summaryrefslogtreecommitdiff
path: root/include/configs/PN62.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/PN62.h')
-rw-r--r--include/configs/PN62.h301
1 files changed, 301 insertions, 0 deletions
diff --git a/include/configs/PN62.h b/include/configs/PN62.h
new file mode 100644
index 0000000000..0750116246
--- /dev/null
+++ b/include/configs/PN62.h
@@ -0,0 +1,301 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC824X 1
+#define CONFIG_MPC8240 1
+#define CONFIG_PN62 1
+
+#define CONFIG_CONS_INDEX 1
+
+
+#define REMOVE_COMMANDS ( CFG_CMD_AUTOSCRIPT | \
+ CFG_CMD_LOADS | \
+ CFG_CMD_ENV | \
+ CFG_CMD_FLASH )
+
+#define CONFIG_COMMANDS ( (CONFIG_CMD_DFL & ~REMOVE_COMMANDS) |\
+ CFG_CMD_PCI |\
+ CFG_CMD_BSP)
+
+#define CONFIG_BAUDRATE 19200 /* console baudrate */
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after n seconds */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_SERVERIP 10.0.0.201
+#define CONFIG_IPADDR 10.0.0.200
+#define CONFIG_ROOTPATH /opt/eldk/ppc_82xx
+#define CONFIG_NETMASK 255.255.255.0
+#undef CONFIG_BOOTARGS
+#if 0
+/* Boot Linux with NFS root filesystem */
+#define CONFIG_BOOTCOMMAND \
+ "setenv verify y;" \
+ "setenv bootargs console=ttyS0,19200 mem=31M quiet " \
+ "root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip)::$(netmask):pn62:eth0:off;" \
+ "loadp 100000; bootm"
+ /* "tftpboot 100000 pImage; bootm" */
+#else
+/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
+#define CONFIG_BOOTCOMMAND \
+ "setenv verify n;" \
+ "setenv bootargs console=ttyS0,19200 mem=31M quiet " \
+ "root=/dev/ram rw " \
+ "ip=$(ipaddr):$(serverip)::$(netmask):pn62:eth0:off;" \
+ "loadp 200000; bootm"
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP 1 /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_PRAM 1024 /* reserve 1 MB protected RAM */
+
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+
+/*
+ * PCI stuff
+ */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP /* we need Plug 'n Play */
+#if 0
+#define CONFIG_PCI_SCAN_SHOW /* show PCI auto-scan at boot */
+#endif
+
+/*
+ * Networking stuff
+ */
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+
+#define CONFIG_PCNET /* there are 2 AMD PCnet 79C973 */
+#define CONFIG_PCNET_79C973
+
+#define _IO_BASE 0xfe000000 /* points to PCI I/O space */
+
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MAX_RAM_SIZE 0x10000000
+
+#define CFG_RESET_ADDRESS 0xfff00100
+
+#undef CFG_RAMBOOT
+#define CFG_MONITOR_LEN 0x00030000
+#define CFG_MONITOR_BASE TEXT_BASE
+
+/*#define CFG_GBL_DATA_SIZE 256*/
+#define CFG_GBL_DATA_SIZE 128
+
+#define CFG_INIT_RAM_ADDR 0x40000000
+#define CFG_INIT_RAM_END 0x1000
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+
+#define CFG_NO_FLASH 1 /* There is no FLASH memory */
+
+#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+#define CFG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
+
+#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
+
+#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
+#define CFG_MEMTEST_END 0x01f00000 /* 0 ... 32 MB in DRAM */
+
+/*
+ * Serial port configuration
+ */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+
+#define CFG_NS16550_REG_SIZE 1
+
+#define CFG_NS16550_CLK 1843200
+
+#define CFG_NS16550_COM1 0xff800008
+#define CFG_NS16550_COM2 0xff800000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3
+
+#define CFG_EUMB_ADDR 0xFCE00000
+
+/* MCCR1 */
+#define CFG_ROMNAL 3 /* rom/flash next access time */
+#define CFG_ROMFAL 7 /* rom/flash access time */
+
+/* MCCR2 */
+#define CFG_ASRISE 6 /* ASRISE in clocks */
+#define CFG_ASFALL 12 /* ASFALL in clocks */
+#define CFG_REFINT 5600 /* REFINT in clocks */
+
+/* MCCR3 */
+#define CFG_BSTOPRE 0x3cf /* Burst To Precharge */
+#define CFG_REFREC 2 /* Refresh to activate interval */
+#define CFG_RDLAT 3 /* data latency from read command */
+
+/* MCCR4 */
+#define CFG_PRETOACT 1 /* Precharge to activate interval */
+#define CFG_ACTTOPRE 3 /* Activate to Precharge interval */
+#define CFG_ACTORW 2 /* Activate to R/W */
+#define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */
+#define CFG_SDMODE_WRAP 0 /* SDMODE Wrap type */
+#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
+#define CFG_REGISTERD_TYPE_BUFFER 1
+
+/* Memory bank settings:
+ *
+ * only bits 20-29 are actually used from these vales to set the
+ * start/qend address the upper two bits will be 0, and the lower 20
+ * bits will be set to 0x00000 for a start address, or 0xfffff for an
+ * end address
+ */
+#define CFG_BANK0_START 0x00000000
+#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1)
+#define CFG_BANK0_ENABLE 1
+#define CFG_BANK1_START 0x00000000
+#define CFG_BANK1_END 0x00000000
+#define CFG_BANK1_ENABLE 0
+#define CFG_BANK2_START 0x00000000
+#define CFG_BANK2_END 0x00000000
+#define CFG_BANK2_ENABLE 0
+#define CFG_BANK3_START 0x00000000
+#define CFG_BANK3_END 0x00000000
+#define CFG_BANK3_ENABLE 0
+#define CFG_BANK4_START 0x00000000
+#define CFG_BANK4_END 0x00000000
+#define CFG_BANK4_ENABLE 0
+#define CFG_BANK5_START 0x00000000
+#define CFG_BANK5_END 0x00000000
+#define CFG_BANK5_ENABLE 0
+#define CFG_BANK6_START 0x00000000
+#define CFG_BANK6_END 0x00000000
+#define CFG_BANK6_ENABLE 0
+#define CFG_BANK7_START 0x00000000
+#define CFG_BANK7_END 0x00000000
+#define CFG_BANK7_ENABLE 0
+
+/*
+ * Memory bank enable bitmask, specifying which of the banks defined above
+ * are actually present. MSB is for bank #7, LSB is for bank #0.
+ */
+#define CFG_BANK_ENABLE 0x01
+
+#define CFG_ODCR 0xff /* configures line driver impedances, */
+ /* see 8240 book for bit definitions */
+#define CFG_PGMAX 0x32 /* how long the 8240 retains the */
+ /* currently accessed page in memory */
+ /* see 8240 book for details */
+
+/* SDRAM 0 - 256MB */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* PCI memory space */
+#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* Config addrs, etc */
+#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+#endif /* __CONFIG_H */