summaryrefslogtreecommitdiff
path: root/drivers/usb/host/ehci-tegra.c
blob: 5f0a98e8b80b59f79372e2185e31e16585c6dd7f (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
/*
 * Copyright (c) 2011 The Chromium OS Authors.
 * Copyright (c) 2009-2013 NVIDIA Corporation
 * Copyright (c) 2013 Lucas Stach
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <asm-generic/gpio.h>
#include <asm/arch/clock.h>
#include <asm/arch-tegra/usb.h>
#include <asm/arch-tegra/clk_rst.h>
#include <usb.h>
#include <usb/ulpi.h>
#include <libfdt.h>
#include <fdtdec.h>

#include "ehci.h"

#define USB1_ADDR_MASK	0xFFFF0000

#define HOSTPC1_DEVLC	0x84
#define HOSTPC1_PSPD(x)		(((x) >> 25) & 0x3)

#ifdef CONFIG_USB_ULPI
	#ifndef CONFIG_USB_ULPI_VIEWPORT
	#error	"To use CONFIG_USB_ULPI on Tegra Boards you have to also \
		define CONFIG_USB_ULPI_VIEWPORT"
	#endif
#endif

enum {
	USB_PORTS_MAX	= 3,		/* Maximum ports we allow */
};

/* Parameters we need for USB */
enum {
	PARAM_DIVN,                     /* PLL FEEDBACK DIVIDer */
	PARAM_DIVM,                     /* PLL INPUT DIVIDER */
	PARAM_DIVP,                     /* POST DIVIDER (2^N) */
	PARAM_CPCON,                    /* BASE PLLC CHARGE Pump setup ctrl */
	PARAM_LFCON,                    /* BASE PLLC LOOP FILter setup ctrl */
	PARAM_ENABLE_DELAY_COUNT,       /* PLL-U Enable Delay Count */
	PARAM_STABLE_COUNT,             /* PLL-U STABLE count */
	PARAM_ACTIVE_DELAY_COUNT,       /* PLL-U Active delay count */
	PARAM_XTAL_FREQ_COUNT,          /* PLL-U XTAL frequency count */
	PARAM_DEBOUNCE_A_TIME,          /* 10MS DELAY for BIAS_DEBOUNCE_A */
	PARAM_BIAS_TIME,                /* 20US DELAY AFter bias cell op */

	PARAM_COUNT
};

/* Possible port types (dual role mode) */
enum dr_mode {
	DR_MODE_NONE = 0,
	DR_MODE_HOST,		/* supports host operation */
	DR_MODE_DEVICE,		/* supports device operation */
	DR_MODE_OTG,		/* supports both */
};

/* Information about a USB port */
struct fdt_usb {
	struct usb_ctlr *reg;	/* address of registers in physical memory */
	unsigned utmi:1;	/* 1 if port has external tranceiver, else 0 */
	unsigned ulpi:1;	/* 1 if port has external ULPI transceiver */
	unsigned enabled:1;	/* 1 to enable, 0 to disable */
	unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */
	unsigned initialized:1; /* has this port already been initialized? */
	enum usb_init_type init_type;
	enum dr_mode dr_mode;	/* dual role mode */
	enum periph_id periph_id;/* peripheral id */
	struct fdt_gpio_state vbus_gpio;	/* GPIO for vbus enable */
	struct fdt_gpio_state phy_reset_gpio; /* GPIO to reset ULPI phy */
};

static struct fdt_usb port[USB_PORTS_MAX];	/* List of valid USB ports */
static unsigned port_count;			/* Number of available ports */
/* Port that needs to clear CSC after Port Reset */
static u32 port_addr_clear_csc;

/*
 * This table has USB timing parameters for each Oscillator frequency we
 * support. There are four sets of values:
 *
 * 1. PLLU configuration information (reference clock is osc/clk_m and
 * PLLU-FOs are fixed at 12MHz/60MHz/480MHz).
 *
 *  Reference frequency     13.0MHz      19.2MHz      12.0MHz      26.0MHz
 *  ----------------------------------------------------------------------
 *      DIVN                960 (0x3c0)  200 (0c8)    960 (3c0h)   960 (3c0)
 *      DIVM                13 (0d)      4 (04)       12 (0c)      26 (1a)
 * Filter frequency (MHz)   1            4.8          6            2
 * CPCON                    1100b        0011b        1100b        1100b
 * LFCON0                   0            0            0            0
 *
 * 2. PLL CONFIGURATION & PARAMETERS for different clock generators:
 *
 * Reference frequency     13.0MHz         19.2MHz         12.0MHz     26.0MHz
 * ---------------------------------------------------------------------------
 * PLLU_ENABLE_DLY_COUNT   02 (0x02)       03 (03)         02 (02)     04 (04)
 * PLLU_STABLE_COUNT       51 (33)         75 (4B)         47 (2F)    102 (66)
 * PLL_ACTIVE_DLY_COUNT    05 (05)         06 (06)         04 (04)     09 (09)
 * XTAL_FREQ_COUNT        127 (7F)        187 (BB)        118 (76)    254 (FE)
 *
 * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and
 * SessEnd. Each of these signals have their own debouncer and for each of
 * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or
 * BIAS_DEBOUNCE_B).
 *
 * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows:
 *    0xffff -> No debouncing at all
 *    <n> ms = <n> *1000 / (1/19.2MHz) / 4
 *
 * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have:
 * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4  = 4800 = 0x12c0
 *
 * We need to use only DebounceA for BOOTROM. We don't need the DebounceB
 * values, so we can keep those to default.
 *
 * 4. The 20 microsecond delay after bias cell operation.
 */
static const unsigned T20_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   0,  0x02, 0x33, 0x05, 0x7F, 0x7EF4, 5 },
	{ 0x0C8, 0x04, 0x00, 0x3,   0,  0x03, 0x4B, 0x06, 0xBB, 0xBB80, 7 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   0,  0x02, 0x2F, 0x04, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   0,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }
};

static const unsigned T30_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   1,  0x02, 0x33, 0x09, 0x7F, 0x7EF4, 5 },
	{ 0x0C8, 0x04, 0x00, 0x3,   0,  0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 7 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   1,  0x02, 0x2F, 0x08, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   1,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }
};

static const unsigned T114_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   2,  0x02, 0x33, 0x09, 0x7F, 0x7EF4, 6 },
	{ 0x0C8, 0x04, 0x00, 0x3,   2,  0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 8 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   2,  0x02, 0x2F, 0x08, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   2,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 0xB }
};

/* UTMIP Idle Wait Delay */
static const u8 utmip_idle_wait_delay = 17;

/* UTMIP Elastic limit */
static const u8 utmip_elastic_limit = 16;

/* UTMIP High Speed Sync Start Delay */
static const u8 utmip_hs_sync_start_delay = 9;

struct fdt_usb_controller {
	int compat;
	/* flag to determine whether controller supports hostpc register */
	u32 has_hostpc:1;
	const unsigned *pll_parameter;
};

static struct fdt_usb_controller fdt_usb_controllers[] = {
	{
		.compat		= COMPAT_NVIDIA_TEGRA20_USB,
		.has_hostpc	= 0,
		.pll_parameter	= (const unsigned *)T20_usb_pll,
	},
	{
		.compat		= COMPAT_NVIDIA_TEGRA30_USB,
		.has_hostpc	= 1,
		.pll_parameter	= (const unsigned *)T30_usb_pll,
	},
	{
		.compat		= COMPAT_NVIDIA_TEGRA114_USB,
		.has_hostpc	= 1,
		.pll_parameter	= (const unsigned *)T114_usb_pll,
	},
};

static struct fdt_usb_controller *controller;

/*
 * A known hardware issue where Connect Status Change bit of PORTSC register
 * of USB1 controller will be set after Port Reset.
 * We have to clear it in order for later device enumeration to proceed.
 * This ehci_powerup_fixup overrides the weak function ehci_powerup_fixup
 * in "ehci-hcd.c".
 */
void ehci_powerup_fixup(uint32_t *status_reg, uint32_t *reg)
{
	mdelay(50);
	/* This is to avoid PORT_ENABLE bit to be cleared in "ehci-hcd.c". */
	if (controller->has_hostpc)
		*reg |= EHCI_PS_PE;

	if (((u32)status_reg & TEGRA_USB_ADDR_MASK) != port_addr_clear_csc)
		return;
	/* For EHCI_PS_CSC to be cleared in ehci_hcd.c */
	if (ehci_readl(status_reg) & EHCI_PS_CSC)
		*reg |= EHCI_PS_CSC;
}

/*
 * This ehci_set_usbmode overrides the weak function ehci_set_usbmode
 * in "ehci-hcd.c".
 */
void ehci_set_usbmode(int index)
{
	struct fdt_usb *config;
	struct usb_ctlr *usbctlr;
	uint32_t tmp;

	config = &port[index];
	usbctlr = config->reg;

	tmp = ehci_readl(&usbctlr->usb_mode);
	tmp |= USBMODE_CM_HC;
	ehci_writel(&usbctlr->usb_mode, tmp);
}

/*
 * This ehci_get_port_speed overrides the weak function ehci_get_port_speed
 * in "ehci-hcd.c".
 */
int ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg)
{
	uint32_t tmp;
	uint32_t *reg_ptr;

	if (controller->has_hostpc) {
		reg_ptr = (uint32_t *)((u8 *)&hcor->or_usbcmd + HOSTPC1_DEVLC);
		tmp = ehci_readl(reg_ptr);
		return HOSTPC1_PSPD(tmp);
	} else
		return PORTSC_PSPD(reg);
}

/* Set up VBUS for host/device mode */
static void set_up_vbus(struct fdt_usb *config, enum usb_init_type init)
{
	/*
	 * If we are an OTG port initializing in host mode,
	 * check if remote host is driving VBus and bail out in this case.
	 */
	if (init == USB_INIT_HOST &&
	    config->dr_mode == DR_MODE_OTG &&
	    (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)) {
		printf("tegrausb: VBUS input active; not enabling as host\n");
		return;
	}

	if (fdt_gpio_isvalid(&config->vbus_gpio)) {
		int vbus_value;

		fdtdec_setup_gpio(&config->vbus_gpio);

		vbus_value = (init == USB_INIT_HOST) ^
			     !!(config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW);
		gpio_direction_output(config->vbus_gpio.gpio, vbus_value);

		debug("set_up_vbus: GPIO %d %d\n", config->vbus_gpio.gpio,
		      vbus_value);
	}
}

void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr)
{
	/* Reset the USB controller with 2us delay */
	reset_periph(config->periph_id, 2);

	/*
	 * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under
	 * base address
	 */
	if (config->has_legacy_mode)
		setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE);

	/* Put UTMIP1/3 in reset */
	setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);

	/* Enable the UTMIP PHY */
	if (config->utmi)
		setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB);
}

static const unsigned *get_pll_timing(void)
{
	const unsigned *timing;

	timing = controller->pll_parameter +
		clock_get_osc_freq() * PARAM_COUNT;

	return timing;
}

/* select the PHY to use with a USB controller */
static void init_phy_mux(struct fdt_usb *config, uint pts,
			 enum usb_init_type init)
{
	struct usb_ctlr *usbctlr = config->reg;

#if defined(CONFIG_TEGRA20)
	if (config->periph_id == PERIPH_ID_USBD) {
		clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK,
				pts << PTS1_SHIFT);
		clrbits_le32(&usbctlr->port_sc1, STS1);
	} else {
		clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
				pts << PTS_SHIFT);
		clrbits_le32(&usbctlr->port_sc1, STS);
	}
#else
	/* Set to Host mode (if applicable) after Controller Reset was done */
	clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC,
			(init == USB_INIT_HOST) ? USBMODE_CM_HC : 0);
	/*
	 * Select PHY interface after setting host mode.
	 * For device mode, the ordering requirement is not an issue, since
	 * only the first USB controller supports device mode, and that USB
	 * controller can only talk to a UTMI PHY, so the PHY selection is
	 * already made at reset time, so this write is a no-op.
	 */
	clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK,
			pts << PTS_SHIFT);
	clrbits_le32(&usbctlr->hostpc1_devlc, STS);
#endif
}

/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config,
				    enum usb_init_type init)
{
	u32 b_sess_valid_mask, val;
	int loop_count;
	const unsigned *timing;
	struct usb_ctlr *usbctlr = config->reg;
	struct clk_rst_ctlr *clkrst;
	struct usb_ctlr *usb1ctlr;

	clock_enable(config->periph_id);

	/* Reset the usb controller */
	usbf_reset_controller(config, usbctlr);

	/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
	clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);

	/* Follow the crystal clock disable by >100ns delay */
	udelay(1);

	b_sess_valid_mask = (VBUS_B_SESS_VLD_SW_VALUE | VBUS_B_SESS_VLD_SW_EN);
	clrsetbits_le32(&usbctlr->phy_vbus_sensors, b_sess_valid_mask,
			(init == USB_INIT_DEVICE) ? b_sess_valid_mask : 0);

	/*
	 * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
	 * mux must be switched to actually use a_sess_vld threshold.
	 */
	if (config->dr_mode == DR_MODE_OTG &&
	    fdt_gpio_isvalid(&config->vbus_gpio))
		clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
			VBUS_SENSE_CTL_MASK,
			VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);

	/*
	 * PLL Delay CONFIGURATION settings. The following parameters control
	 * the bring up of the plls.
	 */
	timing = get_pll_timing();

	if (!controller->has_hostpc) {
		val = readl(&usbctlr->utmip_misc_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
				timing[PARAM_STABLE_COUNT] <<
				UTMIP_PLLU_STABLE_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
				timing[PARAM_ACTIVE_DELAY_COUNT] <<
				UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
		writel(val, &usbctlr->utmip_misc_cfg1);

		/* Set PLL enable delay count and crystal frequency count */
		val = readl(&usbctlr->utmip_pll_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
				timing[PARAM_ENABLE_DELAY_COUNT] <<
				UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
				timing[PARAM_XTAL_FREQ_COUNT] <<
				UTMIP_XTAL_FREQ_COUNT_SHIFT);
		writel(val, &usbctlr->utmip_pll_cfg1);
	} else {
		clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;

		val = readl(&clkrst->crc_utmip_pll_cfg2);
		clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
				timing[PARAM_STABLE_COUNT] <<
				UTMIP_PLLU_STABLE_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
				timing[PARAM_ACTIVE_DELAY_COUNT] <<
				UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
		writel(val, &clkrst->crc_utmip_pll_cfg2);

		/* Set PLL enable delay count and crystal frequency count */
		val = readl(&clkrst->crc_utmip_pll_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
				timing[PARAM_ENABLE_DELAY_COUNT] <<
				UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
				timing[PARAM_XTAL_FREQ_COUNT] <<
				UTMIP_XTAL_FREQ_COUNT_SHIFT);
		writel(val, &clkrst->crc_utmip_pll_cfg1);

		/* Disable Power Down state for PLL */
		clrbits_le32(&clkrst->crc_utmip_pll_cfg1,
			     PLLU_POWERDOWN | PLL_ENABLE_POWERDOWN |
			     PLL_ACTIVE_POWERDOWN);

		/* Recommended PHY settings for EYE diagram */
		val = readl(&usbctlr->utmip_xcvr_cfg0);
		clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MASK,
				0x4 << UTMIP_XCVR_SETUP_SHIFT);
		clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MSB_MASK,
				0x3 << UTMIP_XCVR_SETUP_MSB_SHIFT);
		clrsetbits_le32(&val, UTMIP_XCVR_HSSLEW_MSB_MASK,
				0x8 << UTMIP_XCVR_HSSLEW_MSB_SHIFT);
		writel(val, &usbctlr->utmip_xcvr_cfg0);
		clrsetbits_le32(&usbctlr->utmip_xcvr_cfg1,
				UTMIP_XCVR_TERM_RANGE_ADJ_MASK,
				0x7 << UTMIP_XCVR_TERM_RANGE_ADJ_SHIFT);

		/* Some registers can be controlled from USB1 only. */
		if (config->periph_id != PERIPH_ID_USBD) {
			clock_enable(PERIPH_ID_USBD);
			/* Disable Reset if in Reset state */
			reset_set_enable(PERIPH_ID_USBD, 0);
		}
		usb1ctlr = (struct usb_ctlr *)
			((u32)config->reg & USB1_ADDR_MASK);
		val = readl(&usb1ctlr->utmip_bias_cfg0);
		setbits_le32(&val, UTMIP_HSDISCON_LEVEL_MSB);
		clrsetbits_le32(&val, UTMIP_HSDISCON_LEVEL_MASK,
				0x1 << UTMIP_HSDISCON_LEVEL_SHIFT);
		clrsetbits_le32(&val, UTMIP_HSSQUELCH_LEVEL_MASK,
				0x2 << UTMIP_HSSQUELCH_LEVEL_SHIFT);
		writel(val, &usb1ctlr->utmip_bias_cfg0);

		/* Miscellaneous setting mentioned in Programming Guide */
		clrbits_le32(&usbctlr->utmip_misc_cfg0,
			     UTMIP_SUSPEND_EXIT_ON_EDGE);
	}

	/* Setting the tracking length time */
	clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
		UTMIP_BIAS_PDTRK_COUNT_MASK,
		timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);

	/* Program debounce time for VBUS to become valid */
	clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
		UTMIP_DEBOUNCE_CFG0_MASK,
		timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);

	setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J);

	/* Disable battery charge enabling bit */
	setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG);

	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE);
	setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL);

	/*
	 * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
	 * Setting these fields, together with default values of the
	 * other fields, results in programming the registers below as
	 * follows:
	 *         UTMIP_HSRX_CFG0 = 0x9168c000
	 *         UTMIP_HSRX_CFG1 = 0x13
	 */

	/* Set PLL enable delay count and Crystal frequency count */
	val = readl(&usbctlr->utmip_hsrx_cfg0);
	clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK,
		utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT);
	clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK,
		utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT);
	writel(val, &usbctlr->utmip_hsrx_cfg0);

	/* Configure the UTMIP_HS_SYNC_START_DLY */
	clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1,
		UTMIP_HS_SYNC_START_DLY_MASK,
		utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT);

	/* Preceed the crystal clock disable by >100ns delay. */
	udelay(1);

	/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
	setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);

	if (controller->has_hostpc) {
		if (config->periph_id == PERIPH_ID_USBD)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_A_POWERDOWN);
		if (config->periph_id == PERIPH_ID_USB2)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_B_POWERDOWN);
		if (config->periph_id == PERIPH_ID_USB3)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_C_POWERDOWN);
	}
	/* Finished the per-controller init. */

	/* De-assert UTMIP_RESET to bring out of reset. */
	clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);

	/* Wait for the phy clock to become valid in 100 ms */
	for (loop_count = 100000; loop_count != 0; loop_count--) {
		if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
			break;
		udelay(1);
	}
	if (!loop_count)
		return -1;

	/* Disable ICUSB FS/LS transceiver */
	clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);

	/* Select UTMI parallel interface */
	init_phy_mux(config, PTS_UTMI, init);

	/* Deassert power down state */
	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
		UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
	clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
		UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);

	if (controller->has_hostpc) {
		/*
		 * BIAS Pad Power Down is common among all 3 USB
		 * controllers and can be controlled from USB1 only.
		 */
		usb1ctlr = (struct usb_ctlr *)
			((u32)config->reg & USB1_ADDR_MASK);
		clrbits_le32(&usb1ctlr->utmip_bias_cfg0, UTMIP_BIASPD);
		udelay(25);
		clrbits_le32(&usb1ctlr->utmip_bias_cfg1,
			     UTMIP_FORCE_PDTRK_POWERDOWN);
	}
	return 0;
}

#ifdef CONFIG_USB_ULPI
/* if board file does not set a ULPI reference frequency we default to 24MHz */
#ifndef CONFIG_ULPI_REF_CLK
#define CONFIG_ULPI_REF_CLK 24000000
#endif

/* set up the ULPI USB controller with the parameters provided */
static int init_ulpi_usb_controller(struct fdt_usb *config,
				    enum usb_init_type init)
{
	u32 val;
	int loop_count;
	struct ulpi_viewport ulpi_vp;
	struct usb_ctlr *usbctlr = config->reg;

	/* set up ULPI reference clock on pllp_out4 */
	clock_enable(PERIPH_ID_DEV2_OUT);
	clock_set_pllout(CLOCK_ID_PERIPH, PLL_OUT4, CONFIG_ULPI_REF_CLK);

	/* reset ULPI phy */
	if (fdt_gpio_isvalid(&config->phy_reset_gpio)) {
		fdtdec_setup_gpio(&config->phy_reset_gpio);
		gpio_direction_output(config->phy_reset_gpio.gpio, 0);
		mdelay(5);
		gpio_set_value(config->phy_reset_gpio.gpio, 1);
	}

	/* Reset the usb controller */
	clock_enable(config->periph_id);
	usbf_reset_controller(config, usbctlr);

	/* enable pinmux bypass */
	setbits_le32(&usbctlr->ulpi_timing_ctrl_0,
			ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP);

	/* Select ULPI parallel interface */
	init_phy_mux(config, PTS_ULPI, init);

	/* enable ULPI transceiver */
	setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB);

	/* configure ULPI transceiver timings */
	val = 0;
	writel(val, &usbctlr->ulpi_timing_ctrl_1);

	val |= ULPI_DATA_TRIMMER_SEL(4);
	val |= ULPI_STPDIRNXT_TRIMMER_SEL(4);
	val |= ULPI_DIR_TRIMMER_SEL(4);
	writel(val, &usbctlr->ulpi_timing_ctrl_1);
	udelay(10);

	val |= ULPI_DATA_TRIMMER_LOAD;
	val |= ULPI_STPDIRNXT_TRIMMER_LOAD;
	val |= ULPI_DIR_TRIMMER_LOAD;
	writel(val, &usbctlr->ulpi_timing_ctrl_1);

	/* set up phy for host operation with external vbus supply */
	ulpi_vp.port_num = 0;
	ulpi_vp.viewport_addr = (u32)&usbctlr->ulpi_viewport;

	if (ulpi_init(&ulpi_vp)) {
		printf("Tegra ULPI viewport init failed\n");
		return -1;
	}

	ulpi_set_vbus(&ulpi_vp, 1, 1);
	ulpi_set_vbus_indicator(&ulpi_vp, 1, 1, 0);

	/* enable wakeup events */
	setbits_le32(&usbctlr->port_sc1, WKCN | WKDS | WKOC);

	/* Enable and wait for the phy clock to become valid in 100 ms */
	setbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
	for (loop_count = 100000; loop_count != 0; loop_count--) {
		if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
			break;
		udelay(1);
	}
	if (!loop_count)
		return -1;
	clrbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);

	return 0;
}
#else
static int init_ulpi_usb_controller(struct fdt_usb *config,
				    enum usb_init_type init)
{
	printf("No code to set up ULPI controller, please enable"
			"CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT");
	return -1;
}
#endif

static void config_clock(const u32 timing[])
{
	clock_start_pll(CLOCK_ID_USB,
		timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP],
		timing[PARAM_CPCON], timing[PARAM_LFCON]);
}

static int fdt_decode_usb(const void *blob, int node, struct fdt_usb *config)
{
	const char *phy, *mode;

	config->reg = (struct usb_ctlr *)fdtdec_get_addr(blob, node, "reg");
	mode = fdt_getprop(blob, node, "dr_mode", NULL);
	if (mode) {
		if (0 == strcmp(mode, "host"))
			config->dr_mode = DR_MODE_HOST;
		else if (0 == strcmp(mode, "peripheral"))
			config->dr_mode = DR_MODE_DEVICE;
		else if (0 == strcmp(mode, "otg"))
			config->dr_mode = DR_MODE_OTG;
		else {
			debug("%s: Cannot decode dr_mode '%s'\n", __func__,
			      mode);
			return -FDT_ERR_NOTFOUND;
		}
	} else {
		config->dr_mode = DR_MODE_HOST;
	}

	phy = fdt_getprop(blob, node, "phy_type", NULL);
	config->utmi = phy && 0 == strcmp("utmi", phy);
	config->ulpi = phy && 0 == strcmp("ulpi", phy);
	config->enabled = fdtdec_get_is_enabled(blob, node);
	config->has_legacy_mode = fdtdec_get_bool(blob, node,
						  "nvidia,has-legacy-mode");
	if (config->has_legacy_mode)
		port_addr_clear_csc = (u32) config->reg;
	config->periph_id = clock_decode_periph_id(blob, node);
	if (config->periph_id == PERIPH_ID_NONE) {
		debug("%s: Missing/invalid peripheral ID\n", __func__);
		return -FDT_ERR_NOTFOUND;
	}
	fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio);
	fdtdec_decode_gpio(blob, node, "nvidia,phy-reset-gpio",
			&config->phy_reset_gpio);
	debug("enabled=%d, legacy_mode=%d, utmi=%d, ulpi=%d, periph_id=%d, "
		"vbus=%d, phy_reset=%d, dr_mode=%d\n",
		config->enabled, config->has_legacy_mode, config->utmi,
		config->ulpi, config->periph_id, config->vbus_gpio.gpio,
		config->phy_reset_gpio.gpio, config->dr_mode);

	return 0;
}

/*
 * process_usb_nodes() - Process a list of USB nodes, adding them to our list
 *			of USB ports.
 * @blob:	fdt blob
 * @node_list:	list of nodes to process (any <=0 are ignored)
 * @count:	number of nodes to process
 *
 * Return:	0 - ok, -1 - error
 */
static int process_usb_nodes(const void *blob, int node_list[], int count)
{
	struct fdt_usb config;
	int node, i;
	int clk_done = 0;

	port_count = 0;
	for (i = 0; i < count; i++) {
		if (port_count == USB_PORTS_MAX) {
			printf("tegrausb: Cannot register more than %d ports\n",
				USB_PORTS_MAX);
			return -1;
		}

		debug("USB %d: ", i);
		node = node_list[i];
		if (!node)
			continue;
		if (fdt_decode_usb(blob, node, &config)) {
			debug("Cannot decode USB node %s\n",
			      fdt_get_name(blob, node, NULL));
			return -1;
		}
		if (!clk_done) {
			config_clock(get_pll_timing());
			clk_done = 1;
		}
		config.initialized = 0;

		/* add new USB port to the list of available ports */
		port[port_count++] = config;
	}

	return 0;
}

int usb_process_devicetree(const void *blob)
{
	int node_list[USB_PORTS_MAX];
	int count, err = 0;
	int i;

	for (i = 0; i < ARRAY_SIZE(fdt_usb_controllers); i++) {
		controller = &fdt_usb_controllers[i];

		count = fdtdec_find_aliases_for_id(blob, "usb",
			controller->compat, node_list, USB_PORTS_MAX);
		if (count) {
			err = process_usb_nodes(blob, node_list, count);
			if (err)
				printf("%s: Error processing USB node!\n",
				       __func__);
			return err;
		}
	}
	if (i == ARRAY_SIZE(fdt_usb_controllers))
		controller = NULL;

	return err;
}

/**
 * Start up the given port number (ports are numbered from 0 on each board).
 * This returns values for the appropriate hccr and hcor addresses to use for
 * USB EHCI operations.
 *
 * @param index	port number to start
 * @param hccr		returns start address of EHCI HCCR registers
 * @param hcor		returns start address of EHCI HCOR registers
 * @return 0 if ok, -1 on error (generally invalid port number)
 */
int ehci_hcd_init(int index, enum usb_init_type init,
		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
	struct fdt_usb *config;
	struct usb_ctlr *usbctlr;

	if (index >= port_count)
		return -1;

	config = &port[index];

	switch (init) {
	case USB_INIT_HOST:
		switch (config->dr_mode) {
		case DR_MODE_HOST:
		case DR_MODE_OTG:
			break;
		default:
			printf("tegrausb: Invalid dr_mode %d for host mode\n",
			       config->dr_mode);
			return -1;
		}
		break;
	case USB_INIT_DEVICE:
		if (config->periph_id != PERIPH_ID_USBD) {
			printf("tegrausb: Device mode only supported on first USB controller\n");
			return -1;
		}
		if (!config->utmi) {
			printf("tegrausb: Device mode only supported with UTMI PHY\n");
			return -1;
		}
		switch (config->dr_mode) {
		case DR_MODE_DEVICE:
		case DR_MODE_OTG:
			break;
		default:
			printf("tegrausb: Invalid dr_mode %d for device mode\n",
			       config->dr_mode);
			return -1;
		}
		break;
	default:
		printf("tegrausb: Unknown USB_INIT_* %d\n", init);
		return -1;
	}

	/* skip init, if the port is already initialized */
	if (config->initialized && config->init_type == init)
		goto success;

	if (config->utmi && init_utmi_usb_controller(config, init)) {
		printf("tegrausb: Cannot init port %d\n", index);
		return -1;
	}

	if (config->ulpi && init_ulpi_usb_controller(config, init)) {
		printf("tegrausb: Cannot init port %d\n", index);
		return -1;
	}

	set_up_vbus(config, init);

	config->initialized = 1;
	config->init_type = init;

success:
	usbctlr = config->reg;
	*hccr = (struct ehci_hccr *)&usbctlr->cap_length;
	*hcor = (struct ehci_hcor *)&usbctlr->usb_cmd;

	return 0;
}

/*
 * Bring down the specified USB controller
 */
int ehci_hcd_stop(int index)
{
	struct usb_ctlr *usbctlr;

	usbctlr = port[index].reg;

	/* Stop controller */
	writel(0, &usbctlr->usb_cmd);
	udelay(1000);

	/* Initiate controller reset */
	writel(2, &usbctlr->usb_cmd);
	udelay(1000);

	port[index].initialized = 0;

	return 0;
}