diff options
| author | Richard Zhu <r65037@freescale.com> | 2013-04-16 09:45:41 +0800 |
|---|---|---|
| committer | Richard Zhu <r65037@freescale.com> | 2013-04-16 13:49:30 +0800 |
| commit | 75a15f1dc81d03aa90d38edf4b775b8d57166f3f (patch) | |
| tree | 4290a19e6f5639e5d00d4b567aa89cc301ab77f0 | |
| parent | ed9f87cab1b7a4bf0a63c34b73de69994f64a07e (diff) | |
ENGR00254470-3 mx6q-sabreauto:sata device can't work properly on most boards
Revert "ENGR00241595-3 mx6q-sabreauto:Enable SATA PHY PDDQ default"
This reverts commit 027af67a25773a0872659788eab0c09b72e2bbe0.
Reasons:
* according to SATA Power mode (in SATA protocol) PHY TX/RX/CLK is
powered down automatically according to SATA controller
power mode SATA port support Disable/Slumber/Partial/Enabled(OOB)
The SATA PHY PDDQ mode is one-shot and recommeded to be used for test,
SATA would not work properly if the PHY PDDQ mode is enabled in U-boot.
Signed-off-by: Richard Zhu <r65037@freescale.com>
| -rw-r--r-- | board/freescale/mx6q_sabreauto/mx6q_sabreauto.c | 21 |
1 files changed, 0 insertions, 21 deletions
diff --git a/board/freescale/mx6q_sabreauto/mx6q_sabreauto.c b/board/freescale/mx6q_sabreauto/mx6q_sabreauto.c index 0a53dd9e28..00ef2ed17a 100644 --- a/board/freescale/mx6q_sabreauto/mx6q_sabreauto.c +++ b/board/freescale/mx6q_sabreauto/mx6q_sabreauto.c @@ -215,8 +215,6 @@ void board_mmu_init(void) #define ANATOP_PLL_PWDN_MASK 0x00001000 #define ANATOP_PLL_HOLD_RING_OFF_MASK 0x00000800 #define ANATOP_SATA_CLK_ENABLE_MASK 0x00100000 -#define PORT_PHY_CTL 0x178 -#define PORT_PHY_CTL_PDDQ_LOC 0x100000 #ifdef CONFIG_DWC_AHSATA /* Staggered Spin-up */ @@ -231,11 +229,6 @@ int sata_initialize(void) u32 iterations = 1000000; if (sata_curr_device == -1) { - /* Make sure that the PDDQ mode is disabled. */ - reg = readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL); - writel(reg & (~PORT_PHY_CTL_PDDQ_LOC), - SATA_ARB_BASE_ADDR + PORT_PHY_CTL); - /* Reset HBA */ writel(HOST_RESET, SATA_ARB_BASE_ADDR + HOST_CTL); @@ -315,16 +308,6 @@ static int setup_sata(void) * */ reg |= 0x59124c6; writel(reg, IOMUXC_BASE_ADDR + 0x34); - /* FIXME */ - /* - * It needs to wait SATA PHY initialize completed, otherwise write the - * PORT_PHY_CTL will fail, then can't enable PDDQ which let PHY entry LPM - * Currently set it as 1ms. - */ - udelay(1000); - /* Enable PDDQ mode in default */ - writel(readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL) | PORT_PHY_CTL_PDDQ_LOC, - SATA_ARB_BASE_ADDR + PORT_PHY_CTL); return 0; } @@ -1205,10 +1188,6 @@ int checkboard(void) printf("UNKNOWN\n"); break; } - if (cpu_is_mx6q()) - printf("SATA PDDQ: %s\n", ((readl(SATA_ARB_BASE_ADDR - + PORT_PHY_CTL) - & PORT_PHY_CTL_PDDQ_LOC)>>20) ? "enabled" : "disabled"); return 0; } |