diff options
Diffstat (limited to 'Documentation')
7 files changed, 79 insertions, 53 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index 6db22103e2dd..025cf8c9324a 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -36,7 +36,7 @@ Optional properties: control gpios - threshold: allows setting the "click"-threshold in the range - from 20 to 80. + from 0 to 80. - gain: allows setting the sensitivity in the range from 0 to 31. Note that lower values indicate higher diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt index 05485699d70e..9630ac0e4b56 100644 --- a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -16,6 +16,11 @@ Required properties: - reg: Base address of PMIC on Hi6220 SoC. - interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). - pmic-gpios: The GPIO used by PMIC IRQ. +- #clock-cells: From common clock binding; shall be set to 0 + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name Example: pmic: pmic@f8000000 { @@ -24,4 +29,5 @@ Example: interrupt-controller; #interrupt-cells = <2>; pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + #clock-cells = <0>; } diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt index e25436861867..9029b45b8a22 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt @@ -18,6 +18,8 @@ Optional properties: "ext_clock" (External clock provided to the card). - post-power-on-delay-ms : Delay in ms after powering the card and de-asserting the reset-gpios (if any) +- power-off-delay-us : Delay in us after asserting the reset-gpios (if any) + during power off of the card. Example: diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index a1e3693cca16..6f55bdd52f8a 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -15,6 +15,10 @@ Optional properties: - phy-reset-active-high : If present then the reset sequence using the GPIO specified in the "phy-reset-gpios" property is reversed (H=reset state, L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - phy-supply : regulator that powers the Ethernet PHY. - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 71a3c134af1b..f01d154090da 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -247,7 +247,6 @@ bias-bus-hold - latch weakly bias-pull-up - pull up the pin bias-pull-down - pull down the pin bias-pull-pin-default - use pin-default pull state -bi-directional - pin supports simultaneous input/output operations drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source @@ -260,7 +259,6 @@ input-debounce - debounce mode with debound time X power-source - select between different power supplies low-power-enable - enable low power mode low-power-disable - disable low power mode -output-enable - enable output on pin regardless of output value output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level slew-rate - set the slew rate diff --git a/Documentation/input/devices/edt-ft5x06.rst b/Documentation/input/devices/edt-ft5x06.rst index 2032f0b7a8fa..1ccc94b192b7 100644 --- a/Documentation/input/devices/edt-ft5x06.rst +++ b/Documentation/input/devices/edt-ft5x06.rst @@ -15,7 +15,7 @@ It has been tested with the following devices: The driver allows configuration of the touch screen via a set of sysfs files: /sys/class/input/eventX/device/device/threshold: - allows setting the "click"-threshold in the range from 20 to 80. + allows setting the "click"-threshold in the range from 0 to 80. /sys/class/input/eventX/device/device/gain: allows setting the sensitivity in the range from 0 to 31. Note that diff --git a/Documentation/sound/hd-audio/models.rst b/Documentation/sound/hd-audio/models.rst index 5338673c88d9..773d2bfacc6c 100644 --- a/Documentation/sound/hd-audio/models.rst +++ b/Documentation/sound/hd-audio/models.rst @@ -16,6 +16,8 @@ ALC880 6-jack in back, 2-jack in front 6stack-digout 6-jack with a SPDIF out +6stack-automute + 6-jack with headphone jack detection ALC260 ====== @@ -62,6 +64,8 @@ lenovo-dock Enables docking station I/O for some Lenovos hp-gpio-led GPIO LED support on HP laptops +hp-dock-gpio-mic1-led + HP dock with mic LED support dell-headset-multi Headset jack, which can also be used as mic-in dell-headset-dock @@ -72,6 +76,12 @@ alc283-sense-combo Combo jack sensing on ALC283 tpt440-dock Pin configs for Lenovo Thinkpad Dock support +tpt440 + Lenovo Thinkpad T440s setup +tpt460 + Lenovo Thinkpad T460/560 setup +dual-codecs + Lenovo laptops with dual codecs ALC66x/67x/892 ============== @@ -97,6 +107,8 @@ inv-dmic Inverted internal mic workaround dell-headset-multi Headset jack, which can also be used as mic-in +dual-codecs + Lenovo laptops with dual codecs ALC680 ====== @@ -114,6 +126,8 @@ inv-dmic Inverted internal mic workaround no-primary-hp VAIO Z/VGC-LN51JGB workaround (for fixed speaker DAC) +dual-codecs + ALC1220 dual codecs for Gaming mobos ALC861/660 ========== @@ -206,65 +220,47 @@ auto Conexant 5045 ============= -laptop-hpsense - Laptop with HP sense (old model laptop) -laptop-micsense - Laptop with Mic sense (old model fujitsu) -laptop-hpmicsense - Laptop with HP and Mic senses -benq - Benq R55E -laptop-hp530 - HP 530 laptop -test - for testing/debugging purpose, almost all controls can be - adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y +cap-mix-amp + Fix max input level on mixer widget +toshiba-p105 + Toshiba P105 quirk +hp-530 + HP 530 quirk Conexant 5047 ============= -laptop - Basic Laptop config -laptop-hp - Laptop config for some HP models (subdevice 30A5) -laptop-eapd - Laptop config with EAPD support -test - for testing/debugging purpose, almost all controls can be - adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y +cap-mix-amp + Fix max input level on mixer widget Conexant 5051 ============= -laptop - Basic Laptop config (default) -hp - HP Spartan laptop -hp-dv6736 - HP dv6736 -hp-f700 - HP Compaq Presario F700 -ideapad - Lenovo IdeaPad laptop -toshiba - Toshiba Satellite M300 +lenovo-x200 + Lenovo X200 quirk Conexant 5066 ============= -laptop - Basic Laptop config (default) -hp-laptop - HP laptops, e g G60 -asus - Asus K52JU, Lenovo G560 -dell-laptop - Dell laptops -dell-vostro - Dell Vostro -olpc-xo-1_5 - OLPC XO 1.5 -ideapad - Lenovo IdeaPad U150 +stereo-dmic + Workaround for inverted stereo digital mic +gpio1 + Enable GPIO1 pin +headphone-mic-pin + Enable headphone mic NID 0x18 without detection +tp410 + Thinkpad T400 & co quirks thinkpad - Lenovo Thinkpad + Thinkpad mute/mic LED quirk +lemote-a1004 + Lemote A1004 quirk +lemote-a1205 + Lemote A1205 quirk +olpc-xo + OLPC XO quirk +mute-led-eapd + Mute LED control via EAPD +hp-dock + HP dock support +mute-led-gpio + Mute LED control via GPIO STAC9200 ======== @@ -444,6 +440,8 @@ dell-eq Dell desktops/laptops alienware Alienware M17x +asus-mobo + Pin configs for ASUS mobo with 5.1/SPDIF out auto BIOS setup (default) @@ -477,6 +475,8 @@ hp-envy-ts-bass Pin fixup for HP Envy TS bass speaker (NID 0x10) hp-bnb13-eq Hardware equalizer setup for HP laptops +hp-envy-ts-bass + HP Envy TS bass support auto BIOS setup (default) @@ -496,10 +496,22 @@ auto Cirrus Logic CS4206/4207 ======================== +mbp53 + MacBook Pro 5,3 mbp55 MacBook Pro 5,5 imac27 IMac 27 Inch +imac27_122 + iMac 12,2 +apple + Generic Apple quirk +mbp101 + MacBookPro 10,1 +mbp81 + MacBookPro 8,1 +mba42 + MacBookAir 4,2 auto BIOS setup (default) @@ -509,6 +521,10 @@ mba6 MacBook Air 6,1 and 6,2 gpio0 Enable GPIO 0 amp +mbp11 + MacBookPro 11,2 +macmini + MacMini 7,1 auto BIOS setup (default) |