Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

1 files changed, 3 insertions, 95 deletions

diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index bba5a560e02b..feb65787c30b 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -31,6 +31,7 @@
 
 #include <mach/board.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/stamp9g20.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -38,11 +39,7 @@
 
 static void __init pcontrol_g20_map_io(void)
 {
-	/* Initialize processor: 18.432 MHz crystal */
-	at91sam9260_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
-	at91_register_uart(0, 0, 0);
+	stamp9g20_map_io();
 
 	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
 	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
@@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void)
 
 	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
 	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 
@@ -66,38 +60,6 @@ static void __init init_irq(void)
 }
 
 
-/*
- * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
- */
-static struct atmel_nand_data __initdata nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-};
-
-/*
- * Bus timings; unit = 7.57ns
- */
-static struct sam9_smc_config __initdata nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 3,
-};
-
 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 	.ncs_read_setup		= 16,
 	.nrd_setup		= 18,
@@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 	.tdf_cycles		= 1,
 } };
 
-static void __init add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &nand_smc_config);
-	at91_add_device_nand(&nand_data);
-}
-
-
 static void __init add_device_pcontrol(void)
 {
 	/* configure chip-select 4 (IO compatible to 8051  X4 ) */
@@ -156,23 +110,6 @@ static void __init add_device_pcontrol(void)
 
 
 /*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-static struct mci_platform_data __initdata mmc_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-	},
-};
-#else
-static struct at91_mmc_data __initdata mmc_data = {
-	.wire4		= 1,
-};
-#endif
-
-
-/*
  * USB Host port
  */
 static struct at91_usbh_data __initdata usbh_data = {
@@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = {
 };
 
 
-/*
- * Dallas 1-Wire  DS2431
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	.pin		= AT91_PIN_PA29,
-	.is_open_drain	= 1,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-static void add_wire1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-
 static void __init pcontrol_g20_board_init(void)
 {
-	at91_add_device_serial();
-	add_device_nand();
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-	at91_add_device_mci(0, &mmc_data);
-#else
-	at91_add_device_mmc(0, &mmc_data);
-#endif
+	stamp9g20_board_init();
 	at91_add_device_usbh(&usbh_data);
 	at91_add_device_eth(&macb_data);
 	at91_add_device_i2c(pcontrol_g20_i2c_devices,
 		ARRAY_SIZE(pcontrol_g20_i2c_devices));
-	add_wire1();
 	add_device_pcontrol();
 	at91_add_device_spi(pcontrol_g20_spi_devices,
 		ARRAY_SIZE(pcontrol_g20_spi_devices));