diff options
Diffstat (limited to 'arch/arm/boot/dts/imx6ul-14x14-evk.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 227 |
1 files changed, 211 insertions, 16 deletions
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi index aa86341adaaa..9c8e1c938340 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi @@ -12,6 +12,19 @@ reg = <0x80000000 0x20000000>; }; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0xa000000>; + linux,cma-default; + }; + }; + backlight_display: backlight-display { compatible = "pwm-backlight"; pwms = <&pwm1 0 5000000>; @@ -20,6 +33,10 @@ status = "okay"; }; + pxp_v4l2 { + compatible = "fsl,imx6ul-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2"; + status = "okay"; + }; reg_sd1_vmmc: regulator-sd1-vmmc { compatible = "regulator-fixed"; @@ -27,6 +44,7 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + off-on-delay-us = <20000>; enable-active-high; }; @@ -61,22 +79,63 @@ "LINPUT3", "Mic Jack", "RINPUT1", "Mic Jack", "RINPUT2", "Mic Jack"; + status = "disabled"; simple-audio-card,cpu { sound-dai = <&sai2>; + status = "disabled"; }; dailink_master: simple-audio-card,codec { sound-dai = <&codec>; clocks = <&clks IMX6UL_CLK_SAI2>; + status = "disabled"; }; }; + sound-wm8960 { + compatible = "fsl,imx6ul-evk-wm8960", + "fsl,imx-audio-wm8960"; + model = "wm8960-audio"; + cpu-dai = <&sai2>; + audio-codec = <&codec>; + asrc-controller = <&asrc>; + codec-master; + gpr = <&gpr 4 0x100000 0x100000>; + /* + * hp-det = <hp-det-pin hp-det-polarity>; + * hp-det-pin: JD1 JD2 or JD3 + * hp-det-polarity = 0: hp detect high for headphone + * hp-det-polarity = 1: hp detect high for speaker + */ + hp-det = <3 0>; + hp-det-gpios = <&gpio5 4 0>; + mic-det-gpios = <&gpio5 4 0>; + audio-routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Ext Spk", "SPK_LP", + "Ext Spk", "SPK_LN", + "Ext Spk", "SPK_RP", + "Ext Spk", "SPK_RN", + "LINPUT2", "Mic Jack", + "LINPUT3", "Mic Jack", + "RINPUT1", "Main MIC", + "RINPUT2", "Main MIC", + "Mic Jack", "MICB", + "Main MIC", "MICB", + "CPU-Playback", "ASRC-Playback", + "Playback", "CPU-Playback", + "ASRC-Capture", "CPU-Capture", + "CPU-Capture", "Capture"; + }; + spi4 { compatible = "spi-gpio"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi4>; status = "okay"; + pinctrl-assert-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; gpio-sck = <&gpio5 11 0>; gpio-mosi = <&gpio5 10 0>; cs-gpios = <&gpio5 7 0>; @@ -90,20 +149,10 @@ #gpio-cells = <2>; reg = <0>; registers-number = <1>; + registers-default = /bits/ 8 <0x57>; spi-max-frequency = <100000>; }; }; - - panel { - compatible = "innolux,at043tn24"; - backlight = <&backlight_display>; - - port { - panel_in: endpoint { - remote-endpoint = <&display_out>; - }; - }; - }; }; &clks { @@ -111,6 +160,16 @@ assigned-clock-rates = <786432000>; }; +&csi { + status = "disabled"; + + port { + csi1_ep: endpoint { + remote-endpoint = <&ov5640_ep>; + }; + }; +}; + &i2c2 { clock-frequency = <100000>; pinctrl-names = "default"; @@ -122,6 +181,28 @@ compatible = "wlf,wm8960"; reg = <0x1a>; wlf,shared-lrclk; + clocks = <&clks IMX6UL_CLK_SAI2>; + clock-names = "mclk"; + }; + + ov5640: ov5640@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_csi1>; + clocks = <&clks IMX6UL_CLK_CSI>; + clock-names = "csi_mclk"; + pwn-gpios = <&gpio_spi 6 1>; + rst-gpios = <&gpio_spi 5 0>; + csi_id = <0>; + mclk = <24000000>; + mclk_source = <0>; + status = "disabled"; + port { + ov5640_ep: endpoint { + remote-endpoint = <&csi1_ep>; + }; + }; }; }; @@ -183,6 +264,15 @@ mag3110@e { compatible = "fsl,mag3110"; reg = <0x0e>; + position = <2>; + }; + + fxls8471@1e { + compatible = "fsl,fxls8471"; + reg = <0x1e>; + position = <0>; + interrupt-parent = <&gpio5>; + interrupts = <0 8>; }; }; @@ -192,11 +282,31 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>; + display = <&display0>; status = "okay"; - port { - display_out: endpoint { - remote-endpoint = <&panel_in>; + display0: display@0 { + bits-per-pixel = <16>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + + timing0: timing0 { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; }; }; }; @@ -207,6 +317,10 @@ status = "okay"; }; +&pxp { + status = "okay"; +}; + &qspi { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_qspi>; @@ -242,6 +356,22 @@ status = "okay"; }; +&sim2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sim2>; + assigned-clocks = <&clks IMX6UL_CLK_SIM_SEL>; + assigned-clock-parents = <&clks IMX6UL_CLK_SIM_PODF>; + assigned-clock-rates = <240000000>; + /* GPIO_ACTIVE_HIGH/LOW:sim card voltage control + * NCN8025:Vcc = ACTIVE_HIGH?5V:3V + * TDA8035:Vcc = ACTIVE_HIGH?5V:1.8V + */ + pinctrl-assert-gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; + port = <1>; + sven_low_active; + status = "okay"; +}; + &tsc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_tsc>; @@ -261,11 +391,16 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; uart-has-rtscts; + /* for DTE mode, add below change */ + /* fsl,dte-mode; */ + /* pinctrl-0 = <&pinctrl_uart2dte>; */ status = "okay"; }; &usbotg1 { dr_mode = "otg"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1>; status = "okay"; }; @@ -298,7 +433,7 @@ &usdhc2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2>; - no-1-8-v; + non-removable; keep-power-in-suspend; wakeup-source; status = "okay"; @@ -499,10 +634,25 @@ >; }; + pinctrl_uart2dte: uart2dtegrp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX 0x1b0b1 + MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART2_DTE_CTS 0x1b0b1 + MX6UL_PAD_UART3_TX_DATA__UART2_DTE_RTS 0x1b0b1 + >; + }; + + pinctrl_usb_otg1: usbotg1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059 + >; + }; + pinctrl_usdhc1: usdhc1grp { fsl,pins = < MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 - MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071 MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 @@ -547,6 +697,51 @@ >; }; + pinctrl_usdhc2_8bit: usdhc2grp_8bit { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059 + MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059 + MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059 + MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059 + >; + }; + + pinctrl_usdhc2_8bit_100mhz: usdhc2grp_8bit_100mhz { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9 + MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9 + MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9 + MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc2_8bit_200mhz: usdhc2grp_8bit_200mhz { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9 + MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9 + MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9 + MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9 + >; + }; + pinctrl_wdog: wdoggrp { fsl,pins = < MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0 |