diff options
Diffstat (limited to 'docs/plat/marvell/build.txt')
| -rw-r--r-- | docs/plat/marvell/build.txt | 194 |
1 files changed, 0 insertions, 194 deletions
diff --git a/docs/plat/marvell/build.txt b/docs/plat/marvell/build.txt deleted file mode 100644 index 7b75196f..00000000 --- a/docs/plat/marvell/build.txt +++ /dev/null @@ -1,194 +0,0 @@ -TF-A Build Instructions -====================== - -This section describes how to compile the ARM Trusted Firmware (TF-A) project for Marvell's platforms. - -Build Instructions ------------------- -(1) Set the cross compiler:: - - > export CROSS_COMPILE=/path/to/toolchain/aarch64-linux-gnu- - -(2) Set path for FIP images: - - Set U-Boot image path (relatively to TF-A root or absolute path):: - - > export BL33=path/to/u-boot.bin - - For example: if U-Boot project (and its images) is located at ~/project/u-boot, - BL33 should be ~/project/u-boot/u-boot.bin - - .. note:: - - u-boot.bin should be used and not u-boot-spl.bin - - Set MSS/SCP image path (mandatory only for Armada80x0):: - - > export SCP_BL2=path/to/mrvl_scp_bl2*.img - -(3) Armada-37x0 build requires WTP tools installation. - - See below in the section "Tools and external components installation". - Install ARM 32-bit cross compiler, which is required for building WTMI image for CM3:: - - > sudo apt-get install gcc-arm-linux-gnueabi - -(4) Clean previous build residuals (if any):: - - > make distclean - -(5) Build TF-A: - - There are several build options: - - - DEBUG: default is without debug information (=0). in order to enable it use DEBUG=1 - Must be disabled when building UART recovery images due to current console driver - implementation that is not compatible with Xmodem protocol used for boot image download. - - - LOG_LEVEL: defines the level of logging which will be purged to the default output port. - - LOG_LEVEL_NONE 0 - LOG_LEVEL_ERROR 10 - LOG_LEVEL_NOTICE 20 - LOG_LEVEL_WARNING 30 - LOG_LEVEL_INFO 40 - LOG_LEVEL_VERBOSE 50 - - - USE_COHERENT_MEM: This flag determines whether to include the coherent memory region in the - BL memory map or not. - - - LLC_ENABLE: Flag defining the LLC (L3) cache state. The cache is enabled by default (LLC_ENABLE=1). - - - MARVELL_SECURE_BOOT: build trusted(=1)/non trusted(=0) image, default is non trusted. - - - BLE_PATH: - Points to BLE (Binary ROM extension) sources folder. Only required for A8K builds. - The parameter is optional, its default value is "plat/marvell/a8k/common/ble". - - - MV_DDR_PATH: - For A7/8K, use this parameter to point to mv_ddr driver sources to allow BLE build. For A37x0, - it is used for ddr_tool build. - Usage example: MV_DDR_PATH=path/to/mv_ddr - The parameter is optional for A7/8K, when this parameter is not set, the mv_ddr - sources are expected to be located at: drivers/marvell/mv_ddr. However, the parameter - is necessary for A37x0. - For the mv_ddr source location, check the section "Tools and external components installation" - - - DDR_TOPOLOGY: For Armada37x0 only, the DDR topology map index/name, default is 0. - Supported Options: - - DDR3 1CS (0): DB-88F3720-DDR3-Modular (512MB); EspressoBIN (512MB) - - DDR4 1CS (1): DB-88F3720-DDR4-Modular (512MB) - - DDR3 2CS (2): EspressoBIN V3-V5 (1GB) - - DDR4 2CS (3): DB-88F3720-DDR4-Modular (4GB) - - DDR3 1CS (4): DB-88F3720-DDR3-Modular (1GB) - - DDR4 1CS (5): EspressoBin V7 (1GB) - - DDR4 2CS (6): EspressoBin V7 (2GB) - - CUSTOMER (CUST): Customer board, DDR3 1CS 512MB - - - CLOCKSPRESET: For Armada37x0 only, the clock tree configuration preset including CPU and DDR frequency, - default is CPU_800_DDR_800. - - CPU_600_DDR_600 - CPU at 600 MHz, DDR at 600 MHz - - CPU_800_DDR_800 - CPU at 800 MHz, DDR at 800 MHz - - CPU_1000_DDR_800 - CPU at 1000 MHz, DDR at 800 MHz - - CPU_1200_DDR_750 - CPU at 1200 MHz, DDR at 750 MHz - - - BOOTDEV: For Armada37x0 only, the flash boot device, default is SPINOR, - Currently, Armada37x0 only supports SPINOR, SPINAND, EMMCNORM and SATA: - - - SPINOR - SPI NOR flash boot - - SPINAND - SPI NAND flash boot - - EMMCNORM - eMMC Download Mode - Download boot loader or program code from eMMC flash into CM3 or CA53 - Requires full initialization and command sequence - - SATA - SATA device boot - - - PARTNUM: For Armada37x0 only, the boot partition number, default is 0. To boot from eMMC, the value - should be aligned with the parameter in U-Boot with name of CONFIG_SYS_MMC_ENV_PART, whose - value by default is 1. - For details about CONFIG_SYS_MMC_ENV_PART, please refer to the U-Boot build instructions. - - - WTMI_IMG: For Armada37x0 only, the path of the WTMI image can point to an image which does - nothing, an image which supports EFUSE or a customized CM3 firmware binary. The default image - is wtmi.bin that built from sources in WTP folder, which is the next option. If the default - image is OK, then this option should be skipped. - - - WTP: For Armada37x0 only, use this parameter to point to wtptools source code directory, which - can be found as a3700_utils.zip in the release. - Usage example: WTP=/path/to/a3700_utils - - For example, in order to build the image in debug mode with log level up to 'notice' level run:: - - > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 PLAT=<MARVELL_PLATFORM> all fip - - And if we want to build a Armada37x0 image in debug mode with log level up to 'notice' level, - the image has the preset CPU at 1000 MHz, preset DDR3 at 800 MHz, the DDR topology of DDR4 2CS, - the image boot from SPI NOR flash partition 0, and the image is non trusted in WTP, the command - line is as following:: - - > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 CLOCKSPRESET=CPU_1000_DDR_800 \ - MARVELL_SECURE_BOOT=0 DDR_TOPOLOGY=3 BOOTDEV=SPINOR PARTNUM=0 PLAT=a3700 all fip - - Supported MARVELL_PLATFORM are: - - a3700 (for both A3720 DB and EspressoBin) - - a70x0 - - a70x0_amc (for AMC board) - - a80x0 - - a80x0_mcbin (for MacciatoBin) - -Special Build Flags --------------------- - - PLAT_RECOVERY_IMAGE_ENABLE: When set this option to enable secondary recovery function when build - atf. In order to build UART recovery image this operation should be disabled for a70x0 and a80x0 - because of hardware limitation (boot from secondary image can interrupt UART recovery process). - This MACRO definition is set in plat/marvell/a8k/common/include/platform_def.h file - -(for more information about build options, please refer to section 'Summary of build options' in TF-A user-guide: - https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/user-guide.md) - - -Build output -------------- -Marvell's TF-A compilation generates 7 files: - - ble.bin - BLe image - - bl1.bin - BL1 image - - bl2.bin - BL2 image - - bl31.bin - BL31 image - - fip.bin - FIP image (contains BL2, BL31 & BL33 (U-Boot) images) - - boot-image.bin - TF-A image (contains BL1 and FIP images) - - flash-image.bin - Image which contains boot-image.bin and SPL image; - should be placed on the boot flash/device. - - -Tools and external components installation -========================================== - -Armada37x0 Builds require installation of 3 components -------------------------------------------------------- - -(1) ARM cross compiler capable of building images for the service CPU (CM3). - This component is usually included in the Linux host packages. - On Debian/Ubuntu hosts the default GNU ARM tool chain can be installed - using the following command:: - - > sudo apt-get install gcc-arm-linux-gnueabi - - Only if required, the default tool chain prefix "arm-linux-gnueabi-" can be - overwritten using the environment variable CROSS_CM3. - Example for BASH shell:: - - > export CROSS_CM3=/opt/arm-cross/bin/arm-linux-gnueabi - -(2) DDR initialization library sources (mv_ddr) available at the following repository - (use the "mv_ddr-armada-atf-mainline" branch):: - https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git - -(3) Armada3700 tools available at the following repository (use the latest release branch):: - https://github.com/MarvellEmbeddedProcessors/A3700-utils-marvell.git - -Armada70x0 and Armada80x0 Builds require installation of an additional component --------------------------------------------------------------------------------- - -(1) DDR initialization library sources (mv_ddr) available at the following repository - (use the "mv_ddr-armada-atf-mainline" branch):: - https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git - |