summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/devicetree/bindings/crypto/mv_cesa.txt20
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-fan.txt25
-rw-r--r--arch/arm/boot/dts/kirkwood-dnskw.dtsi10
-rw-r--r--arch/arm/boot/dts/kirkwood-iconnect.dts50
-rw-r--r--arch/arm/boot/dts/kirkwood.dtsi12
-rw-r--r--arch/arm/mach-kirkwood/board-dnskw.c26
-rw-r--r--arch/arm/mach-kirkwood/board-dt.c2
-rw-r--r--arch/arm/mach-kirkwood/board-iconnect.c48
-rw-r--r--drivers/crypto/mv_cesa.c17
-rw-r--r--drivers/hwmon/gpio-fan.c120
10 files changed, 251 insertions, 79 deletions
diff --git a/Documentation/devicetree/bindings/crypto/mv_cesa.txt b/Documentation/devicetree/bindings/crypto/mv_cesa.txt
new file mode 100644
index 000000000000..47229b1a594b
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/mv_cesa.txt
@@ -0,0 +1,20 @@
+Marvell Cryptographic Engines And Security Accelerator
+
+Required properties:
+- compatible : should be "marvell,orion-crypto"
+- reg : base physical address of the engine and length of memory mapped
+ region, followed by base physical address of sram and its memory
+ length
+- reg-names : "regs" , "sram";
+- interrupts : interrupt number
+
+Examples:
+
+ crypto@30000 {
+ compatible = "marvell,orion-crypto";
+ reg = <0x30000 0x10000>,
+ <0x4000000 0x800>;
+ reg-names = "regs" , "sram";
+ interrupts = <22>;
+ status = "okay";
+ };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
new file mode 100644
index 000000000000..2dd457a3469a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
@@ -0,0 +1,25 @@
+Bindings for fan connected to GPIO lines
+
+Required properties:
+- compatible : "gpio-fan"
+- gpios: Specifies the pins that map to bits in the control value,
+ ordered MSB-->LSB.
+- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
+ control value that should be set to achieve them. This array
+ must have the RPM values in ascending order.
+
+Optional properties:
+- alarm-gpios: This pin going active indicates something is wrong with
+ the fan, and a udev event will be fired.
+
+Examples:
+
+ gpio_fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio1 14 1
+ &gpio1 13 1>;
+ gpio-fan,speed-map = <0 0
+ 3000 1
+ 6000 2>;
+ alarm-gpios = <&gpio1 15 1>;
+ };
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
index 7408655f91b5..9b32d0272825 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
@@ -25,6 +25,16 @@
};
};
+ gpio_fan {
+ /* Fan: ADDA AD045HB-G73 40mm 6000rpm@5v */
+ compatible = "gpio-fan";
+ gpios = <&gpio1 14 1
+ &gpio1 13 1>;
+ gpio-fan,speed-map = <0 0
+ 3000 1
+ 6000 2>;
+ };
+
ocp@f1000000 {
sata@80000 {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index f8ca6fa88192..d97cd9d4753e 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -12,7 +12,7 @@
};
chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)";
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
linux,initrd-start = <0x4500040>;
linux,initrd-end = <0x4800000>;
};
@@ -30,7 +30,37 @@
clock-frequency = <200000000>;
status = "ok";
};
+
+ nand@3000000 {
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0xc0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ };
+
+ partition@100000 {
+ label = "zImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@540000 {
+ label = "initrd";
+ reg = <0x540000 0x300000>;
+ };
+
+ partition@980000 {
+ label = "boot";
+ reg = <0x980000 0x1f400000>;
+ };
+ };
};
+
gpio-leds {
compatible = "gpio-leds";
@@ -69,4 +99,22 @@
gpios = <&gpio1 16 0>;
};
};
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ button@1 {
+ label = "OTB Button";
+ linux,code = <133>;
+ gpios = <&gpio1 3 1>;
+ debounce-interval = <100>;
+ };
+ button@2 {
+ label = "Reset";
+ linux,code = <0x198>;
+ gpios = <&gpio0 12 1>;
+ debounce-interval = <100>;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index cef9616f330a..4e5b8154a5be 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -14,7 +14,8 @@
ocp@f1000000 {
compatible = "simple-bus";
- ranges = <0 0xf1000000 0x4000000>;
+ ranges = <0x00000000 0xf1000000 0x4000000
+ 0xf5000000 0xf5000000 0x0000400>;
#address-cells = <1>;
#size-cells = <1>;
@@ -105,5 +106,14 @@
clock-frequency = <100000>;
status = "disabled";
};
+
+ crypto@30000 {
+ compatible = "marvell,orion-crypto";
+ reg = <0x30000 0x10000>,
+ <0xf5000000 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <22>;
+ status = "okay";
+ };
};
};
diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c
index 4ab35065a144..6ac7a8dc7b78 100644
--- a/arch/arm/mach-kirkwood/board-dnskw.c
+++ b/arch/arm/mach-kirkwood/board-dnskw.c
@@ -19,7 +19,6 @@
#include <linux/of.h>
#include <linux/gpio.h>
#include <linux/input.h>
-#include <linux/gpio-fan.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -67,29 +66,6 @@ static unsigned int dnskw_mpp_config[] __initdata = {
0
};
-/* Fan: ADDA AD045HB-G73 40mm 6000rpm@5v */
-static struct gpio_fan_speed dnskw_fan_speed[] = {
- { 0, 0 },
- { 3000, 1 },
- { 6000, 2 },
-};
-static unsigned dnskw_fan_pins[] = {46, 45};
-
-static struct gpio_fan_platform_data dnskw_fan_data = {
- .num_ctrl = ARRAY_SIZE(dnskw_fan_pins),
- .ctrl = dnskw_fan_pins,
- .num_speed = ARRAY_SIZE(dnskw_fan_speed),
- .speed = dnskw_fan_speed,
-};
-
-static struct platform_device dnskw_fan_device = {
- .name = "gpio-fan",
- .id = -1,
- .dev = {
- .platform_data = &dnskw_fan_data,
- },
-};
-
static void dnskw_power_off(void)
{
gpio_set_value(36, 1);
@@ -114,8 +90,6 @@ void __init dnskw_init(void)
kirkwood_ehci_init();
kirkwood_ge00_init(&dnskw_ge00_data);
- platform_device_register(&dnskw_fan_device);
-
/* Register power-off GPIO. */
if (gpio_request(36, "dnskw:power:off") == 0
&& gpio_direction_output(36, 0) == 0)
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 496554664e08..70c5a2882409 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -33,6 +33,7 @@ struct of_dev_auxdata kirkwood_auxdata_lookup[] __initdata = {
OF_DEV_AUXDATA("marvell,orion-wdt", 0xf1020300, "orion_wdt", NULL),
OF_DEV_AUXDATA("marvell,orion-sata", 0xf1080000, "sata_mv.0", NULL),
OF_DEV_AUXDATA("marvell,orion-nand", 0xf4000000, "orion_nand", NULL),
+ OF_DEV_AUXDATA("marvell,orion-crypto", 0xf1030000, "mv_crypto", NULL),
{},
};
@@ -60,7 +61,6 @@ static void __init kirkwood_dt_init(void)
/* internal devices that every board has */
kirkwood_xor0_init();
kirkwood_xor1_init();
- kirkwood_crypto_init();
#ifdef CONFIG_KEXEC
kexec_reinit = kirkwood_enable_pcie;
diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
index d7a9198ed300..d084b1e2943a 100644
--- a/arch/arm/mach-kirkwood/board-iconnect.c
+++ b/arch/arm/mach-kirkwood/board-iconnect.c
@@ -16,11 +16,8 @@
#include <linux/of_fdt.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
-#include <linux/mtd/partitions.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include "common.h"
@@ -44,57 +41,12 @@ static unsigned int iconnect_mpp_config[] __initdata = {
0
};
-static struct mtd_partition iconnect_nand_parts[] = {
- {
- .name = "flash",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-/* yikes... theses are the original input buttons */
-/* but I'm not convinced by the sw event choices */
-static struct gpio_keys_button iconnect_buttons[] = {
- {
- .type = EV_SW,
- .code = SW_LID,
- .gpio = 12,
- .desc = "Reset Button",
- .active_low = 1,
- .debounce_interval = 100,
- }, {
- .type = EV_SW,
- .code = SW_TABLET_MODE,
- .gpio = 35,
- .desc = "OTB Button",
- .active_low = 1,
- .debounce_interval = 100,
- },
-};
-
-static struct gpio_keys_platform_data iconnect_button_data = {
- .buttons = iconnect_buttons,
- .nbuttons = ARRAY_SIZE(iconnect_buttons),
-};
-
-static struct platform_device iconnect_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &iconnect_button_data,
- },
-};
-
void __init iconnect_init(void)
{
kirkwood_mpp_conf(iconnect_mpp_config);
- kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
kirkwood_ehci_init();
kirkwood_ge00_init(&iconnect_ge00_data);
-
- platform_device_register(&iconnect_button_device);
}
static int __init iconnect_pci_init(void)
diff --git a/drivers/crypto/mv_cesa.c b/drivers/crypto/mv_cesa.c
index 21c1a87032b7..24ccae453e79 100644
--- a/drivers/crypto/mv_cesa.c
+++ b/drivers/crypto/mv_cesa.c
@@ -19,6 +19,9 @@
#include <linux/clk.h>
#include <crypto/internal/hash.h>
#include <crypto/sha.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
#include "mv_cesa.h"
@@ -1062,7 +1065,10 @@ static int mv_probe(struct platform_device *pdev)
goto err_unmap_reg;
}
- irq = platform_get_irq(pdev, 0);
+ if (pdev->dev.of_node)
+ irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+ else
+ irq = platform_get_irq(pdev, 0);
if (irq < 0 || irq == NO_IRQ) {
ret = irq;
goto err_unmap_sram;
@@ -1170,12 +1176,19 @@ static int mv_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id mv_cesa_of_match_table[] = {
+ { .compatible = "marvell,orion-crypto", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, mv_cesa_of_match_table);
+
static struct platform_driver marvell_crypto = {
.probe = mv_probe,
- .remove = mv_remove,
+ .remove = __devexit_p(mv_remove),
.driver = {
.owner = THIS_MODULE,
.name = "mv_crypto",
+ .of_match_table = of_match_ptr(mv_cesa_of_match_table),
},
};
MODULE_ALIAS("platform:mv_crypto");
diff --git a/drivers/hwmon/gpio-fan.c b/drivers/hwmon/gpio-fan.c
index 2f4b01bda87c..36509ae32083 100644
--- a/drivers/hwmon/gpio-fan.c
+++ b/drivers/hwmon/gpio-fan.c
@@ -31,6 +31,8 @@
#include <linux/hwmon.h>
#include <linux/gpio.h>
#include <linux/gpio-fan.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
struct gpio_fan_data {
struct platform_device *pdev;
@@ -400,14 +402,131 @@ static ssize_t show_name(struct device *dev,
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
+#ifdef CONFIG_OF_GPIO
+/*
+ * Translate OpenFirmware node properties into platform_data
+ */
+static int gpio_fan_get_of_pdata(struct device *dev,
+ struct gpio_fan_platform_data *pdata)
+{
+ struct device_node *node;
+ struct gpio_fan_speed *speed;
+ unsigned *ctrl;
+ unsigned i;
+ u32 u;
+ struct property *prop;
+ const __be32 *p;
+
+ node = dev->of_node;
+
+ /* Fill GPIO pin array */
+ pdata->num_ctrl = of_gpio_count(node);
+ if (!pdata->num_ctrl) {
+ dev_err(dev, "gpios DT property empty / missing");
+ return -ENODEV;
+ }
+ ctrl = devm_kzalloc(dev, pdata->num_ctrl * sizeof(unsigned),
+ GFP_KERNEL);
+ if (!ctrl)
+ return -ENOMEM;
+ for (i = 0; i < pdata->num_ctrl; i++) {
+ int val;
+
+ val = of_get_gpio(node, i);
+ if (val < 0)
+ return val;
+ ctrl[i] = val;
+ }
+ pdata->ctrl = ctrl;
+
+ /* Get number of RPM/ctrl_val pairs in speed map */
+ prop = of_find_property(node, "gpio-fan,speed-map", &i);
+ if (!prop) {
+ dev_err(dev, "gpio-fan,speed-map DT property missing");
+ return -ENODEV;
+ }
+ i = i / sizeof(u32);
+ if (i == 0 || i & 1) {
+ dev_err(dev, "gpio-fan,speed-map contains zero/odd number of entries");
+ return -ENODEV;
+ }
+ pdata->num_speed = i / 2;
+
+ /*
+ * Populate speed map
+ * Speed map is in the form <RPM ctrl_val RPM ctrl_val ...>
+ * this needs splitting into pairs to create gpio_fan_speed structs
+ */
+ speed = devm_kzalloc(dev,
+ pdata->num_speed * sizeof(struct gpio_fan_speed),
+ GFP_KERNEL);
+ if (!speed)
+ return -ENOMEM;
+ p = NULL;
+ for (i = 0; i < pdata->num_speed; i++) {
+ p = of_prop_next_u32(prop, p, &u);
+ if (!p)
+ return -ENODEV;
+ speed[i].rpm = u;
+ p = of_prop_next_u32(prop, p, &u);
+ if (!p)
+ return -ENODEV;
+ speed[i].ctrl_val = u;
+ }
+ pdata->speed = speed;
+
+ /* Alarm GPIO if one exists */
+ if (of_gpio_named_count(node, "alarm-gpios")) {
+ struct gpio_fan_alarm *alarm;
+ int val;
+ enum of_gpio_flags flags;
+
+ alarm = devm_kzalloc(dev, sizeof(struct gpio_fan_alarm),
+ GFP_KERNEL);
+ if (!alarm)
+ return -ENOMEM;
+
+ val = of_get_named_gpio_flags(node, "alarm-gpios", 0, &flags);
+ if (val < 0)
+ return val;
+ alarm->gpio = val;
+ alarm->active_low = flags & OF_GPIO_ACTIVE_LOW;
+
+ pdata->alarm = alarm;
+ }
+
+ return 0;
+}
+
+static struct of_device_id of_gpio_fan_match[] __devinitdata = {
+ { .compatible = "gpio-fan", },
+ {},
+};
+#endif /* CONFIG_OF_GPIO */
+
static int __devinit gpio_fan_probe(struct platform_device *pdev)
{
int err;
struct gpio_fan_data *fan_data;
struct gpio_fan_platform_data *pdata = pdev->dev.platform_data;
+#ifdef CONFIG_OF_GPIO
+ if (!pdata) {
+ pdata = devm_kzalloc(&pdev->dev,
+ sizeof(struct gpio_fan_platform_data),
+ GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ err = gpio_fan_get_of_pdata(&pdev->dev, pdata);
+ if (err)
+ return err;
+ }
+#else /* CONFIG_OF_GPIO */
if (!pdata)
return -EINVAL;
+#endif /* CONFIG_OF_GPIO */
fan_data = devm_kzalloc(&pdev->dev, sizeof(struct gpio_fan_data),
GFP_KERNEL);
@@ -511,6 +630,7 @@ static struct platform_driver gpio_fan_driver = {
.driver = {
.name = "gpio-fan",
.pm = GPIO_FAN_PM,
+ .of_match_table = of_match_ptr(of_gpio_fan_match),
},
};