summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt22
-rw-r--r--Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt14
-rw-r--r--Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt50
-rw-r--r--Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt2
-rw-r--r--Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt179
-rw-r--r--Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt6
-rw-r--r--Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt13
-rw-r--r--Documentation/pinctrl.txt14
8 files changed, 263 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index 02ab5ab198a4..b7a93e80a302 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -19,6 +19,7 @@ such as pull-up, multi drive, etc.
Required properties for iomux controller:
- compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
+ or "atmel,sama5d3-pinctrl"
- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
configured in this periph mode. All the periph and bank need to be describe.
@@ -85,13 +86,20 @@ Required properties for pin configuration node:
PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
Bits used for CONFIG:
-PULL_UP (1 << 0): indicate this pin need a pull up.
-MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive.
-DEGLITCH (1 << 2): indicate this pin need deglitch.
-PULL_DOWN (1 << 3): indicate this pin need a pull down.
-DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger.
-DEBOUNCE (1 << 16): indicate this pin need debounce.
-DEBOUNCE_VAL (0x3fff << 17): debounce val.
+PULL_UP (1 << 0): indicate this pin needs a pull up.
+MULTIDRIVE (1 << 1): indicate this pin needs to be configured as multi-drive.
+ Multi-drive is equivalent to open-drain type output.
+DEGLITCH (1 << 2): indicate this pin needs deglitch.
+PULL_DOWN (1 << 3): indicate this pin needs a pull down.
+DIS_SCHMIT (1 << 4): indicate this pin needs to the disable schmitt trigger.
+DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the
+ following values:
+ 00 - No change (reset state value kept)
+ 01 - Low
+ 10 - Medium
+ 11 - High
+DEBOUNCE (1 << 16): indicate this pin needs debounce.
+DEBOUNCE_VAL (0x3fff << 17): debounce value.
NOTE:
Some requirements for using atmel,at91rm9200-pinctrl binding:
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
index 6464bf769460..189814e7cdc7 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
@@ -10,6 +10,7 @@ Required properties:
- reg: Should contain a list of base address and size pairs for:
-- first entry - the drive strength and pad control registers.
-- second entry - the pinmux registers
+ -- third entry - the MIPI_PAD_CTRL register
Tegra124 adds the following optional properties for pin configuration subnodes.
The macros for options are defined in the
@@ -91,6 +92,12 @@ Valid values for pin and group names are:
dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg,
gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4.
+ MIPI pad control groups:
+
+ These support only the nvidia,function property.
+
+ dsi_b
+
Valid values for nvidia,functions are:
blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya,
@@ -101,14 +108,15 @@ Valid values for nvidia,functions are:
sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta,
uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6,
vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1,
- dp, rtck, sys, clk tmds.
+ dp, rtck, sys, clk tmds, csi, dsi_b
Example:
pinmux: pinmux {
compatible = "nvidia,tegra124-pinmux";
- reg = <0x70000868 0x164 /* Pad control registers */
- 0x70003000 0x434>; /* PinMux registers */
+ reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */
+ <0x0 0x70003000 0x0 0x434>, /* Mux registers */
+ <0x0 0x70000820 0x0 0x8>; /* MIPI pad control */
};
Example pinmux entries:
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index fa40a177164c..98eb94d91a1c 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -127,6 +127,24 @@ whether there is any interaction between the child and intermediate parent
nodes, is again defined entirely by the binding for the individual pin
controller device.
+== Generic pin multiplexing node content ==
+
+pin multiplexing nodes:
+
+function - the mux function to select
+groups - the list of groups to select with this function
+
+Example:
+
+state_0_node_a {
+ function = "uart0";
+ groups = "u0rxtx", "u0rtscts";
+};
+state_1_node_a {
+ function = "spi0";
+ groups = "spi0pins";
+};
+
== Generic pin configuration node content ==
Many data items that are represented in a pin configuration node are common
@@ -139,8 +157,12 @@ structure of the DT nodes that contain these properties.
Supported generic properties are:
pins - the list of pins that properties in the node
- apply to
-function - the mux function to select
+ apply to (either this or "group" has to be
+ specified)
+group - the group to apply the properties to, if the driver
+ supports configuration of whole groups rather than
+ individual pins (either this or "pins" has to be
+ specified)
bias-disable - disable any pin bias
bias-high-impedance - high impedance mode ("third-state", "floating")
bias-bus-hold - latch weakly
@@ -163,6 +185,21 @@ output-low - set the pin to output mode with low level
output-high - set the pin to output mode with high level
slew-rate - set the slew rate
+For example:
+
+state_0_node_a {
+ pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ bias-pull-up;
+};
+state_1_node_a {
+ pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+ output-high;
+};
+state_2_node_a {
+ group = "foo-group";
+ bias-pull-up;
+};
+
Some of the generic properties take arguments. For those that do, the
arguments are described below.
@@ -170,15 +207,6 @@ arguments are described below.
binding for the hardware defines:
- Whether the entries are integers or strings, and their meaning.
-- function takes a list of function names/IDs as a required argument. The
- specific binding for the hardware defines:
- - Whether the entries are integers or strings, and their meaning.
- - Whether only a single entry is allowed (which is applied to all entries
- in the pins property), or whether there may alternatively be one entry per
- entry in the pins property, in which case the list lengths must match, and
- for each list index i, the function at list index i is applied to the pin
- at list index i.
-
- bias-pull-up, -down and -pin-default take as optional argument on hardware
supporting it the pull strength in Ohm. bias-disable will disable the pull.
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
index 92fae82f35f2..2fb90b37aa09 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
@@ -50,7 +50,7 @@ Valid values for function are:
gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
- riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic,
+ riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold
Example:
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
new file mode 100644
index 000000000000..ffafa1990a30
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
@@ -0,0 +1,179 @@
+Qualcomm APQ8084 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8960 platform.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,apq8084-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ gpio0-gpio146,
+ sdc1_clk,
+ sdc1_cmd,
+ sdc1_data
+ sdc2_clk,
+ sdc2_cmd,
+ sdc2_data
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Functions are only valid for gpio pins.
+ Valid values are:
+ adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3,
+ blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8,
+ blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
+ blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5,
+ blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
+ blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3,
+ blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8,
+ blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12,
+ blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5,
+ blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10,
+ blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2,
+ cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1,
+ cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+ edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i
+ gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio,
+ hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic,
+ ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst,
+ pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s,
+ qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n,
+ sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus,
+ spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1,
+ tsif2, uim, uim_batt_alarm
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+ Not valid for sdc pins.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+ Not valid for sdc pins.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ tlmm: pinctrl@fd510000 {
+ compatible = "qcom,apq8084-pinctrl";
+ reg = <0xfd510000 0x4000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <0 208 0>;
+
+ uart2: uart2-default {
+ mux {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart2";
+ };
+
+ tx {
+ pins = "gpio4";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
index 4658b69d4f4d..388b213249fd 100644
--- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
@@ -2,8 +2,8 @@
The Rockchip Pinmux Controller, enables the IC
to share one PAD to several functional blocks. The sharing is done by
-multiplexing the PAD input/output signals. For each PAD there are up to
-4 muxing options with option 0 being the use as a GPIO.
+multiplexing the PAD input/output signals. For each PAD there are several
+muxing options with option 0 being the use as a GPIO.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
@@ -58,7 +58,7 @@ Deprecated properties for gpio sub nodes:
Required properties for pin configuration node:
- rockchip,pins: 3 integers array, represents a group of pins mux and config
setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>.
- The MUX 0 means gpio and MUX 1 to 3 mean the specific device function.
+ The MUX 0 means gpio and MUX 1 to N mean the specific device function.
The phandle of a node containing the generic pinconfig options
to use, as described in pinctrl-bindings.txt in this directory.
diff --git a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
new file mode 100644
index 000000000000..88c80273da91
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
@@ -0,0 +1,13 @@
+OMAP Pinctrl definitions
+
+Required properties:
+- compatible : Should be one of:
+ "ti,omap2420-padconf" - OMAP2420 compatible pinctrl
+ "ti,omap2430-padconf" - OMAP2430 compatible pinctrl
+ "ti,omap3-padconf" - OMAP3 compatible pinctrl
+ "ti,omap4-padconf" - OMAP4 compatible pinctrl
+ "ti,omap5-padconf" - OMAP5 compatible pinctrl
+ "ti,dra7-padconf" - DRA7 compatible pinctrl
+ "ti,am437-padconf" - AM437x compatible pinctrl
+
+See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details.
diff --git a/Documentation/pinctrl.txt b/Documentation/pinctrl.txt
index 23f1590f49fe..b8f2147b96dd 100644
--- a/Documentation/pinctrl.txt
+++ b/Documentation/pinctrl.txt
@@ -702,7 +702,7 @@ static int foo_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
return 0;
}
-int foo_enable(struct pinctrl_dev *pctldev, unsigned selector,
+int foo_set_mux(struct pinctrl_dev *pctldev, unsigned selector,
unsigned group)
{
u8 regbit = (1 << selector + group);
@@ -711,21 +711,11 @@ int foo_enable(struct pinctrl_dev *pctldev, unsigned selector,
return 0;
}
-void foo_disable(struct pinctrl_dev *pctldev, unsigned selector,
- unsigned group)
-{
- u8 regbit = (1 << selector + group);
-
- writeb((readb(MUX) & ~(regbit)), MUX)
- return 0;
-}
-
struct pinmux_ops foo_pmxops = {
.get_functions_count = foo_get_functions_count,
.get_function_name = foo_get_fname,
.get_function_groups = foo_get_groups,
- .enable = foo_enable,
- .disable = foo_disable,
+ .set_mux = foo_set_mux,
};
/* Pinmux operations are handled by some pin controller */