Age | Commit message (Collapse) | Author |
|
Add a device tree overlay for resistive touch enablement.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Related-to: ELB-4380
Signed-off-by: Henrique Garcia <henrique.garcia@toradex.com>
|
|
Apalis iMX8X is no longer supported.
Drop overlays support for this target
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Verdin iMX8M Mini DualLite does not have a can interface
which leads to the following message in the boot log.
[ 8.752956] mcp25xxfd spi2.0: CRC read error: computed: 6c2a received: ffff - data: be 00 04 ff ff ff ff
[ 8.782993] mcp25xxfd spi2.0: CRC read of clock register resulted in a bad CRC mismatch - hw not found
[ 8.863803] mcp25xxfd spi2.0: Probe failed, err=84
This overlay disables the CAN1 node to avoid error messages in dmesg.
Related-to: ELB-4187
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Use common naming conventions for all mezzanine overlays
- apalis-imx8_mezzanine_lvds_overlay.dts - LVDS 10"
- apalis-imx8_mezzanine_ov5640_overlay.dts - CSI_2 OV5640 camera
Related-to: ELB-2578
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Enable flexcan3 interface. Keep CAN transceiver
Silent Mode OFF MXM Pin 193 (GPIO2_IO18) low.
Related-to: ELB-2578
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Add following overlays:
- Parallel RGB/VGA support
- Atmel MXT TS for boards with Capacitive Touch Connector
- Atmel MXT TS for Capacitive Touch Adapter
- Fusion F0710A TS for boards with Capacitive Touch Connector
- Fusion F0710A TS for Capacitive Touch Adapter
- Toradex 7" touchscreen lt161010
- Toradex 10" touchscreen lt170410
- Toradex 7" resistive touchscreen ad7879
Related-to: ELB-4065
Related-to: ELB-4080
Signed-off-by: Oleksii Bidnichenko <oleksii.bidnichenko@toradex.com>
|
|
Add separate overlay for Apalis iMX8 Mezzanine
available on the evaluation board.
Mezzanine is using ldb1 for the LVDS lane,
configure lvds-channel appropriately
Related-to: ELB-2578
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
verdin-imx8mp_mezzanine-ov5640_overlay.dts:
Modify the regular overlay to work with the default jumpering of the
Mezzanine which uses the same GPIOs as the first camera interface CSI_1
and the same I2C bus as used for DSI display adapters! So, unless we
modify the OV5640 driver to cope with using them same GPIOs twice or
ignore absence of GPIOs this will not work for any concurrent dual
camera use case.
verdin-imx8mp_mezzanine-ov5640-2_overlay.dts:
Add a new overlay to work with an alternate jumpering of the Mezzanine
which uses the same Verdin GPIO2 as used for the Atmel MXT Touchscreen
and the same I2C bus as used for DSI display adapters! So, while this
can not concurrently used with our 10 inch capacitive LVDS touch screen
it does work fine for any concurrent dual camera use case.
While at it indicate GPIO usage of primary CSI_1 OV5640 overlay.
Related-to: ELB-4035
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Related-to: ELB-4035
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Related-to: ELB-4034
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Related-to: ELB-4034
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Related-to: ELB-4034
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Add support of the MIPI CSI-2 serial camera OV5640.
Related-to: ELB-3883
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Re-add an overlay, which uses mxsfb driver. It supports additional
panel/display flags.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Rename parallel-rgb to display-lcdif overlay as it uses DPU-enabled
LCDIF interface driver (display_lcdif). It doesn't support additional
panel/display flags, however it works more stable, than mxsfb driver,
and supports higher resolutions up to 4k.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add an overlay, which uses DPU-enabled LCDIF interface driver
(display_lcdif). It doesn't support additional panel/display flags,
however it works more stable, than mxsfb driver, and supports higher
resolutions up to 4k.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The EDT 7" resistive panel latches data on the rising edge.
Add the overlay to support this panel more precisely.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The EDT 7" resistive panel latches data on the rising edge.
Add the overlay to support this panel more precisely.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The EDT 7" resistive panel latches data on the rising edge.
Add the overlay to support this panel more precisely.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add device tree overlay for CSI Camera Module 5MP OV5640 previously
orderable at Toradex.
Related-to: ELB-3883
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
This allows for disabling the UART B in Linux freeing it for potential
M4 use.
Related-to: ELB-3520
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add device tree overlay for CSI Camera Module 5MP OV5640 previously
orderable at Toradex.
Related-to: ELB-3883
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add the overlay to support LCD-LVDS transceiver on Iris v2.0A.
Related-to: ELB-3876
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add device tree overlay for Verdin DSI to LVDS Adapter and a connected
10 inch display lt170410 orderable at Toradex.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Cosmetic clean-up without any functional impact:
- re-order overlays in Makefile alphabetically
- get rid of obsolete includes
- add note that CSI Camera Module 5MP OV5640 is no longer orderable at
Toradex
- re-order properties alphabetically
- re-order nodes alphabetically
- fix indentation and line-spacing
- use correct NXP SoC naming nomenclature
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Fix dtb vs. dtg typo in Makefile.
Note: This has no impact on our builds as the OpenEmbedded recipe does
not make use of that Makefile.
Fixes: 3079c64e090a ("overlays: colibri-imx7: overlay for 10" LVDS")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add device tree overlay for CSI Camera Module 5MP OV5640 previously
orderable at Toradex.
Related to: ELB-3365
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add the device tree overlay for the Verdin native HDMI output
interface.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Fix resolution in LCD overlay, so that the Capacitive/Resistive
Touch 7" Displays work well.
Rename the overlay to reflect the fact that it supports LT161010
display.
Related-to: ELB-3240
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Fix resolution and bus width in LVDS overlay, so that the
Capacitive Touch 10" Display works well.
Rename the overlay to reflect the fact that it supports
LT170410 display.
Related-to: ELB-3240
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add overlay for 10" LVDS touchscreen lt170410
Related-to: ELB-3548
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
The VGA connects to the lcdif interface available
in imx7-colibri.dtsi. This overlay enables VGA
interface overlay for boards supporting VGA.
Related-to: ELB-3547
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Add overlays for:
- Atmel MXT TS for boards with Capacitive Touch Connector
- Atmel MXT TS for Capacitive Touch Adapter
- Fusion F0710A TS for boards with Capacitive Touch Connector
- Fusion F0710A TS for Capacitive Touch Adapter
Related-to: ELB-3547
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Add overlays for:
- Atmel MXT TS for boards with Capacitive Touch Connector
- Atmel MXT TS for Capacitive Touch Adapter
- Fusion F0710A TS for boards with Capacitive Touch Connector
- Fusion F0710A TS for Capacitive Touch Adapter
Related-to: ELB-3243
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add an overlay that supports connecting displays with
Capacitive Touch Adapter.
Simplify atmel mxt overlays.
Now the common scheme for atmel mxt overlays:
atmel-mxt-connector - uses 107/106 pins for INT/Reset signals;
atmel-mxt-adapter - uses 28/30 pins for INT/Reset signals.
Related-to: ELB-3246
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The LT8912 DSI-HDMI bridge and related subsystems remain disabled in
the main devicetree. Add the overlay to let the system use an HDMI
output.
Related-to: ELB-3426, ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Move all non conflicting properties into nodes of the main device tree and
just set the status to okay for those nodes.
Split the touch controller from the lvds controller's overlay into its own.
This unifies with the way it is done for the Verdin iMX8M Plus.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
The resistive 7" panel which should work by default on all colibri
modules has a resolution 800x480. Choose the proper settings for
this panel. Rename the overlay to reflect these changes.
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
All Toradex 7" displays support 800x480 mode. Preset this mode
it the overlay.
Related-to: ELB-3243
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add an overlay to enable a Parallel RGB interface with setting
to support an LCD-LVDS converter and Toradex Capacitive 10" Display.
Related-to: ELB-3243
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The VGA connects to the LCD interface, which remains disabled in the
main devicetree. Add an overlay that turns it on and set up the
VGA display mode, making one able to use VGA monitors.
Related-to: ELB-3243
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Apalis-iMX6Q/Colibri-iMX6DL support FullHD mode on HDMI interface. If
there is VGA mode available in EDID, the mxcfb driver choose it by
default.
This overlay tells the mxcfb driver to prefer switching to FullHD mode,
if available.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The HDMI interface and related stuff remain disabled in the main
devicetree. Add the overlay that turns it on, enabling to use HDMI
monitors.
Related-to: ELB-3243
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add an overlay to support the standard VGA monitor.
Related-to: ELB-3246
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The HDMI interface and related stuff remain disabled in the main
devicetree. Add the overlay to be able using it with HDMI monitors.
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The AD7879 resistive touchscreen device remains disabled in the main
devicetree. Add the overlay which turns it on for using with a
Resistive Touch Display 7".
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add an overlay to enable an LCDIF (Parallel RGB) interface and
all related subsystems.
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Fusion 7 touchscreen uses same I2C1 pins as Atmel MXT.
Enable fusion_f0710a and disable atmel_mxt_ts in this overlay.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
The STMPE resistive touchscreen device remains disabled in the main devicetree.
Add the overlay to be able using it with Resistive Touch Display 7".
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|