (1 << 27)
+#define STATUS_XBUF_FULL (1 << 26)
+#define STATUS_BUF_UND_RUN (1 << 25)
+#define STATUS_BUF_OVFL (1 << 24)
+#define STATUS_SDIO_INT_ACTIVE (1 << 14)
+#define STATUS_END_CMD_RESP (1 << 13)
+#define STATUS_WRITE_OP_DONE (1 << 12)
+#define STATUS_DATA_TRANS_DONE (1 << 11)
+#define STATUS_READ_OP_DONE (1 << 11)
+#define STATUS_WR_CRC_ERROR_CODE_MASK (3 << 10)
+#define STATUS_CARD_BUS_CLK_RUN (1 << 8)
+#define STATUS_BUF_READ_RDY (1 << 7)
+#define STATUS_BUF_WRITE_RDY (1 << 6)
+#define STATUS_RESP_CRC_ERR (1 << 5)
+#define STATUS_CRC_READ_ERR (1 << 3)
+#define STATUS_CRC_WRITE_ERR (1 << 2)
+#define STATUS_TIME_OUT_RESP (1 << 1)
+#define STATUS_TIME_OUT_READ (1 << 0)
+#define STATUS_ERR_MASK 0x2f
+
+#define CMD_DAT_CONT_CMD_RESP_LONG_OFF (1 << 12)
+#define CMD_DAT_CONT_STOP_READWAIT (1 << 11)
+#define CMD_DAT_CONT_START_READWAIT (1 << 10)
+#define CMD_DAT_CONT_BUS_WIDTH_4 (2 << 8)
+#define CMD_DAT_CONT_INIT (1 << 7)
+#define CMD_DAT_CONT_WRITE (1 << 4)
+#define CMD_DAT_CONT_DATA_ENABLE (1 << 3)
+#define CMD_DAT_CONT_RESPONSE_48BIT_CRC (1 << 0)
+#define CMD_DAT_CONT_RESPONSE_136BIT (2 << 0)
+#define CMD_DAT_CONT_RESPONSE_48BIT (3 << 0)
+
+#define INT_SDIO_INT_WKP_EN (1 << 18)
+#define INT_CARD_INSERTION_WKP_EN (1 << 17)
+#define INT_CARD_REMOVAL_WKP_EN (1 << 16)
+#define INT_CARD_INSERTION_EN (1 << 15)
+#define INT_CARD_REMOVAL_EN (1 << 14)
+#define INT_SDIO_IRQ_EN (1 << 13)
+#define INT_DAT0_EN (1 << 12)
+#define INT_BUF_READ_EN (1 << 4)
+#define INT_BUF_WRITE_EN (1 << 3)
+#define INT_END_CMD_RES_EN (1 << 2)
+#define INT_WRITE_OP_DONE_EN (1 << 1)
+#define INT_READ_OP_EN (1 << 0)
+
+struct mxcmci_host {
+ struct mmc_host *mmc;
+ struct resource *res;
+ void __iomem *base;
+ int irq;
+ int detect_irq;
+ int dma;
+ int do_dma;
+ unsigned int power_mode;
+ struct imxmmc_platform_data *pdata;
+
+ struct mmc_request *req;
+ struct mmc_command *cmd;
+ struct mmc_data *data;
+
+ unsigned int dma_nents;
+ unsigned int datasize;
+ unsigned int dma_dir;
+
+ u16 rev_no;
+ unsigned int cmdat;
+
+ struct clk *clk;
+
+ int clock;
+
+ struct work_struct datawork;
+};
+
+static inline int mxcmci_use_dma(struct mxcmci_host *host)
+{
+ return host->do_dma;
+}
+
+static void mxcmci_softreset(struct mxcmci_host *host)
+{
+ int i;
+
+ /* reset sequence */
+ writew(STR_STP_CLK_RESET, host->base + MMC_REG_STR_STP_CLK);
+ writew(STR_STP_CLK_RESET | STR_STP_CLK_START_CLK,
+ host->base + MMC_REG_STR_STP_CLK);
+
+ for (i = 0; i < 8; i++)
+ writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK);
+
+ writew(0xff, host->base + MMC_REG_RES_TO);
+}
+
+static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
+{
+ unsigned int nob = data->blocks;
+ unsigned int blksz = data->blksz;
+ unsigned int datasize = nob * blksz;
+#ifdef HAS_DMA
+ struct scatterlist *sg;
+ int i;
+#endif
+ if (data->flags & MMC_DATA_STREAM)
+ nob = 0xffff;
+
+ host->data = data;
+ data->bytes_xfered = 0;
+
+ writew(nob, host->base + MMC_REG_NOB);
+ writew(blksz, host->base + MMC_REG_BLK_LEN);
+ host->datasize = datasize;
+
+#ifdef HAS_DMA
+ for_each_sg(data->sg, sg, data->sg_len, i) {
+ if (sg->offset & 3 || sg->length & 3) {
+ host->do_dma = 0;
+ return;
+ }
+ }
+
+ if (data->flags & MMC_DATA_READ) {
+ host->dma_dir = DMA_FROM_DEVICE;
+ host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+ data->sg_len, host->dma_dir);
+
+ imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
+ host->res->start + MMC_REG_BUFFER_ACCESS,
+ DMA_MODE_READ);
+ } else {
+ host->dma_dir = DMA_TO_DEVICE;
+ host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+ data->sg_len, host->dma_dir);
+
+ imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
+ host->res->start + MMC_REG_BUFFER_ACCESS,
+ DMA_MODE_WRITE);
+ }
+
+ wmb();
+
+ imx_dma_enable(host->dma);
+#endif /* HAS_DMA */
+}
+
+static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
+ unsigned int cmdat)
+{
+ WARN_ON(host->cmd != NULL);
+ host->cmd = cmd;
+
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_R1: /* short CRC, OPCODE */
+ case MMC_RSP_R1B:/* short CRC, OPCODE, BUSY */
+ cmdat |= CMD_DAT_CONT_RESPONSE_48BIT_CRC;
+ break;
+ case MMC_RSP_R2: /* long 136 bit + CRC */
+ cmdat |= CMD_DAT_CONT_RESPONSE_136BIT;
+ break;
+ case MMC_RSP_R3: /* short */
+ cmdat |= CMD_DAT_CONT_RESPONSE_48BIT;
+ break;
+ case MMC_RSP_NONE:
+ break;
+ default:
+ dev_err(mmc_dev(host->mmc), "unhandled response type 0x%x\n",
+ mmc_resp_type(cmd));
+ cmd->error = -EINVAL;
+ return -EINVAL;
+ }
+
+ if (mxcmci_use_dma(host))
+ writel(INT_READ_OP_EN | INT_WRITE_OP_DONE_EN |
+ INT_END_CMD_RES_EN,
+ host->base + MMC_REG_INT_CNTR);
+ else
+ writel(INT_END_CMD_RES_EN, host->base + MMC_REG_INT_CNTR);
+
+ writew(cmd->opcode, host->base + MMC_REG_CMD);
+ writel(cmd->arg, host->base + MMC_REG_ARG);
+ writew(cmdat, host->base + MMC_REG_CMD_DAT_CONT);
+
+ return 0;
+}
+
+static void mxcmci_finish_request(struct mxcmci_host *host,
+ struct mmc_request *req)
+{
+ writel(0, host->base + MMC_REG_INT_CNTR);
+
+ host->req = NULL;
+ host->cmd = NULL;
+ host->data = NULL;
+
+ mmc_request_done(host->mmc, req);
+}
+
+static int mxcmci_finish_data(struct mxcmci_host *host, unsigned int stat)
+{
+ struct mmc_data *data = host->data;
+ int data_error;
+
+#ifdef HAS_DMA
+ if (mxcmci_use_dma(host)) {
+ imx_dma_disable(host->dma);
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_nents,
+ host->dma_dir);
+ }
+#endif
+
+ if (stat & STATUS_ERR_MASK) {
+ dev_dbg(mmc_dev(host->mmc), "request failed. status: 0x%08x\n",
+ stat);
+ if (stat & STATUS_CRC_READ_ERR) {
+ data->error = -EILSEQ;
+ } else if (stat & STATUS_CRC_WRITE_ERR) {
+ u32 err_code = (stat >> 9) & 0x3;
+ if (err_code == 2) /* No CRC response */
+ data->error = -ETIMEDOUT;
+ else
+ data->error = -EILSEQ;
+ } else if (stat & STATUS_TIME_OUT_READ) {
+ data->error = -ETIMEDOUT;
+ } else {
+ data->error = -EIO;
+ }
+ } else {
+ data->bytes_xfered = host->datasize;
+ }
+
+ data_error = data->error;
+
+ host->data = NULL;
+
+ return data_error;
+}
+
+static void mxcmci_read_response(struct mxcmci_host *host, unsigned int stat)
+{
+ struct mmc_command *cmd = host->cmd;
+ int i;
+ u32 a, b, c;
+
+ if (!cmd)
+ return;
+
+ if (stat & STATUS_TIME_OUT_RESP) {
+ dev_dbg(mmc_dev(host->mmc), "CMD TIMEOUT\n");
+ cmd->error = -ETIMEDOUT;
+ } else if (stat & STATUS_RESP_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
+ dev_dbg(mmc_dev(host->mmc), "cmd crc error\n");
+ cmd->error = -EILSEQ;
+ }
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ for (i = 0; i < 4; i++) {
+ a = readw(host->base + MMC_REG_RES_FIFO);
+ b = readw(host->base + MMC_REG_RES_FIFO);
+ cmd->resp[i] = a << 16 | b;
+ }
+ } else {
+ a = readw(host->base + MMC_REG_RES_FIFO);
+ b = readw(host->base + MMC_REG_RES_FIFO);
+ c = readw(host->base + MMC_REG_RES_FIFO);
+ cmd->resp[0] = a << 24 | b << 8 | c >> 8;
+ }
+ }
+}
+
+static int mxcmci_poll_status(struct mxcmci_host *host, u32 mask)
+{
+ u32 stat;
+ unsigned long timeout = jiffies + HZ;
+
+ do {
+ stat = readl(host->base + MMC_REG_STATUS);
+ if (stat & STATUS_ERR_MASK)
+ return stat;
+ if (time_after(jiffies, timeout))
+ return STATUS_TIME_OUT_READ;
+ if (stat & mask)
+ return 0;
+ cpu_relax();
+ } while (1);
+}
+
+static int mxcmci_pull(struct mxcmci_host *host, void *_buf, int bytes)
+{
+ unsigned int stat;
+ u32 *buf = _buf;
+
+ while (bytes > 3) {
+ stat = mxcmci_poll_status(host,
+ STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
+ if (stat)
+ return stat;
+ *buf++ = readl(host->base + MMC_REG_BUFFER_ACCESS);
+ bytes -= 4;
+ }
+
+ if (bytes) {
+ u8 *b = (u8 *)buf;
+ u32 tmp;
+
+ stat = mxcmci_poll_status(host,
+ STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
+ if (stat)
+ return stat;
+ tmp = readl(host->base + MMC_REG_BUFFER_ACCESS);
+ memcpy(b, &tmp, bytes);
+ }
+
+ return 0;
+}
+
+static int mxcmci_push(struct mxcmci_host *host, void *_buf, int bytes)
+{
+ unsigned int stat;
+ u32 *buf = _buf;
+
+ while (bytes > 3) {
+ stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+ if (stat)
+ return stat;
+ writel(*buf++, host->base + MMC_REG_BUFFER_ACCESS);
+ bytes -= 4;
+ }
+
+ if (bytes) {
+ u8 *b = (u8 *)buf;
+ u32 tmp;
+
+ stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+ if (stat)
+ return stat;
+
+ memcpy(&tmp, b, bytes);
+ writel(tmp, host->base + MMC_REG_BUFFER_ACCESS);
+ }
+
+ stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+ if (stat)
+ return stat;
+
+ return 0;
+}
+
+static int mxcmci_transfer_data(struct mxcmci_host *host)
+{
+ struct mmc_data *data = host->req->data;
+ struct scatterlist *sg;
+ int stat, i;
+
+ host->datasize = 0;
+
+ host->data = data;
+ host->datasize = 0;
+
+ if (data->flags & MMC_DATA_READ) {
+ for_each_sg(data->sg, sg, data->sg_len, i) {
+ stat = mxcmci_pull(host, sg_virt(sg), sg->length);
+ if (stat)
+ return stat;
+ host->datasize += sg->length;
+ }
+ } else {
+ for_each_sg(data->sg, sg, data->sg_len, i) {
+ stat = mxcmci_push(host, sg_virt(sg), sg->length);
+ if (stat)
+ return stat;
+ host->datasize += sg->length;
+ }
+ stat = mxcmci_poll_status(host, STATUS_WRITE_OP_DONE);
+ if (stat)
+ return stat;
+ }
+ return 0;
+}
+
+static void mxcmci_datawork(struct work_struct *work)
+{
+ struct mxcmci_host *host = container_of(work, struct mxcmci_host,
+ datawork);
+ int datastat = mxcmci_transfer_data(host);
+ mxcmci_finish_data(host, datastat);
+
+ if (host->req->stop) {
+ if (mxcmci_start_cmd(host, host->req->stop, 0)) {
+ mxcmci_finish_request(host, host->req);
+ return;
+ }
+ } else {
+ mxcmci_finish_request(host, host->req);
+ }
+}
+
+#ifdef HAS_DMA
+static void mxcmci_data_done(struct mxcmci_host *host, unsigned int stat)
+{
+ struct mmc_data *data = host->data;
+ int data_error;
+
+ if (!data)
+ return;
+
+ data_error = mxcmci_finish_data(host, stat);
+
+ mxcmci_read_response(host, stat);
+ host->cmd = NULL;
+
+ if (host->req->stop) {
+ if (mxcmci_start_cmd(host, host->req->stop, 0)) {
+ mxcmci_finish_request(host, host->req);
+ return;
+ }
+ } else {
+ mxcmci_finish_request(host, host->req);
+ }
+}
+#endif /* HAS_DMA */
+
+static void mxcmci_cmd_done(struct mxcmci_host *host, unsigned int stat)
+{
+ mxcmci_read_response(host, stat);
+ host->cmd = NULL;
+
+ if (!host->data && host->req) {
+ mxcmci_finish_request(host, host->req);
+ return;
+ }
+
+ /* For the DMA case the DMA engine handles the data transfer
+ * automatically. For non DMA we have to to it ourselves.
+ * Don't do it in interrupt context though.
+ */
+ if (!mxcmci_use_dma(host) && host->data)
+ schedule_work(&host->datawork);
+
+}
+
+static irqreturn_t mxcmci_irq(int irq, void *devid)
+{
+ struct mxcmci_host *host = devid;
+ u32 stat;
+
+ stat = readl(host->base + MMC_REG_STATUS);
+ writel(stat, host->base + MMC_REG_STATUS);
+
+ dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat);
+
+ if (stat & STATUS_END_CMD_RESP)
+ mxcmci_cmd_done(host, stat);
+#ifdef HAS_DMA
+ if (mxcmci_use_dma(host) &&
+ (stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE)))
+ mxcmci_data_done(host, stat);
+#endif
+ return IRQ_HANDLED;
+}
+
+static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+ struct mxcmci_host *host = mmc_priv(mmc);
+ unsigned int cmdat = host->cmdat;
+
+ WARN_ON(host->req != NULL);
+
+ host->req = req;
+ host->cmdat &= ~CMD_DAT_CONT_INIT;
+#ifdef HAS_DMA
+ host->do_dma = 1;
+#endif
+ if (req->data) {
+ mxcmci_setup_data(host, req->data);
+
+ cmdat |= CMD_DAT_CONT_DATA_ENABLE;
+
+ if (req->data->flags & MMC_DATA_WRITE)
+ cmdat |= CMD_DAT_CONT_WRITE;
+ }
+
+ if (mxcmci_start_cmd(host, req->cmd, cmdat))
+ mxcmci_finish_request(host, req);
+}
+
+static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios)
+{
+ unsigned int divider;
+ int prescaler = 0;
+ unsigned int clk_in = clk_get_rate(host->clk);
+
+ while (prescaler <= 0x800) {
+ for (divider = 1; divider <= 0xF; divider++) {
+ int x;
+
+ x = (clk_in / (divider + 1));
+
+ if (prescaler)
+ x /= (prescaler * 2);
+
+ if (x <= clk_ios)
+ break;
+ }
+ if (divider < 0x10)
+ break;
+
+ if (prescaler == 0)
+ prescaler = 1;
+ else
+ prescaler <<= 1;
+ }
+
+ writew((prescaler << 4) | divider, host->base + MMC_REG_CLK_RATE);
+
+ dev_dbg(mmc_dev(host->mmc), "scaler: %d divider: %d in: %d out: %d\n",
+ prescaler, divider, clk_in, clk_ios);
+}
+
+static void mxcmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct mxcmci_host *host = mmc_priv(mmc);
+#ifdef HAS_DMA
+ unsigned int blen;
+ /*
+ * use burstlen of 64 in 4 bit mode (--> reg value 0)
+ * use burstlen of 16 in 1 bit mode (--> reg value 16)
+ */
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ blen = 0;
+ else
+ blen = 16;
+
+ imx_dma_config_burstlen(host->dma, blen);
+#endif
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ host->cmdat |= CMD_DAT_CONT_BUS_WIDTH_4;
+ else
+ host->cmdat &= ~CMD_DAT_CONT_BUS_WIDTH_4;
+
+ if (host->power_mode != ios->power_mode) {
+ if (host->pdata && host->pdata->setpower)
+ host->pdata->setpower(mmc_dev(mmc), ios->vdd);
+ host->power_mode = ios->power_mode;
+ if (ios->power_mode == MMC_POWER_ON)
+ host->cmdat |= CMD_DAT_CONT_INIT;
+ }
+
+ if (ios->clock) {
+ mxcmci_set_clk_rate(host, ios->clock);
+ writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK);
+ } else {
+ writew(STR_STP_CLK_STOP_CLK, host->base + MMC_REG_STR_STP_CLK);
+ }
+
+ host->clock = ios->clock;
+}
+
+static irqreturn_t mxcmci_detect_irq(int irq, void *data)
+{
+ struct mmc_host *mmc = data;
+
+ dev_dbg(mmc_dev(mmc), "%s\n", __func__);
+
+ mmc_detect_change(mmc, msecs_to_jiffies(250));
+ return IRQ_HANDLED;
+}
+
+static int mxcmci_get_ro(struct mmc_host *mmc)
+{
+ struct mxcmci_host *host = mmc_priv(mmc);
+
+ if (host->pdata && host->pdata->get_ro)
+ return !!host->pdata->get_ro(mmc_dev(mmc));
+ /*
+ * Board doesn't support read only detection; let the mmc core
+ * decide what to do.
+ */
+ return -ENOSYS;
+}
+
+
+static const struct mmc_host_ops mxcmci_ops = {
+ .request = mxcmci_request,
+ .set_ios = mxcmci_set_ios,
+ .get_ro = mxcmci_get_ro,
+};
+
+static int mxcmci_probe(struct platform_device *pdev)
+{
+ struct mmc_host *mmc;
+ struct mxcmci_host *host = NULL;
+ struct resource *r;
+ int ret = 0, irq;
+
+ printk(KERN_INFO "i.MX SDHC driver\n");
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (!r || irq < 0)
+ return -EINVAL;
+
+ r = request_mem_region(r->start, resource_size(r), pdev->name);
+ if (!r)
+ return -EBUSY;
+
+ mmc = mmc_alloc_host(sizeof(struct mxcmci_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto out_release_mem;
+ }
+
+ mmc->ops = &mxcmci_ops;
+ mmc->caps = MMC_CAP_4_BIT_DATA;
+
+ /* MMC core transfer sizes tunable parameters */
+ mmc->max_hw_segs = 64;
+ mmc->max_phys_segs = 64;
+ mmc->max_blk_size = 2048;
+ mmc->max_blk_count = 65535;
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_seg_size;
+
+ host = mmc_priv(mmc);
+ host->base = ioremap(r->start, resource_size(r));
+ if (!host->base) {
+ ret = -ENOMEM;
+ goto out_free;
+ }
+
+ host->mmc = mmc;
+ host->pdata = pdev->dev.platform_data;
+
+ if (host->pdata && host->pdata->ocr_avail)
+ mmc->ocr_avail = host->pdata->ocr_avail;
+ else
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+ host->res = r;
+ host->irq = irq;
+
+ host->clk = clk_get(&pdev->dev, "sdhc_clk");
+ if (IS_ERR(host->clk)) {
+ ret = PTR_ERR(host->clk);
+ goto out_iounmap;
+ }
+ clk_enable(host->clk);
+
+ mxcmci_softreset(host);
+
+ host->rev_no = readw(host->base + MMC_REG_REV_NO);
+ if (host->rev_no != 0x400) {
+ ret = -ENODEV;
+ dev_err(mmc_dev(host->mmc), "wrong rev.no. 0x%08x. aborting.\n",
+ host->rev_no);
+ goto out_clk_put;
+ }
+
+ mmc->f_min = clk_get_rate(host->clk) >> 7;
+ mmc->f_max = clk_get_rate(host->clk) >> 1;
+
+ /* recommended in data sheet */
+ writew(0x2db4, host->base + MMC_REG_READ_TO);
+
+ writel(0, host->base + MMC_REG_INT_CNTR);
+
+#ifdef HAS_DMA
+ host->dma = imx_dma_request_by_prio(DRIVER_NAME, DMA_PRIO_LOW);
+ if (host->dma < 0) {
+ dev_err(mmc_dev(host->mmc), "imx_dma_request_by_prio failed\n");
+ ret = -EBUSY;
+ goto out_clk_put;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (!r) {
+ ret = -EINVAL;
+ goto out_free_dma;
+ }
+
+ ret = imx_dma_config_channel(host->dma,
+ IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_FIFO,
+ IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_LINEAR,
+ r->start, 0);
+ if (ret) {
+ dev_err(mmc_dev(host->mmc), "failed to config DMA channel\n");
+ goto out_free_dma;
+ }
+#endif
+ INIT_WORK(&host->datawork, mxcmci_datawork);
+
+ ret = request_irq(host->irq, mxcmci_irq, 0, DRIVER_NAME, host);
+ if (ret)
+ goto out_free_dma;
+
+ platform_set_drvdata(pdev, mmc);
+
+ if (host->pdata && host->pdata->init) {
+ ret = host->pdata->init(&pdev->dev, mxcmci_detect_irq,
+ host->mmc);
+ if (ret)
+ goto out_free_irq;
+ }
+
+ mmc_add_host(mmc);
+
+ return 0;
+
+out_free_irq:
+ free_irq(host->irq, host);
+out_free_dma:
+#ifdef HAS_DMA
+ imx_dma_free(host->dma);
+#endif
+out_clk_put:
+ clk_disable(host->clk);
+ clk_put(host->clk);
+out_iounmap:
+ iounmap(host->base);
+out_free:
+ mmc_free_host(mmc);
+out_release_mem:
+ release_mem_region(host->res->start, resource_size(host->res));
+ return ret;
+}
+
+static int mxcmci_remove(struct platform_device *pdev)
+{
+ struct mmc_host *mmc = platform_get_drvdata(pdev);
+ struct mxcmci_host *host = mmc_priv(mmc);
+
+ platform_set_drvdata(pdev, NULL);
+
+ mmc_remove_host(mmc);
+
+ if (host->pdata && host->pdata->exit)
+ host->pdata->exit(&pdev->dev, mmc);
+
+ free_irq(host->irq, host);
+ iounmap(host->base);
+#ifdef HAS_DMA
+ imx_dma_free(host->dma);
+#endif
+ clk_disable(host->clk);
+ clk_put(host->clk);
+
+ release_mem_region(host->res->start, resource_size(host->res));
+ release_resource(host->res);
+
+ mmc_free_host(mmc);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int mxcmci_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct mmc_host *mmc = platform_get_drvdata(dev);
+ int ret = 0;
+
+ if (mmc)
+ ret = mmc_suspend_host(mmc, state);
+
+ return ret;
+}
+
+static int mxcmci_resume(struct platform_device *dev)
+{
+ struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mxcmci_host *host;
+ int ret = 0;
+
+ if (mmc) {
+ host = mmc_priv(mmc);
+ ret = mmc_resume_host(mmc);
+ }
+
+ return ret;
+}
+#else
+#define mxcmci_suspend NULL
+#define mxcmci_resume NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver mxcmci_driver = {
+ .probe = mxcmci_probe,
+ .remove = mxcmci_remove,
+ .suspend = mxcmci_suspend,
+ .resume = mxcmci_resume,
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ }
+};
+
+static int __init mxcmci_init(void)
+{
+ return platform_driver_register(&mxcmci_driver);
+}
+
+static void __exit mxcmci_exit(void)
+{
+ platform_driver_unregister(&mxcmci_driver);
+}
+
+module_init(mxcmci_init);
+module_exit(mxcmci_exit);
+
+MODULE_DESCRIPTION("i.MX Multimedia Card Interface Driver");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-mmc");
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
new file mode 100644
index 000000000000..db37490f67ec
--- /dev/null
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -0,0 +1,1242 @@
+/*
+ * drivers/mmc/host/omap_hsmmc.c
+ *
+ * Driver for OMAP2430/3430 MMC controller.
+ *
+ * Copyright (C) 2007 Texas Instruments.
+ *
+ * Authors:
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ * Madhusudhan <madhu.cr@ti.com>
+ * Mohit Jalori <mjalori@ti.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+#include <linux/timer.h>
+#include <linux/clk.h>
+#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/semaphore.h>
+#include <mach/dma.h>
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/mmc.h>
+#include <mach/cpu.h>
+
+/* OMAP HSMMC Host Controller Registers */
+#define OMAP_HSMMC_SYSCONFIG 0x0010
+#define OMAP_HSMMC_CON 0x002C
+#define OMAP_HSMMC_BLK 0x0104
+#define OMAP_HSMMC_ARG 0x0108
+#define OMAP_HSMMC_CMD 0x010C
+#define OMAP_HSMMC_RSP10 0x0110
+#define OMAP_HSMMC_RSP32 0x0114
+#define OMAP_HSMMC_RSP54 0x0118
+#define OMAP_HSMMC_RSP76 0x011C
+#define OMAP_HSMMC_DATA 0x0120
+#define OMAP_HSMMC_HCTL 0x0128
+#define OMAP_HSMMC_SYSCTL 0x012C
+#define OMAP_HSMMC_STAT 0x0130
+#define OMAP_HSMMC_IE 0x0134
+#define OMAP_HSMMC_ISE 0x0138
+#define OMAP_HSMMC_CAPA 0x0140
+
+#define VS18 (1 << 26)
+#define VS30 (1 << 25)
+#define SDVS18 (0x5 << 9)
+#define SDVS30 (0x6 << 9)
+#define SDVSCLR 0xFFFFF1FF
+#define SDVSDET 0x00000400
+#define AUTOIDLE 0x1
+#define SDBP (1 << 8)
+#define DTO 0xe
+#define ICE 0x1
+#define ICS 0x2
+#define CEN (1 << 2)
+#define CLKD_MASK 0x0000FFC0
+#define CLKD_SHIFT 6
+#define DTO_MASK 0x000F0000
+#define DTO_SHIFT 16
+#define INT_EN_MASK 0x307F0033
+#define INIT_STREAM (1 << 1)
+#define DP_SELECT (1 << 21)
+#define DDIR (1 << 4)
+#define DMA_EN 0x1
+#define MSBS (1 << 5)
+#define BCE (1 << 1)
+#define FOUR_BIT (1 << 1)
+#define CC 0x1
+#define TC 0x02
+#define OD 0x1
+#define ERR (1 << 15)
+#define CMD_TIMEOUT (1 << 16)
+#define DATA_TIMEOUT (1 << 20)
+#define CMD_CRC (1 << 17)
+#define DATA_CRC (1 << 21)
+#define CARD_ERR (1 << 28)
+#define STAT_CLEAR 0xFFFFFFFF
+#define INIT_STREAM_CMD 0x00000000
+#define DUAL_VOLT_OCR_BIT 7
+#define SRC (1 << 25)
+#define SRD (1 << 26)
+
+/*
+ * FIXME: Most likely all the data using these _DEVID defines should come
+ * from the platform_data, or implemented in controller and slot specific
+ * functions.
+ */
+#define OMAP_MMC1_DEVID 0
+#define OMAP_MMC2_DEVID 1
+
+#define OMAP_MMC_DATADIR_NONE 0
+#define OMAP_MMC_DATADIR_READ 1
+#define OMAP_MMC_DATADIR_WRITE 2
+#define MMC_TIMEOUT_MS 20
+#define OMAP_MMC_MASTER_CLOCK 96000000
+#define DRIVER_NAME "mmci-omap-hs"
+
+/*
+ * One controller can have multiple slots, like on some omap boards using
+ * omap.c controller driver. Luckily this is not currently done on any known
+ * omap_hsmmc.c device.
+ */
+#define mmc_slot(host) (host->pdata->slots[host->slot_id])
+
+/*
+ * MMC Host controller read/write API's
+ */
+#define OMAP_HSMMC_READ(base, reg) \
+ __raw_readl((base) + OMAP_HSMMC_##reg)
+
+#define OMAP_HSMMC_WRITE(base, reg, val) \
+ __raw_writel((val), (base) + OMAP_HSMMC_##reg)
+
+struct mmc_omap_host {
+ struct device *dev;
+ struct mmc_host *mmc;
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_data *data;
+ struct clk *fclk;
+ struct clk *iclk;
+ struct clk *dbclk;
+ struct semaphore sem;
+ struct work_struct mmc_carddetect_work;
+ void __iomem *base;
+ resource_size_t mapbase;
+ unsigned int id;
+ unsigned int dma_len;
+ unsigned int dma_dir;
+ unsigned char bus_mode;
+ unsigned char datadir;
+ u32 *buffer;
+ u32 bytesleft;
+ int suspended;
+ int irq;
+ int carddetect;
+ int use_dma, dma_ch;
+ int initstr;
+ int slot_id;
+ int dbclk_enabled;
+ struct omap_mmc_platform_data *pdata;
+};
+
+/*
+ * Stop clock to the card
+ */
+static void omap_mmc_stop_clock(struct mmc_omap_host *host)
+{
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
+ if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
+ dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stoped\n");
+}
+
+/*
+ * Send init stream sequence to card
+ * before sending IDLE command
+ */
+static void send_init_stream(struct mmc_omap_host *host)
+{
+ int reg = 0;
+ unsigned long timeout;
+
+ disable_irq(host->irq);
+ OMAP_HSMMC_WRITE(host->base, CON,
+ OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM);
+ OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD);
+
+ timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+ while ((reg != CC) && time_before(jiffies, timeout))
+ reg = OMAP_HSMMC_READ(host->base, STAT) & CC;
+
+ OMAP_HSMMC_WRITE(host->base, CON,
+ OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM);
+ enable_irq(host->irq);
+}
+
+static inline
+int mmc_omap_cover_is_closed(struct mmc_omap_host *host)
+{
+ int r = 1;
+
+ if (host->pdata->slots[host->slot_id].get_cover_state)
+ r = host->pdata->slots[host->slot_id].get_cover_state(host->dev,
+ host->slot_id);
+ return r;
+}
+
+static ssize_t
+mmc_omap_show_cover_switch(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+ struct mmc_omap_host *host = mmc_priv(mmc);
+
+ return sprintf(buf, "%s\n", mmc_omap_cover_is_closed(host) ? "closed" :
+ "open");
+}
+
+static DEVICE_ATTR(cover_switch, S_IRUGO, mmc_omap_show_cover_switch, NULL);
+
+static ssize_t
+mmc_omap_show_slot_name(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+ struct mmc_omap_host *host = mmc_priv(mmc);
+ struct omap_mmc_slot_data slot = host->pdata->slots[host->slot_id];
+
+ return sprintf(buf, "slot:%s\n", slot.name);
+}
+
+static DEVICE_ATTR(slot_name, S_IRUGO, mmc_omap_show_slot_name, NULL);
+
+/*
+ * Configure the response type and send the cmd.
+ */
+static void
+mmc_omap_start_command(struct mmc_omap_host *host, struct mmc_command *cmd,
+ struct mmc_data *data)
+{
+ int cmdreg = 0, resptype = 0, cmdtype = 0;
+
+ dev_dbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n",
+ mmc_hostname(host->mmc), cmd->opcode, cmd->arg);
+ host->cmd = cmd;
+
+ /*
+ * Clear status bits and enable interrupts
+ */
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_WRITE(host->base, ISE, INT_EN_MASK);
+ OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136)
+ resptype = 1;
+ else
+ resptype = 2;
+ }
+
+ /*
+ * Unlike OMAP1 controller, the cmdtype does not seem to be based on
+ * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
+ * a val of 0x3, rest 0x0.
+ */
+ if (cmd == host->mrq->stop)
+ cmdtype = 0x3;
+
+ cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
+
+ if (data) {
+ cmdreg |= DP_SELECT | MSBS | BCE;
+ if (data->flags & MMC_DATA_READ)
+ cmdreg |= DDIR;
+ else
+ cmdreg &= ~(DDIR);
+ }
+
+ if (host->use_dma)
+ cmdreg |= DMA_EN;
+
+ OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg);
+ OMAP_HSMMC_WRITE(host->base, CMD, cmdreg);
+}
+
+/*
+ * Notify the transfer complete to MMC core
+ */
+static void
+mmc_omap_xfer_done(struct mmc_omap_host *host, struct mmc_data *data)
+{
+ host->data = NULL;
+
+ if (host->use_dma && host->dma_ch != -1)
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_len,
+ host->dma_dir);
+
+ host->datadir = OMAP_MMC_DATADIR_NONE;
+
+ if (!data->error)
+ data->bytes_xfered += data->blocks * (data->blksz);
+ else
+ data->bytes_xfered = 0;
+
+ if (!data->stop) {
+ host->mrq = NULL;
+ mmc_request_done(host->mmc, data->mrq);
+ return;
+ }
+ mmc_omap_start_command(host, data->stop, NULL);
+}
+
+/*
+ * Notify the core about command completion
+ */
+static void
+mmc_omap_cmd_done(struct mmc_omap_host *host, struct mmc_command *cmd)
+{
+ host->cmd = NULL;
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ /* response type 2 */
+ cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10);
+ cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32);
+ cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54);
+ cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76);
+ } else {
+ /* response types 1, 1b, 3, 4, 5, 6 */
+ cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10);
+ }
+ }
+ if (host->data == NULL || cmd->error) {
+ host->mrq = NULL;
+ mmc_request_done(host->mmc, cmd->mrq);
+ }
+}
+
+/*
+ * DMA clean up for command errors
+ */
+static void mmc_dma_cleanup(struct mmc_omap_host *host)
+{
+ host->data->error = -ETIMEDOUT;
+
+ if (host->use_dma && host->dma_ch != -1) {
+ dma_unmap_sg(mmc_dev(host->mmc), host->data->sg, host->dma_len,
+ host->dma_dir);
+ omap_free_dma(host->dma_ch);
+ host->dma_ch = -1;
+ up(&host->sem);
+ }
+ host->data = NULL;
+ host->datadir = OMAP_MMC_DATADIR_NONE;
+}
+
+/*
+ * Readable error output
+ */
+#ifdef CONFIG_MMC_DEBUG
+static void mmc_omap_report_irq(struct mmc_omap_host *host, u32 status)
+{
+ /* --- means reserved bit without definition at documentation */
+ static const char *mmc_omap_status_bits[] = {
+ "CC", "TC", "BGE", "---", "BWR", "BRR", "---", "---", "CIRQ",
+ "OBI", "---", "---", "---", "---", "---", "ERRI", "CTO", "CCRC",
+ "CEB", "CIE", "DTO", "DCRC", "DEB", "---", "ACE", "---",
+ "---", "---", "---", "CERR", "CERR", "BADA", "---", "---", "---"
+ };
+ char res[256];
+ char *buf = res;
+ int len, i;
+
+ len = sprintf(buf, "MMC IRQ 0x%x :", status);
+ buf += len;
+
+ for (i = 0; i < ARRAY_SIZE(mmc_omap_status_bits); i++)
+ if (status & (1 << i)) {
+ len = sprintf(buf, " %s", mmc_omap_status_bits[i]);
+ buf += len;
+ }
+
+ dev_dbg(mmc_dev(host->mmc), "%s\n", res);
+}
+#endif /* CONFIG_MMC_DEBUG */
+
+
+/*
+ * MMC controller IRQ handler
+ */
+static irqreturn_t mmc_omap_irq(int irq, void *dev_id)
+{
+ struct mmc_omap_host *host = dev_id;
+ struct mmc_data *data;
+ int end_cmd = 0, end_trans = 0, status;
+
+ if (host->cmd == NULL && host->data == NULL) {
+ OMAP_HSMMC_WRITE(host->base, STAT,
+ OMAP_HSMMC_READ(host->base, STAT));
+ return IRQ_HANDLED;
+ }
+
+ data = host->data;
+ status = OMAP_HSMMC_READ(host->base, STAT);
+ dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
+
+ if (status & ERR) {
+#ifdef CONFIG_MMC_DEBUG
+ mmc_omap_report_irq(host, status);
+#endif
+ if ((status & CMD_TIMEOUT) ||
+ (status & CMD_CRC)) {
+ if (host->cmd) {
+ if (status & CMD_TIMEOUT) {
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base,
+ SYSCTL) | SRC);
+ while (OMAP_HSMMC_READ(host->base,
+ SYSCTL) & SRC)
+ ;
+
+ host->cmd->error = -ETIMEDOUT;
+ } else {
+ host->cmd->error = -EILSEQ;
+ }
+ end_cmd = 1;
+ }
+ if (host->data)
+ mmc_dma_cleanup(host);
+ }
+ if ((status & DATA_TIMEOUT) ||
+ (status & DATA_CRC)) {
+ if (host->data) {
+ if (status & DATA_TIMEOUT)
+ mmc_dma_cleanup(host);
+ else
+ host->data->error = -EILSEQ;
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base,
+ SYSCTL) | SRD);
+ while (OMAP_HSMMC_READ(host->base,
+ SYSCTL) & SRD)
+ ;
+ end_trans = 1;
+ }
+ }
+ if (status & CARD_ERR) {
+ dev_dbg(mmc_dev(host->mmc),
+ "Ignoring card err CMD%d\n", host->cmd->opcode);
+ if (host->cmd)
+ end_cmd = 1;
+ if (host->data)
+ end_trans = 1;
+ }
+ }
+
+ OMAP_HSMMC_WRITE(host->base, STAT, status);
+
+ if (end_cmd || (status & CC))
+ mmc_omap_cmd_done(host, host->cmd);
+ if (end_trans || (status & TC))
+ mmc_omap_xfer_done(host, data);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * Switch MMC operating voltage
+ */
+static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
+{
+ u32 reg_val = 0;
+ int ret;
+
+ /* Disable the clocks */
+ clk_disable(host->fclk);
+ clk_disable(host->iclk);
+ clk_disable(host->dbclk);
+
+ /* Turn the power off */
+ ret = mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+ if (ret != 0)
+ goto err;
+
+ /* Turn the power ON with given VDD 1.8 or 3.0v */
+ ret = mmc_slot(host).set_power(host->dev, host->slot_id, 1, vdd);
+ if (ret != 0)
+ goto err;
+
+ clk_enable(host->fclk);
+ clk_enable(host->iclk);
+ clk_enable(host->dbclk);
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
+ reg_val = OMAP_HSMMC_READ(host->base, HCTL);
+ /*
+ * If a MMC dual voltage card is detected, the set_ios fn calls
+ * this fn with VDD bit set for 1.8V. Upon card removal from the
+ * slot, omap_mmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
+ *
+ * Only MMC1 supports 3.0V. MMC2 will not function if SDVS30 is
+ * set in HCTL.
+ */
+ if (host->id == OMAP_MMC1_DEVID && (((1 << vdd) == MMC_VDD_32_33) ||
+ ((1 << vdd) == MMC_VDD_33_34)))
+ reg_val |= SDVS30;
+ if ((1 << vdd) == MMC_VDD_165_195)
+ reg_val |= SDVS18;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+
+ return 0;
+err:
+ dev_dbg(mmc_dev(host->mmc), "Unable to switch operating voltage\n");
+ return ret;
+}
+
+/*
+ * Work Item to notify the core about card insertion/removal
+ */
+static void mmc_omap_detect(struct work_struct *work)
+{
+ struct mmc_omap_host *host = container_of(work, struct mmc_omap_host,
+ mmc_carddetect_work);
+
+ sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
+ if (host->carddetect) {
+ mmc_detect_change(host->mmc, (HZ * 200) / 1000);
+ } else {
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | SRD);
+ while (OMAP_HSMMC_READ(host->base, SYSCTL) & SRD)
+ ;
+
+ mmc_detect_change(host->mmc, (HZ * 50) / 1000);
+ }
+}
+
+/*
+ * ISR for handling card insertion and removal
+ */
+static irqreturn_t omap_mmc_cd_handler(int irq, void *dev_id)
+{
+ struct mmc_omap_host *host = (struct mmc_omap_host *)dev_id;
+
+ host->carddetect = mmc_slot(host).card_detect(irq);
+ schedule_work(&host->mmc_carddetect_work);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * DMA call back function
+ */
+static void mmc_omap_dma_cb(int lch, u16 ch_status, void *data)
+{
+ struct mmc_omap_host *host = data;
+
+ if (ch_status & OMAP2_DMA_MISALIGNED_ERR_IRQ)
+ dev_dbg(mmc_dev(host->mmc), "MISALIGNED_ADRS_ERR\n");
+
+ if (host->dma_ch < 0)
+ return;
+
+ omap_free_dma(host->dma_ch);
+ host->dma_ch = -1;
+ /*
+ * DMA Callback: run in interrupt context.
+ * mutex_unlock will through a kernel warning if used.
+ */
+ up(&host->sem);
+}
+
+/*
+ * Configure dma src and destination parameters
+ */
+static int mmc_omap_config_dma_param(int sync_dir, struct mmc_omap_host *host,
+ struct mmc_data *data)
+{
+ if (sync_dir == 0) {
+ omap_set_dma_dest_params(host->dma_ch, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ (host->mapbase + OMAP_HSMMC_DATA), 0, 0);
+ omap_set_dma_src_params(host->dma_ch, 0,
+ OMAP_DMA_AMODE_POST_INC,
+ sg_dma_address(&data->sg[0]), 0, 0);
+ } else {
+ omap_set_dma_src_params(host->dma_ch, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ (host->mapbase + OMAP_HSMMC_DATA), 0, 0);
+ omap_set_dma_dest_params(host->dma_ch, 0,
+ OMAP_DMA_AMODE_POST_INC,
+ sg_dma_address(&data->sg[0]), 0, 0);
+ }
+ return 0;
+}
+/*
+ * Routine to configure and start DMA for the MMC card
+ */
+static int
+mmc_omap_start_dma_transfer(struct mmc_omap_host *host, struct mmc_request *req)
+{
+ int sync_dev, sync_dir = 0;
+ int dma_ch = 0, ret = 0, err = 1;
+ struct mmc_data *data = req->data;
+
+ /*
+ * If for some reason the DMA transfer is still active,
+ * we wait for timeout period and free the dma
+ */
+ if (host->dma_ch != -1) {
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(100);
+ if (down_trylock(&host->sem)) {
+ omap_free_dma(host->dma_ch);
+ host->dma_ch = -1;
+ up(&host->sem);
+ return err;
+ }
+ } else {
+ if (down_trylock(&host->sem))
+ return err;
+ }
+
+ if (!(data->flags & MMC_DATA_WRITE)) {
+ host->dma_dir = DMA_FROM_DEVICE;
+ if (host->id == OMAP_MMC1_DEVID)
+ sync_dev = OMAP24XX_DMA_MMC1_RX;
+ else
+ sync_dev = OMAP24XX_DMA_MMC2_RX;
+ } else {
+ host->dma_dir = DMA_TO_DEVICE;
+ if (host->id == OMAP_MMC1_DEVID)
+ sync_dev = OMAP24XX_DMA_MMC1_TX;
+ else
+ sync_dev = OMAP24XX_DMA_MMC2_TX;
+ }
+
+ ret = omap_request_dma(sync_dev, "MMC/SD", mmc_omap_dma_cb,
+ host, &dma_ch);
+ if (ret != 0) {
+ dev_dbg(mmc_dev(host->mmc),
+ "%s: omap_request_dma() failed with %d\n",
+ mmc_hostname(host->mmc), ret);
+ return ret;
+ }
+
+ host->dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg,
+ data->sg_len, host->dma_dir);
+ host->dma_ch = dma_ch;
+
+ if (!(data->flags & MMC_DATA_WRITE))
+ mmc_omap_config_dma_param(1, host, data);
+ else
+ mmc_omap_config_dma_param(0, host, data);
+
+ if ((data->blksz % 4) == 0)
+ omap_set_dma_transfer_params(dma_ch, OMAP_DMA_DATA_TYPE_S32,
+ (data->blksz / 4), data->blocks, OMAP_DMA_SYNC_FRAME,
+ sync_dev, sync_dir);
+ else
+ /* REVISIT: The MMC buffer increments only when MSB is written.
+ * Return error for blksz which is non multiple of four.
+ */
+ return -EINVAL;
+
+ omap_start_dma(dma_ch);
+ return 0;
+}
+
+static void set_data_timeout(struct mmc_omap_host *host,
+ struct mmc_request *req)
+{
+ unsigned int timeout, cycle_ns;
+ uint32_t reg, clkd, dto = 0;
+
+ reg = OMAP_HSMMC_READ(host->base, SYSCTL);
+ clkd = (reg & CLKD_MASK) >> CLKD_SHIFT;
+ if (clkd == 0)
+ clkd = 1;
+
+ cycle_ns = 1000000000 / (clk_get_rate(host->fclk) / clkd);
+ timeout = req->data->timeout_ns / cycle_ns;
+ timeout += req->data->timeout_clks;
+ if (timeout) {
+ while ((timeout & 0x80000000) == 0) {
+ dto += 1;
+ timeout <<= 1;
+ }
+ dto = 31 - dto;
+ timeout <<= 1;
+ if (timeout && dto)
+ dto += 1;
+ if (dto >= 13)
+ dto -= 13;
+ else
+ dto = 0;
+ if (dto > 14)
+ dto = 14;
+ }
+
+ reg &= ~DTO_MASK;
+ reg |= dto << DTO_SHIFT;
+ OMAP_HSMMC_WRITE(host->base, SYSCTL, reg);
+}
+
+/*
+ * Configure block length for MMC/SD cards and initiate the transfer.
+ */
+static int
+mmc_omap_prepare_data(struct mmc_omap_host *host, struct mmc_request *req)
+{
+ int ret;
+ host->data = req->data;
+
+ if (req->data == NULL) {
+ host->datadir = OMAP_MMC_DATADIR_NONE;
+ OMAP_HSMMC_WRITE(host->base, BLK, 0);
+ return 0;
+ }
+
+ OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz)
+ | (req->data->blocks << 16));
+ set_data_timeout(host, req);
+
+ host->datadir = (req->data->flags & MMC_DATA_WRITE) ?
+ OMAP_MMC_DATADIR_WRITE : OMAP_MMC_DATADIR_READ;
+
+ if (host->use_dma) {
+ ret = mmc_omap_start_dma_transfer(host, req);
+ if (ret != 0) {
+ dev_dbg(mmc_dev(host->mmc), "MMC start dma failure\n");
+ return ret;
+ }
+ }
+ return 0;
+}
+
+/*
+ * Request function. for read/write operation
+ */
+static void omap_mmc_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+ struct mmc_omap_host *host = mmc_priv(mmc);
+
+ WARN_ON(host->mrq != NULL);
+ host->mrq = req;
+ mmc_omap_prepare_data(host, req);
+ mmc_omap_start_command(host, req->cmd, req->data);
+}
+
+
+/* Routine to configure clock values. Exposed API to core */
+static void omap_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct mmc_omap_host *host = mmc_priv(mmc);
+ u16 dsor = 0;
+ unsigned long regval;
+ unsigned long timeout;
+
+ switch (ios->power_mode) {
+ case MMC_POWER_OFF:
+ mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+ /*
+ * Reset bus voltage to 3V if it got set to 1.8V earlier.
+ * REVISIT: If we are able to detect cards after unplugging
+ * a 1.8V card, this code should not be needed.
+ */
+ if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
+ int vdd = fls(host->mmc->ocr_avail) - 1;
+ if (omap_mmc_switch_opcond(host, vdd) != 0)
+ host->mmc->ios.vdd = vdd;
+ }
+ break;
+ case MMC_POWER_UP:
+ mmc_slot(host).set_power(host->dev, host->slot_id, 1, ios->vdd);
+ break;
+ }
+
+ switch (mmc->ios.bus_width) {
+ case MMC_BUS_WIDTH_4:
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
+ break;
+ case MMC_BUS_WIDTH_1:
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
+ break;
+ }
+
+ if (host->id == OMAP_MMC1_DEVID) {
+ /* Only MMC1 can operate at 3V/1.8V */
+ if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
+ (ios->vdd == DUAL_VOLT_OCR_BIT)) {
+ /*
+ * The mmc_select_voltage fn of the core does
+ * not seem to set the power_mode to
+ * MMC_POWER_UP upon recalculating the voltage.
+ * vdd 1.8v.
+ */
+ if (omap_mmc_switch_opcond(host, ios->vdd) != 0)
+ dev_dbg(mmc_dev(host->mmc),
+ "Switch operation failed\n");
+ }
+ }
+
+ if (ios->clock) {
+ dsor = OMAP_MMC_MASTER_CLOCK / ios->clock;
+ if (dsor < 1)
+ dsor = 1;
+
+ if (OMAP_MMC_MASTER_CLOCK / dsor > ios->clock)
+ dsor++;
+
+ if (dsor > 250)
+ dsor = 250;
+ }
+ omap_mmc_stop_clock(host);
+ regval = OMAP_HSMMC_READ(host->base, SYSCTL);
+ regval = regval & ~(CLKD_MASK);
+ regval = regval | (dsor << 6) | (DTO << 16);
+ OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
+
+ /* Wait till the ICS bit is set */
+ timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+ while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != 0x2
+ && time_before(jiffies, timeout))
+ msleep(1);
+
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | CEN);
+
+ if (ios->power_mode == MMC_POWER_ON)
+ send_init_stream(host);
+
+ if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
+ OMAP_HSMMC_WRITE(host->base, CON,
+ OMAP_HSMMC_READ(host->base, CON) | OD);
+}
+
+static int omap_hsmmc_get_cd(struct mmc_host *mmc)
+{
+ struct mmc_omap_host *host = mmc_priv(mmc);
+ struct omap_mmc_platform_data *pdata = host->pdata;
+
+ if (!pdata->slots[0].card_detect)
+ return -ENOSYS;
+ return pdata->slots[0].card_detect(pdata->slots[0].card_detect_irq);
+}
+
+static int omap_hsmmc_get_ro(struct mmc_host *mmc)
+{
+ struct mmc_omap_host *host = mmc_priv(mmc);
+ struct omap_mmc_platform_data *pdata = host->pdata;
+
+ if (!pdata->slots[0].get_ro)
+ return -ENOSYS;
+ return pdata->slots[0].get_ro(host->dev, 0);
+}
+
+static struct mmc_host_ops mmc_omap_ops = {
+ .request = omap_mmc_request,
+ .set_ios = omap_mmc_set_ios,
+ .get_cd = omap_hsmmc_get_cd,
+ .get_ro = omap_hsmmc_get_ro,
+ /* NYET -- enable_sdio_irq */
+};
+
+static int __init omap_mmc_probe(struct platform_device *pdev)
+{
+ struct omap_mmc_platform_data *pdata = pdev->dev.platform_data;
+ struct mmc_host *mmc;
+ struct mmc_omap_host *host = NULL;
+ struct resource *res;
+ int ret = 0, irq;
+ u32 hctl, capa;
+
+ if (pdata == NULL) {
+ dev_err(&pdev->dev, "Platform Data is missing\n");
+ return -ENXIO;
+ }
+
+ if (pdata->nr_slots == 0) {
+ dev_err(&pdev->dev, "No Slots\n");
+ return -ENXIO;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (res == NULL || irq < 0)
+ return -ENXIO;
+
+ res = request_mem_region(res->start, res->end - res->start + 1,
+ pdev->name);
+ if (res == NULL)
+ return -EBUSY;
+
+ mmc = mmc_alloc_host(sizeof(struct mmc_omap_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->pdata = pdata;
+ host->dev = &pdev->dev;
+ host->use_dma = 1;
+ host->dev->dma_mask = &pdata->dma_mask;
+ host->dma_ch = -1;
+ host->irq = irq;
+ host->id = pdev->id;
+ host->slot_id = 0;
+ host->mapbase = res->start;
+ host->base = ioremap(host->mapbase, SZ_4K);
+
+ platform_set_drvdata(pdev, host);
+ INIT_WORK(&host->mmc_carddetect_work, mmc_omap_detect);
+
+ mmc->ops = &mmc_omap_ops;
+ mmc->f_min = 400000;
+ mmc->f_max = 52000000;
+
+ sema_init(&host->sem, 1);
+
+ host->iclk = clk_get(&pdev->dev, "mmchs_ick");
+ if (IS_ERR(host->iclk)) {
+ ret = PTR_ERR(host->iclk);
+ host->iclk = NULL;
+ goto err1;
+ }
+ host->fclk = clk_get(&pdev->dev, "mmchs_fck");
+ if (IS_ERR(host->fclk)) {
+ ret = PTR_ERR(host->fclk);
+ host->fclk = NULL;
+ clk_put(host->iclk);
+ goto err1;
+ }
+
+ if (clk_enable(host->fclk) != 0) {
+ clk_put(host->iclk);
+ clk_put(host->fclk);
+ goto err1;
+ }
+
+ if (clk_enable(host->iclk) != 0) {
+ clk_disable(host->fclk);
+ clk_put(host->iclk);
+ clk_put(host->fclk);
+ goto err1;
+ }
+
+ host->dbclk = clk_get(&pdev->dev, "mmchsdb_fck");
+ /*
+ * MMC can still work without debounce clock.
+ */
+ if (IS_ERR(host->dbclk))
+ dev_warn(mmc_dev(host->mmc), "Failed to get debounce clock\n");
+ else
+ if (clk_enable(host->dbclk) != 0)
+ dev_dbg(mmc_dev(host->mmc), "Enabling debounce"
+ " clk failed\n");
+ else
+ host->dbclk_enabled = 1;
+
+#ifdef CONFIG_MMC_BLOCK_BOUNCE
+ mmc->max_phys_segs = 1;
+ mmc->max_hw_segs = 1;
+#endif
+ mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
+ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_req_size;
+
+ mmc->ocr_avail = mmc_slot(host).ocr_mask;
+ mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED;
+
+ if (pdata->slots[host->slot_id].wires >= 4)
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+ /* Only MMC1 supports 3.0V */
+ if (host->id == OMAP_MMC1_DEVID) {
+ hctl = SDVS30;
+ capa = VS30 | VS18;
+ } else {
+ hctl = SDVS18;
+ capa = VS18;
+ }
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | hctl);
+
+ OMAP_HSMMC_WRITE(host->base, CAPA,
+ OMAP_HSMMC_READ(host->base, CAPA) | capa);
+
+ /* Set the controller to AUTO IDLE mode */
+ OMAP_HSMMC_WRITE(host->base, SYSCONFIG,
+ OMAP_HSMMC_READ(host->base, SYSCONFIG) | AUTOIDLE);
+
+ /* Set SD bus power bit */
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+
+ /* Request IRQ for MMC operations */
+ ret = request_irq(host->irq, mmc_omap_irq, IRQF_DISABLED,
+ mmc_hostname(mmc), host);
+ if (ret) {
+ dev_dbg(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n");
+ goto err_irq;
+ }
+
+ if (pdata->init != NULL) {
+ if (pdata->init(&pdev->dev) != 0) {
+ dev_dbg(mmc_dev(host->mmc),
+ "Unable to configure MMC IRQs\n");
+ goto err_irq_cd_init;
+ }
+ }
+
+ /* Request IRQ for card detect */
+ if ((mmc_slot(host).card_detect_irq) && (mmc_slot(host).card_detect)) {
+ ret = request_irq(mmc_slot(host).card_detect_irq,
+ omap_mmc_cd_handler,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING
+ | IRQF_DISABLED,
+ mmc_hostname(mmc), host);
+ if (ret) {
+ dev_dbg(mmc_dev(host->mmc),
+ "Unable to grab MMC CD IRQ\n");
+ goto err_irq_cd;
+ }
+ }
+
+ OMAP_HSMMC_WRITE(host->base, ISE, INT_EN_MASK);
+ OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
+
+ mmc_add_host(mmc);
+
+ if (host->pdata->slots[host->slot_id].name != NULL) {
+ ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
+ if (ret < 0)
+ goto err_slot_name;
+ }
+ if (mmc_slot(host).card_detect_irq && mmc_slot(host).card_detect &&
+ host->pdata->slots[host->slot_id].get_cover_state) {
+ ret = device_create_file(&mmc->class_dev,
+ &dev_attr_cover_switch);
+ if (ret < 0)
+ goto err_cover_switch;
+ }
+
+ return 0;
+
+err_cover_switch:
+ device_remove_file(&mmc->class_dev, &dev_attr_cover_switch);
+err_slot_name:
+ mmc_remove_host(mmc);
+err_irq_cd:
+ free_irq(mmc_slot(host).card_detect_irq, host);
+err_irq_cd_init:
+ free_irq(host->irq, host);
+err_irq:
+ clk_disable(host->fclk);
+ clk_disable(host->iclk);
+ clk_put(host->fclk);
+ clk_put(host->iclk);
+ if (host->dbclk_enabled) {
+ clk_disable(host->dbclk);
+ clk_put(host->dbclk);
+ }
+
+err1:
+ iounmap(host->base);
+err:
+ dev_dbg(mmc_dev(host->mmc), "Probe Failed\n");
+ release_mem_region(res->start, res->end - res->start + 1);
+ if (host)
+ mmc_free_host(mmc);
+ return ret;
+}
+
+static int omap_mmc_remove(struct platform_device *pdev)
+{
+ struct mmc_omap_host *host = platform_get_drvdata(pdev);
+ struct resource *res;
+
+ if (host) {
+ mmc_remove_host(host->mmc);
+ if (host->pdata->cleanup)
+ host->pdata->cleanup(&pdev->dev);
+ free_irq(host->irq, host);
+ if (mmc_slot(host).card_detect_irq)
+ free_irq(mmc_slot(host).card_detect_irq, host);
+ flush_scheduled_work();
+
+ clk_disable(host->fclk);
+ clk_disable(host->iclk);
+ clk_put(host->fclk);
+ clk_put(host->iclk);
+ if (host->dbclk_enabled) {
+ clk_disable(host->dbclk);
+ clk_put(host->dbclk);
+ }
+
+ mmc_free_host(host->mmc);
+ iounmap(host->base);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res)
+ release_mem_region(res->start, res->end - res->start + 1);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int omap_mmc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ int ret = 0;
+ struct mmc_omap_host *host = platform_get_drvdata(pdev);
+
+ if (host && host->suspended)
+ return 0;
+
+ if (host) {
+ ret = mmc_suspend_host(host->mmc, state);
+ if (ret == 0) {
+ host->suspended = 1;
+
+ OMAP_HSMMC_WRITE(host->base, ISE, 0);
+ OMAP_HSMMC_WRITE(host->base, IE, 0);
+
+ if (host->pdata->suspend) {
+ ret = host->pdata->suspend(&pdev->dev,
+ host->slot_id);
+ if (ret)
+ dev_dbg(mmc_dev(host->mmc),
+ "Unable to handle MMC board"
+ " level suspend\n");
+ }
+
+ if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL)
+ & SDVSCLR);
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL)
+ | SDVS30);
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL)
+ | SDBP);
+ }
+
+ clk_disable(host->fclk);
+ clk_disable(host->iclk);
+ clk_disable(host->dbclk);
+ }
+
+ }
+ return ret;
+}
+
+/* Routine to resume the MMC device */
+static int omap_mmc_resume(struct platform_device *pdev)
+{
+ int ret = 0;
+ struct mmc_omap_host *host = platform_get_drvdata(pdev);
+
+ if (host && !host->suspended)
+ return 0;
+
+ if (host) {
+
+ ret = clk_enable(host->fclk);
+ if (ret)
+ goto clk_en_err;
+
+ ret = clk_enable(host->iclk);
+ if (ret) {
+ clk_disable(host->fclk);
+ clk_put(host->fclk);
+ goto clk_en_err;
+ }
+
+ if (clk_enable(host->dbclk) != 0)
+ dev_dbg(mmc_dev(host->mmc),
+ "Enabling debounce clk failed\n");
+
+ if (host->pdata->resume) {
+ ret = host->pdata->resume(&pdev->dev, host->slot_id);
+ if (ret)
+ dev_dbg(mmc_dev(host->mmc),
+ "Unmask interrupt failed\n");
+ }
+
+ /* Notify the core to resume the host */
+ ret = mmc_resume_host(host->mmc);
+ if (ret == 0)
+ host->suspended = 0;
+ }
+
+ return ret;
+
+clk_en_err:
+ dev_dbg(mmc_dev(host->mmc),
+ "Failed to enable MMC clocks during resume\n");
+ return ret;
+}
+
+#else
+#define omap_mmc_suspend NULL
+#define omap_mmc_resume NULL
+#endif
+
+static struct platform_driver omap_mmc_driver = {
+ .probe = omap_mmc_probe,
+ .remove = omap_mmc_remove,
+ .suspend = omap_mmc_suspend,
+ .resume = omap_mmc_resume,
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init omap_mmc_init(void)
+{
+ /* Register the MMC driver */
+ return platform_driver_register(&omap_mmc_driver);
+}
+
+static void __exit omap_mmc_cleanup(void)
+{
+ /* Unregister MMC driver */
+ platform_driver_unregister(&omap_mmc_driver);
+}
+
+module_init(omap_mmc_init);
+module_exit(omap_mmc_cleanup);
+
+MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Texas Instruments Inc");
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 3c5483b75da4..9702ad3774cf 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -180,7 +180,15 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
else
DALGN &= ~(1 << host->dma);
DDADR(host->dma) = host->sg_dma;
- DCSR(host->dma) = DCSR_RUN;
+
+ /*
+ * workaround for erratum #91:
+ * only start DMA now if we are doing a read,
+ * otherwise we wait until CMD/RESP has finished
+ * before starting DMA.
+ */
+ if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
+ DCSR(host->dma) = DCSR_RUN;
}
static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
@@ -251,23 +259,28 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat)
if (stat & STAT_TIME_OUT_RESPONSE) {
cmd->error = -ETIMEDOUT;
} else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
-#ifdef CONFIG_PXA27x
/*
* workaround for erratum #42:
* Intel PXA27x Family Processor Specification Update Rev 001
* A bogus CRC error can appear if the msb of a 136 bit
* response is a one.
*/
- if (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000) {
+ if (cpu_is_pxa27x() &&
+ (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000))
pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode);
- } else
-#endif
- cmd->error = -EILSEQ;
+ else
+ cmd->error = -EILSEQ;
}
pxamci_disable_irq(host, END_CMD_RES);
if (host->data && !cmd->error) {
pxamci_enable_irq(host, DATA_TRAN_DONE);
+ /*
+ * workaround for erratum #91, if doing write
+ * enable DMA late
+ */
+ if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
+ DCSR(host->dma) = DCSR_RUN;
} else {
pxamci_finish_request(host, host->mrq);
}
diff --git a/drivers/mmc/host/ricoh_mmc.c b/drivers/mmc/host/ricoh_mmc.c
index be9e7b32b34e..f62790513322 100644
--- a/drivers/mmc/host/ricoh_mmc.c
+++ b/drivers/mmc/host/ricoh_mmc.c
@@ -196,7 +196,7 @@ static void __devexit ricoh_mmc_remove(struct pci_dev *pdev)
pci_set_drvdata(pdev, NULL);
}
-static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state)
+static int ricoh_mmc_suspend_late(struct pci_dev *pdev, pm_message_t state)
{
struct pci_dev *fw_dev = NULL;
@@ -210,7 +210,7 @@ static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state)
return 0;
}
-static int ricoh_mmc_resume(struct pci_dev *pdev)
+static int ricoh_mmc_resume_early(struct pci_dev *pdev)
{
struct pci_dev *fw_dev = NULL;
@@ -229,8 +229,8 @@ static struct pci_driver ricoh_mmc_driver = {
.id_table = pci_ids,
.probe = ricoh_mmc_probe,
.remove = __devexit_p(ricoh_mmc_remove),
- .suspend = ricoh_mmc_suspend,
- .resume = ricoh_mmc_resume,
+ .suspend_late = ricoh_mmc_suspend_late,
+ .resume_early = ricoh_mmc_resume_early,
};
/*****************************************************************************\
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index fcc98a4cce3c..35a98eec7414 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -20,7 +20,7 @@
#include <linux/irq.h>
#include <linux/io.h>
-#include <asm/dma.h>
+#include <mach/dma.h>
#include <mach/regs-sdi.h>
#include <mach/regs-gpio.h>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-10 10:29:10 +0000