diff options
Diffstat (limited to 'arch/arm/mach-omap2')
-rw-r--r-- | arch/arm/mach-omap2/Kconfig | 1 | ||||
-rw-r--r-- | arch/arm/mach-omap2/board-omap3beagle.c | 22 | ||||
-rw-r--r-- | arch/arm/mach-omap2/control.h | 1 | ||||
-rw-r--r-- | arch/arm/mach-omap2/mux34xx.c | 8 | ||||
-rw-r--r-- | arch/arm/mach-omap2/omap_opp_data.h | 9 | ||||
-rw-r--r-- | arch/arm/mach-omap2/omap_twl.c | 73 | ||||
-rw-r--r-- | arch/arm/mach-omap2/opp4xxx_data.c | 98 | ||||
-rw-r--r-- | arch/arm/mach-omap2/pm.c | 30 | ||||
-rw-r--r-- | arch/arm/mach-omap2/pm.h | 11 | ||||
-rw-r--r-- | arch/arm/mach-omap2/pm34xx.c | 30 | ||||
-rw-r--r-- | arch/arm/mach-omap2/serial.c | 5 | ||||
-rw-r--r-- | arch/arm/mach-omap2/sr_device.c | 13 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vc.c | 451 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vc.h | 8 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vc3xxx_data.c | 22 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vc44xx_data.c | 28 | ||||
-rw-r--r-- | arch/arm/mach-omap2/voltage.h | 44 | ||||
-rw-r--r-- | arch/arm/mach-omap2/voltagedomains3xxx_data.c | 5 | ||||
-rw-r--r-- | arch/arm/mach-omap2/voltagedomains44xx_data.c | 25 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vp.c | 19 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vp.h | 7 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vp3xxx_data.c | 10 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vp44xx_data.c | 15 |
23 files changed, 796 insertions, 139 deletions
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 98268fa66a3b..c81bc508e7a3 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -11,7 +11,6 @@ config ARCH_OMAP2PLUS_TYPICAL select I2C_OMAP select MENELAUS if ARCH_OMAP2 select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 - select PINCTRL select PM_RUNTIME select REGULATOR select SERIAL_OMAP diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 8471c279ecd8..22c483d5dfa8 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -24,6 +24,7 @@ #include <linux/input.h> #include <linux/gpio_keys.h> #include <linux/opp.h> +#include <linux/cpu.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> @@ -447,27 +448,31 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif -static void __init beagle_opp_init(void) +static int __init beagle_opp_init(void) { int r = 0; - /* Initialize the omap3 opp table */ - if (omap3_opp_init()) { + if (!machine_is_omap3_beagle()) + return 0; + + /* Initialize the omap3 opp table if not already created. */ + r = omap3_opp_init(); + if (IS_ERR_VALUE(r) && (r != -EEXIST)) { pr_err("%s: opp default init failed\n", __func__); - return; + return r; } /* Custom OPP enabled for all xM versions */ if (cpu_is_omap3630()) { struct device *mpu_dev, *iva_dev; - mpu_dev = omap_device_get_by_hwmod_name("mpu"); + mpu_dev = get_cpu_device(0); iva_dev = omap_device_get_by_hwmod_name("iva"); if (IS_ERR(mpu_dev) || IS_ERR(iva_dev)) { pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n", __func__, mpu_dev, iva_dev); - return; + return -ENODEV; } /* Enable MPU 1GHz and lower opps */ r = opp_enable(mpu_dev, 800000000); @@ -487,8 +492,9 @@ static void __init beagle_opp_init(void) opp_disable(iva_dev, 660000000); } } - return; + return 0; } +device_initcall(beagle_opp_init); static void __init omap3_beagle_init(void) { @@ -526,8 +532,6 @@ static void __init omap3_beagle_init(void) /* Ensure SDRC pins are mux'd for self-refresh */ omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT); omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT); - - beagle_opp_init(); } MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board") diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h index 4ca8747b3cc9..3d944d3263d2 100644 --- a/arch/arm/mach-omap2/control.h +++ b/arch/arm/mach-omap2/control.h @@ -201,6 +201,7 @@ #define OMAP44XX_CONTROL_FUSE_MPU_OPPNITRO 0x249 #define OMAP44XX_CONTROL_FUSE_CORE_OPP50 0x254 #define OMAP44XX_CONTROL_FUSE_CORE_OPP100 0x257 +#define OMAP44XX_CONTROL_FUSE_CORE_OPP100OV 0x25A /* AM35XX only CONTROL_GENERAL register offsets */ #define AM35XX_CONTROL_MSUSPENDMUX_6 (OMAP2_CONTROL_GENERAL + 0x0038) diff --git a/arch/arm/mach-omap2/mux34xx.c b/arch/arm/mach-omap2/mux34xx.c index 17f80e4ab162..c47140bbbec4 100644 --- a/arch/arm/mach-omap2/mux34xx.c +++ b/arch/arm/mach-omap2/mux34xx.c @@ -614,16 +614,16 @@ static struct omap_mux __initdata omap3_muxmodes[] = { "sys_off_mode", NULL, NULL, NULL, "gpio_9", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(UART1_CTS, 150, - "uart1_cts", NULL, NULL, NULL, + "uart1_cts", "ssi1_rdy_tx", NULL, NULL, "gpio_150", "hsusb3_tll_clk", NULL, "safe_mode"), _OMAP3_MUXENTRY(UART1_RTS, 149, - "uart1_rts", NULL, NULL, NULL, + "uart1_rts", "ssi1_flag_tx", NULL, NULL, "gpio_149", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(UART1_RX, 151, - "uart1_rx", NULL, "mcbsp1_clkr", "mcspi4_clk", + "uart1_rx", "ss1_wake_tx", "mcbsp1_clkr", "mcspi4_clk", "gpio_151", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(UART1_TX, 148, - "uart1_tx", NULL, NULL, NULL, + "uart1_tx", "ssi1_dat_tx", NULL, NULL, "gpio_148", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(UART2_CTS, 144, "uart2_cts", "mcbsp3_dx", "gpt9_pwm_evt", NULL, diff --git a/arch/arm/mach-omap2/omap_opp_data.h b/arch/arm/mach-omap2/omap_opp_data.h index 7e437bf6024c..336fdfcf88bb 100644 --- a/arch/arm/mach-omap2/omap_opp_data.h +++ b/arch/arm/mach-omap2/omap_opp_data.h @@ -89,8 +89,11 @@ extern struct omap_volt_data omap34xx_vddcore_volt_data[]; extern struct omap_volt_data omap36xx_vddmpu_volt_data[]; extern struct omap_volt_data omap36xx_vddcore_volt_data[]; -extern struct omap_volt_data omap44xx_vdd_mpu_volt_data[]; -extern struct omap_volt_data omap44xx_vdd_iva_volt_data[]; -extern struct omap_volt_data omap44xx_vdd_core_volt_data[]; +extern struct omap_volt_data omap443x_vdd_mpu_volt_data[]; +extern struct omap_volt_data omap443x_vdd_iva_volt_data[]; +extern struct omap_volt_data omap443x_vdd_core_volt_data[]; +extern struct omap_volt_data omap446x_vdd_mpu_volt_data[]; +extern struct omap_volt_data omap446x_vdd_iva_volt_data[]; +extern struct omap_volt_data omap446x_vdd_core_volt_data[]; #endif /* __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H */ diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c index 2bf35dc091be..fefd40166624 100644 --- a/arch/arm/mach-omap2/omap_twl.c +++ b/arch/arm/mach-omap2/omap_twl.c @@ -31,16 +31,6 @@ #define OMAP3_VP_VSTEPMAX_VSTEPMAX 0x04 #define OMAP3_VP_VLIMITTO_TIMEOUT_US 200 -#define OMAP3430_VP1_VLIMITTO_VDDMIN 0x14 -#define OMAP3430_VP1_VLIMITTO_VDDMAX 0x42 -#define OMAP3430_VP2_VLIMITTO_VDDMIN 0x18 -#define OMAP3430_VP2_VLIMITTO_VDDMAX 0x2c - -#define OMAP3630_VP1_VLIMITTO_VDDMIN 0x18 -#define OMAP3630_VP1_VLIMITTO_VDDMAX 0x3c -#define OMAP3630_VP2_VLIMITTO_VDDMIN 0x18 -#define OMAP3630_VP2_VLIMITTO_VDDMAX 0x30 - #define OMAP4_SRI2C_SLAVE_ADDR 0x12 #define OMAP4_VDD_MPU_SR_VOLT_REG 0x55 #define OMAP4_VDD_MPU_SR_CMD_REG 0x56 @@ -54,13 +44,6 @@ #define OMAP4_VP_VSTEPMAX_VSTEPMAX 0x04 #define OMAP4_VP_VLIMITTO_TIMEOUT_US 200 -#define OMAP4_VP_MPU_VLIMITTO_VDDMIN 0xA -#define OMAP4_VP_MPU_VLIMITTO_VDDMAX 0x39 -#define OMAP4_VP_IVA_VLIMITTO_VDDMIN 0xA -#define OMAP4_VP_IVA_VLIMITTO_VDDMAX 0x2D -#define OMAP4_VP_CORE_VLIMITTO_VDDMIN 0xA -#define OMAP4_VP_CORE_VLIMITTO_VDDMAX 0x28 - static bool is_offset_valid; static u8 smps_offset; /* @@ -159,16 +142,11 @@ static u8 twl6030_uv_to_vsel(unsigned long uv) static struct omap_voltdm_pmic omap3_mpu_pmic = { .slew_rate = 4000, .step_size = 12500, - .on_volt = 1200000, - .onlp_volt = 1000000, - .ret_volt = 975000, - .off_volt = 600000, - .volt_setup_time = 0xfff, .vp_erroroffset = OMAP3_VP_CONFIG_ERROROFFSET, .vp_vstepmin = OMAP3_VP_VSTEPMIN_VSTEPMIN, .vp_vstepmax = OMAP3_VP_VSTEPMAX_VSTEPMAX, - .vp_vddmin = OMAP3430_VP1_VLIMITTO_VDDMIN, - .vp_vddmax = OMAP3430_VP1_VLIMITTO_VDDMAX, + .vddmin = 600000, + .vddmax = 1450000, .vp_timeout_us = OMAP3_VP_VLIMITTO_TIMEOUT_US, .i2c_slave_addr = OMAP3_SRI2C_SLAVE_ADDR, .volt_reg_addr = OMAP3_VDD_MPU_SR_CONTROL_REG, @@ -180,16 +158,11 @@ static struct omap_voltdm_pmic omap3_mpu_pmic = { static struct omap_voltdm_pmic omap3_core_pmic = { .slew_rate = 4000, .step_size = 12500, - .on_volt = 1200000, - .onlp_volt = 1000000, - .ret_volt = 975000, - .off_volt = 600000, - .volt_setup_time = 0xfff, .vp_erroroffset = OMAP3_VP_CONFIG_ERROROFFSET, .vp_vstepmin = OMAP3_VP_VSTEPMIN_VSTEPMIN, .vp_vstepmax = OMAP3_VP_VSTEPMAX_VSTEPMAX, - .vp_vddmin = OMAP3430_VP2_VLIMITTO_VDDMIN, - .vp_vddmax = OMAP3430_VP2_VLIMITTO_VDDMAX, + .vddmin = 600000, + .vddmax = 1450000, .vp_timeout_us = OMAP3_VP_VLIMITTO_TIMEOUT_US, .i2c_slave_addr = OMAP3_SRI2C_SLAVE_ADDR, .volt_reg_addr = OMAP3_VDD_CORE_SR_CONTROL_REG, @@ -201,21 +174,17 @@ static struct omap_voltdm_pmic omap3_core_pmic = { static struct omap_voltdm_pmic omap4_mpu_pmic = { .slew_rate = 4000, .step_size = 12660, - .on_volt = 1375000, - .onlp_volt = 1375000, - .ret_volt = 830000, - .off_volt = 0, - .volt_setup_time = 0, .vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET, .vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN, .vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX, - .vp_vddmin = OMAP4_VP_MPU_VLIMITTO_VDDMIN, - .vp_vddmax = OMAP4_VP_MPU_VLIMITTO_VDDMAX, + .vddmin = 0, + .vddmax = 2100000, .vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US, .i2c_slave_addr = OMAP4_SRI2C_SLAVE_ADDR, .volt_reg_addr = OMAP4_VDD_MPU_SR_VOLT_REG, .cmd_reg_addr = OMAP4_VDD_MPU_SR_CMD_REG, .i2c_high_speed = true, + .i2c_pad_load = 3, .vsel_to_uv = twl6030_vsel_to_uv, .uv_to_vsel = twl6030_uv_to_vsel, }; @@ -223,21 +192,17 @@ static struct omap_voltdm_pmic omap4_mpu_pmic = { static struct omap_voltdm_pmic omap4_iva_pmic = { .slew_rate = 4000, .step_size = 12660, - .on_volt = 1188000, - .onlp_volt = 1188000, - .ret_volt = 830000, - .off_volt = 0, - .volt_setup_time = 0, .vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET, .vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN, .vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX, - .vp_vddmin = OMAP4_VP_IVA_VLIMITTO_VDDMIN, - .vp_vddmax = OMAP4_VP_IVA_VLIMITTO_VDDMAX, + .vddmin = 0, + .vddmax = 2100000, .vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US, .i2c_slave_addr = OMAP4_SRI2C_SLAVE_ADDR, .volt_reg_addr = OMAP4_VDD_IVA_SR_VOLT_REG, .cmd_reg_addr = OMAP4_VDD_IVA_SR_CMD_REG, .i2c_high_speed = true, + .i2c_pad_load = 3, .vsel_to_uv = twl6030_vsel_to_uv, .uv_to_vsel = twl6030_uv_to_vsel, }; @@ -245,20 +210,17 @@ static struct omap_voltdm_pmic omap4_iva_pmic = { static struct omap_voltdm_pmic omap4_core_pmic = { .slew_rate = 4000, .step_size = 12660, - .on_volt = 1200000, - .onlp_volt = 1200000, - .ret_volt = 830000, - .off_volt = 0, - .volt_setup_time = 0, .vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET, .vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN, .vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX, - .vp_vddmin = OMAP4_VP_CORE_VLIMITTO_VDDMIN, - .vp_vddmax = OMAP4_VP_CORE_VLIMITTO_VDDMAX, + .vddmin = 0, + .vddmax = 2100000, .vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US, .i2c_slave_addr = OMAP4_SRI2C_SLAVE_ADDR, .volt_reg_addr = OMAP4_VDD_CORE_SR_VOLT_REG, .cmd_reg_addr = OMAP4_VDD_CORE_SR_CMD_REG, + .i2c_high_speed = true, + .i2c_pad_load = 3, .vsel_to_uv = twl6030_vsel_to_uv, .uv_to_vsel = twl6030_uv_to_vsel, }; @@ -289,13 +251,6 @@ int __init omap3_twl_init(void) if (!cpu_is_omap34xx()) return -ENODEV; - if (cpu_is_omap3630()) { - omap3_mpu_pmic.vp_vddmin = OMAP3630_VP1_VLIMITTO_VDDMIN; - omap3_mpu_pmic.vp_vddmax = OMAP3630_VP1_VLIMITTO_VDDMAX; - omap3_core_pmic.vp_vddmin = OMAP3630_VP2_VLIMITTO_VDDMIN; - omap3_core_pmic.vp_vddmax = OMAP3630_VP2_VLIMITTO_VDDMAX; - } - /* * The smartreflex bit on twl4030 specifies if the setting of voltage * is done over the I2C_SR path. Since this setting is independent of diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c index a9fd6d5fe79e..d470b728e720 100644 --- a/arch/arm/mach-omap2/opp4xxx_data.c +++ b/arch/arm/mach-omap2/opp4xxx_data.c @@ -1,7 +1,7 @@ /* * OMAP4 OPP table definitions. * - * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2010-2012 Texas Instruments Incorporated - http://www.ti.com/ * Nishanth Menon * Kevin Hilman * Thara Gopinath @@ -35,7 +35,7 @@ #define OMAP4430_VDD_MPU_OPPTURBO_UV 1313000 #define OMAP4430_VDD_MPU_OPPNITRO_UV 1375000 -struct omap_volt_data omap44xx_vdd_mpu_volt_data[] = { +struct omap_volt_data omap443x_vdd_mpu_volt_data[] = { VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPP50_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP50, 0xf4, 0x0c), VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPP100_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP100, 0xf9, 0x16), VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPPTURBO_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPTURBO, 0xfa, 0x23), @@ -47,7 +47,7 @@ struct omap_volt_data omap44xx_vdd_mpu_volt_data[] = { #define OMAP4430_VDD_IVA_OPP100_UV 1188000 #define OMAP4430_VDD_IVA_OPPTURBO_UV 1300000 -struct omap_volt_data omap44xx_vdd_iva_volt_data[] = { +struct omap_volt_data omap443x_vdd_iva_volt_data[] = { VOLT_DATA_DEFINE(OMAP4430_VDD_IVA_OPP50_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP50, 0xf4, 0x0c), VOLT_DATA_DEFINE(OMAP4430_VDD_IVA_OPP100_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP100, 0xf9, 0x16), VOLT_DATA_DEFINE(OMAP4430_VDD_IVA_OPPTURBO_UV, OMAP44XX_CONTROL_FUSE_IVA_OPPTURBO, 0xfa, 0x23), @@ -57,14 +57,14 @@ struct omap_volt_data omap44xx_vdd_iva_volt_data[] = { #define OMAP4430_VDD_CORE_OPP50_UV 1025000 #define OMAP4430_VDD_CORE_OPP100_UV 1200000 -struct omap_volt_data omap44xx_vdd_core_volt_data[] = { +struct omap_volt_data omap443x_vdd_core_volt_data[] = { VOLT_DATA_DEFINE(OMAP4430_VDD_CORE_OPP50_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP50, 0xf4, 0x0c), VOLT_DATA_DEFINE(OMAP4430_VDD_CORE_OPP100_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP100, 0xf9, 0x16), VOLT_DATA_DEFINE(0, 0, 0, 0), }; -static struct omap_opp_def __initdata omap44xx_opp_def_list[] = { +static struct omap_opp_def __initdata omap443x_opp_def_list[] = { /* MPU OPP1 - OPP50 */ OPP_INITIALIZER("mpu", true, 300000000, OMAP4430_VDD_MPU_OPP50_UV), /* MPU OPP2 - OPP100 */ @@ -86,6 +86,82 @@ static struct omap_opp_def __initdata omap44xx_opp_def_list[] = { /* TODO: add DSP, aess, fdif, gpu */ }; +#define OMAP4460_VDD_MPU_OPP50_UV 1025000 +#define OMAP4460_VDD_MPU_OPP100_UV 1200000 +#define OMAP4460_VDD_MPU_OPPTURBO_UV 1313000 +#define OMAP4460_VDD_MPU_OPPNITRO_UV 1375000 + +struct omap_volt_data omap446x_vdd_mpu_volt_data[] = { + VOLT_DATA_DEFINE(OMAP4460_VDD_MPU_OPP50_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP50, 0xf4, 0x0c), + VOLT_DATA_DEFINE(OMAP4460_VDD_MPU_OPP100_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP100, 0xf9, 0x16), + VOLT_DATA_DEFINE(OMAP4460_VDD_MPU_OPPTURBO_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPTURBO, 0xfa, 0x23), + VOLT_DATA_DEFINE(OMAP4460_VDD_MPU_OPPNITRO_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPNITRO, 0xfa, 0x27), + VOLT_DATA_DEFINE(0, 0, 0, 0), +}; + +#define OMAP4460_VDD_IVA_OPP50_UV 1025000 +#define OMAP4460_VDD_IVA_OPP100_UV 1200000 +#define OMAP4460_VDD_IVA_OPPTURBO_UV 1313000 +#define OMAP4460_VDD_IVA_OPPNITRO_UV 1375000 + +struct omap_volt_data omap446x_vdd_iva_volt_data[] = { + VOLT_DATA_DEFINE(OMAP4460_VDD_IVA_OPP50_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP50, 0xf4, 0x0c), + VOLT_DATA_DEFINE(OMAP4460_VDD_IVA_OPP100_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP100, 0xf9, 0x16), + VOLT_DATA_DEFINE(OMAP4460_VDD_IVA_OPPTURBO_UV, OMAP44XX_CONTROL_FUSE_IVA_OPPTURBO, 0xfa, 0x23), + VOLT_DATA_DEFINE(OMAP4460_VDD_IVA_OPPNITRO_UV, OMAP44XX_CONTROL_FUSE_IVA_OPPNITRO, 0xfa, 0x23), + VOLT_DATA_DEFINE(0, 0, 0, 0), +}; + +#define OMAP4460_VDD_CORE_OPP50_UV 1025000 +#define OMAP4460_VDD_CORE_OPP100_UV 1200000 +#define OMAP4460_VDD_CORE_OPP100_OV_UV 1250000 + +struct omap_volt_data omap446x_vdd_core_volt_data[] = { + VOLT_DATA_DEFINE(OMAP4460_VDD_CORE_OPP50_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP50, 0xf4, 0x0c), + VOLT_DATA_DEFINE(OMAP4460_VDD_CORE_OPP100_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP100, 0xf9, 0x16), + VOLT_DATA_DEFINE(OMAP4460_VDD_CORE_OPP100_OV_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP100OV, 0xf9, 0x16), + VOLT_DATA_DEFINE(0, 0, 0, 0), +}; + +static struct omap_opp_def __initdata omap446x_opp_def_list[] = { + /* MPU OPP1 - OPP50 */ + OPP_INITIALIZER("mpu", true, 350000000, OMAP4460_VDD_MPU_OPP50_UV), + /* MPU OPP2 - OPP100 */ + OPP_INITIALIZER("mpu", true, 700000000, OMAP4460_VDD_MPU_OPP100_UV), + /* MPU OPP3 - OPP-Turbo */ + OPP_INITIALIZER("mpu", true, 920000000, OMAP4460_VDD_MPU_OPPTURBO_UV), + /* + * MPU OPP4 - OPP-Nitro + Disabled as the reference schematics + * recommends TPS623631 - confirm and enable the opp in board file + * XXX: May be we should enable these based on mpu capability and + * Exception board files disable it... + */ + OPP_INITIALIZER("mpu", false, 1200000000, OMAP4460_VDD_MPU_OPPNITRO_UV), + /* MPU OPP4 - OPP-Nitro SpeedBin */ + OPP_INITIALIZER("mpu", false, 1500000000, OMAP4460_VDD_MPU_OPPNITRO_UV), + /* L3 OPP1 - OPP50 */ + OPP_INITIALIZER("l3_main_1", true, 100000000, OMAP4460_VDD_CORE_OPP50_UV), + /* L3 OPP2 - OPP100 */ + OPP_INITIALIZER("l3_main_1", true, 200000000, OMAP4460_VDD_CORE_OPP100_UV), + /* IVA OPP1 - OPP50 */ + OPP_INITIALIZER("iva", true, 133000000, OMAP4460_VDD_IVA_OPP50_UV), + /* IVA OPP2 - OPP100 */ + OPP_INITIALIZER("iva", true, 266100000, OMAP4460_VDD_IVA_OPP100_UV), + /* + * IVA OPP3 - OPP-Turbo + Disabled as the reference schematics + * recommends Phoenix VCORE2 which can supply only 600mA - so the ones + * above this OPP frequency, even though OMAP is capable, should be + * enabled by board file which is sure of the chip power capability + */ + OPP_INITIALIZER("iva", false, 332000000, OMAP4460_VDD_IVA_OPPTURBO_UV), + /* IVA OPP4 - OPP-Nitro */ + OPP_INITIALIZER("iva", false, 430000000, OMAP4460_VDD_IVA_OPPNITRO_UV), + /* IVA OPP5 - OPP-Nitro SpeedBin*/ + OPP_INITIALIZER("iva", false, 500000000, OMAP4460_VDD_IVA_OPPNITRO_UV), + + /* TODO: add DSP, aess, fdif, gpu */ +}; + /** * omap4_opp_init() - initialize omap4 opp table */ @@ -93,12 +169,12 @@ int __init omap4_opp_init(void) { int r = -ENODEV; - if (!cpu_is_omap443x()) - return r; - - r = omap_init_opp_table(omap44xx_opp_def_list, - ARRAY_SIZE(omap44xx_opp_def_list)); - + if (cpu_is_omap443x()) + r = omap_init_opp_table(omap443x_opp_def_list, + ARRAY_SIZE(omap443x_opp_def_list)); + else if (cpu_is_omap446x()) + r = omap_init_opp_table(omap446x_opp_def_list, + ARRAY_SIZE(omap446x_opp_def_list)); return r; } device_initcall(omap4_opp_init); diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 331478f9b864..e5a4c3a0accd 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -40,6 +40,36 @@ static struct omap_device_pm_latency *pm_lats; */ int (*omap_pm_suspend)(void); +/** + * struct omap2_oscillator - Describe the board main oscillator latencies + * @startup_time: oscillator startup latency + * @shutdown_time: oscillator shutdown latency + */ +struct omap2_oscillator { + u32 startup_time; + u32 shutdown_time; +}; + +static struct omap2_oscillator oscillator = { + .startup_time = ULONG_MAX, + .shutdown_time = ULONG_MAX, +}; + +void omap_pm_setup_oscillator(u32 tstart, u32 tshut) +{ + oscillator.startup_time = tstart; + oscillator.shutdown_time = tshut; +} + +void omap_pm_get_oscillator(u32 *tstart, u32 *tshut) +{ + if (!tstart || !tshut) + return; + + *tstart = oscillator.startup_time; + *tshut = oscillator.shutdown_time; +} + static int __init _init_omap_device(char *name) { struct omap_hwmod *oh; diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index 686137d164da..4db7b238a0d5 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -91,6 +91,7 @@ extern void omap3_save_scratchpad_contents(void); #define PM_RTA_ERRATUM_i608 (1 << 0) #define PM_SDRC_WAKEUP_ERRATUM_i583 (1 << 1) +#define PM_PER_MEMORIES_ERRATUM_i582 (1 << 2) #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3) extern u16 pm34xx_errata; @@ -128,4 +129,14 @@ static inline int omap4_twl_init(void) } #endif +#ifdef CONFIG_PM +extern void omap_pm_setup_oscillator(u32 tstart, u32 tshut); +extern void omap_pm_get_oscillator(u32 *tstart, u32 *tshut); +extern void omap_pm_setup_sr_i2c_pcb_length(u32 mm); +#else +static inline void omap_pm_setup_oscillator(u32 tstart, u32 tshut) { } +static inline void omap_pm_get_oscillator(u32 *tstart, u32 *tshut) { } +static inline void omap_pm_setup_sr_i2c_pcb_length(u32 mm) { } +#endif + #endif diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index aa701d76efda..a9b8da1629bf 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -651,14 +651,17 @@ static void __init pm_errata_configure(void) /* Enable the l2 cache toggling in sleep logic */ enable_omap3630_toggle_l2_on_restore(); if (omap_rev() < OMAP3630_REV_ES1_2) - pm34xx_errata |= PM_SDRC_WAKEUP_ERRATUM_i583; + pm34xx_errata |= (PM_SDRC_WAKEUP_ERRATUM_i583 | + PM_PER_MEMORIES_ERRATUM_i582); + } else if (cpu_is_omap34xx()) { + pm34xx_errata |= PM_PER_MEMORIES_ERRATUM_i582; } } int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; - struct clockdomain *neon_clkdm, *mpu_clkdm; + struct clockdomain *neon_clkdm, *mpu_clkdm, *per_clkdm, *wkup_clkdm; int ret; if (!omap3_has_io_chain_ctrl()) @@ -710,6 +713,8 @@ int __init omap3_pm_init(void) neon_clkdm = clkdm_lookup("neon_clkdm"); mpu_clkdm = clkdm_lookup("mpu_clkdm"); + per_clkdm = clkdm_lookup("per_clkdm"); + wkup_clkdm = clkdm_lookup("wkup_clkdm"); #ifdef CONFIG_SUSPEND omap_pm_suspend = omap3_pm_suspend; @@ -726,6 +731,27 @@ int __init omap3_pm_init(void) if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608)) omap3630_ctrl_disable_rta(); + /* + * The UART3/4 FIFO and the sidetone memory in McBSP2/3 are + * not correctly reset when the PER powerdomain comes back + * from OFF or OSWR when the CORE powerdomain is kept active. + * See OMAP36xx Erratum i582 "PER Domain reset issue after + * Domain-OFF/OSWR Wakeup". This wakeup dependency is not a + * complete workaround. The kernel must also prevent the PER + * powerdomain from going to OSWR/OFF while the CORE + * powerdomain is not going to OSWR/OFF. And if PER last + * power state was off while CORE last power state was ON, the + * UART3/4 and McBSP2/3 SIDETONE devices need to run a + * self-test using their loopback tests; if that fails, those + * devices are unusable until the PER/CORE can complete a transition + * from ON to OSWR/OFF and then back to ON. + * + * XXX Technically this workaround is only needed if off-mode + * or OSWR is enabled. + */ + if (IS_PM34XX_ERRATUM(PM_PER_MEMORIES_ERRATUM_i582)) + clkdm_add_wkdep(per_clkdm, wkup_clkdm); + clkdm_add_wkdep(neon_clkdm, mpu_clkdm); if (omap_type() != OMAP2_DEVICE_TYPE_GP) { omap3_secure_ram_storage = diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 812976eac536..aa30a3c20883 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -330,6 +330,11 @@ void __init omap_serial_init_port(struct omap_board_data *bdata, oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt); + if (console_uart_id == bdata->id) { + omap_device_enable(pdev); + pm_runtime_set_active(&pdev->dev); + } + oh->dev_attr = uart; if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads) diff --git a/arch/arm/mach-omap2/sr_device.c b/arch/arm/mach-omap2/sr_device.c index b0e77a407047..b9753fe27232 100644 --- a/arch/arm/mach-omap2/sr_device.c +++ b/arch/arm/mach-omap2/sr_device.c @@ -121,6 +121,19 @@ static int __init sr_dev_init(struct omap_hwmod *oh, void *user) sr_data->senn_mod = 0x1; sr_data->senp_mod = 0x1; + if (cpu_is_omap34xx() || cpu_is_omap44xx()) { + sr_data->err_weight = OMAP3430_SR_ERRWEIGHT; + sr_data->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT; + sr_data->accum_data = OMAP3430_SR_ACCUMDATA; + if (!(strcmp(sr_data->name, "smartreflex_mpu"))) { + sr_data->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT; + sr_data->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT; + } else { + sr_data->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT; + sr_data->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT; + } + } + sr_data->voltdm = voltdm_lookup(sr_dev_attr->sensor_voltdm_name); if (!sr_data->voltdm) { pr_err("%s: Unable to get voltage domain pointer for VDD %s\n", diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c index 880249b17012..687aa86c0d5e 100644 --- a/arch/arm/mach-omap2/vc.c +++ b/arch/arm/mach-omap2/vc.c @@ -11,13 +11,20 @@ #include <linux/delay.h> #include <linux/init.h> #include <linux/bug.h> +#include <linux/io.h> +#include <asm/div64.h> + +#include "iomap.h" #include "soc.h" #include "voltage.h" #include "vc.h" #include "prm-regbits-34xx.h" #include "prm-regbits-44xx.h" #include "prm44xx.h" +#include "pm.h" +#include "scrm44xx.h" +#include "control.h" /** * struct omap_vc_channel_cfg - describe the cfg_channel bitfield @@ -63,6 +70,9 @@ static struct omap_vc_channel_cfg vc_mutant_channel_cfg = { }; static struct omap_vc_channel_cfg *vc_cfg_bits; + +/* Default I2C trace length on pcb, 6.3cm. Used for capacitance calculations. */ +static u32 sr_i2c_pcb_length = 63; #define CFG_CHANNEL_MASK 0x1f /** @@ -135,6 +145,8 @@ int omap_vc_pre_scale(struct voltagedomain *voltdm, vc_cmdval |= (*target_vsel << vc->common->cmd_on_shift); voltdm->write(vc_cmdval, vc->cmdval_reg); + voltdm->vc_param->on = target_volt; + omap_vp_update_errorgain(voltdm, target_volt); return 0; @@ -202,46 +214,389 @@ int omap_vc_bypass_scale(struct voltagedomain *voltdm, return 0; } -static void __init omap3_vfsm_init(struct voltagedomain *voltdm) +/* Convert microsecond value to number of 32kHz clock cycles */ +static inline u32 omap_usec_to_32k(u32 usec) +{ + return DIV_ROUND_UP_ULL(32768ULL * (u64)usec, 1000000ULL); +} + +/* Set oscillator setup time for omap3 */ +static void omap3_set_clksetup(u32 usec, struct voltagedomain *voltdm) +{ + voltdm->write(omap_usec_to_32k(usec), OMAP3_PRM_CLKSETUP_OFFSET); +} + +/** + * omap3_set_i2c_timings - sets i2c sleep timings for a channel + * @voltdm: channel to configure + * @off_mode: select whether retention or off mode values used + * + * Calculates and sets up voltage controller to use I2C based + * voltage scaling for sleep modes. This can be used for either off mode + * or retention. Off mode has additionally an option to use sys_off_mode + * pad, which uses a global signal to program the whole power IC to + * off-mode. + */ +static void omap3_set_i2c_timings(struct voltagedomain *voltdm, bool off_mode) { + unsigned long voltsetup1; + u32 tgt_volt; + + /* + * Oscillator is shut down only if we are using sys_off_mode pad, + * thus we set a minimal setup time here + */ + omap3_set_clksetup(1, voltdm); + + if (off_mode) + tgt_volt = voltdm->vc_param->off; + else + tgt_volt = voltdm->vc_param->ret; + + voltsetup1 = (voltdm->vc_param->on - tgt_volt) / + voltdm->pmic->slew_rate; + + voltsetup1 = voltsetup1 * voltdm->sys_clk.rate / 8 / 1000000 + 1; + + voltdm->rmw(voltdm->vfsm->voltsetup_mask, + voltsetup1 << __ffs(voltdm->vfsm->voltsetup_mask), + voltdm->vfsm->voltsetup_reg); + /* - * Voltage Manager FSM parameters init - * XXX This data should be passed in from the board file + * pmic is not controlling the voltage scaling during retention, + * thus set voltsetup2 to 0 */ - voltdm->write(OMAP3_CLKSETUP, OMAP3_PRM_CLKSETUP_OFFSET); - voltdm->write(OMAP3_VOLTOFFSET, OMAP3_PRM_VOLTOFFSET_OFFSET); - voltdm->write(OMAP3_VOLTSETUP2, OMAP3_PRM_VOLTSETUP2_OFFSET); + voltdm->write(0, OMAP3_PRM_VOLTSETUP2_OFFSET); } -static void __init omap3_vc_init_channel(struct voltagedomain *voltdm) +/** + * omap3_set_off_timings - sets off-mode timings for a channel + * @voltdm: channel to configure + * + * Calculates and sets up off-mode timings for a channel. Off-mode + * can use either I2C based voltage scaling, or alternatively + * sys_off_mode pad can be used to send a global command to power IC. + * This function first checks which mode is being used, and calls + * omap3_set_i2c_timings() if the system is using I2C control mode. + * sys_off_mode has the additional benefit that voltages can be + * scaled to zero volt level with TWL4030 / TWL5030, I2C can only + * scale to 600mV. + */ +static void omap3_set_off_timings(struct voltagedomain *voltdm) { - static bool is_initialized; + unsigned long clksetup; + unsigned long voltsetup2; + unsigned long voltsetup2_old; + u32 val; + u32 tstart, tshut; - if (is_initialized) + /* check if sys_off_mode is used to control off-mode voltages */ + val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET); + if (!(val & OMAP3430_SEL_OFF_MASK)) { + /* No, omap is controlling them over I2C */ + omap3_set_i2c_timings(voltdm, true); return; + } + + omap_pm_get_oscillator(&tstart, &tshut); + omap3_set_clksetup(tstart, voltdm); + + clksetup = voltdm->read(OMAP3_PRM_CLKSETUP_OFFSET); + + /* voltsetup 2 in us */ + voltsetup2 = voltdm->vc_param->on / voltdm->pmic->slew_rate; + + /* convert to 32k clk cycles */ + voltsetup2 = DIV_ROUND_UP(voltsetup2 * 32768, 1000000); + + voltsetup2_old = voltdm->read(OMAP3_PRM_VOLTSETUP2_OFFSET); + + /* + * Update voltsetup2 if higher than current value (needed because + * we have multiple channels with different ramp times), also + * update voltoffset always to value recommended by TRM + */ + if (voltsetup2 > voltsetup2_old) { + voltdm->write(voltsetup2, OMAP3_PRM_VOLTSETUP2_OFFSET); + voltdm->write(clksetup - voltsetup2, + OMAP3_PRM_VOLTOFFSET_OFFSET); + } else + voltdm->write(clksetup - voltsetup2_old, + OMAP3_PRM_VOLTOFFSET_OFFSET); + + /* + * omap is not controlling voltage scaling during off-mode, + * thus set voltsetup1 to 0 + */ + voltdm->rmw(voltdm->vfsm->voltsetup_mask, 0, + voltdm->vfsm->voltsetup_reg); + + /* voltoffset must be clksetup minus voltsetup2 according to TRM */ + voltdm->write(clksetup - voltsetup2, OMAP3_PRM_VOLTOFFSET_OFFSET); +} + +static void __init omap3_vc_init_channel(struct voltagedomain *voltdm) +{ + omap3_set_off_timings(voltdm); +} + +/** + * omap4_calc_volt_ramp - calculates voltage ramping delays on omap4 + * @voltdm: channel to calculate values for + * @voltage_diff: voltage difference in microvolts + * + * Calculates voltage ramp prescaler + counter values for a voltage + * difference on omap4. Returns a field value suitable for writing to + * VOLTSETUP register for a channel in following format: + * bits[8:9] prescaler ... bits[0:5] counter. See OMAP4 TRM for reference. + */ +static u32 omap4_calc_volt_ramp(struct voltagedomain *voltdm, u32 voltage_diff) +{ + u32 prescaler; + u32 cycles; + u32 time; + + time = voltage_diff / voltdm->pmic->slew_rate; + + cycles = voltdm->sys_clk.rate / 1000 * time / 1000; + + cycles /= 64; + prescaler = 0; + + /* shift to next prescaler until no overflow */ + + /* scale for div 256 = 64 * 4 */ + if (cycles > 63) { + cycles /= 4; + prescaler++; + } + + /* scale for div 512 = 256 * 2 */ + if (cycles > 63) { + cycles /= 2; + prescaler++; + } + + /* scale for div 2048 = 512 * 4 */ + if (cycles > 63) { + cycles /= 4; + prescaler++; + } + + /* check for overflow => invalid ramp time */ + if (cycles > 63) { + pr_warn("%s: invalid setuptime for vdd_%s\n", __func__, + voltdm->name); + return 0; + } + + cycles++; - omap3_vfsm_init(voltdm); + return (prescaler << OMAP4430_RAMP_UP_PRESCAL_SHIFT) | + (cycles << OMAP4430_RAMP_UP_COUNT_SHIFT); +} + +/** + * omap4_usec_to_val_scrm - convert microsecond value to SCRM module bitfield + * @usec: microseconds + * @shift: number of bits to shift left + * @mask: bitfield mask + * + * Converts microsecond value to OMAP4 SCRM bitfield. Bitfield is + * shifted to requested position, and checked agains the mask value. + * If larger, forced to the max value of the field (i.e. the mask itself.) + * Returns the SCRM bitfield value. + */ +static u32 omap4_usec_to_val_scrm(u32 usec, int shift, u32 mask) +{ + u32 val; + + val = omap_usec_to_32k(usec) << shift; - is_initialized = true; + /* Check for overflow, if yes, force to max value */ + if (val > mask) + val = mask; + + return val; } +/** + * omap4_set_timings - set voltage ramp timings for a channel + * @voltdm: channel to configure + * @off_mode: whether off-mode values are used + * + * Calculates and sets the voltage ramp up / down values for a channel. + */ +static void omap4_set_timings(struct voltagedomain *voltdm, bool off_mode) +{ + u32 val; + u32 ramp; + int offset; + u32 tstart, tshut; + + if (off_mode) { + ramp = omap4_calc_volt_ramp(voltdm, + voltdm->vc_param->on - voltdm->vc_param->off); + offset = voltdm->vfsm->voltsetup_off_reg; + } else { + ramp = omap4_calc_volt_ramp(voltdm, + voltdm->vc_param->on - voltdm->vc_param->ret); + offset = voltdm->vfsm->voltsetup_reg; + } + + if (!ramp) + return; + + val = voltdm->read(offset); + + val |= ramp << OMAP4430_RAMP_DOWN_COUNT_SHIFT; + + val |= ramp << OMAP4430_RAMP_UP_COUNT_SHIFT; + + voltdm->write(val, offset); + + omap_pm_get_oscillator(&tstart, &tshut); + + val = omap4_usec_to_val_scrm(tstart, OMAP4_SETUPTIME_SHIFT, + OMAP4_SETUPTIME_MASK); + val |= omap4_usec_to_val_scrm(tshut, OMAP4_DOWNTIME_SHIFT, + OMAP4_DOWNTIME_MASK); + + __raw_writel(val, OMAP4_SCRM_CLKSETUPTIME); +} /* OMAP4 specific voltage init functions */ static void __init omap4_vc_init_channel(struct voltagedomain *voltdm) { - static bool is_initialized; - u32 vc_val; + omap4_set_timings(voltdm, true); + omap4_set_timings(voltdm, false); +} + +struct i2c_init_data { + u8 loadbits; + u8 load; + u8 hsscll_38_4; + u8 hsscll_26; + u8 hsscll_19_2; + u8 hsscll_16_8; + u8 hsscll_12; +}; - if (is_initialized) +static const __initdata struct i2c_init_data omap4_i2c_timing_data[] = { + { + .load = 50, + .loadbits = 0x3, + .hsscll_38_4 = 13, + .hsscll_26 = 11, + .hsscll_19_2 = 9, + .hsscll_16_8 = 9, + .hsscll_12 = 8, + }, + { + .load = 25, + .loadbits = 0x2, + .hsscll_38_4 = 13, + .hsscll_26 = 11, + .hsscll_19_2 = 9, + .hsscll_16_8 = 9, + .hsscll_12 = 8, + }, + { + .load = 12, + .loadbits = 0x1, + .hsscll_38_4 = 11, + .hsscll_26 = 10, + .hsscll_19_2 = 9, + .hsscll_16_8 = 9, + .hsscll_12 = 8, + }, + { + .load = 0, + .loadbits = 0x0, + .hsscll_38_4 = 12, + .hsscll_26 = 10, + .hsscll_19_2 = 9, + .hsscll_16_8 = 8, + .hsscll_12 = 8, + }, +}; + +/** + * omap4_vc_i2c_timing_init - sets up board I2C timing parameters + * @voltdm: voltagedomain pointer to get data from + * + * Use PMIC + board supplied settings for calculating the total I2C + * channel capacitance and set the timing parameters based on this. + * Pre-calculated values are provided in data tables, as it is not + * too straightforward to calculate these runtime. + */ +static void __init omap4_vc_i2c_timing_init(struct voltagedomain *voltdm) +{ + u32 capacitance; + u32 val; + u16 hsscll; + const struct i2c_init_data *i2c_data; + + if (!voltdm->pmic->i2c_high_speed) { + pr_warn("%s: only high speed supported!\n", __func__); return; + } + + /* PCB trace capacitance, 0.125pF / mm => mm / 8 */ + capacitance = DIV_ROUND_UP(sr_i2c_pcb_length, 8); + + /* OMAP pad capacitance */ + capacitance += 4; + + /* PMIC pad capacitance */ + capacitance += voltdm->pmic->i2c_pad_load; + + /* Search for capacitance match in the table */ + i2c_data = omap4_i2c_timing_data; + + while (i2c_data->load > capacitance) + i2c_data++; + + /* Select proper values based on sysclk frequency */ + switch (voltdm->sys_clk.rate) { + case 38400000: + hsscll = i2c_data->hsscll_38_4; + break; + case 26000000: + hsscll = i2c_data->hsscll_26; + break; + case 19200000: + hsscll = i2c_data->hsscll_19_2; + break; + case 16800000: + hsscll = i2c_data->hsscll_16_8; + break; + case 12000000: + hsscll = i2c_data->hsscll_12; + break; + default: + pr_warn("%s: unsupported sysclk rate: %d!\n", __func__, + voltdm->sys_clk.rate); + return; + } - /* XXX These are magic numbers and do not belong! */ - vc_val = (0x60 << OMAP4430_SCLL_SHIFT | 0x26 << OMAP4430_SCLH_SHIFT); - voltdm->write(vc_val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET); + /* Loadbits define pull setup for the I2C channels */ + val = i2c_data->loadbits << 25 | i2c_data->loadbits << 29; - is_initialized = true; + /* Write to SYSCTRL_PADCONF_WKUP_CTRL_I2C_2 to setup I2C pull */ + __raw_writel(val, OMAP2_L4_IO_ADDRESS(OMAP4_CTRL_MODULE_PAD_WKUP + + OMAP4_CTRL_MODULE_PAD_WKUP_CONTROL_I2C_2)); + + /* HSSCLH can always be zero */ + val = hsscll << OMAP4430_HSSCLL_SHIFT; + val |= (0x28 << OMAP4430_SCLL_SHIFT | 0x2c << OMAP4430_SCLH_SHIFT); + + /* Write setup times to I2C config register */ + voltdm->write(val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET); } + + /** * omap_vc_i2c_init - initialize I2C interface to PMIC * @voltdm: voltage domain containing VC data @@ -281,9 +636,49 @@ static void __init omap_vc_i2c_init(struct voltagedomain *voltdm) mcode << __ffs(vc->common->i2c_mcode_mask), vc->common->i2c_cfg_reg); + if (cpu_is_omap44xx()) + omap4_vc_i2c_timing_init(voltdm); + initialized = true; } +/** + * omap_vc_calc_vsel - calculate vsel value for a channel + * @voltdm: channel to calculate value for + * @uvolt: microvolt value to convert to vsel + * + * Converts a microvolt value to vsel value for the used PMIC. + * This checks whether the microvolt value is out of bounds, and + * adjusts the value accordingly. If unsupported value detected, + * warning is thrown. + */ +static u8 omap_vc_calc_vsel(struct voltagedomain *voltdm, u32 uvolt) +{ + if (voltdm->pmic->vddmin > uvolt) + uvolt = voltdm->pmic->vddmin; + if (voltdm->pmic->vddmax < uvolt) { + WARN(1, "%s: voltage not supported by pmic: %u vs max %u\n", + __func__, uvolt, voltdm->pmic->vddmax); + /* Lets try maximum value anyway */ + uvolt = voltdm->pmic->vddmax; + } + + return voltdm->pmic->uv_to_vsel(uvolt); +} + +/** + * omap_pm_setup_sr_i2c_pcb_length - set length of SR I2C traces on PCB + * @mm: length of the PCB trace in millimetres + * + * Sets the PCB trace length for the I2C channel. By default uses 63mm. + * This is needed for properly calculating the capacitance value for + * the PCB trace, and for setting the SR I2C channel timing parameters. + */ +void __init omap_pm_setup_sr_i2c_pcb_length(u32 mm) +{ + sr_i2c_pcb_length = mm; +} + void __init omap_vc_init_channel(struct voltagedomain *voltdm) { struct omap_vc_channel *vc = voltdm->vc; @@ -311,7 +706,6 @@ void __init omap_vc_init_channel(struct voltagedomain *voltdm) vc->i2c_slave_addr = voltdm->pmic->i2c_slave_addr; vc->volt_reg_addr = voltdm->pmic->volt_reg_addr; vc->cmd_reg_addr = voltdm->pmic->cmd_reg_addr; - vc->setup_time = voltdm->pmic->volt_setup_time; /* Configure the i2c slave address for this VC */ voltdm->rmw(vc->smps_sa_mask, @@ -331,14 +725,18 @@ void __init omap_vc_init_channel(struct voltagedomain *voltdm) voltdm->rmw(vc->smps_cmdra_mask, vc->cmd_reg_addr << __ffs(vc->smps_cmdra_mask), vc->smps_cmdra_reg); - vc->cfg_channel |= vc_cfg_bits->rac | vc_cfg_bits->racen; + vc->cfg_channel |= vc_cfg_bits->rac; } + if (vc->cmd_reg_addr == vc->volt_reg_addr) + vc->cfg_channel |= vc_cfg_bits->racen; + /* Set up the on, inactive, retention and off voltage */ - on_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->on_volt); - onlp_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->onlp_volt); - ret_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->ret_volt); - off_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->off_volt); + on_vsel = omap_vc_calc_vsel(voltdm, voltdm->vc_param->on); + onlp_vsel = omap_vc_calc_vsel(voltdm, voltdm->vc_param->onlp); + ret_vsel = omap_vc_calc_vsel(voltdm, voltdm->vc_param->ret); + off_vsel = omap_vc_calc_vsel(voltdm, voltdm->vc_param->off); + val = ((on_vsel << vc->common->cmd_on_shift) | (onlp_vsel << vc->common->cmd_onlp_shift) | (ret_vsel << vc->common->cmd_ret_shift) | @@ -349,11 +747,6 @@ void __init omap_vc_init_channel(struct voltagedomain *voltdm) /* Channel configuration */ omap_vc_config_channel(voltdm); - /* Configure the setup times */ - voltdm->rmw(voltdm->vfsm->voltsetup_mask, - vc->setup_time << __ffs(voltdm->vfsm->voltsetup_mask), - voltdm->vfsm->voltsetup_reg); - omap_vc_i2c_init(voltdm); if (cpu_is_omap34xx()) diff --git a/arch/arm/mach-omap2/vc.h b/arch/arm/mach-omap2/vc.h index 478bf6b432c4..91c8d75bf2ea 100644 --- a/arch/arm/mach-omap2/vc.h +++ b/arch/arm/mach-omap2/vc.h @@ -86,7 +86,6 @@ struct omap_vc_channel { u16 i2c_slave_addr; u16 volt_reg_addr; u16 cmd_reg_addr; - u16 setup_time; u8 cfg_channel; bool i2c_high_speed; @@ -111,6 +110,13 @@ extern struct omap_vc_channel omap4_vc_mpu; extern struct omap_vc_channel omap4_vc_iva; extern struct omap_vc_channel omap4_vc_core; +extern struct omap_vc_param omap3_mpu_vc_data; +extern struct omap_vc_param omap3_core_vc_data; + +extern struct omap_vc_param omap4_mpu_vc_data; +extern struct omap_vc_param omap4_iva_vc_data; +extern struct omap_vc_param omap4_core_vc_data; + void omap_vc_init_channel(struct voltagedomain *voltdm); int omap_vc_pre_scale(struct voltagedomain *voltdm, unsigned long target_volt, diff --git a/arch/arm/mach-omap2/vc3xxx_data.c b/arch/arm/mach-omap2/vc3xxx_data.c index 5d8eaf31569c..75bc4aa22b3a 100644 --- a/arch/arm/mach-omap2/vc3xxx_data.c +++ b/arch/arm/mach-omap2/vc3xxx_data.c @@ -71,3 +71,25 @@ struct omap_vc_channel omap3_vc_core = { .smps_cmdra_mask = OMAP3430_CMDRA1_MASK, .cfg_channel_sa_shift = OMAP3430_PRM_VC_SMPS_SA_SA1_SHIFT, }; + +/* + * Voltage levels for different operating modes: on, sleep, retention and off + */ +#define OMAP3_ON_VOLTAGE_UV 1200000 +#define OMAP3_ONLP_VOLTAGE_UV 1000000 +#define OMAP3_RET_VOLTAGE_UV 975000 +#define OMAP3_OFF_VOLTAGE_UV 600000 + +struct omap_vc_param omap3_mpu_vc_data = { + .on = OMAP3_ON_VOLTAGE_UV, + .onlp = OMAP3_ONLP_VOLTAGE_UV, + .ret = OMAP3_RET_VOLTAGE_UV, + .off = OMAP3_OFF_VOLTAGE_UV, +}; + +struct omap_vc_param omap3_core_vc_data = { + .on = OMAP3_ON_VOLTAGE_UV, + .onlp = OMAP3_ONLP_VOLTAGE_UV, + .ret = OMAP3_RET_VOLTAGE_UV, + .off = OMAP3_OFF_VOLTAGE_UV, +}; diff --git a/arch/arm/mach-omap2/vc44xx_data.c b/arch/arm/mach-omap2/vc44xx_data.c index d70b930f2739..085e5d6a04fd 100644 --- a/arch/arm/mach-omap2/vc44xx_data.c +++ b/arch/arm/mach-omap2/vc44xx_data.c @@ -87,3 +87,31 @@ struct omap_vc_channel omap4_vc_core = { .cfg_channel_sa_shift = OMAP4430_SA_VDD_CORE_L_SHIFT, }; +/* + * Voltage levels for different operating modes: on, sleep, retention and off + */ +#define OMAP4_ON_VOLTAGE_UV 1375000 +#define OMAP4_ONLP_VOLTAGE_UV 1375000 +#define OMAP4_RET_VOLTAGE_UV 837500 +#define OMAP4_OFF_VOLTAGE_UV 0 + +struct omap_vc_param omap4_mpu_vc_data = { + .on = OMAP4_ON_VOLTAGE_UV, + .onlp = OMAP4_ONLP_VOLTAGE_UV, + .ret = OMAP4_RET_VOLTAGE_UV, + .off = OMAP4_OFF_VOLTAGE_UV, +}; + +struct omap_vc_param omap4_iva_vc_data = { + .on = OMAP4_ON_VOLTAGE_UV, + .onlp = OMAP4_ONLP_VOLTAGE_UV, + .ret = OMAP4_RET_VOLTAGE_UV, + .off = OMAP4_OFF_VOLTAGE_UV, +}; + +struct omap_vc_param omap4_core_vc_data = { + .on = OMAP4_ON_VOLTAGE_UV, + .onlp = OMAP4_ONLP_VOLTAGE_UV, + .ret = OMAP4_RET_VOLTAGE_UV, + .off = OMAP4_OFF_VOLTAGE_UV, +}; diff --git a/arch/arm/mach-omap2/voltage.h b/arch/arm/mach-omap2/voltage.h index 7283b7ed7de8..a0ce4f10ff13 100644 --- a/arch/arm/mach-omap2/voltage.h +++ b/arch/arm/mach-omap2/voltage.h @@ -40,12 +40,14 @@ struct powerdomain; * data * @voltsetup_mask: SETUP_TIME* bitmask in the PRM_VOLTSETUP* register * @voltsetup_reg: register offset of PRM_VOLTSETUP from PRM base + * @voltsetup_off_reg: register offset of PRM_VOLTSETUP_OFF from PRM base * * XXX What about VOLTOFFSET/VOLTCTRL? */ struct omap_vfsm_instance { u32 voltsetup_mask; u8 voltsetup_reg; + u8 voltsetup_off_reg; }; /** @@ -74,6 +76,8 @@ struct voltagedomain { const struct omap_vfsm_instance *vfsm; struct omap_vp_instance *vp; struct omap_voltdm_pmic *pmic; + struct omap_vp_param *vp_param; + struct omap_vc_param *vc_param; /* VC/VP register access functions: SoC specific */ u32 (*read) (u8 offset); @@ -92,6 +96,24 @@ struct voltagedomain { struct omap_volt_data *volt_data; }; +/* Min and max voltages from OMAP perspective */ +#define OMAP3430_VP1_VLIMITTO_VDDMIN 850000 +#define OMAP3430_VP1_VLIMITTO_VDDMAX 1425000 +#define OMAP3430_VP2_VLIMITTO_VDDMIN 900000 +#define OMAP3430_VP2_VLIMITTO_VDDMAX 1150000 + +#define OMAP3630_VP1_VLIMITTO_VDDMIN 900000 +#define OMAP3630_VP1_VLIMITTO_VDDMAX 1350000 +#define OMAP3630_VP2_VLIMITTO_VDDMIN 900000 +#define OMAP3630_VP2_VLIMITTO_VDDMAX 1200000 + +#define OMAP4_VP_MPU_VLIMITTO_VDDMIN 830000 +#define OMAP4_VP_MPU_VLIMITTO_VDDMAX 1410000 +#define OMAP4_VP_IVA_VLIMITTO_VDDMIN 830000 +#define OMAP4_VP_IVA_VLIMITTO_VDDMAX 1260000 +#define OMAP4_VP_CORE_VLIMITTO_VDDMIN 830000 +#define OMAP4_VP_CORE_VLIMITTO_VDDMAX 1200000 + /** * struct omap_voltdm_pmic - PMIC specific data required by voltage driver. * @slew_rate: PMIC slew rate (in uv/us) @@ -107,26 +129,34 @@ struct voltagedomain { struct omap_voltdm_pmic { int slew_rate; int step_size; - u32 on_volt; - u32 onlp_volt; - u32 ret_volt; - u32 off_volt; - u16 volt_setup_time; u16 i2c_slave_addr; u16 volt_reg_addr; u16 cmd_reg_addr; u8 vp_erroroffset; u8 vp_vstepmin; u8 vp_vstepmax; - u8 vp_vddmin; - u8 vp_vddmax; + u32 vddmin; + u32 vddmax; u8 vp_timeout_us; bool i2c_high_speed; + u32 i2c_pad_load; u8 i2c_mcode; unsigned long (*vsel_to_uv) (const u8 vsel); u8 (*uv_to_vsel) (unsigned long uV); }; +struct omap_vp_param { + u32 vddmax; + u32 vddmin; +}; + +struct omap_vc_param { + u32 on; + u32 onlp; + u32 ret; + u32 off; +}; + void omap_voltage_get_volttable(struct voltagedomain *voltdm, struct omap_volt_data **volt_data); struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm, diff --git a/arch/arm/mach-omap2/voltagedomains3xxx_data.c b/arch/arm/mach-omap2/voltagedomains3xxx_data.c index 63afbfed3cbc..261bb7cb4e60 100644 --- a/arch/arm/mach-omap2/voltagedomains3xxx_data.c +++ b/arch/arm/mach-omap2/voltagedomains3xxx_data.c @@ -117,6 +117,11 @@ void __init omap3xxx_voltagedomains_init(void) } #endif + omap3_voltdm_mpu.vp_param = &omap3_mpu_vp_data; + omap3_voltdm_core.vp_param = &omap3_core_vp_data; + omap3_voltdm_mpu.vc_param = &omap3_mpu_vc_data; + omap3_voltdm_core.vc_param = &omap3_core_vc_data; + if (soc_is_am35xx()) voltdms = voltagedomains_am35xx; else diff --git a/arch/arm/mach-omap2/voltagedomains44xx_data.c b/arch/arm/mach-omap2/voltagedomains44xx_data.c index c3115f6853d4..48b22a0a0c88 100644 --- a/arch/arm/mach-omap2/voltagedomains44xx_data.c +++ b/arch/arm/mach-omap2/voltagedomains44xx_data.c @@ -22,7 +22,7 @@ #include <linux/init.h> #include "common.h" - +#include "soc.h" #include "prm-regbits-44xx.h" #include "prm44xx.h" #include "prcm44xx.h" @@ -34,14 +34,17 @@ static const struct omap_vfsm_instance omap4_vdd_mpu_vfsm = { .voltsetup_reg = OMAP4_PRM_VOLTSETUP_MPU_RET_SLEEP_OFFSET, + .voltsetup_off_reg = OMAP4_PRM_VOLTSETUP_MPU_OFF_OFFSET, }; static const struct omap_vfsm_instance omap4_vdd_iva_vfsm = { .voltsetup_reg = OMAP4_PRM_VOLTSETUP_IVA_RET_SLEEP_OFFSET, + .voltsetup_off_reg = OMAP4_PRM_VOLTSETUP_IVA_OFF_OFFSET, }; static const struct omap_vfsm_instance omap4_vdd_core_vfsm = { .voltsetup_reg = OMAP4_PRM_VOLTSETUP_CORE_RET_SLEEP_OFFSET, + .voltsetup_off_reg = OMAP4_PRM_VOLTSETUP_CORE_OFF_OFFSET, }; static struct voltagedomain omap4_voltdm_mpu = { @@ -101,11 +104,25 @@ void __init omap44xx_voltagedomains_init(void) * for the currently-running IC */ #ifdef CONFIG_PM_OPP - omap4_voltdm_mpu.volt_data = omap44xx_vdd_mpu_volt_data; - omap4_voltdm_iva.volt_data = omap44xx_vdd_iva_volt_data; - omap4_voltdm_core.volt_data = omap44xx_vdd_core_volt_data; + if (cpu_is_omap443x()) { + omap4_voltdm_mpu.volt_data = omap443x_vdd_mpu_volt_data; + omap4_voltdm_iva.volt_data = omap443x_vdd_iva_volt_data; + omap4_voltdm_core.volt_data = omap443x_vdd_core_volt_data; + } else if (cpu_is_omap446x()) { + omap4_voltdm_mpu.volt_data = omap446x_vdd_mpu_volt_data; + omap4_voltdm_iva.volt_data = omap446x_vdd_iva_volt_data; + omap4_voltdm_core.volt_data = omap446x_vdd_core_volt_data; + } #endif + omap4_voltdm_mpu.vp_param = &omap4_mpu_vp_data; + omap4_voltdm_iva.vp_param = &omap4_iva_vp_data; + omap4_voltdm_core.vp_param = &omap4_core_vp_data; + + omap4_voltdm_mpu.vc_param = &omap4_mpu_vc_data; + omap4_voltdm_iva.vc_param = &omap4_iva_vc_data; + omap4_voltdm_core.vc_param = &omap4_core_vc_data; + for (i = 0; voltdm = voltagedomains_omap4[i], voltdm; i++) voltdm->sys_clk.name = sys_clk_name; diff --git a/arch/arm/mach-omap2/vp.c b/arch/arm/mach-omap2/vp.c index 85241b828c02..a3c30655aa30 100644 --- a/arch/arm/mach-omap2/vp.c +++ b/arch/arm/mach-omap2/vp.c @@ -58,8 +58,10 @@ void __init omap_vp_init(struct voltagedomain *voltdm) sys_clk_rate = voltdm->sys_clk.rate / 1000; timeout = (sys_clk_rate * voltdm->pmic->vp_timeout_us) / 1000; - vddmin = voltdm->pmic->vp_vddmin; - vddmax = voltdm->pmic->vp_vddmax; + vddmin = max(voltdm->vp_param->vddmin, voltdm->pmic->vddmin); + vddmax = min(voltdm->vp_param->vddmax, voltdm->pmic->vddmax); + vddmin = voltdm->pmic->uv_to_vsel(vddmin); + vddmax = voltdm->pmic->uv_to_vsel(vddmax); waittime = DIV_ROUND_UP(voltdm->pmic->step_size * sys_clk_rate, 1000 * voltdm->pmic->slew_rate); @@ -138,7 +140,7 @@ int omap_vp_forceupdate_scale(struct voltagedomain *voltdm, udelay(1); } if (timeout >= VP_TRANXDONE_TIMEOUT) { - pr_warn("%s: vdd_%s TRANXDONE timeout exceeded. Voltage change aborted", + pr_warn("%s: vdd_%s TRANXDONE timeout exceeded. Voltage change aborted\n", __func__, voltdm->name); return -ETIMEDOUT; } @@ -197,7 +199,7 @@ void omap_vp_enable(struct voltagedomain *voltdm) u32 vpconfig, volt; if (!voltdm || IS_ERR(voltdm)) { - pr_warning("%s: VDD specified does not exist!\n", __func__); + pr_warn("%s: VDD specified does not exist!\n", __func__); return; } @@ -214,8 +216,8 @@ void omap_vp_enable(struct voltagedomain *voltdm) volt = voltdm_get_voltage(voltdm); if (!volt) { - pr_warning("%s: unable to find current voltage for %s\n", - __func__, voltdm->name); + pr_warn("%s: unable to find current voltage for %s\n", + __func__, voltdm->name); return; } @@ -242,7 +244,7 @@ void omap_vp_disable(struct voltagedomain *voltdm) int timeout; if (!voltdm || IS_ERR(voltdm)) { - pr_warning("%s: VDD specified does not exist!\n", __func__); + pr_warn("%s: VDD specified does not exist!\n", __func__); return; } @@ -272,8 +274,7 @@ void omap_vp_disable(struct voltagedomain *voltdm) VP_IDLE_TIMEOUT, timeout); if (timeout >= VP_IDLE_TIMEOUT) - pr_warning("%s: vdd_%s idle timedout\n", - __func__, voltdm->name); + pr_warn("%s: vdd_%s idle timedout\n", __func__, voltdm->name); vp->enabled = false; diff --git a/arch/arm/mach-omap2/vp.h b/arch/arm/mach-omap2/vp.h index 7c155d248aa3..0fdf7080e4a6 100644 --- a/arch/arm/mach-omap2/vp.h +++ b/arch/arm/mach-omap2/vp.h @@ -117,6 +117,13 @@ extern struct omap_vp_instance omap4_vp_mpu; extern struct omap_vp_instance omap4_vp_iva; extern struct omap_vp_instance omap4_vp_core; +extern struct omap_vp_param omap3_mpu_vp_data; +extern struct omap_vp_param omap3_core_vp_data; + +extern struct omap_vp_param omap4_mpu_vp_data; +extern struct omap_vp_param omap4_iva_vp_data; +extern struct omap_vp_param omap4_core_vp_data; + void omap_vp_init(struct voltagedomain *voltdm); void omap_vp_enable(struct voltagedomain *voltdm); void omap_vp_disable(struct voltagedomain *voltdm); diff --git a/arch/arm/mach-omap2/vp3xxx_data.c b/arch/arm/mach-omap2/vp3xxx_data.c index bd89f80089f5..1914e026245e 100644 --- a/arch/arm/mach-omap2/vp3xxx_data.c +++ b/arch/arm/mach-omap2/vp3xxx_data.c @@ -77,3 +77,13 @@ struct omap_vp_instance omap3_vp_core = { .vstatus = OMAP3_PRM_VP2_STATUS_OFFSET, .voltage = OMAP3_PRM_VP2_VOLTAGE_OFFSET, }; + +struct omap_vp_param omap3_mpu_vp_data = { + .vddmin = OMAP3430_VP1_VLIMITTO_VDDMIN, + .vddmax = OMAP3430_VP1_VLIMITTO_VDDMAX, +}; + +struct omap_vp_param omap3_core_vp_data = { + .vddmin = OMAP3430_VP2_VLIMITTO_VDDMIN, + .vddmax = OMAP3430_VP2_VLIMITTO_VDDMAX, +}; diff --git a/arch/arm/mach-omap2/vp44xx_data.c b/arch/arm/mach-omap2/vp44xx_data.c index 8c031d16879e..e62f6b018beb 100644 --- a/arch/arm/mach-omap2/vp44xx_data.c +++ b/arch/arm/mach-omap2/vp44xx_data.c @@ -87,3 +87,18 @@ struct omap_vp_instance omap4_vp_core = { .vstatus = OMAP4_PRM_VP_CORE_STATUS_OFFSET, .voltage = OMAP4_PRM_VP_CORE_VOLTAGE_OFFSET, }; + +struct omap_vp_param omap4_mpu_vp_data = { + .vddmin = OMAP4_VP_MPU_VLIMITTO_VDDMIN, + .vddmax = OMAP4_VP_MPU_VLIMITTO_VDDMAX, +}; + +struct omap_vp_param omap4_iva_vp_data = { + .vddmin = OMAP4_VP_IVA_VLIMITTO_VDDMIN, + .vddmax = OMAP4_VP_IVA_VLIMITTO_VDDMAX, +}; + +struct omap_vp_param omap4_core_vp_data = { + .vddmin = OMAP4_VP_CORE_VLIMITTO_VDDMIN, + .vddmax = OMAP4_VP_CORE_VLIMITTO_VDDMAX, +}; |