summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-01Make sure Freescale utilities are chmod +x before trying to execute them2009.03-mpc5125_twr-201009011610Scott Sweeny
2010-09-01Freescale board patch for MPC5125_TWR boardScott Sweeny
2010-08-30no inline and weak attributesScott Sweeny
2009-03-21Prepare 2009.03v2009.03Wolfgang Denk
Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-21Replaced endpoint numbers with appropriate macros in usbtty.c.Vivek Kutal
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-03-20.gitignore for generated files in api_examples directoryJon Smirl
Add .gitignore for generated files in api_examples directory Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-20net: sh_eth: Remove sh_eth_reset() from halt functionNobuhiro Iwamatsu
sh_eth_reset is function to reset Ether IP. The MAC address is stored in IP, but it is initialized by this function. OS (e.g. Linux Kernel) can not use this device when initialized. This revises this problem. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
2009-03-20ppc4xx: Fix bug in PCI outbound map configuration for canyonlandsAnatolij Gustschin
PCI outbound address map configuration doesn't match the PCI memory address range covered by appropriate TLB entry configuration for canyonlands causing machine check exceptions while accessing PCI memory regions. This patch provides a fix for this issue. Kazuaki Ichinohe observed and reported this issue while testing display output with PCI ATI video card on canyonlands. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-19CFI: geometry reversal for STMicro M29W320DTRichard Retanubun
Follow up to the flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip. The M29W320DT has 4 erase region. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-19smc911x_eeprom: update register APIMike Frysinger
The smc911x driver changed the naming convention for its register funcs, so update the eeprom code accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-18mpc52xx: Get rid of board-specific #ifdef's in cpu/mpc5xxx/ide.cGrzegorz Bernacki
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select. To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by Total5200 and will be used by digsy MTC and other boards with ATA CS on I2C pins. Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-188xx: add support for new keymile kmsupx4 board.Heiko Schocher
This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-188xx, mgsuvd: rename board to a more generic nameHeiko Schocher
renaming the "mgsuvd" board port into "km8xx", because there come more similar boards from keymile. Compiling the mgsuvd board with "make mgsuvd_config" remains. Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-188xx, mgsuvd: Coding Style cleanup config fileHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18powerpc: common updates for keymile boardsHeiko Schocher
- added to keymile-common.h: - bootcount support - COMMAND HISTORY - CONFIG_AUTO_COMPLETE - CONFIG_SYS_FLASH_PROTECTION - JFFS2 support - CONFIG_VERSION_VARIABLE - extracted common I2C settings for all boards - common default environment settings summarized Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-188xx, icache: enabling ICache not before running from RAMHeiko Schocher
with the new CONFIG_SYS_DELAYED_ICACHE config option, ICache is not enabled before code runs from RAM. Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-1882xx, mgcoge: fix environment sector sizeHeiko Schocher
Size of one environment sector is 0x20000. Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18NetStar: config reindentationLadislav Michl
Fix indentation broken by symbol renames. "Sort" driver related definitons. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-18Merge branch 'master' of git://git.denx.de/u-boot-coldfireWolfgang Denk
2009-03-18Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
2009-03-17ColdFire: Fix incorrect definitionTsiChung Liew
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17ColdFire: Fix M5329EVB and M5373EVB nand issueTsiChung Liew
The Nand flash was unable to read and write properly due to Nand Chip Select (nCE) setup was in reverse order. Also, increase the Nand time out value to 60. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17ColdFire: PLATFORM_CPPFLAGS updates for new compilerTsiChung Liew
Update PLATFORM_CPPFLAGS to accept 4.3.x version of ColdFire compiler. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17ColdFire: Provide gzip image size V2 & V3 platformsTsiChung Liew
Default gzip bootm size is 8MB. Some platforms require more than 8MB Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17ColdFire: Fix M54451 serial boot dram setupTsiChung Liew
The serial boot dram extended/standard mode register was not setup and was using default DRAM setup causing the U-boot was unstable to boot up in serial mode. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17Coldfire: XL Bus minor fixesarun c
According to coldfire manual data timeout > address time out also use correct macro to program XARB_CFG Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
2009-03-17NAND: Have nboot accept .e and .i as legacy no-ops.Scott Wood
This was intended to happen before, but a trivial bug prevented it. Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-17NAND: Make nboot skip bad blocksLadislav Michl
nboot command currently does not skip bad blocks and gives read error when loading image stored over bad block. With patch applied, nboot works as expected: Device 0 bad blocks: 00780000 014a0000 02000000 02cc0000 04aa0000 Loading from NAND 128MiB 3,3V 8-bit, offset 0x2c00000 Image Name: Linux-2.6.22-omap1 Created: 2008-11-20 23:44:32 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1052520 Bytes = 1 MB Load Address: 10008000 Entry Point: 10008000 Skipping bad block 0x02cc0000 Automatic boot of image at addr 0x10400000 ... ... Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-17ppc4xx: lwmon5: Only use one CS (rank) in DDR2 configurationStefan Roese
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with the DDR2 configuration to only use one CS (rank). As this code is most likely copied from the original Sequoia version, this error was copied as well. This patch also removes some dead code. Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17ppc4xx: PMC440: Only use one CS (rank) in DDR2 configurationStefan Roese
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with the DDR2 configuration to only use one CS (rank). As this code is most likely copied from the original Sequoia version, this error was copied as well. Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17Fix AMCC Sequoia board DDR memory configurationMikhail Zolotaryov
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D) specifies that BankSel#1 is not connected, while bootloader memory configuration is (board/amcc/sequoia/sdram.c): mtsdram(DDR0_10, 0x00000300); i.e. both Chip Selects used - not correct. If we change to correct value here: mtsdram(DDR0_10, 0x00000100); memory is accessible OK also. Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua> Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-15Prepare 2009.03-rc2v2009.03-rc2Wolfgang Denk
Update CHANEGLOG, fix minor coding style issue. Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-15Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2009-03-15Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2009-03-15Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-03-15Merge branch 'master' of git://git.denx.de/u-boot-pxaWolfgang Denk
2009-03-14mpc83xx: Add bank configuration to FSL spd_sdram.cJerry Van Baren
The routine assumed 4 bank SDRAMs, enhance to configure for 4 or 8 bank SDRAMs. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Acked-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-14mpc83xx: correctly set encryption and I2C bus 0 clockNorbert van Bolhuis
This patch makes sure the correct mask is applied when setting the encryption and I2C bus 0 clock in SCCR. Failing to do so may lead to ENCCM being 0 in which case I2C bus 0 won't function. Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-13OMAP3: Add support for OMAP3 die IDDirk Behme
Read and store OMAP3 die ID in U-Boot environment. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-03-13MPC5200 FEC MII speed registerJon Smirl
Set a non-zero speed in the MII register so that MII commands will work. Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
2009-03-13sh: ap325rxa: Change the wait cycle in the area 5Yusuke.Goda
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Fix cannot work rtl8139 on r2dplusYoshihiro Shimoda
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory registration. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add netdev header fixing of warning/buildNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add support 32-Bit Extended Address Mode to sh7785lcrYoshihiro Shimoda
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb" for this mode. This command changes PMB for using 512MB system memory. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add some register value configurable to PCI of SH7780Yoshihiro Shimoda
Some register value was hardcoded for System memory size 128MB and memory offset 0x08000000. This patch fixed the problem. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add system memory registration to PCI for SH4Yoshihiro Shimoda
It is necessary for some pci device driver. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add value for PCI system memory registration of sh7785lcrYoshihiro Shimoda
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: Add macros for SH-4A 32-Bit Address Extended ModeYoshihiro Shimoda
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12sh: use write{8,16,32} in ms7720se lowlevel_initNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-10Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-23 21:20:02 +0000