summaryrefslogtreecommitdiff
path: root/drivers/cdrom/sonycd535.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/cdrom/sonycd535.c')
-rw-r--r--drivers/cdrom/sonycd535.c1689
1 files changed, 0 insertions, 1689 deletions
diff --git a/drivers/cdrom/sonycd535.c b/drivers/cdrom/sonycd535.c
deleted file mode 100644
index f77ada933ea0..000000000000
--- a/drivers/cdrom/sonycd535.c
+++ /dev/null
@@ -1,1689 +0,0 @@
-/*
- * Sony CDU-535 interface device driver
- *
- * This is a modified version of the CDU-31A device driver (see below).
- * Changes were made using documentation for the CDU-531 (which Sony
- * assures me is very similar to the 535) and partial disassembly of the
- * DOS driver. I used Minyard's driver and replaced the CDU-31A
- * commands with the CDU-531 commands. This was complicated by a different
- * interface protocol with the drive. The driver is still polled.
- *
- * Data transfer rate is about 110 Kb/sec, theoretical maximum is 150 Kb/sec.
- * I tried polling without the sony_sleep during the data transfers but
- * it did not speed things up any.
- *
- * 1993-05-23 (rgj) changed the major number to 21 to get rid of conflict
- * with CDU-31A driver. This is the also the number from the Linux
- * Device Driver Registry for the Sony Drive. Hope nobody else is using it.
- *
- * 1993-08-29 (rgj) remove the configuring of the interface board address
- * from the top level configuration, you have to modify it in this file.
- *
- * 1995-01-26 Made module-capable (Joel Katz <Stimpson@Panix.COM>)
- *
- * 1995-05-20
- * Modified to support CDU-510/515 series
- * (Claudio Porfiri<C.Porfiri@nisms.tei.ericsson.se>)
- * Fixed to report verify_area() failures
- * (Heiko Eissfeldt <heiko@colossus.escape.de>)
- *
- * 1995-06-01
- * More changes to support CDU-510/515 series
- * (Claudio Porfiri<C.Porfiri@nisms.tei.ericsson.se>)
- *
- * November 1999 -- Make kernel-parameter implementation work with 2.3.x
- * Removed init_module & cleanup_module in favor of
- * module_init & module_exit.
- * Torben Mathiasen <tmm@image.dk>
- *
- * September 2003 - Fix SMP support by removing cli/sti calls.
- * Using spinlocks with a wait_queue instead.
- * Felipe Damasio <felipewd@terra.com.br>
- *
- * Things to do:
- * - handle errors and status better, put everything into a single word
- * - use interrupts (code mostly there, but a big hole still missing)
- * - handle multi-session CDs?
- * - use DMA?
- *
- * Known Bugs:
- * -
- *
- * Ken Pizzini (ken@halcyon.com)
- *
- * Original by:
- * Ron Jeppesen (ronj.an@site007.saic.com)
- *
- *
- *------------------------------------------------------------------------
- * Sony CDROM interface device driver.
- *
- * Corey Minyard (minyard@wf-rch.cirr.com) (CDU-535 complaints to Ken above)
- *
- * Colossians 3:17
- *
- * The Sony interface device driver handles Sony interface CDROM
- * drives and provides a complete block-level interface as well as an
- * ioctl() interface compatible with the Sun (as specified in
- * include/linux/cdrom.h). With this interface, CDROMs can be
- * accessed and standard audio CDs can be played back normally.
- *
- * This interface is (unfortunately) a polled interface. This is
- * because most Sony interfaces are set up with DMA and interrupts
- * disables. Some (like mine) do not even have the capability to
- * handle interrupts or DMA. For this reason you will see a bit of
- * the following:
- *
- * snap = jiffies;
- * while (jiffies-snap < SONY_JIFFIES_TIMEOUT)
- * {
- * if (some_condition())
- * break;
- * sony_sleep();
- * }
- * if (some_condition not met)
- * {
- * return an_error;
- * }
- *
- * This ugly hack waits for something to happen, sleeping a little
- * between every try. (The conditional is written so that jiffies
- * wrap-around is handled properly.)
- *
- * One thing about these drives: They talk in MSF (Minute Second Frame) format.
- * There are 75 frames a second, 60 seconds a minute, and up to 75 minutes on a
- * disk. The funny thing is that these are sent to the drive in BCD, but the
- * interface wants to see them in decimal. A lot of conversion goes on.
- *
- * Copyright (C) 1993 Corey Minyard
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-
-
-# include <linux/module.h>
-
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/timer.h>
-#include <linux/fs.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/hdreg.h>
-#include <linux/genhd.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-
-#define REALLY_SLOW_IO
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-
-#include <linux/cdrom.h>
-
-#define MAJOR_NR CDU535_CDROM_MAJOR
-#include <linux/blkdev.h>
-
-#define sony535_cd_base_io sonycd535 /* for compatible parameter passing with "insmod" */
-#include "sonycd535.h"
-
-/*
- * this is the base address of the interface card for the Sony CDU-535
- * CDROM drive. If your jumpers are set for an address other than
- * this one (the default), change the following line to the
- * proper address.
- */
-#ifndef CDU535_ADDRESS
-# define CDU535_ADDRESS 0x340
-#endif
-#ifndef CDU535_INTERRUPT
-# define CDU535_INTERRUPT 0
-#endif
-#ifndef CDU535_HANDLE
-# define CDU535_HANDLE "cdu535"
-#endif
-#ifndef CDU535_MESSAGE_NAME
-# define CDU535_MESSAGE_NAME "Sony CDU-535"
-#endif
-
-#define CDU535_BLOCK_SIZE 2048
-
-#ifndef MAX_SPINUP_RETRY
-# define MAX_SPINUP_RETRY 3 /* 1 is sufficient for most drives... */
-#endif
-#ifndef RETRY_FOR_BAD_STATUS
-# define RETRY_FOR_BAD_STATUS 100 /* in 10th of second */
-#endif
-
-#ifndef DEBUG
-# define DEBUG 1
-#endif
-
-/*
- * SONY535_BUFFER_SIZE determines the size of internal buffer used
- * by the drive. It must be at least 2K and the larger the buffer
- * the better the transfer rate. It does however take system memory.
- * On my system I get the following transfer rates using dd to read
- * 10 Mb off /dev/cdrom.
- *
- * 8K buffer 43 Kb/sec
- * 16K buffer 66 Kb/sec
- * 32K buffer 91 Kb/sec
- * 64K buffer 111 Kb/sec
- * 128K buffer 123 Kb/sec
- * 512K buffer 123 Kb/sec
- */
-#define SONY535_BUFFER_SIZE (64*1024)
-
-/*
- * if LOCK_DOORS is defined then the eject button is disabled while
- * the device is open.
- */
-#ifndef NO_LOCK_DOORS
-# define LOCK_DOORS
-#endif
-
-static int read_subcode(void);
-static void sony_get_toc(void);
-static int cdu_open(struct inode *inode, struct file *filp);
-static inline unsigned int int_to_bcd(unsigned int val);
-static unsigned int bcd_to_int(unsigned int bcd);
-static int do_sony_cmd(Byte * cmd, int nCmd, Byte status[2],
- Byte * response, int n_response, int ignoreStatusBit7);
-
-/* The base I/O address of the Sony Interface. This is a variable (not a
- #define) so it can be easily changed via some future ioctl() */
-static unsigned int sony535_cd_base_io = CDU535_ADDRESS;
-module_param(sony535_cd_base_io, int, 0);
-
-/*
- * The following are I/O addresses of the various registers for the drive. The
- * comment for the base address also applies here.
- */
-static unsigned short select_unit_reg;
-static unsigned short result_reg;
-static unsigned short command_reg;
-static unsigned short read_status_reg;
-static unsigned short data_reg;
-
-static DEFINE_SPINLOCK(sonycd535_lock); /* queue lock */
-static struct request_queue *sonycd535_queue;
-
-static int initialized; /* Has the drive been initialized? */
-static int sony_disc_changed = 1; /* Has the disk been changed
- since the last check? */
-static int sony_toc_read; /* Has the table of contents been
- read? */
-static unsigned int sony_buffer_size; /* Size in bytes of the read-ahead
- buffer. */
-static unsigned int sony_buffer_sectors; /* Size (in 2048 byte records) of
- the read-ahead buffer. */
-static unsigned int sony_usage; /* How many processes have the
- drive open. */
-
-static int sony_first_block = -1; /* First OS block (512 byte) in
- the read-ahead buffer */
-static int sony_last_block = -1; /* Last OS block (512 byte) in
- the read-ahead buffer */
-
-static struct s535_sony_toc *sony_toc; /* Points to the table of
- contents. */
-
-static struct s535_sony_subcode *last_sony_subcode; /* Points to the last
- subcode address read */
-static Byte **sony_buffer; /* Points to the pointers
- to the sector buffers */
-
-static int sony_inuse; /* is the drive in use? Only one
- open at a time allowed */
-
-/*
- * The audio status uses the values from read subchannel data as specified
- * in include/linux/cdrom.h.
- */
-static int sony_audio_status = CDROM_AUDIO_NO_STATUS;
-
-/*
- * The following are a hack for pausing and resuming audio play. The drive
- * does not work as I would expect it, if you stop it then start it again,
- * the drive seeks back to the beginning and starts over. This holds the
- * position during a pause so a resume can restart it. It uses the
- * audio status variable above to tell if it is paused.
- * I just kept the CDU-31A driver behavior rather than using the PAUSE
- * command on the CDU-535.
- */
-static Byte cur_pos_msf[3];
-static Byte final_pos_msf[3];
-
-/* What IRQ is the drive using? 0 if none. */
-static int sony535_irq_used = CDU535_INTERRUPT;
-
-/* The interrupt handler will wake this queue up when it gets an interrupt. */
-static DECLARE_WAIT_QUEUE_HEAD(cdu535_irq_wait);
-
-
-/*
- * This routine returns 1 if the disk has been changed since the last
- * check or 0 if it hasn't. Setting flag to 0 resets the changed flag.
- */
-static int
-cdu535_check_media_change(struct gendisk *disk)
-{
- /* if driver is not initialized, always return 0 */
- int retval = initialized ? sony_disc_changed : 0;
- sony_disc_changed = 0;
- return retval;
-}
-
-static inline void
-enable_interrupts(void)
-{
-#ifdef USE_IRQ
- /*
- * This code was taken from cdu31a.c; it will not
- * directly work for the cdu535 as written...
- */
- curr_control_reg |= ( SONY_ATTN_INT_EN_BIT
- | SONY_RES_RDY_INT_EN_BIT
- | SONY_DATA_RDY_INT_EN_BIT);
- outb(curr_control_reg, sony_cd_control_reg);
-#endif
-}
-
-static inline void
-disable_interrupts(void)
-{
-#ifdef USE_IRQ
- /*
- * This code was taken from cdu31a.c; it will not
- * directly work for the cdu535 as written...
- */
- curr_control_reg &= ~(SONY_ATTN_INT_EN_BIT
- | SONY_RES_RDY_INT_EN_BIT
- | SONY_DATA_RDY_INT_EN_BIT);
- outb(curr_control_reg, sony_cd_control_reg);
-#endif
-}
-
-static irqreturn_t
-cdu535_interrupt(int irq, void *dev_id)
-{
- disable_interrupts();
- if (waitqueue_active(&cdu535_irq_wait)) {
- wake_up(&cdu535_irq_wait);
- return IRQ_HANDLED;
- }
- printk(CDU535_MESSAGE_NAME
- ": Got an interrupt but nothing was waiting\n");
- return IRQ_NONE;
-}
-
-
-/*
- * Wait a little while.
- */
-static inline void
-sony_sleep(void)
-{
- if (sony535_irq_used <= 0) { /* poll */
- yield();
- } else { /* Interrupt driven */
- DEFINE_WAIT(wait);
-
- spin_lock_irq(&sonycd535_lock);
- enable_interrupts();
- prepare_to_wait(&cdu535_irq_wait, &wait, TASK_INTERRUPTIBLE);
- spin_unlock_irq(&sonycd535_lock);
- schedule();
- finish_wait(&cdu535_irq_wait, &wait);
- }
-}
-
-/*------------------start of SONY CDU535 very specific ---------------------*/
-
-/****************************************************************************
- * void select_unit( int unit_no )
- *
- * Select the specified unit (0-3) so that subsequent commands reference it
- ****************************************************************************/
-static void
-select_unit(int unit_no)
-{
- unsigned int select_mask = ~(1 << unit_no);
- outb(select_mask, select_unit_reg);
-}
-
-/***************************************************************************
- * int read_result_reg( Byte *data_ptr )
- *
- * Read a result byte from the Sony CDU controller, store in location pointed
- * to by data_ptr. Return zero on success, TIME_OUT if we did not receive
- * data.
- ***************************************************************************/
-static int
-read_result_reg(Byte *data_ptr)
-{
- unsigned long snap;
- int read_status;
-
- snap = jiffies;
- while (jiffies-snap < SONY_JIFFIES_TIMEOUT) {
- read_status = inb(read_status_reg);
- if ((read_status & SONY535_RESULT_NOT_READY_BIT) == 0) {
-#if DEBUG > 1
- printk(CDU535_MESSAGE_NAME
- ": read_result_reg(): readStatReg = 0x%x\n", read_status);
-#endif
- *data_ptr = inb(result_reg);
- return 0;
- } else {
- sony_sleep();
- }
- }
- printk(CDU535_MESSAGE_NAME " read_result_reg: TIME OUT!\n");
- return TIME_OUT;
-}
-
-/****************************************************************************
- * int read_exec_status( Byte status[2] )
- *
- * Read the execution status of the last command and put into status.
- * Handles reading second status word if available. Returns 0 on success,
- * TIME_OUT on failure.
- ****************************************************************************/
-static int
-read_exec_status(Byte status[2])
-{
- status[1] = 0;
- if (read_result_reg(&(status[0])) != 0)
- return TIME_OUT;
- if ((status[0] & 0x80) != 0) { /* byte two follows */
- if (read_result_reg(&(status[1])) != 0)
- return TIME_OUT;
- }
-#if DEBUG > 1
- printk(CDU535_MESSAGE_NAME ": read_exec_status: read 0x%x 0x%x\n",
- status[0], status[1]);
-#endif
- return 0;
-}
-
-/****************************************************************************
- * int check_drive_status( void )
- *
- * Check the current drive status. Using this before executing a command
- * takes care of the problem of unsolicited drive status-2 messages.
- * Add a check of the audio status if we think the disk is playing.
- ****************************************************************************/
-static int
-check_drive_status(void)
-{
- Byte status, e_status[2];
- int CDD, ATN;
- Byte cmd;
-
- select_unit(0);
- if (sony_audio_status == CDROM_AUDIO_PLAY) { /* check status */
- outb(SONY535_REQUEST_AUDIO_STATUS, command_reg);
- if (read_result_reg(&status) == 0) {
- switch (status) {
- case 0x0:
- break; /* play in progress */
- case 0x1:
- break; /* paused */
- case 0x3: /* audio play completed */
- case 0x5: /* play not requested */
- sony_audio_status = CDROM_AUDIO_COMPLETED;
- read_subcode();
- break;
- case 0x4: /* error during play */
- sony_audio_status = CDROM_AUDIO_ERROR;
- break;
- }
- }
- }
- /* now check drive status */
- outb(SONY535_REQUEST_DRIVE_STATUS_2, command_reg);
- if (read_result_reg(&status) != 0)
- return TIME_OUT;
-
-#if DEBUG > 1
- printk(CDU535_MESSAGE_NAME ": check_drive_status() got 0x%x\n", status);
-#endif
-
- if (status == 0)
- return 0;
-
- ATN = status & 0xf;
- CDD = (status >> 4) & 0xf;
-
- switch (ATN) {
- case 0x0:
- break; /* go on to CDD stuff */
- case SONY535_ATN_BUSY:
- if (initialized)
- printk(CDU535_MESSAGE_NAME " error: drive busy\n");
- return CD_BUSY;
- case SONY535_ATN_EJECT_IN_PROGRESS:
- printk(CDU535_MESSAGE_NAME " error: eject in progress\n");
- sony_audio_status = CDROM_AUDIO_INVALID;
- return CD_BUSY;
- case SONY535_ATN_RESET_OCCURRED:
- case SONY535_ATN_DISC_CHANGED:
- case SONY535_ATN_RESET_AND_DISC_CHANGED:
-#if DEBUG > 0
- printk(CDU535_MESSAGE_NAME " notice: reset occurred or disc changed\n");
-#endif
- sony_disc_changed = 1;
- sony_toc_read = 0;
- sony_audio_status = CDROM_AUDIO_NO_STATUS;
- sony_first_block = -1;
- sony_last_block = -1;
- if (initialized) {
- cmd = SONY535_SPIN_UP;
- do_sony_cmd(&cmd, 1, e_status, NULL, 0, 0);
- sony_get_toc();
- }
- return 0;
- default:
- printk(CDU535_MESSAGE_NAME " error: drive busy (ATN=0x%x)\n", ATN);
- return CD_BUSY;
- }
- switch (CDD) { /* the 531 docs are not helpful in decoding this */
- case 0x0: /* just use the values from the DOS driver */
- case 0x2:
- case 0xa:
- break; /* no error */
- case 0xc:
- printk(CDU535_MESSAGE_NAME
- ": check_drive_status(): CDD = 0xc! Not properly handled!\n");
- return CD_BUSY; /* ? */
- default:
- return CD_BUSY;
- }
- return 0;
-} /* check_drive_status() */
-
-/*****************************************************************************
- * int do_sony_cmd( Byte *cmd, int n_cmd, Byte status[2],
- * Byte *response, int n_response, int ignore_status_bit7 )
- *
- * Generic routine for executing commands. The command and its parameters
- * should be placed in the cmd[] array, number of bytes in the command is
- * stored in nCmd. The response from the command will be stored in the
- * response array. The number of bytes you expect back (excluding status)
- * should be passed in n_response. Finally, some
- * commands set bit 7 of the return status even when there is no second
- * status byte, on these commands set ignoreStatusBit7 TRUE.
- * If the command was sent and data received back, then we return 0,
- * else we return TIME_OUT. You still have to check the status yourself.
- * You should call check_drive_status() before calling this routine
- * so that you do not lose notifications of disk changes, etc.
- ****************************************************************************/
-static int
-do_sony_cmd(Byte * cmd, int n_cmd, Byte status[2],
- Byte * response, int n_response, int ignore_status_bit7)
-{
- int i;
-
- /* write out the command */
- for (i = 0; i < n_cmd; i++)
- outb(cmd[i], command_reg);
-
- /* read back the status */
- if (read_result_reg(status) != 0)
- return TIME_OUT;
- if (!ignore_status_bit7 && ((status[0] & 0x80) != 0)) {
- /* get second status byte */
- if (read_result_reg(status + 1) != 0)
- return TIME_OUT;
- } else {
- status[1] = 0;
- }
-#if DEBUG > 2
- printk(CDU535_MESSAGE_NAME ": do_sony_cmd %x: %x %x\n",
- *cmd, status[0], status[1]);
-#endif
-
- /* do not know about when I should read set of data and when not to */
- if ((status[0] & ((ignore_status_bit7 ? 0x7f : 0xff) & 0x8f)) != 0)
- return 0;
-
- /* else, read in rest of data */
- for (i = 0; 0 < n_response; n_response--, i++)
- if (read_result_reg(response + i) != 0)
- return TIME_OUT;
- return 0;
-} /* do_sony_cmd() */
-
-/**************************************************************************
- * int set_drive_mode( int mode, Byte status[2] )
- *
- * Set the drive mode to the specified value (mode=0 is audio, mode=e0
- * is mode-1 CDROM
- **************************************************************************/
-static int
-set_drive_mode(int mode, Byte status[2])
-{
- Byte cmd_buff[2];
- Byte ret_buff[1];
-
- cmd_buff[0] = SONY535_SET_DRIVE_MODE;
- cmd_buff[1] = mode;
- return do_sony_cmd(cmd_buff, 2, status, ret_buff, 1, 1);
-}
-
-/***************************************************************************
- * int seek_and_read_N_blocks( Byte params[], int n_blocks, Byte status[2],
- * Byte *data_buff, int buff_size )
- *
- * Read n_blocks of data from the CDROM starting at position params[0:2],
- * number of blocks in stored in params[3:5] -- both these are already
- * int bcd format.
- * Transfer the data into the buffer pointed at by data_buff. buff_size
- * gives the number of bytes available in the buffer.
- * The routine returns number of bytes read in if successful, otherwise
- * it returns one of the standard error returns.
- ***************************************************************************/
-static int
-seek_and_read_N_blocks(Byte params[], int n_blocks, Byte status[2],
- Byte **buff, int buf_size)
-{
- Byte cmd_buff[7];
- int i;
- int read_status;
- unsigned long snap;
- Byte *data_buff;
- int sector_count = 0;
-
- if (buf_size < CDU535_BLOCK_SIZE * n_blocks)
- return NO_ROOM;
-
- set_drive_mode(SONY535_CDROM_DRIVE_MODE, status);
-
- /* send command to read the data */
- cmd_buff[0] = SONY535_SEEK_AND_READ_N_BLOCKS_1;
- for (i = 0; i < 6; i++)
- cmd_buff[i + 1] = params[i];
- for (i = 0; i < 7; i++)
- outb(cmd_buff[i], command_reg);
-
- /* read back the data one block at a time */
- while (0 < n_blocks--) {
- /* wait for data to be ready */
- int data_valid = 0;
- snap = jiffies;
- while (jiffies-snap < SONY_JIFFIES_TIMEOUT) {
- read_status = inb(read_status_reg);
- if ((read_status & SONY535_RESULT_NOT_READY_BIT) == 0) {
- read_exec_status(status);
- return BAD_STATUS;
- }
- if ((read_status & SONY535_DATA_NOT_READY_BIT) == 0) {
- /* data is ready, read it */
- data_buff = buff[sector_count++];
- for (i = 0; i < CDU535_BLOCK_SIZE; i++)
- *data_buff++ = inb(data_reg); /* unrolling this loop does not seem to help */
- data_valid = 1;
- break; /* exit the timeout loop */
- }
- sony_sleep(); /* data not ready, sleep a while */
- }
- if (!data_valid)
- return TIME_OUT; /* if we reach this stage */
- }
-
- /* read all the data, now read the status */
- if ((i = read_exec_status(status)) != 0)
- return i;
- return CDU535_BLOCK_SIZE * sector_count;
-} /* seek_and_read_N_blocks() */
-
-/****************************************************************************
- * int request_toc_data( Byte status[2], struct s535_sony_toc *toc )
- *
- * Read in the table of contents data. Converts all the bcd data
- * into integers in the toc structure.
- ****************************************************************************/
-static int
-request_toc_data(Byte status[2], struct s535_sony_toc *toc)
-{
- int to_status;
- int i, j, n_tracks, track_no;
- int first_track_num, last_track_num;
- Byte cmd_no = 0xb2;
- Byte track_address_buffer[5];
-
- /* read the fixed portion of the table of contents */
- if ((to_status = do_sony_cmd(&cmd_no, 1, status, (Byte *) toc, 15, 1)) != 0)
- return to_status;
-
- /* convert the data into integers so we can use them */
- first_track_num = bcd_to_int(toc->first_track_num);
- last_track_num = bcd_to_int(toc->last_track_num);
- n_tracks = last_track_num - first_track_num + 1;
-
- /* read each of the track address descriptors */
- for (i = 0; i < n_tracks; i++) {
- /* read the descriptor into a temporary buffer */
- for (j = 0; j < 5; j++) {
- if (read_result_reg(track_address_buffer + j) != 0)
- return TIME_OUT;
- if (j == 1) /* need to convert from bcd */
- track_no = bcd_to_int(track_address_buffer[j]);
- }
- /* copy the descriptor to proper location - sonycd.c just fills */
- memcpy(toc->tracks + i, track_address_buffer, 5);
- }
- return 0;
-} /* request_toc_data() */
-
-/***************************************************************************
- * int spin_up_drive( Byte status[2] )
- *
- * Spin up the drive (unless it is already spinning).
- ***************************************************************************/
-static int
-spin_up_drive(Byte status[2])
-{
- Byte cmd;
-
- /* first see if the drive is already spinning */
- cmd = SONY535_REQUEST_DRIVE_STATUS_1;
- if (do_sony_cmd(&cmd, 1, status, NULL, 0, 0) != 0)
- return TIME_OUT;
- if ((status[0] & SONY535_STATUS1_NOT_SPINNING) == 0)
- return 0; /* it's already spinning */
-
- /* otherwise, give the spin-up command */
- cmd = SONY535_SPIN_UP;
- return do_sony_cmd(&cmd, 1, status, NULL, 0, 0);
-}
-
-/*--------------------end of SONY CDU535 very specific ---------------------*/
-
-/* Convert from an integer 0-99 to BCD */
-static inline unsigned int
-int_to_bcd(unsigned int val)
-{
- int retval;
-
- retval = (val / 10) << 4;
- retval = retval | val % 10;
- return retval;
-}
-
-
-/* Convert from BCD to an integer from 0-99 */
-static unsigned int
-bcd_to_int(unsigned int bcd)
-{
- return (((bcd >> 4) & 0x0f) * 10) + (bcd & 0x0f);
-}
-
-
-/*
- * Convert a logical sector value (like the OS would want to use for
- * a block device) to an MSF format.
- */
-static void
-log_to_msf(unsigned int log, Byte *msf)
-{
- log = log + LOG_START_OFFSET;
- msf[0] = int_to_bcd(log / 4500);
- log = log % 4500;
- msf[1] = int_to_bcd(log / 75);
- msf[2] = int_to_bcd(log % 75);
-}
-
-
-/*
- * Convert an MSF format to a logical sector.
- */
-static unsigned int
-msf_to_log(Byte *msf)
-{
- unsigned int log;
-
-
- log = bcd_to_int(msf[2]);
- log += bcd_to_int(msf[1]) * 75;
- log += bcd_to_int(msf[0]) * 4500;
- log = log - LOG_START_OFFSET;
-
- return log;
-}
-
-
-/*
- * Take in integer size value and put it into a buffer like
- * the drive would want to see a number-of-sector value.
- */
-static void
-size_to_buf(unsigned int size, Byte *buf)
-{
- buf[0] = size / 65536;
- size = size % 65536;
- buf[1] = size / 256;
- buf[2] = size % 256;
-}
-
-
-/*
- * The OS calls this to perform a read or write operation to the drive.
- * Write obviously fail. Reads to a read ahead of sony_buffer_size
- * bytes to help speed operations. This especially helps since the OS
- * may use 1024 byte blocks and the drive uses 2048 byte blocks. Since most
- * data access on a CD is done sequentially, this saves a lot of operations.
- */
-static void
-do_cdu535_request(request_queue_t * q)
-{
- struct request *req;
- unsigned int read_size;
- int block;
- int nsect;
- int copyoff;
- int spin_up_retry;
- Byte params[10];
- Byte status[2];
- Byte cmd[2];
-
- while (1) {
- req = elv_next_request(q);
- if (!req)
- return;
-
- block = req->sector;
- nsect = req->nr_sectors;
- if (!blk_fs_request(req)) {
- end_request(req, 0);
- continue;
- }
- if (rq_data_dir(req) == WRITE) {
- end_request(req, 0);
- continue;
- }
- /*
- * If the block address is invalid or the request goes beyond
- * the end of the media, return an error.
- */
- if (sony_toc->lead_out_start_lba <= (block/4)) {
- end_request(req, 0);
- return;
- }
- if (sony_toc->lead_out_start_lba <= ((block + nsect) / 4)) {
- end_request(req, 0);
- return;
- }
- while (0 < nsect) {
- /*
- * If the requested sector is not currently in
- * the read-ahead buffer, it must be read in.
- */
- if ((block < sony_first_block) || (sony_last_block < block)) {
- sony_first_block = (block / 4) * 4;
- log_to_msf(block / 4, params);
-
- /*
- * If the full read-ahead would go beyond the end of the media, trim
- * it back to read just till the end of the media.
- */
- if (sony_toc->lead_out_start_lba <= ((block / 4) + sony_buffer_sectors)) {
- sony_last_block = (sony_toc->lead_out_start_lba * 4) - 1;
- read_size = sony_toc->lead_out_start_lba - (block / 4);
- } else {
- sony_last_block = sony_first_block + (sony_buffer_sectors * 4) - 1;
- read_size = sony_buffer_sectors;
- }
- size_to_buf(read_size, &params[3]);
-
- /*
- * Read the data. If the drive was not spinning,
- * spin it up and try some more.
- */
- for (spin_up_retry=0 ;; ++spin_up_retry) {
- /* This loop has been modified to support the Sony
- * CDU-510/515 series, thanks to Claudio Porfiri
- * <C.Porfiri@nisms.tei.ericsson.se>.
- */
- /*
- * This part is to deal with very slow hardware. We
- * try at most MAX_SPINUP_RETRY times to read the same
- * block. A check for seek_and_read_N_blocks' result is
- * performed; if the result is wrong, the CDROM's engine
- * is restarted and the operation is tried again.
- */
- /*
- * 1995-06-01: The system got problems when downloading
- * from Slackware CDROM, the problem seems to be:
- * seek_and_read_N_blocks returns BAD_STATUS and we
- * should wait for a while before retrying, so a new
- * part was added to discriminate the return value from
- * seek_and_read_N_blocks for the various cases.
- */
- int readStatus = seek_and_read_N_blocks(params, read_size,
- status, sony_buffer, (read_size * CDU535_BLOCK_SIZE));
- if (0 <= readStatus) /* Good data; common case, placed first */
- break;
- if (readStatus == NO_ROOM || spin_up_retry == MAX_SPINUP_RETRY) {
- /* give up */
- if (readStatus == NO_ROOM)
- printk(CDU535_MESSAGE_NAME " No room to read from CD\n");
- else
- printk(CDU535_MESSAGE_NAME " Read error: 0x%.2x\n",
- status[0]);
- sony_first_block = -1;
- sony_last_block = -1;
- end_request(req, 0);
- return;
- }
- if (readStatus == BAD_STATUS) {
- /* Sleep for a while, then retry */
- set_current_state(TASK_INTERRUPTIBLE);
- spin_unlock_irq(&sonycd535_lock);
- schedule_timeout(RETRY_FOR_BAD_STATUS*HZ/10);
- spin_lock_irq(&sonycd535_lock);
- }
-#if DEBUG > 0
- printk(CDU535_MESSAGE_NAME
- " debug: calling spin up when reading data!\n");
-#endif
- cmd[0] = SONY535_SPIN_UP;
- do_sony_cmd(cmd, 1, status, NULL, 0, 0);
- }
- }
- /*
- * The data is in memory now, copy it to the buffer and advance to the
- * next block to read.
- */
- copyoff = block - sony_first_block;
- memcpy(req->buffer,
- sony_buffer[copyoff / 4] + 512 * (copyoff % 4), 512);
-
- block += 1;
- nsect -= 1;
- req->buffer += 512;
- }
-
- end_request(req, 1);
- }
-}
-
-/*
- * Read the table of contents from the drive and set sony_toc_read if
- * successful.
- */
-static void
-sony_get_toc(void)
-{
- Byte status[2];
- if (!sony_toc_read) {
- /* do not call check_drive_status() from here since it can call this routine */
- if (request_toc_data(status, sony_toc) < 0)
- return;
- sony_toc->lead_out_start_lba = msf_to_log(sony_toc->lead_out_start_msf);
- sony_toc_read = 1;
- }
-}
-
-
-/*
- * Search for a specific track in the table of contents. track is
- * passed in bcd format
- */
-static int
-find_track(int track)
-{
- int i;
- int num_tracks;
-
-
- num_tracks = bcd_to_int(sony_toc->last_track_num) -
- bcd_to_int(sony_toc->first_track_num) + 1;
- for (i = 0; i < num_tracks; i++) {
- if (sony_toc->tracks[i].track == track) {
- return i;
- }
- }
-
- return -1;
-}
-
-/*
- * Read the subcode and put it int last_sony_subcode for future use.
- */
-static int
-read_subcode(void)
-{
- Byte cmd = SONY535_REQUEST_SUB_Q_DATA;
- Byte status[2];
- int dsc_status;
-
- if (check_drive_status() != 0)
- return -EIO;
-
- if ((dsc_status = do_sony_cmd(&cmd, 1, status, (Byte *) last_sony_subcode,
- sizeof(struct s535_sony_subcode), 1)) != 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x, %d (read_subcode)\n",
- status[0], dsc_status);
- return -EIO;
- }
- return 0;
-}
-
-
-/*
- * Get the subchannel info like the CDROMSUBCHNL command wants to see it. If
- * the drive is playing, the subchannel needs to be read (since it would be
- * changing). If the drive is paused or completed, the subcode information has
- * already been stored, just use that. The ioctl call wants things in decimal
- * (not BCD), so all the conversions are done.
- */
-static int
-sony_get_subchnl_info(void __user *arg)
-{
- struct cdrom_subchnl schi;
-
- /* Get attention stuff */
- if (check_drive_status() != 0)
- return -EIO;
-
- sony_get_toc();
- if (!sony_toc_read) {
- return -EIO;
- }
- if (copy_from_user(&schi, arg, sizeof schi))
- return -EFAULT;
-
- switch (sony_audio_status) {
- case CDROM_AUDIO_PLAY:
- if (read_subcode() < 0) {
- return -EIO;
- }
- break;
-
- case CDROM_AUDIO_PAUSED:
- case CDROM_AUDIO_COMPLETED:
- break;
-
- case CDROM_AUDIO_NO_STATUS:
- schi.cdsc_audiostatus = sony_audio_status;
- if (copy_to_user(arg, &schi, sizeof schi))
- return -EFAULT;
- return 0;
- break;
-
- case CDROM_AUDIO_INVALID:
- case CDROM_AUDIO_ERROR:
- default:
- return -EIO;
- }
-
- schi.cdsc_audiostatus = sony_audio_status;
- schi.cdsc_adr = last_sony_subcode->address;
- schi.cdsc_ctrl = last_sony_subcode->control;
- schi.cdsc_trk = bcd_to_int(last_sony_subcode->track_num);
- schi.cdsc_ind = bcd_to_int(last_sony_subcode->index_num);
- if (schi.cdsc_format == CDROM_MSF) {
- schi.cdsc_absaddr.msf.minute = bcd_to_int(last_sony_subcode->abs_msf[0]);
- schi.cdsc_absaddr.msf.second = bcd_to_int(last_sony_subcode->abs_msf[1]);
- schi.cdsc_absaddr.msf.frame = bcd_to_int(last_sony_subcode->abs_msf[2]);
-
- schi.cdsc_reladdr.msf.minute = bcd_to_int(last_sony_subcode->rel_msf[0]);
- schi.cdsc_reladdr.msf.second = bcd_to_int(last_sony_subcode->rel_msf[1]);
- schi.cdsc_reladdr.msf.frame = bcd_to_int(last_sony_subcode->rel_msf[2]);
- } else if (schi.cdsc_format == CDROM_LBA) {
- schi.cdsc_absaddr.lba = msf_to_log(last_sony_subcode->abs_msf);
- schi.cdsc_reladdr.lba = msf_to_log(last_sony_subcode->rel_msf);
- }
- return copy_to_user(arg, &schi, sizeof schi) ? -EFAULT : 0;
-}
-
-
-/*
- * The big ugly ioctl handler.
- */
-static int
-cdu_ioctl(struct inode *inode,
- struct file *file,
- unsigned int cmd,
- unsigned long arg)
-{
- Byte status[2];
- Byte cmd_buff[10], params[10];
- int i;
- int dsc_status;
- void __user *argp = (void __user *)arg;
-
- if (check_drive_status() != 0)
- return -EIO;
-
- switch (cmd) {
- case CDROMSTART: /* Spin up the drive */
- if (spin_up_drive(status) < 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMSTART)\n",
- status[0]);
- return -EIO;
- }
- return 0;
- break;
-
- case CDROMSTOP: /* Spin down the drive */
- cmd_buff[0] = SONY535_HOLD;
- do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
-
- /*
- * Spin the drive down, ignoring the error if the disk was
- * already not spinning.
- */
- sony_audio_status = CDROM_AUDIO_NO_STATUS;
- cmd_buff[0] = SONY535_SPIN_DOWN;
- dsc_status = do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
- if (((dsc_status < 0) && (dsc_status != BAD_STATUS)) ||
- ((status[0] & ~(SONY535_STATUS1_NOT_SPINNING)) != 0)) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMSTOP)\n",
- status[0]);
- return -EIO;
- }
- return 0;
- break;
-
- case CDROMPAUSE: /* Pause the drive */
- cmd_buff[0] = SONY535_HOLD; /* CDU-31 driver uses AUDIO_STOP, not pause */
- if (do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0) != 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMPAUSE)\n",
- status[0]);
- return -EIO;
- }
- /* Get the current position and save it for resuming */
- if (read_subcode() < 0) {
- return -EIO;
- }
- cur_pos_msf[0] = last_sony_subcode->abs_msf[0];
- cur_pos_msf[1] = last_sony_subcode->abs_msf[1];
- cur_pos_msf[2] = last_sony_subcode->abs_msf[2];
- sony_audio_status = CDROM_AUDIO_PAUSED;
- return 0;
- break;
-
- case CDROMRESUME: /* Start the drive after being paused */
- set_drive_mode(SONY535_AUDIO_DRIVE_MODE, status);
-
- if (sony_audio_status != CDROM_AUDIO_PAUSED) {
- return -EINVAL;
- }
- spin_up_drive(status);
-
- /* Start the drive at the saved position. */
- cmd_buff[0] = SONY535_PLAY_AUDIO;
- cmd_buff[1] = 0; /* play back starting at this address */
- cmd_buff[2] = cur_pos_msf[0];
- cmd_buff[3] = cur_pos_msf[1];
- cmd_buff[4] = cur_pos_msf[2];
- cmd_buff[5] = SONY535_PLAY_AUDIO;
- cmd_buff[6] = 2; /* set ending address */
- cmd_buff[7] = final_pos_msf[0];
- cmd_buff[8] = final_pos_msf[1];
- cmd_buff[9] = final_pos_msf[2];
- if ((do_sony_cmd(cmd_buff, 5, status, NULL, 0, 0) != 0) ||
- (do_sony_cmd(cmd_buff + 5, 5, status, NULL, 0, 0) != 0)) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMRESUME)\n",
- status[0]);
- return -EIO;
- }
- sony_audio_status = CDROM_AUDIO_PLAY;
- return 0;
- break;
-
- case CDROMPLAYMSF: /* Play starting at the given MSF address. */
- if (copy_from_user(params, argp, 6))
- return -EFAULT;
- spin_up_drive(status);
- set_drive_mode(SONY535_AUDIO_DRIVE_MODE, status);
-
- /* The parameters are given in int, must be converted */
- for (i = 0; i < 3; i++) {
- cmd_buff[2 + i] = int_to_bcd(params[i]);
- cmd_buff[7 + i] = int_to_bcd(params[i + 3]);
- }
- cmd_buff[0] = SONY535_PLAY_AUDIO;
- cmd_buff[1] = 0; /* play back starting at this address */
- /* cmd_buff[2-4] are filled in for loop above */
- cmd_buff[5] = SONY535_PLAY_AUDIO;
- cmd_buff[6] = 2; /* set ending address */
- /* cmd_buff[7-9] are filled in for loop above */
- if ((do_sony_cmd(cmd_buff, 5, status, NULL, 0, 0) != 0) ||
- (do_sony_cmd(cmd_buff + 5, 5, status, NULL, 0, 0) != 0)) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMPLAYMSF)\n",
- status[0]);
- return -EIO;
- }
- /* Save the final position for pauses and resumes */
- final_pos_msf[0] = cmd_buff[7];
- final_pos_msf[1] = cmd_buff[8];
- final_pos_msf[2] = cmd_buff[9];
- sony_audio_status = CDROM_AUDIO_PLAY;
- return 0;
- break;
-
- case CDROMREADTOCHDR: /* Read the table of contents header */
- {
- struct cdrom_tochdr __user *hdr = argp;
- struct cdrom_tochdr loc_hdr;
-
- sony_get_toc();
- if (!sony_toc_read)
- return -EIO;
- loc_hdr.cdth_trk0 = bcd_to_int(sony_toc->first_track_num);
- loc_hdr.cdth_trk1 = bcd_to_int(sony_toc->last_track_num);
- if (copy_to_user(hdr, &loc_hdr, sizeof *hdr))
- return -EFAULT;
- }
- return 0;
- break;
-
- case CDROMREADTOCENTRY: /* Read a given table of contents entry */
- {
- struct cdrom_tocentry __user *entry = argp;
- struct cdrom_tocentry loc_entry;
- int track_idx;
- Byte *msf_val = NULL;
-
- sony_get_toc();
- if (!sony_toc_read) {
- return -EIO;
- }
-
- if (copy_from_user(&loc_entry, entry, sizeof loc_entry))
- return -EFAULT;
-
- /* Lead out is handled separately since it is special. */
- if (loc_entry.cdte_track == CDROM_LEADOUT) {
- loc_entry.cdte_adr = 0 /*sony_toc->address2 */ ;
- loc_entry.cdte_ctrl = sony_toc->control2;
- msf_val = sony_toc->lead_out_start_msf;
- } else {
- track_idx = find_track(int_to_bcd(loc_entry.cdte_track));
- if (track_idx < 0)
- return -EINVAL;
- loc_entry.cdte_adr = 0 /*sony_toc->tracks[track_idx].address */ ;
- loc_entry.cdte_ctrl = sony_toc->tracks[track_idx].control;
- msf_val = sony_toc->tracks[track_idx].track_start_msf;
- }
-
- /* Logical buffer address or MSF format requested? */
- if (loc_entry.cdte_format == CDROM_LBA) {
- loc_entry.cdte_addr.lba = msf_to_log(msf_val);
- } else if (loc_entry.cdte_format == CDROM_MSF) {
- loc_entry.cdte_addr.msf.minute = bcd_to_int(*msf_val);
- loc_entry.cdte_addr.msf.second = bcd_to_int(*(msf_val + 1));
- loc_entry.cdte_addr.msf.frame = bcd_to_int(*(msf_val + 2));
- }
- if (copy_to_user(entry, &loc_entry, sizeof *entry))
- return -EFAULT;
- }
- return 0;
- break;
-
- case CDROMPLAYTRKIND: /* Play a track. This currently ignores index. */
- {
- struct cdrom_ti ti;
- int track_idx;
-
- sony_get_toc();
- if (!sony_toc_read)
- return -EIO;
-
- if (copy_from_user(&ti, argp, sizeof ti))
- return -EFAULT;
- if ((ti.cdti_trk0 < sony_toc->first_track_num)
- || (sony_toc->last_track_num < ti.cdti_trk0)
- || (ti.cdti_trk1 < ti.cdti_trk0)) {
- return -EINVAL;
- }
- track_idx = find_track(int_to_bcd(ti.cdti_trk0));
- if (track_idx < 0)
- return -EINVAL;
- params[1] = sony_toc->tracks[track_idx].track_start_msf[0];
- params[2] = sony_toc->tracks[track_idx].track_start_msf[1];
- params[3] = sony_toc->tracks[track_idx].track_start_msf[2];
- /*
- * If we want to stop after the last track, use the lead-out
- * MSF to do that.
- */
- if (bcd_to_int(sony_toc->last_track_num) <= ti.cdti_trk1) {
- log_to_msf(msf_to_log(sony_toc->lead_out_start_msf) - 1,
- &(params[4]));
- } else {
- track_idx = find_track(int_to_bcd(ti.cdti_trk1 + 1));
- if (track_idx < 0)
- return -EINVAL;
- log_to_msf(msf_to_log(sony_toc->tracks[track_idx].track_start_msf) - 1,
- &(params[4]));
- }
- params[0] = 0x03;
-
- spin_up_drive(status);
-
- set_drive_mode(SONY535_AUDIO_DRIVE_MODE, status);
-
- /* Start the drive at the saved position. */
- cmd_buff[0] = SONY535_PLAY_AUDIO;
- cmd_buff[1] = 0; /* play back starting at this address */
- cmd_buff[2] = params[1];
- cmd_buff[3] = params[2];
- cmd_buff[4] = params[3];
- cmd_buff[5] = SONY535_PLAY_AUDIO;
- cmd_buff[6] = 2; /* set ending address */
- cmd_buff[7] = params[4];
- cmd_buff[8] = params[5];
- cmd_buff[9] = params[6];
- if ((do_sony_cmd(cmd_buff, 5, status, NULL, 0, 0) != 0) ||
- (do_sony_cmd(cmd_buff + 5, 5, status, NULL, 0, 0) != 0)) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMPLAYTRKIND)\n",
- status[0]);
- printk("... Params: %x %x %x %x %x %x %x\n",
- params[0], params[1], params[2],
- params[3], params[4], params[5], params[6]);
- return -EIO;
- }
- /* Save the final position for pauses and resumes */
- final_pos_msf[0] = params[4];
- final_pos_msf[1] = params[5];
- final_pos_msf[2] = params[6];
- sony_audio_status = CDROM_AUDIO_PLAY;
- return 0;
- }
-
- case CDROMSUBCHNL: /* Get subchannel info */
- return sony_get_subchnl_info(argp);
-
- case CDROMVOLCTRL: /* Volume control. What volume does this change, anyway? */
- {
- struct cdrom_volctrl volctrl;
-
- if (copy_from_user(&volctrl, argp, sizeof volctrl))
- return -EFAULT;
- cmd_buff[0] = SONY535_SET_VOLUME;
- cmd_buff[1] = volctrl.channel0;
- cmd_buff[2] = volctrl.channel1;
- if (do_sony_cmd(cmd_buff, 3, status, NULL, 0, 0) != 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMVOLCTRL)\n",
- status[0]);
- return -EIO;
- }
- }
- return 0;
-
- case CDROMEJECT: /* Eject the drive */
- cmd_buff[0] = SONY535_STOP;
- do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
- cmd_buff[0] = SONY535_SPIN_DOWN;
- do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
-
- sony_audio_status = CDROM_AUDIO_INVALID;
- cmd_buff[0] = SONY535_EJECT_CADDY;
- if (do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0) != 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (CDROMEJECT)\n",
- status[0]);
- return -EIO;
- }
- return 0;
- break;
-
- default:
- return -EINVAL;
- }
-}
-
-
-/*
- * Open the drive for operations. Spin the drive up and read the table of
- * contents if these have not already been done.
- */
-static int
-cdu_open(struct inode *inode,
- struct file *filp)
-{
- Byte status[2], cmd_buff[2];
-
- if (sony_inuse)
- return -EBUSY;
- if (check_drive_status() != 0)
- return -EIO;
- sony_inuse = 1;
-
- if (spin_up_drive(status) != 0) {
- printk(CDU535_MESSAGE_NAME " error 0x%.2x (cdu_open, spin up)\n",
- status[0]);
- sony_inuse = 0;
- return -EIO;
- }
- sony_get_toc();
- if (!sony_toc_read) {
- cmd_buff[0] = SONY535_SPIN_DOWN;
- do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
- sony_inuse = 0;
- return -EIO;
- }
- check_disk_change(inode->i_bdev);
- sony_usage++;
-
-#ifdef LOCK_DOORS
- /* disable the eject button while mounted */
- cmd_buff[0] = SONY535_DISABLE_EJECT_BUTTON;
- do_sony_cmd(cmd_buff, 1, status, NULL, 0, 0);
-#endif
-
- return 0;
-}
-
-
-/*
- * Close the drive. Spin it down if no task is using it. The spin
- * down will fail if playing audio, so audio play is OK.
- */
-static int
-cdu_release(struct inode *inode,
- struct file *filp)
-{
- Byte status[2], cmd_no;
-
- sony_inuse = 0;
-
- if (0 < sony_usage) {
- sony_usage--;
- }
- if (sony_usage == 0) {
- check_drive_status();
-
- if (sony_audio_status != CDROM_AUDIO_PLAY) {
- cmd_no = SONY535_SPIN_DOWN;
- do_sony_cmd(&cmd_no, 1, status, NULL, 0, 0);
- }
-#ifdef LOCK_DOORS
- /* enable the eject button after umount */
- cmd_no = SONY535_ENABLE_EJECT_BUTTON;
- do_sony_cmd(&cmd_no, 1, status, NULL, 0, 0);
-#endif
- }
- return 0;
-}
-
-static struct block_device_operations cdu_fops =
-{
- .owner = THIS_MODULE,
- .open = cdu_open,
- .release = cdu_release,
- .ioctl = cdu_ioctl,
- .media_changed = cdu535_check_media_change,
-};
-
-static struct gendisk *cdu_disk;
-
-/*
- * Initialize the driver.
- */
-static int __init sony535_init(void)
-{
- struct s535_sony_drive_config drive_config;
- Byte cmd_buff[3];
- Byte ret_buff[2];
- Byte status[2];
- unsigned long snap;
- int got_result = 0;
- int tmp_irq;
- int i;
- int err;
-
- /* Setting the base I/O address to 0 will disable it. */
- if ((sony535_cd_base_io == 0xffff)||(sony535_cd_base_io == 0))
- return 0;
-
- /* Set up all the register locations */
- result_reg = sony535_cd_base_io;
- command_reg = sony535_cd_base_io;
- data_reg = sony535_cd_base_io + 1;
- read_status_reg = sony535_cd_base_io + 2;
- select_unit_reg = sony535_cd_base_io + 3;
-
-#ifndef USE_IRQ
- sony535_irq_used = 0; /* polling only until this is ready... */
-#endif
- /* we need to poll until things get initialized */
- tmp_irq = sony535_irq_used;
- sony535_irq_used = 0;
-
-#if DEBUG > 0
- printk(KERN_INFO CDU535_MESSAGE_NAME ": probing base address %03X\n",
- sony535_cd_base_io);
-#endif
- /* look for the CD-ROM, follows the procedure in the DOS driver */
- inb(select_unit_reg);
- /* wait for 40 18 Hz ticks (reverse-engineered from DOS driver) */
- schedule_timeout_interruptible((HZ+17)*40/18);
- inb(result_reg);
-
- outb(0, read_status_reg); /* does a reset? */
- snap = jiffies;
- while (jiffies-snap < SONY_JIFFIES_TIMEOUT) {
- select_unit(0);
- if (inb(result_reg) != 0xff) {
- got_result = 1;
- break;
- }
- sony_sleep();
- }
-
- if (!got_result || check_drive_status() == TIME_OUT)
- goto Enodev;
-
- /* CD-ROM drive responded -- get the drive configuration */
- cmd_buff[0] = SONY535_INQUIRY;
- if (do_sony_cmd(cmd_buff, 1, status, (Byte *)&drive_config, 28, 1) != 0)
- goto Enodev;
-
- /* was able to get the configuration,
- * set drive mode as rest of init
- */
-#if DEBUG > 0
- /* 0x50 == CADDY_NOT_INSERTED | NOT_SPINNING */
- if ( (status[0] & 0x7f) != 0 && (status[0] & 0x7f) != 0x50 )
- printk(CDU535_MESSAGE_NAME
- "Inquiry command returned status = 0x%x\n", status[0]);
-#endif
- /* now ready to use interrupts, if available */
- sony535_irq_used = tmp_irq;
-
- /* A negative sony535_irq_used will attempt an autoirq. */
- if (sony535_irq_used < 0) {
- unsigned long irq_mask, delay;
-
- irq_mask = probe_irq_on();
- enable_interrupts();
- outb(0, read_status_reg); /* does a reset? */
- delay = jiffies + HZ/10;
- while (time_before(jiffies, delay)) ;
-
- sony535_irq_used = probe_irq_off(irq_mask);
- disable_interrupts();
- }
- if (sony535_irq_used > 0) {
- if (request_irq(sony535_irq_used, cdu535_interrupt,
- IRQF_DISABLED, CDU535_HANDLE, NULL)) {
- printk("Unable to grab IRQ%d for the " CDU535_MESSAGE_NAME
- " driver; polling instead.\n", sony535_irq_used);
- sony535_irq_used = 0;
- }
- }
- cmd_buff[0] = SONY535_SET_DRIVE_MODE;
- cmd_buff[1] = 0x0; /* default audio */
- if (do_sony_cmd(cmd_buff, 2, status, ret_buff, 1, 1) != 0)
- goto Enodev_irq;
-
- /* set the drive mode successful, we are set! */
- sony_buffer_size = SONY535_BUFFER_SIZE;
- sony_buffer_sectors = sony_buffer_size / CDU535_BLOCK_SIZE;
-
- printk(KERN_INFO CDU535_MESSAGE_NAME " I/F CDROM : %8.8s %16.16s %4.4s",
- drive_config.vendor_id,
- drive_config.product_id,
- drive_config.product_rev_level);
- printk(" base address %03X, ", sony535_cd_base_io);
- if (tmp_irq > 0)
- printk("IRQ%d, ", tmp_irq);
- printk("using %d byte buffer\n", sony_buffer_size);
-
- if (register_blkdev(MAJOR_NR, CDU535_HANDLE)) {
- err = -EIO;
- goto out1;
- }
- sonycd535_queue = blk_init_queue(do_cdu535_request, &sonycd535_lock);
- if (!sonycd535_queue) {
- err = -ENOMEM;
- goto out1a;
- }
-
- blk_queue_hardsect_size(sonycd535_queue, CDU535_BLOCK_SIZE);
- sony_toc = kmalloc(sizeof(struct s535_sony_toc), GFP_KERNEL);
- err = -ENOMEM;
- if (!sony_toc)
- goto out2;
- last_sony_subcode = kmalloc(sizeof(struct s535_sony_subcode), GFP_KERNEL);
- if (!last_sony_subcode)
- goto out3;
- sony_buffer = kmalloc(sizeof(Byte *) * sony_buffer_sectors, GFP_KERNEL);
- if (!sony_buffer)
- goto out4;
- for (i = 0; i < sony_buffer_sectors; i++) {
- sony_buffer[i] = kmalloc(CDU535_BLOCK_SIZE, GFP_KERNEL);
- if (!sony_buffer[i]) {
- while (--i>=0)
- kfree(sony_buffer[i]);
- goto out5;
- }
- }
- initialized = 1;
-
- cdu_disk = alloc_disk(1);
- if (!cdu_disk)
- goto out6;
- cdu_disk->major = MAJOR_NR;
- cdu_disk->first_minor = 0;
- cdu_disk->fops = &cdu_fops;
- sprintf(cdu_disk->disk_name, "cdu");
-
- if (!request_region(sony535_cd_base_io, 4, CDU535_HANDLE)) {
- printk(KERN_WARNING"sonycd535: Unable to request region 0x%x\n",
- sony535_cd_base_io);
- goto out7;
- }
- cdu_disk->queue = sonycd535_queue;
- add_disk(cdu_disk);
- return 0;
-
-out7:
- put_disk(cdu_disk);
-out6:
- for (i = 0; i < sony_buffer_sectors; i++)
- kfree(sony_buffer[i]);
-out5:
- kfree(sony_buffer);
-out4:
- kfree(last_sony_subcode);
-out3:
- kfree(sony_toc);
-out2:
- blk_cleanup_queue(sonycd535_queue);
-out1a:
- unregister_blkdev(MAJOR_NR, CDU535_HANDLE);
-out1:
- if (sony535_irq_used)
- free_irq(sony535_irq_used, NULL);
- return err;
-Enodev_irq:
- if (sony535_irq_used)
- free_irq(sony535_irq_used, NULL);
-Enodev:
- printk("Did not find a " CDU535_MESSAGE_NAME " drive\n");
- return -EIO;
-}
-
-#ifndef MODULE
-
-/*
- * accept "kernel command line" parameters
- * (added by emoenke@gwdg.de)
- *
- * use: tell LILO:
- * sonycd535=0x320
- *
- * the address value has to be the existing CDROM port address.
- */
-static int __init
-sonycd535_setup(char *strings)
-{
- int ints[3];
- (void)get_options(strings, ARRAY_SIZE(ints), ints);
- /* if IRQ change and default io base desired,
- * then call with io base of 0
- */
- if (ints[0] > 0)
- if (ints[1] != 0)
- sony535_cd_base_io = ints[1];
- if (ints[0] > 1)
- sony535_irq_used = ints[2];
- if ((strings != NULL) && (*strings != '\0'))
- printk(CDU535_MESSAGE_NAME
- ": Warning: Unknown interface type: %s\n", strings);
-
- return 1;
-}
-
-__setup("sonycd535=", sonycd535_setup);
-
-#endif /* MODULE */
-
-static void __exit
-sony535_exit(void)
-{
- int i;
-
- release_region(sony535_cd_base_io, 4);
- for (i = 0; i < sony_buffer_sectors; i++)
- kfree(sony_buffer[i]);
- kfree(sony_buffer);
- kfree(last_sony_subcode);
- kfree(sony_toc);
- del_gendisk(cdu_disk);
- put_disk(cdu_disk);
- blk_cleanup_queue(sonycd535_queue);
- if (unregister_blkdev(MAJOR_NR, CDU535_HANDLE) == -EINVAL)
- printk("Uh oh, couldn't unregister " CDU535_HANDLE "\n");
- else
- printk(KERN_INFO CDU535_HANDLE " module released\n");
-}
-
-module_init(sony535_init);
-module_exit(sony535_exit);
-
-
-MODULE_LICENSE("GPL");
-MODULE_ALIAS_BLOCKDEV_MAJOR(CDU535_CDROM_MAJOR);