summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Makefile19
-rw-r--r--doc/README.sbc834950
-rw-r--r--include/configs/MPC8313ERDB.h4
-rw-r--r--include/configs/MPC8315ERDB.h4
-rw-r--r--include/configs/MPC8323ERDB.h4
-rw-r--r--include/configs/MPC832XEMDS.h4
-rw-r--r--include/configs/MPC8349EMDS.h5
-rw-r--r--include/configs/MPC8360EMDS.h4
-rw-r--r--include/configs/MPC837XEMDS.h4
-rw-r--r--include/configs/MPC837XERDB.h10
-rw-r--r--include/configs/TQM834x.h2
-rw-r--r--include/configs/sbc8349.h27
-rw-r--r--include/configs/vme8349.h5
-rw-r--r--include/mpc83xx.h3
14 files changed, 91 insertions, 54 deletions
diff --git a/Makefile b/Makefile
index 2636ac055e..96cca232be 100644
--- a/Makefile
+++ b/Makefile
@@ -2380,8 +2380,23 @@ MPC837XERDB_config: unconfig
MVBLM7_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision
-sbc8349_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
+sbc8349_config \
+sbc8349_PCI_33_config \
+sbc8349_PCI_66_config: unconfig
+ @mkdir -p $(obj)include
+ @if [ "$(findstring _PCI_,$@)" ] ; then \
+ $(XECHO) -n "... PCI HOST at " ; \
+ echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
+ fi ; \
+ if [ "$(findstring _33_,$@)" ] ; then \
+ $(XECHO) -n "33MHz... " ; \
+ echo "#define PCI_33M" >>$(obj)include/config.h ; \
+ fi ; \
+ if [ "$(findstring _66_,$@)" ] ; then \
+ $(XECHO) -n "66MHz... " ; \
+ echo "#define PCI_66M" >>$(obj)include/config.h ; \
+ fi ;
+ @$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
SIMPC8313_LP_config \
SIMPC8313_SP_config: unconfig
diff --git a/doc/README.sbc8349 b/doc/README.sbc8349
index 908e7680a6..2c35919f28 100644
--- a/doc/README.sbc8349
+++ b/doc/README.sbc8349
@@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash.
PCI:
====
-This board and U-Boot have been tested with PCI built in, on a SBC8349
-and confirmed that the "pci" command showed the intel e1000 that was
-present in the PCI slot. Note that if a 33MHz 32bit card is inserted
-in the slot, then the whole board will clock down to a 33MHz base
-clock instead of the default 66MHz. This will change the baud clocks
-and mess up your serial console output. If you want to use a 33MHz PCI
-card, then you should build a U-Boot with #undef PCI_66M in the
-include/configs/sbc8349.h and store this to flash prior to powering down
-the board and inserting the 33MHz PCI card.
-
-By default PCI support is disabled to better support very early
-revision MPC834x chips with possible PCI issues. Also PCI support is
-untested on the sbc8347 variants at this point in time.
-
-
- Paul Gortmaker, 01/2007
+There are three configuration choices:
+ sbc8349_config
+ sbc8349_PCI_33_config
+ sbc8349_PCI_66_config
+
+The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
+will be left empty (M66EN high), and so the board will operate with
+a base clock of 66MHz. Note that you need both PCI enabled in u-boot
+and linux in order to have functional PCI under linux. The only
+reason for choosing to not enable PCI would be if you had a very
+early (rev 1.0) CPU with possible PCI issues.
+
+The second enables PCI support and builds for a 33MHz clock rate. Note
+that if a 33MHz 32bit card is inserted in the slot, then the whole board
+will clock down to a 33MHz base clock instead of the default 66MHz. This
+will change the baud clocks and mess up your serial console output if you
+were previously running at 66MHz. If you want to use a 33MHz PCI card,
+then you should build a U-Boot with sbc8349_PCI_33_config and store this
+to flash prior to powering down the board and inserting the 33MHz PCI
+card.
+
+The third option builds PCI support in, and leaves the clocking at the
+default 66MHz. This has been tested with an intel PCI-X e1000 card.
+This is also the appropriate choice for people with a recent (non 1.0)
+CPU who currently have the PCI slot physically empty, but intend to
+possibly add a PCI-X card at a later date.
+
+ => pci
+ Scanning PCI devices on bus 0
+ BusDevFun VendorId DeviceId Device Class Sub-Class
+ _____________________________________________________________
+ 00.00.00 0x1957 0x0080 Processor 0x20
+ 00.11.00 0x8086 0x1026 Network controller 0x00
+ =>
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index d9aa60bcd1..4bf05d2033 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -594,7 +594,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8313erdb.dtb
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
@@ -611,7 +611,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"console=ttyS0\0" \
"setbootargs=setenv bootargs " \
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index d5e62e3472..84cc9fa41e 100644
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -566,7 +566,7 @@
#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -576,7 +576,7 @@
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=mpc8315erdb.dtb\0" \
"usb_phy_type=utmi\0" \
""
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 907965d651..c40d3d3f4a 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -542,7 +542,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc832x_rdb.dtb
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
@@ -558,7 +558,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 4e23a1174a..f16616c0db 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -548,7 +548,7 @@
#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -558,7 +558,7 @@
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=mpc832x_mds.dtb\0" \
""
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 3cf59efa08..1d736f32a6 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -172,7 +172,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
@@ -701,7 +700,7 @@
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -732,7 +731,7 @@
"update=protect off fe000000 fe03ffff; " \
"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0" \
"upd=run load update\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=mpc8349emds.dtb\0" \
""
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index fe6ec48ca4..b072e84473 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -589,7 +589,7 @@
#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -599,7 +599,7 @@
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=mpc836x_mds.dtb\0" \
""
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index a2a2aadb52..a190a50ed8 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -646,7 +646,7 @@ extern int board_pci_host_broken(void);
#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -656,7 +656,7 @@ extern int board_pci_host_broken(void);
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=mpc8379_mds.dtb\0" \
""
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index b637f73959..89fafe7d23 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -190,8 +190,8 @@
/* 0x3937d322 */
#define CONFIG_SYS_DDR_TIMING_2 0x02984cc8
-#define CONFIG_SYS_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (256 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+#define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x06090100 */
#if defined(CONFIG_DDR_2T_TIMING)
@@ -205,7 +205,7 @@
/* 0x43000000 */
#endif
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
+#define CONFIG_SYS_DDR_MODE ((0x0406 << SDRAM_MODE_ESD_SHIFT) \
| (0x0442 << SDRAM_MODE_SD_SHIFT))
/* 0x04400442 */ /* DDR400 */
#define CONFIG_SYS_DDR_MODE2 0x00000000
@@ -668,7 +668,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8379_rdb.dtb
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
@@ -684,7 +684,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 492bdccb5a..da08b7c213 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -250,7 +250,7 @@ extern int tqm834x_num_flash_banks;
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI1 host bridge */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_BASE 0x90000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 868bd54a6a..e961bb3929 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -40,24 +40,28 @@
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */
-#undef CONFIG_PCI
/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
-#define PCI_66M
-#ifdef PCI_66M
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#else
+/*
+ * The default if PCI isn't enabled, or if no PCI clk setting is given
+ * is 66MHz; this is what the board defaults to when the PCI slot is
+ * physically empty. The board will automatically (i.e w/o jumpers)
+ * clock down to 33MHz if you insert a 33MHz PCI card.
+ */
+#ifdef PCI_33M
#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
+#else /* 66M */
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
#endif
#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
-#else
+#ifdef PCI_33M
#define CONFIG_SYS_CLK_FREQ 33000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
+#else /* 66M */
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#endif
#endif
@@ -153,7 +157,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
@@ -627,7 +630,7 @@
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -654,7 +657,7 @@
"update=protect off ff800000 ff83ffff; " \
"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
"upd=run load update\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=sbc8349.dtb\0" \
""
diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index 1477552df4..5304ec94ae 100644
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -152,7 +152,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
-#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
@@ -555,7 +554,7 @@
#define CONFIG_ROOTPATH /tftpboot/rootfs
#define CONFIG_BOOTFILE uImage
-#define CONFIG_LOADADDR 500000 /* def location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* boot command will set bootargs */
@@ -582,7 +581,7 @@
"update=protect off fff00000 fff3ffff; " \
"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
"upd=run load update\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=vme8349.dtb\0" \
""
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index fd742c7809..44115c91b4 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -837,6 +837,9 @@
#define CSCONFIG_EN 0x80000000
#define CSCONFIG_AP 0x00800000
#define CSCONFIG_ODT_WR_ACS 0x00010000
+#if defined(CONFIG_MPC832x)
+#define CSCONFIG_ODT_WR_CFG 0x00040000
+#endif
#define CSCONFIG_BANK_BIT_3 0x00004000
#define CSCONFIG_ROW_BIT 0x00000700
#define CSCONFIG_ROW_BIT_12 0x00000000