tezi-metadata: replace soc overrides to also include use-mainline-bsp

With use-mainline-bsp the SoC overrides mx6/mx6q/mx6ull... are filtered out of
the overrides. Replace them with the specific machine name.

Related-to: ELB-2805
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>

1 files changed, 0 insertions, 79 deletions

diff --git a/recipes-bsp/tezi-metadata/files/mx6/wrapup.sh b/recipes-bsp/tezi-metadata/files/mx6/wrapup.sh
deleted file mode 100644
index bbdda13..0000000
--- a/recipes-bsp/tezi-metadata/files/mx6/wrapup.sh
+++ /dev/null
@@ -1,79 +0,0 @@
-#!/bin/sh
-#
-# (c) Toradex AG 2016-2017
-#
-# Apalis/Colibri iMX6 in-field hardware update script
-#
-# One-time configurations (non-reversible!):
-# - Fuse SoC to use eMMC Fast Boot mode
-# - Enable eMMC H/W reset capabilities
-# Required configurations
-# - Configure Boot Bus mode (due to eMMC Fast Boot mode above)
-#
-# Other configurations
-# - Boot from eMMC boot partition (must run as wrap-up script)
-#
-
-PRODUCT_ID=$1
-BOARD_REV=$2
-SERIAL=$3
-IMAGE_FOLDER=$4
-
-error_exit () {
-	echo "$1" 1>&2
-	exit 1
-}
-
-# Do a basic validation that we do this on one of our modules
-case $PRODUCT_ID in
-0027|0028|0029|0035) ;;
-0014|0015|0016|0017) ;;
-*) error_exit "This script is meant to be run on a Apalis/Colibri iMX6. Aborting...";
-esac
-
-# Fuse SoC's BOOT_CFG to enable eMMC Fast Boot mode, if necessary
-# WARNING: Fusing is a one-time operation, do not change values
-# here unless you are absolutely sure what your are doing.
-BOOT_CFG=0x5072
-if [ ! -f /sys/fsl_otp/HW_OCOTP_CFG4 ]; then
-	echo "Fusing not supported."
-elif grep -q ${BOOT_CFG} /sys/fsl_otp/HW_OCOTP_CFG4; then
-	echo "No new value for BOOT_CFG required."
-else
-	echo ${BOOT_CFG} > /sys/fsl_otp/HW_OCOTP_CFG4
-	if [ "$?" != "0" ]; then
-		error_exit "Writing fuse BOOT_CFG failed! Aborting..."
-	fi
-	echo "Fuse BOOT_CFG updated to ${BOOT_CFG}."
-fi
-
-# eMMC configurations
-MMCDEV=/dev/mmcblk0
-
-# Enable eMMC H/W Reset feature. This need to be executed before the other
-# eMMC settings, it seems that this command resets all settings.
-# Since this is a one-time operation, it will fail the second time. Ignore
-# errors and redirect stderr to stdout.
-mmc hwreset enable ${MMCDEV} 2>&1
-if [ "$?" == "0" ]; then
-	echo "H/W Reset permanently enabled on ${MMCDEV}"
-fi
-
-# Set boot bus mode
-if ! mmc bootbus set single_hs x1 x8 ${MMCDEV}; then
-	error_exit "Setting boot bus mode failed"
-fi
-
-# Enable eMMC boot partition 1 (mmcblkXboot0) and boot ack
-# Make sure everything hit the eMMC when execute this command. Otherwise
-# the eMMC will reset the configuration.
-sync
-if ! mmc bootpart enable 1 1 ${MMCDEV}; then
-	error_exit "Setting bootpart failed"
-fi
-
-mmc extcsd read ${MMCDEV} | grep -e BOOT_BUS_CONDITIONS -e PARTITION_CONFIG -e RST_N_FUNCTION
-
-echo "Apalis/Colibri iMX6 in-field hardware update script ended successfully."
-
-exit 0